Off-gassing from firefighter suits (nomex) as an indoor source of BTEXS.

The clothes and special equipment of firefighters can be a source of indoor air pollution. Nevertheless, it has not been investigated so far what the scale of the release of various compounds from such materials into the indoor air can be. The following study analysed the results of an experiment involving the passive measurement of concentrations of selected compounds, i.a. benzene, toluene, ethylbenzene, m,p-xylene, o-xylene, styrene, isopropylbenzene and n-propylbenzene (BTEXS) in the air of a room where firefighters' special clothing, which had been previously exposed to emissions from simulated fires, was stored. The study included simulations of fires involving three materials: wood, processed wood (OSB/fibreboard) and a mixture of plastics. After being exposed to the simulated fire environment, special clothing (so-called nomex) was placed in a sealed chamber, where passive collection of BTEXS was carried out using tube-type axial passive samplers and a gas chromatograph. Irrespective of which burned material special clothing was exposed to, the compound emitted into the air most intensively was toluene. Its rate of release from a single nomex ranges from 4.4 to 28.6 µg h-1, while the corresponding rates for the sum of BTEXS are between 9.97 and 44.29 µg h-1.

Analysis of Side Effects Following Vaccination Against COVID-19 Among Individuals With Multiple Sclerosis Treated With DMTs in Poland.

Background and Objectives: Since vaccination against COVID-19 is available for over a year and the population of immunized individuals with autoimmune disorders is higher than several months before, an evaluation of safety and registered adverse events can be made. We conducted a large study of side effects following the COVID-19 vaccine among patients with multiple (MS) sclerosis treated with disease-modifying therapies (DMTs) and analyzed factors predisposing for particular adverse events. Methods: We gathered data of individuals with MS treated with DMTs from 19 Polish MS Centers, who reported at least one adverse event following COVID-19 vaccination. The information was obtained by neurologists using a questionnaire. The same questionnaire was used at all MS Centers. To assess the relevance of reported adverse events, we used Fisher's exact test, t-test, and U-Menn-Whutney test. Results: A total of 1,668 patients with MS and reports of adverse events after COVID-19 vaccination were finally included in the study. Besides one case marked as "red flag", all adverse events were classified as mild. Pain at the injection site was the most common adverse event, with a greater frequency after the first dose. Pain at the injection site was significantly more frequent after the first dose among individuals with a lower disability (EDSS ≤2). The reported adverse events following immunization did not differ over sex. According to age, pain at the injection site was more common among individuals between 30 and 40 years old, only after the first vaccination dose. None of the DMTs predisposed for particular side effects. Conclusions: According to our findings, vaccination against COVID-19 among patients with MS treated with DMTs is safe. Our study can contribute to reducing hesitancy toward vaccination among patients with MS.

New insights into submicron particles impact on visibility.

The aim of the study was to analyze the impact of very fine atmospheric particles (submicron particulate matter; PM1) on visibility deterioration. Taking into consideration not only their entirely different physio-chemical properties in comparison to a well-recognized PM10 but also the origin and a growing environmental awareness of PM1, the main research problem has been solved in few steps. At first, the chemical composition of PM1 was determined in two selected urban areas in Poland. Measurements of meteorological parameters, i.e., air temperature and humidity, precipitation, atmospheric pressure, wind speed, and visibility, were also conducted. The next step of the work was the analysis of (1) seasonal changes of the concentration of PM1 and its main components, (2) the influence of chemical components of PM1 on light extinction, and (3) the influence of PM1 and humidity on visibility. Hierarchical cluster analysis, correlation matrixes and a heat map, and classification and regression tree analysis were used. The light extinction coefficient is influenced mainly by coarse mass of PM, and PM1-bound ammonium nitrate, organic matter, and by Rayleigh scattering. The less important in the light extinction coefficient shaping has PM1-bound ammonium sulfate, elemental carbon, and soil. In this way, the secondary origin PM1 components were proved to most significantly influence the visibility. The obtained results confirmed the possibility of the use of statistical agglomeration techniques to identify ranges of variation of visibility, including independent variables adopted to analyses (meteorological conditions, chemical composition of PM1, etc.).

The influence of COVID-19 pandemic lockdown on the physical activity of people with multiple sclerosis. The role of online training.

BACKGROUND: COVID-19 pandemic has affected people with multiple sclerosis (PwMS) on various levels. Pandemic lockdown influenced the access to typical measures of physical activity such as out-door training or gym exercises. METHODS: We performed a survey assessing physical activity during pandemic lockdown among PwMS treated in our MS center. The questionnaire encompassed questions regarding physical activity before and during lockdown, including the employment of online technologies. RESULTS: The survey was completed by 262 PwMS. Physical activity before lockdown was declared by 74.4% of PwMS, regular exercises were declared by 30.9% of participants. Among physically active PwMS 50.5% limited their physical activity during the COVID-19 lockdown. The decrease in physical activity was reported more frequently by PwMS with higher levels of disability, particularly declaring regular exercises before lockdown. In the opinion of 39,7% of PwMS online training could replace standard exercises, however only 19,9% of PwMS were actively looking for online training during the lockdown. The interest in online exercise was greatest in the group ≤30 years of age and EDSS ≤2. Synchronous exercises were the preferred online training, particularly among PwMS with EDSS≥4. CONCLUSION: Our findings indicate a need for systematic educational and organizational measures, promoting physical activity among PwMS and acknowledging pandemic conditions.

Safety of Vaccines against SARS-CoV-2 among Polish Patients with Multiple Sclerosis Treated with Disease-Modifying Therapies.

(1) Background: The present study aims to report the side effects of vaccination against coronavirus disease 2019 (COVID-19) among patients with multiple sclerosis (MS) who were being treated with disease-modifying therapies (DMTs) in Poland. (2) Methods: The study included 2261 patients with MS who were being treated with DMTs, and who were vaccinated against COVID-19 in 16 Polish MS centers. The data collected were demographic information, specific MS characteristics, current DMTs, type of vaccine, side effects after vaccination, time of side-effect symptom onset and resolution, applied treatment, relapse occurrence, and incidence of COVID-19 after vaccination. The results were presented using maximum likelihood estimates of the odds ratio, t-test, Pearson's chi-squared test, Fisher's exact p, and logistic regression. The statistical analyses were performed using STATA 15 software. (3) Of the 2261 sampled patients, 1862 (82.4%) were vaccinated with nucleoside-modified messenger RNA (mRNA) vaccines. Mild symptoms after immunization, often after the first dose, were reported in 70.6% of individuals. Symptoms included arm pain (47.5% after the first dose and 38.7% after the second dose), fever/chills/flu-like symptoms (17.1% after the first dose and 20.5% after the second dose), and fatigue (10.3% after the first dose and 11.3% after the second dose). Only one individual presented with severe side effects (pro-thrombotic complications) after vaccination. None of the DMTs in the presented cohort were predisposed to the development of side effects. Nine patients (0.4%) had a SARS-CoV-2 infection confirmed despite vaccination. (4) Conclusions: Vaccination against SARS-CoV-2 is safe for people with MS who are being treated with DMTs. Most adverse events following vaccination are mild and the acute relapse incidence is low.

Effect of Artificial Aging on Mechanical and Tribological Properties of CAD/CAM Composite Materials Used in Dentistry.

With easy-to-process 3D printing materials and fast production, the quality of dental services can be improved. In the conventional procedure, the dentist makes temporary crowns directly in the patient's mouth, e.g., from the most commonly used bis-acrylic composites. Temporary crowns made directly in the office without the use of CAD/CAM are often of inferior quality, which directly results in impaired hygiene, poorer masticatory mechanics, greater deposition of plaque, calculus and sediment, and may adversely affect periodontal and gum health. The mechanical strength, resistance to aging and abrasion of 3D printing materials are higher than those of the soft materials used in conventional methods. This translates into durability. The patient leaves the surgery with a restoration of higher utility quality compared to the conventional method. The objective of the paper was to determine the influence of aging in artificial saliva of AM (additive manufacturing) orthodontic composites on their functional properties. For the purpose of the study, fillings well-known worldwide were selected. These were traditional UV-curable resins (M I, M II, M III, M V) and a hybrid material based on a UV-curable resin (M VI). Samples were stored in artificial saliva at 37 ± 1 °C in a thermal chamber for 6 months. Indentation hardness, frictional tests and sliding wear measurements were conducted. A comparison between various materials was made. Descriptive statistics, degradation coefficients, H2E, Archard wear and specific wear rate were calculated. The Weibull statistical test for indentation hardness was performed and Hertzian contact stresses for the frictional association were calculated for unaged (M I, M II, M III, M V, M VI) and aged (M I AS, M II AS, M III AS, M V AS, M VI AS) samples. M I exhibited the lowest average hardness among the unaged materials, while M III AS had the lowest average hardness among the aged materials. Comparably low hardness was demonstrated by the M I AS material. The coefficient of friction values for the aged samples were found to be higher. The lowest wear value was demonstrated by the M I material. The wear resistance of most of the tested materials deteriorated after aging. The M VI AS material had the highest increase in wear. According to the results provided, not only the chemical composition and structure, but also aging have a great impact on the indentation hardness and wear resistance of the tested orthodontic materials.

Influence of Thermal Shocks on Residual Static Strength, Impact Strength and Elasticity of Polymer-Composite Materials Used in Firefighting Helmets.

The article presents results of experimental studies on mechanical properties of the polymer-composite material used in manufacturing firefighting helmets. Conducted studies included static and impact strength tests, as well as a shock absorption test of glass fiber-reinforced polyamide 66 (PA66) samples and firefighting helmets. Samples were subject to the impact of thermal shocks before or during being placed under a mechanical load. A significant influence of thermal shocks on mechanical properties of glass fiber-reinforced PA66 was shown. The decrease in strength and elastic properties after cyclic heat shocks ranged from a few to several dozen percent. The average bending strength and modulus during the 170 degree Celsius shock dropped to several dozen percent from the room temperature strength. Under these thermal conditions, the impact strength was lost, and the lateral deflection of the helmet shells increased by approximately 300%. Moreover, while forcing a thermal shock occurring during the heat load, it was noticed that the character of a composite damage changes from the elasto-brittle type into the elasto-plastic one. It was also proved that changes in mechanical and elastic properties of the material used in a helmet shell can affect the protective abilities of a helmet.

Characteristics of Particles Emitted from Waste Fires-A Construction Materials Case Study.

This study aimed to determine the relative densities of populations of particles emitted in fire experiments of selected materials through direct measurement and parametrization of size distribution as number (NSD), volume (VSD), and mass (MSD). As objects of investigation, four typical materials used in construction and furniture were chosen: pinewood (PINE), laminated particle board (LPB), polyurethane (PUR), and poly(methyl methacrylate) (PMMA). The NSD and VSD were measured using an electric low-pressure impactor, while MSD was measured by weighing filters from the impactor using a microbalance. The parametrization of distributions was made assuming that each distribution can be expressed as the sum of an arbitrary number of log-normal distributions. In all materials, except PINE, the distributions of the particles emitted in fire experiments were the sum of two log-normal distributions; in PINE, the distribution was accounted for by only one log-normal distribution. The parametrization facilitated the determination of volume and mass abundances, and therefore, the relative density. The VSDs of particles generated in PINE, LPB, and PUR fires have similar location parameters, with a median volume diameter of 0.2-0.3 µm, whereas that of particles generated during PMMA burning is 0.7 µm. To validate the presented method, we burned samples made of the four materials in similar proportions and compared the measured VSD with the VSD predicted based on the weighted sum of VSD of raw materials. The measured VSD shifted toward smaller diameters than the predicted ones due to thermal decomposition at higher temperatures.

Mechanical Properties and Strength Reliability of Impregnated Wood after High Temperature Conditions.

The paper presents the results of the research into the impact of impregnation of wood on its bending strength and elastic modulus under normal conditions and after thermal treatment and investigates its structural reliability. Pinewood, non-impregnated and pressure impregnated with a solution with SiO2 nanoparticles, was used in this research. The use of nanoparticles decreases the flammability of timber among others. Some of the tested samples were treated at 250 °C. This temperature corresponds to the boundary of the self-ignition of wood. This elevated temperature was assumed to be reached by a given speed of heating within 10 min, and then the samples were stored in these conditions for 10 and 20 min. The tests demonstrate that the bending strength of the impregnated wood was slightly improved, the impregnation did not impact the elastic modulus of the material in all such conditions, and the residual strength decreased less for the wood impregnated after being exposed to the elevated temperatures. The reliability analysis proves a positive effect of impregnation with a solution with SiO2 on the durability of wood, both after being exposed to normal and elevated temperatures. The distribution of the failure rates indicates a more intensive degradation of non-impregnated wood. The distribution of the survival function demonstrates a more probable non-destruction of impregnated wood after elevated temperature conditions.

Hardness and Wear Resistance of Dental Biomedical Nanomaterials in a Humid Environment with Non-Stationary Temperatures.

This study discusses a quantitative fatigue evaluation of polymer-ceramic composites for dental restorations, i.e., commercial material (Filtek Z550) and experimental materials Ex-nano (G), Ex-flow (G). Their evaluation is based on the following descriptors: microhardness, scratch resistance, and sliding wear. In order to reflect factors of environmental degradation conditions, thermal fatigue was simulated with a special computer-controlled device performing algorithms of thermocycling. Specimens intended for the surface strength and wear tests underwent 104 hydrothermal fatigue cycles. Thermocycling was preceded by aging, which meant immersing the specimens in artificial saliva at 37 °C for 30 days. Microhardness tests were performed with the Vickers hardness test method. The scratch test was done with a Rockwell diamond cone indenter. Sliding ball-on-disc friction tests were performed against an alumina ball in the presence of artificial saliva. A direct positive correlation was found between thermocycling fatigue and microhardness. The dominant mechanism of the wear of the experimental composites after thermocycling is the removal of fragments of the materials in the form of flakes from the friction surface (spalling). Hydrothermal fatigue is synergistic with mechanical fatigue.

Hydro-Thermal Fatigue of Polymer Matrix Composite Biomaterials.

This study discusses a quantitative fatigue evaluation of polymer-ceramic composites for dental restorations, i.e., commercial (Filtek Z550) and experimental Ex-nano (G), Ex-flow (G). Their evaluation is based on the following descriptors: mechanical strength, elastic modulus and strain work to fracture. Supposed to reflect factors of environmental degradation conditions, thermal fatigue was simulated with a special computer-controlled device performing algorithms of thermocycling. The specimens intended for the strength test underwent 104 hydro-thermal fatigue cycles. This procedure of thermocycling was preceded by aging, which meant immersing the specimens in artificial saliva at 37 °C for 30 days. The strength tests after aging only and after aging and thermocycles were performed in line with the three-point flexural strength (TFS) test, specified in ISO 4049, and the biaxial flexural strength (BFS) test, specifically piston-on-three-ball in accordance with ISO 6872. Based on the results, it can be stated that composites with higher volume content of inorganic particles after aging only show higher strength than materials with lower filler particle content. For example, the average flexural bending strength of the Ex-flow (G) composite was about 45% lower than the value obtained for the Ex-nano (G) material. The residual strength after thermocycles is significantly lower for the experimental composites, whereas a smaller decrease in strength is recorded for the commercial composites. Decreases in strength were about 4% (Filtek Z550), 43% (Ex-nano (G)), and 29% (Ex-flow (G)) for the BFS test; and about 17% (Filtek Z550), 55% (Ex-nano (G)), 60% (Ex-flow (G)) for the TFS test. The elastic modulus of the experimental composites after only aging is higher (about 42%) than that of the commercial composite, but the elastic modulus of the commercial composite increases significantly after thermocycling. A descriptor known as strain work to fracture turns out to be a good descriptor for evaluating the hydro-thermal fatigue of the tested polymer-ceramic composites.

The Effect of Thermocycling on Surface Layer Properties of Light Cured Polymer Matrix Ceramic Composites (PMCCs) Used in Sliding Friction Pair.

This paper discusses the problem of thermocycling effect of light-curing polymer-ceramic composites. Cyclic thermal shocks were simulated in laboratory conditions. As a rule, these loads were supposed to reproduce the actual conditions of biomaterials exploitation. Periodically variable stresses occurring in dental restorations are associated with the wear of cold and hot foods and beverages. They lead to changes in the properties of composites, including the properties of the surface layer. The aim of the work was to assess the impact of cyclic hydrothermal interactions on the properties of the surface layer of composites relevant to the operational quality. Two commercial materials manufactured by the world's leading producer (3M ESPE)-Filtek Z550, Filtek Flow and two experimental, micro-hybrid and flow type composites marked Ex-mhyb(P) and Ex-flow(P), respectively. All tests were carried out before and after hydro-thermal cycles (flowing water thermocycling). Micro-hardness test using the Vickers method, indentation hardness, and resistance to tribological wear in a ball-disc system in sliding friction conditions were performed. In addition, observations of the surface layer of composites on the SEM (scanning electron microscope) were carried out. It was noticed that semi-liquid composites, containing a smaller amount of filler, retain higher stability of mechanical and tribological properties of the surface layer under cyclic hydro-thermal loads. Coefficient of friction of samples after hydro-thermal cycles increased for micro-hybrid materials and Filtek Flow (FFlow) composite. In the case of Ex-flow(P) material, the coefficient of friction decreased. The microhardness of composites also changed, the variability of this size depended on the type of material. Composites with a higher content of filler particles were characterized by greater variability of microhardness under the influence of thermocycles. The resistance to tribological wear also changed in a similar way. Composites containing higher volume fraction of inorganic filler showed higher tribological wear after thermocycling. The wear resistance of flow composites changed to a lesser extent, after thermocycling increased. The paper also showed that, in real kinematic nodes, the surface layer of light-curing ceramic-polymer composites is exposed to significant non-tribological (erosive, thermal, and chemical) defects that synergize with tribological ones. In slip pairs loaded dynamically, under mixed friction conditions, tribological wear of PMCCs (polymer matrix ceramic composites) is manifested by spalling (spalling of the material flakes, in particular the polymer phase) and pitting (crushing wear caused by wear products, in particular large filler particles or clusters, previously adhesively extracted).

Real-world effectiveness of fingolimod in Polish group of patients with relapsing-remitting multiple sclerosis.

OBJECTIVES: Fingolimod is indicated for the treatment of relapsing-remitting multiple sclerosis (RRMS) patients with highly aggressive disease characterized by frequent relapses and active magnetic resonance imaging. Its efficacy has been demonstrated in three large phase III trials, used in the regulatory submissions throughout the world. Fingolimod in licensed in Europe since 2011 but with a growing number of disease-modifying drugs (DMD) becoming available for RRMS, it is important to gather real-world evidence data regarding long-term effectiveness in treated patients with MS. The aim of this study was to assess fingolimod effectiveness in a real life Polish group of RRMS patients receiving fingolimod as second line treatment. PATIENTS AND METHODS: The observational study with retrospective data collection was performed at 13 sites that were asked to document eligible patients in consecutive chronological order to avoid selection bias. Demographic and clinical data from 253 adult patients with RRMS treated with fingolimod were analyzed. RESULTS: Mean treatment time with fingolimod was 42 months. Relapses reduction during 3 years treatment period was observed (2.0 v 0.2) and majority of patients were free of relapses. Mean EDSS score was stable during the time of observation. The proportion of patients who were free from any clinical disease activity, i.e. without relapses and disability progression, was over 70%. During the first and second year of observation significant reduction of new MRI lesions was observed. CONCLUSION: In the Polish group of patients with RRMS treated with fingolimod, the majority of them showed freedom from relapses, disability progression and reduction of new MRI lesions. Switching from injectable immunomodulatory drugs to fingolimod is associated with fewer relapses and lower disability progression.

Influence of fibre reinforcement on selected mechanical properties of dental composites.

PURPOSE: For splinting or designing adhesive bridges, reconstructive composite structures with increased mechanical properties owing to embedded reinforcement fibres are used. The aim of this article was to determine the influence of glass and aramid fibres on the mechanical strength of composites reinforced with these fibres. METHODS: Two polymer-ceramic microhybrid materials: Boston and Herculite were tested. Three types of reinforcement fibres were used: aramid (Podwiazka) with a single layer weave, a single layer weave glass fibre (FSO) and triple layer weave glass fibre (FSO evo). Tests were conducted in accordance with the requirements of ISO 4049:2009. The following material types were chosen for research: Boston, Boston + Podwiazka, Herculite, Herculite + Podwiazka, Herculite + FSO and Herculite + FSO evo. The scope of research included: flexural strength B, bending modulus of elasticity εB and work to failure of the reinforced composite Wfb. Additionally, microscopic observations of fracture occurring in samples were made. RESULTS: In comparison: the Herculite (97.7 MPa) type with the Herculite + FSO evo (177.5 MPa) type was characterized by the highest strength. Fibre reinforcement resulted in decreasing the elasticity modulus: Herculite + reinforcement (6.86 GPa; 6.33 GPa; 6.11 GPa) in comparison with the Herculite (9.84 GPa) and respectively Boston + reinforcement (10.08 GPa) as compared with the Boston (11.81 GPa). CONCLUSIONS: Using glass fibres increases flexural strength of the test composites. Using aramid fibres does not change their strength. The elasticity modulus of the reinforced reconstructive structures decreases after application of either type of fibres. However, their resistance to the crack initiation increases.

[Neurological symptoms and syndromes in municipal transport drivers]. / Objawy i zespoly neurologiczne u kierowców pojazdów komunikacji miejskiej.

BACKGROUND: The way the municipal transport drivers perform their job contributes to varied burdens linked with the body posture at work, stress, shift work, vibration, noise and exposure to chemical agents. The aim of the study was to assess the condition of the nervous system (NS) in municipal transport drivers. MATERIAL AND METHODS: The study covered 42 men, aged 43.4 years (standard deviation (SD): 8.3), employed as bus drivers in the municipal transport enterprise. The duration of employment was 11.8 years on average (SD: 8.6). The condition of the nervous system was assessed on the basis of clinical neurological examinations. RESULTS: Chronic lumbosacral syndrome was found in 54.8% of the subjects. A significant relationship between the incidence of lumbosacral syndrome and the duration of employment (p=0.032) was observed; significantly higher in drivers employed for 11-15 years (90.9%) in comparison to the remaining groups. Nervous system functional disorders were characterized by the increased emotional irritability (47.6%), sleep disorders manifested by excessive sleepiness (33.3%) or insomnia (28.6%) and headaches (3%), mostly tension headaches. Excessive daytime sleepiness was significantly age-dependent (p=0.038). CONCLUSIONS: The evidenced NS disorders indicate the need to undertake preventive measures tailored for the occupational group of bus drivers.

Translocation of positively and negatively charged polystyrene nanoparticles in an in vitro placental model.

To obtain insight in translocation of nanoparticles across the placental barrier, translocation was studied for one positively and two negatively charged polystyrene nanoparticles (PS-NPs) of similar size in an in vitro model. The model consisted of BeWo b30 cells, derived from a human choriocarcinoma grown on a transwell insert forming a cell layer that separates an apical from a basolateral compartment. PS-NPs were characterized with respect to size, surface charge, morphology and protein corona. Translocation of PS-NPs was not related to PS-NP charge. Two PS-NPs were translocated across the BeWo transwell model to a lower extent than amoxicillin, a model compound known to be translocated over the placental barrier to only a limited extent, whereas one PS-NP showed a slightly higher translocation. Studies on the effect of transporter inhibitors on the translocation of the PS-NPs indicated that their translocation was not mediated by known transporters and mainly dependent on passive diffusion. It is concluded that the BeWo b30 model can be used as an efficient method to get an initial qualitative impression about the capacity of NPs to translocate across the placental barrier and set priorities in further in vivo studies on translocation of NPs to the fetus.

Bioavailability and biodistribution of differently charged polystyrene nanoparticles upon oral exposure in rats.

The likelihood of oral exposure to nanoparticles (NPs) is increasing, and it is necessary to evaluate the oral bioavailability of NPs. In vitro approaches could help reducing animal studies, but validation against in vivo studies is essential. Previously, we assessed the translocation of 50 nm polystyrene NPs of different charges (neutral, positive and negative) using a Caco-2/HT29-MTX in vitro intestinal translocation model. The NPs translocated in a surface charge-dependent manner. The present study aimed to validate this in vitro intestinal model by an in vivo study. For this, rats were orally exposed to a single dose of these polystyrene NPs and the uptake in organs was determined. A negatively charged NP was taken up more than other NPs, with the highest amounts in kidney (37.4 µg/g tissue), heart (52.8 µg/g tissue), stomach wall (98.3 µg/g tissue) and small intestinal wall (94.4 µg/g tissue). This partly confirms our in vitro findings, where the same NPs translocated to the highest extent. The estimated bioavailability of different types of NPs ranged from 0.2 to 1.7 % in vivo, which was much lower than in vitro (1.6-12.3 %). Therefore, the integrated in vitro model cannot be used for a direct prediction of the bioavailability of orally administered NPs. However, the model can be used for prioritizing NPs before further in vivo testing for risk assessment.

In vitro gastrointestinal digestion increases the translocation of polystyrene nanoparticles in an in vitro intestinal co-culture model.

The conditions of the gastrointestinal tract may change the physicochemical properties of nanoparticles (NPs) and therewith the bioavailability of orally taken NPs. Therefore, we assessed the impact of in vitro gastrointestinal digestion on the protein corona of polystyrene NPs (PS-NPs) and their subsequent translocation across an in vitro intestinal barrier. A co-culture of intestinal Caco-2 and HT29-MTX cells was exposed to 50 nm PS-NPs of different charges (positive and negative) in two forms: pristine and digested in an in vitro gastrointestinal digestion model. In vitro digestion significantly increased the translocation of all, except the "neutral", PS-NPs. Upon in vitro digestion, translocation was 4-fold higher for positively charged NPs and 80- and 1.7-fold higher for two types of negatively charged NPs. Digestion significantly reduced the amount of protein in the corona of three out of four types of NPs. This reduction of proteins was 4.8-fold for "neutral", 3.5-fold for positively charged and 1.8-fold for one type of negatively charged PS-NPs. In vitro digestion also affected the composition of the protein corona of PS-NPs by decreasing the presence of higher molecular weight proteins and shifting the protein content of the corona to low molecular weight proteins. These findings are the first to report that in vitro gastrointestinal digestion significantly affects the protein corona and significantly increases the in vitro translocation of differently charged PS-NPs. These findings stress the importance of including the in vitro digestion in future in vitro intestinal translocation screening studies for risk assessment of orally taken NPs.

Translocation of differently sized and charged polystyrene nanoparticles in in vitro intestinal cell models of increasing complexity.

Intestinal translocation is a key factor for determining bioavailability of nanoparticles (NPs) after oral uptake. Therefore, we evaluated three in vitro intestinal cell models of increasing complexity which might affect the translocation of NPs: a mono-culture (Caco-2 cells), a co-culture with mucus secreting HT29-MTX cells and a tri-culture with M-cells. Cell models were exposed to well characterized differently sized (50 and 100 nm) and charged (neutral, positively and negatively) polystyrene NPs. In addition, two types of negatively charged NPs with different surface chemistries were used. Size strongly affected the translocation of NPs, ranging up to 7.8% for the 50 nm NPs and 0.8% for the 100 nm NPs. Surface charge of NPs affected the translocation, however, surface chemistry seems more important, as the two types of negatively charged 50 nm NPs had an over 30-fold difference in translocation. Compared with the Caco-2 mono-culture, presence of mucus significantly reduced the translocation of neutral 50 nm NPs, but significantly increased the translocation of one type of negatively charged NPs. Incorporation of M-cells shifted the translocation rates for both NPs closer to those in the mono-culture model. The relative pattern of NP translocation in all three models was similar, but the absolute amounts of translocated NPs differed per model. We conclude that for comparing the relative translocation of different NPs, using one intestinal model is sufficient. To choose the most representative model for risk assessment, in vivo experiments are now needed to determine the in vivo translocation rates of the used NPs.