The role of mechanical collapse by cryogenic ball milling on the effect of high-pressure homogenization on the microstructural and texturizing properties of partially pectin-depleted tomato cell wall material.

In the current study, the effect of different particle size reduction techniques, namely high-pressure homogenization (HPH) and cryogenic ball milling (CBM), on the microstructural and texturizing properties of the tomato acid-unextractable fraction (AcUF) in suspension was studied. Partial pectin depletion was performed by nitric acid pectin extraction on the alcohol-insoluble residue. In the absence of the aforementioned mechanical treatments, the partially pectin-depleted material, i.e., the AcUF, showed a cellular morphology and a high texturizing potential. By short-time CBM in dry-state, the AcUF was extensively fractured and clumped, resulting in a collapsed structure with negligible texturizing potential and low water binding capacity. In contrast, HPH could disrupt the cell wall network (destroying the cellular morphology) resulting in a continuum of interacting material having very similar texturizing potential and a slightly higher water binding capacity than the AcUF before HPH. Furthermore, the potential of HPH to (re)functionalize the collapsed cryogenic ball milled AcUF by its shear-induced disruption was shown. Indeed, the debris-like cell wall remnants could to some extent be reopened by HPH, which resulted in a partial recovery of the original texturizing potential and an improved water binding capacity. However, the potential of HPH at 20 MPa to revert the detrimental effect of CBM decreased with increasing CBM treatment time.

Microstructural and Texturizing Properties of Partially Pectin-Depleted Cell Wall Material: The Role of Botanical Origin and High-Pressure Homogenization.

In the current study, the texturizing properties of partially pectin-depleted cell wall material (CWM) of apple, carrot, onion and pumpkin, and the potential of functionalization by high-pressure homogenization (HPH) were addressed. This partially pectin-depleted CWM was obtained as the unextractable fraction after acid pectin extraction (AcUF) on the alcohol-insoluble residue. Chemical analysis was performed to gain insight into the polysaccharide composition of the AcUF. The microstructural and functional properties of the AcUF in suspension were studied before HPH and after HPH at 20 and 80 MPa. Before HPH, even after the pectin extraction, the particles showed a cell-like morphology and occurred separately in the apple, onion and pumpkin AcUF and in a clustered manner in the carrot AcUF. The extent of disruption by the HPH treatments at 20 and 80 MPa was dependent on the botanical origin. Only for the onion and pumpkin AcUF, the water binding capacity was increased by HPH. Before HPH, the texturizing potential of the AcUFs was greatly varying between the different matrices. Whereas HPH improved the texturizing potential of the pumpkin AcUF, no effect and even a decrease was observed for the onion AcUF and the apple and carrot AcUF, respectively.

The Structure and Composition of Extracted Pectin and Residual Cell Wall Material from Processing Tomato: The Role of a Stepwise Approach versus High-Pressure Homogenization-Facilitated Acid Extraction.

In literature, different pectin extraction methods exist. In this study, two approaches starting from the alcohol-insoluble residue (AIR) of processing tomato are performed in a parallel way to facilitate the comparison of pectin yield and the compositional and structural properties of the extracted pectin and residual cell wall material obtained. On the one hand, pectin is extracted stepwise using hot water, chelating agents and low-alkaline conditions targeting fractionation of the pectin population. On the other hand, an industrially relevant single-step nitric acid pectin extraction (pH 1.6) is performed. In addition to these conventional solvent pectin extractions, the role of high-pressure homogenization (HPH) as a physically disruptive treatment to facilitate further pectin extraction from the partially pectin-depleted fraction obtained after acid extraction is addressed. The impact of HPH on the pectin cell wall polysaccharide interactions was shown as almost two thirds of the residual pectin were extractable during the subsequent extractions. For both extraction approaches, pectin obtained further in the sequence was characterized by a higher molecular mass and a higher amount of rhamnogalacturonan I domains. The estimated hemicellulose and cellulose content increased from 56 mol% for the AIR to almost 90 mol% for the final unextractable fractions of both methods.