Superhuman Hearing - Virtual Prototyping of Artificial Hearing: a Case Study on Interactions and Acoustic Beamforming.

Directivity and gain in microphone array systems for hearing aids or hearable devices allow users to acoustically enhance the information of a source of interest. This source is usually positioned directly in front. This feature is called acoustic beamforming. The current study aimed to improve users' interactions with beamforming via a virtual prototyping approach in immersive virtual environments (VEs). Eighteen participants took part in experimental sessions composed of a calibration procedure and a selective auditory attention voice-pairing task. Eight concurrent speakers were placed in an anechoic environment in two virtual reality (VR) scenarios. The scenarios were a purely virtual scenario and a realistic 360° audio-visual recording. Participants were asked to find an individual optimal parameterization for three different virtual beamformers: (i) head-guided, (ii) eye gaze-guided, and (iii) a novel interaction technique called dual beamformer, where head-guided is combined with an additional hand-guided beamformer. None of the participants were able to complete the task without a virtual beamformer (i.e., in normal hearing condition) due to the high complexity introduced by the experimental design. However, participants were able to correctly pair all speakers using all three proposed interaction metaphors. Providing superhuman hearing abilities in the form of a dual acoustic beamformer guided by head and hand movements resulted in statistically significant improvements in terms of pairing time, suggesting the task-relevance of interacting with multiple points of interests.

In vivo validation of a blood vector velocity estimator with MR angiography.

Conventional Doppler methods for blood velocity estimation only estimate the velocity component along the ultrasound beam direction. This implies that a Doppler angle under examination close to 90 degrees results in unreliable information about the true blood direction and blood velocity. The novel method transverse oscillation (TO), which combines estimates of the axial and the transverse velocity components in the scan plane, makes it possible to estimate the vector velocity of the blood regardless of the Doppler angle. The present study evaluates the TO method with magnetic resonance phase contrast angiography (MRA) by comparing in vivo measurements of stroke volume. Eleven healthy volunteers were included in this prospective study. From the obtained data sets recorded with the 2 modalities, vector velocity sequences were constructed and stroke volume calculated. Angle of insonation was approximately 90 degrees for TO measurements. The correlation between the stroke volume estimated by TO and MRA was 0.91 (p < 0.01) with the equation for the line of regression: MRA = 1.1.TO-0.4. A Bland-Altman plot was additionally constructed where the mean difference was 0.2 ml with limits of agreement at -1.4 ml and 1.9 ml. The results indicate that reliable vector velocity estimates can be obtained in vivo using the presented angle-independent 2-D vector velocity method. The TO method can be a useful alternative to conventional Doppler systems by avoiding the angle artifact, thus giving quantitative velocity information.

Coded ultrasound for blood flow estimation using subband processing.

This paper investigates the use of coded excitation for blood flow estimation in medical ultrasound. Traditional autocorrelation estimators use narrow-band excitation signals to provide sufficient signal-to-noise-ratio (SNR) and velocity estimation performance. In this paper, broadband coded signals are used to increase SNR, followed by subband processing. The received broadband signal is filtered using a set of narrow-band filters. Estimating the velocity in each of the bands and averaging the results yields better performance compared with what would be possible when transmitting a narrow-band pulse directly. Also, the spatial resolution of the narrow-band pulse would be too poor for brightness-mode (B-mode) imaging, and additional transmissions would be required to update the B-mode image. For the described approach in the paper, there is no need for additional transmissions, because the excitation signal is broadband and has good spatial resolution after pulse compression. This means that time can be saved by using the same data for B-mode imaging and blood flow estimation. Two different coding schemes are used in this paper, Barker codes and Golay codes. The performance of the codes for velocity estimation is compared with a conventional approach transmitting a narrow-band pulse. The study was carried out using an experimental ultrasound scanner and a commercial linear array 7 MHz transducer. A circulating flow rig was scanned with a beam-to-flow angle of 60 degrees. The flow in the rig was laminar and had a parabolic flow-profile with a peak velocity of 0.09 m/s. The mean relative standard deviation of the velocity estimate using the reference method with an 8-cycle excitation pulse at 7 MHz was 0.544% compared with the peak velocity in the rig. Two Barker codes were tested with a length of 5 and 13 bits, respectively. The corresponding mean relative standard deviations were 0.367% and 0.310%, respectively. For the Golay coded experiment, two 8-bit codes were used, and the mean relative standard deviation was 0.335%.

High frame-rate blood vector velocity imaging using plane waves: simulations and preliminary experiments.

Conventional ultrasound methods for acquiring color images of blood velocity are limited by a relatively low frame-rate and are restricted to give velocity estimates along the ultrasound beam direction only. To circumvent these limitations, the method presented in this paper uses 3 techniques: 1) The ultrasound is not focused during the transmissions of the ultrasound signals; 2) A 13-bit Barker code is transmitted simultaneously from each transducer element; and 3) The 2-D vector velocity of the blood is estimated using 2-D cross-correlation. A parameter study was performed using the Field II program, and performance of the method was investigated when a virtual blood vessel was scanned by a linear array transducer. An improved parameter set for the method was identified from the parameter study, and a flow rig measurement was performed using the same improved setup as in the simulations. Finally, the common carotid artery of a healthy male was scanned with a scan sequence that satisfies the limits set by the Food and Drug Administration. Vector velocity images were obtained with a frame-rate of 100 Hz where 40 speckle images are used for each vector velocity image. It was found that the blood flow approximately followed the vessel wall, and that maximum velocity was approximately 1 m/s, which is a normal value for a healthy person. To further evaluate the method, the test person was scanned with magnetic resonance (MR) angiography. The volume flow derived from the MR scanning was compared with that from the ultrasound scanning. A deviation of 9% between the 2 volume flow estimates was found.

Examples of in vivo blood vector velocity estimation.

In this paper, a case study of in-vivo blood vector velocity images of the carotid artery are presented. The transverse oscillation (TO) method for blood vector velocity estimation has been used to estimate the vector velocities. The carotid arteries of three healthy volunteers are scanned in-vivo at three different positions by experienced sonographers. The scanning regions are: 1) the common carotid artery at 88 degrees beam to flow angle, 2) the common carotid artery and the jugular vein at approximately 90 degrees beam to flow angle and 3) the bifurcation of the carotid artery. The resulting velocity estimates are displayed as vector velocity images, where the velocity vector is superimposed on a B-mode image showing the tissue structures. The volume flow is found for case 1) and when compared with MRI from the literature, a bias of approximately approximately 20% is found. The maximum flow velocity within the carotid artery is found to be 0.8 m/s, which is normal for a healthy person. In case 3), the estimated vector velocities are compared with numerical simulations. Qualitatively similar flow pattern can be seen in both simulations and in the vector velocity images. Furthermore, a vortex is identified in the carotid sinus at the deceleration phase after the peak systole. This vortex is seen in all of the three acquired cardiac cycles.

Investigation of transverse oscillation method.

Conventional ultrasound scanners can display only the axial component of the blood velocity vector, which is a significant limitation when vessels nearly parallel to the skin surface are scanned. The transverse oscillation (TO) method overcomes this limitation by introducing a TO and an axial oscillation in the pulse echo field. The theory behind the creation of the double oscillation pulse echo field is explained as well as the theory behind the estimation of the vector velocity. A parameter study of the method is performed, using the ultrasound simulation program Field II. A virtual linear-array transducer with center frequency 7 MHz and 128 active elements is created, and a virtual blood vessel of radius 6.4 mm is simulated. The performance of the TO method is found around an initial point in the parameter space. The parameters varied are: flow angle, transmit focus depth, receive apodization, pulse length, transverse wave length, number of emissions, signal-to-noise ratio (SNR), and type of echo-canceling filter used. Using an experimental scanner, the performance of the TO method is evaluated. An experimental flowrig is used to create laminar parabolic flow in a blood mimicking fluid, and the fluid is scanned under different flow-to-beam angles. The relative standard deviation on the transverse velocity estimate is found to be less than 10% for all angles between 50 degrees and 90 degrees. Furthermore, the TO method is evaluated in the flowrig using pulsatile flow, which resembles the flow in the femoral artery. The estimated volume flow as a function of time is compared to the volume flow derived from a conventional axial method at a flow-to-beam angle of 60 degrees. It is found that the method is highly sensitive to the angle between the flow and the beam direction. Also, the choice of echo canceling filter affects the performance significantly.