RESUMEN
High-entropy oxides (HEOs) are promising anode materials for lithium-ion batteries (LIBs), owing to their stable crystal structure, superionic conductivity, and high capacity. In this study, the (Cr, Mn, Fe, Co, and Ni)3O4 HEO via solid-state reaction is prepared. To improve the synthetic efficiency, it is necessary to understand the formation mechanism. Therefore, a high-resolution transmission electron microscopy (HRTEM) is used to record information during calcination at increasing temperature. The overall formation process included MnO2 and NiO aggregation at 500 °C, followed by (Mn, and Ni)3O4 combined with Co3O4 at 600 °C to form (Mn, Co, and Ni)3O4. At higher temperatures, Fe2O3 and Cr2O3 sequentially combined with (Mn, Co, and Ni)3O4 and formed the (Cr, Mn, Fe, Co, Ni)3O4 at 900 °C. In addition, the valence-state-changing mechanisms and ion arrangements of (Cr, Mn, Fe, Co, and Ni)3O4 are determined using electron energy loss spectroscopy (EELS) and extended X-ray absorption fine structure (EXAFS). This study successfully revealed the formation of HEO at atomic scale. The results provide valuable insights for improving the manufacturing process of (Cr, Mn, Fe, Co, and Ni)3O4 HEOs, which is expected to play a vital role in the development of anode materials for next-generation LIBs.
RESUMEN
Silicon CMOS-based computing-in-memory encounters design and power challenges, especially in logic-in-memory scenarios requiring nonvolatility and reconfigurability. Here, we report a universal design for nonvolatile reconfigurable devices featuring a 2D/3D heterointegrated configuration. By leveraging the photo-controlled charge trapping/detrapping process and the partially top-gated energy band landscape, the van der Waals heterostacking achieves polarity storage and logic reconfigurable characteristics, respectively. Precise polarity tunability, logic nonvolatility, robustness against high temperature (at 85°C), and near-ideal subthreshold swing (80 mV dec-1) can be done. A comprehensive investigation of dynamic charge fluctuations provides a holistic understanding of the origins of nonvolatile reconfigurability (a trap level of 1013 cm-2 eV-1). Furthermore, we cascade such nonvolatile reconfigurable units into a monolithic circuit layer to demonstrate logic-in-memory computing possibilities, such as high-gain (65 at Vdd = 0.5 V) logic gates. This work provides an innovative 3D heterointegration prototype for future computing-in-memory hardware.
RESUMEN
Recently, all-solid-state sodium batteries (Na-ASSBs) have received increased interest owing to their high safety and potential of high energy density. The potential of Na-ASSBs based on sodium superionic conductor (NASICON)-structured Na3 V2 (PO4 )3 (Na3 VP) cathodes have been proven by their high capacity and a long cycling stability closely related to the microstructural evolution. However, the detailed kinetics of the electrochemical processes in the cathodes is still unclear. In this work, the sodiation/desodiation process of Na3 VP is first investigated using in situ high-resolution transmission electron microscopy (HRTEM). The intermediate Na2 V2 (PO4 )3 (Na2 VP) phase with the P21 /c space group, which would be inhibited by constant electron beam irradiation, is observed at the atomic scale. With the calculated volume change and the electrode-electrolyte interface after cycling, it can be concluded that the Na2 VP phase reduces the lattice mismatch between Na3 VP and NaV2 (PO4 )3 (NaVP), preventing structural collapse. Based on the density functional theory calculation (DFT), the Na+ ion migrates more rapidly in the Na2 VP structure, which facilitates the desodiation and sodiation processes. The formation of Na2 VP phase lowers the formation energy of NaVP. This study demonstrates the dynamic evolution of the Na3 VP structure, paving the way for an in-depth understanding of electrode materials for energy-storage applications.
RESUMEN
Quasi van der Waals epitaxy is an approach to constructing the combination of 2D and 3D materials. Here, we quantify and discuss the 2D/3D interface structure and the corresponding features in metal/muscovite systems. High-resolution scanning transmission electron microscopy reveals the atomic arrangement at the interface. The theoretical results explain the formation mechanism and predict the mechanical robustness of these metal/muscovite quasi van der Waals epitaxies. The evidence of superior interface quality is delivered according to the outstanding performance of the designed systems in both retention (>105 s) and cycling tests (>105 cycles) through electromechanical measurements. With high-temperature X-ray reciprocal space mapping, the unique anisotropy of thermal expansion is discovered and predicted to sustain the thermal stress with a sizable thermal actuation. A maximum bending curvature of 264 m-1 at 243 °C can be obtained in the silver/muscovite heteroepitaxy. The electrothermal and photothermal methods show a fast response to thermal stress and demonstrate the interface robustness.
RESUMEN
Usually, most studies focus on toxic gas and photosensors by using electrospinning and metal oxide polycrystalline SnO2 nanofibers (PNFs), while fewer studies discuss cell-material interactions and photoelectric effect. In this work, the controllable surface morphology and oxygen defect (VO) structure properties were provided to show the opportunity of metal oxide PNFs to convert photoenergy into bio-energy for bio-material applications. Using the photobiomodulation effect of defect-rich polycrystalline SnO2 nanofibers (PNFs) is the main idea to modulate the cell-material interactions, such as adhesion, growth direction, and reactive oxygen species (ROS) density. The VO structures, including out-of-plane oxygen defects (op-VO), bridge oxygen defects (b-VO), and in-plane oxygen defects (ip-VO), were studied using synchrotron analysis to investigate the electron transfer between the VO structures and conduction bands. These intragrain VO structures can be treated as generation-recombination centers, which can convert various photoenergies (365-520 nm) into different current levels that form distinct surface potential levels; this is referred to as the photoelectric effect. PNF conductivity was enhanced 53.6-fold by enlarging the grain size (410 nm2) by increasing the annealing temperature, which can improve the photoelectric effect. In vitro removal of reactive oxygen species (ROS) can be achieved by using the photoelectric effect of PNFs. Also, the viability and shape of human bone marrow mesenchymal stem cells (hMSCs-BM) were also influenced significantly by the photobiomodulation effect. The cell damage and survival rate can be prevented and enhanced by using PNFs; metal oxide nanofibers are no longer only environmental sensors but can also be a bio-material to convert the photoenergy into bio-energy for biomedical science applications.
RESUMEN
The application of high-entropy oxide (HEO) has attracted significant attention in recent years owing to their unique structural characteristics, such as excellent electrochemical properties and long-term cycling stability. However, the application of resistive random-access memory (RRAM) has not been extensively studied, and the switching mechanism of HEO-based RRAM has yet to be thoroughly investigated. In this study, HEO (Cr, Mn, Fe, Co, Ni)3 O4 with a spinel structure is epitaxially grown on a Nb:STO conductive substrate, and Pt metal is deposited as the top electrode. After the resistive-switching operation, some regions of the spinel structure are transformed into a rock-salt structure and analyzed using advanced transmission electron microscopy and scanning transmission electron microscopy. From the results of X-ray photoelectron spectroscopy and electron energy loss spectroscopy, only specific elements would change their valence state, which results in excellent resistive-switching properties with a high on/off ratio on the order of 105 , outstanding endurance (>4550 cycles), long retention time (>104 s), and high stability, which suggests that HEO is a promising RRAM material.
RESUMEN
INTRODUCTION: The potential association between severe postoperative complications (SPC) and the oncological outcomes of esophageal squamous cell carcinoma (ESCC) patients according to the different Naples Prognostic Score (NPS) of the inflammatory nutritional status after minimally invasive esophagectomy (MIE) is unclear. METHODS: Kaplan-Meier survival analysis was used to evaluate overall survival (OS) and disease-free survival (DFS) between with or without SPC (Clavien-Dindo grade ≥ III) in low NPS status (NPS = 0 or 1) and high NPS status (NPS = 2 or 3 or 4) patients. Cox multivariable analysis was carried out to analyze the various independent factors of OS and DFS, and a nomogram based on SPC was established. RESULTS: A total of 20.7% (125/604) ESCC patients developed SPC after MIE. Patients with SPC exhibited poor 5-year OS and DFS compared to those without SPC (all P < 0.001). Further analysis revealed that SPC significantly reduced OS and DFS in patients with high NPS status (all P < 0.001) but had little effect on the prognosis of patients with low NPS status (all P > 0.05). Multivariable Cox analysis revealed that SPC could be an independent influence indicator for OS and DFS in patients with high NPS status. Therefore, a novel nomogram combining SPC and tumor-node-metastasis (TNM) staging has been developed, which was found to be relatively more accurate in predicting OS and DFS than TNM staging alone. CONCLUSION: Severe complications can adversely affect the long-term oncological outcome of ESCC patients with high systemic inflammatory response and malnutrition after MIE.
Asunto(s)
Neoplasias Esofágicas , Carcinoma de Células Escamosas de Esófago , Humanos , Carcinoma de Células Escamosas de Esófago/cirugía , Neoplasias Esofágicas/patología , Estado Nutricional , Esofagectomía/efectos adversos , Pronóstico , Complicaciones Posoperatorias/epidemiología , Complicaciones Posoperatorias/etiología , Estudios RetrospectivosRESUMEN
Li7 La3 Zr2 O12 (LLZO)-based all-solid-state Li batteries (SSLBs) are very attractive next-generation energy storage devices owing to their potential for achieving enhanced safety and improved energy density. However, the rigid nature of the ceramics challenges the SSLB fabrication and the afterward interfacial stability during electrochemical cycling. Here, a promising LLZO-based SSLB with a high areal capacity and stable cycle performance over 100 cycles is demonstrated. In operando transmission electron microscopy (TEM) is used for successfully demonstrating and investigating the delithiation/lithiation process and understanding the capacity degradation mechanism of the SSLB on an atomic scale. Other than the interfacial delamination between LLZO and LiCoO2 (LCO) owing to the stress evolvement during electrochemical cycling, oxygen deficiency of LCO not only causes microcrack formation in LCO but also partially decomposes LCO into metallic Co and is suggested to contribute to the capacity degradation based on the atomic-scale insights. When discharging the SSLB to a voltage of ≈1.2 versus Li/Li+ , severe capacity fading from the irreversible decomposition of LCO into metallic Co and Li2 O is observed under in operando TEM. These observations reveal the capacity degradation mechanisms of the LLZO-based SSLB, which provides important information for future LLZO-based SSLB developments.
RESUMEN
Recently, perovskite (PV) oxides with ABO3 structures have attracted considerable interest from scientists owing to their functionality. In this study, CaFeOx is introduced to reveal the resistive switching properties and mechanism of oxygen vacancy transition in PV and brownmillerite (BM) structures. BM-CaFeO2.5 is grown on an Nb-STO conductive substrate epitaxially. CaFeOx exhibits excellent endurance and reliability. In addition, the CaFeOx also demonstrates an electroforming-free characteristic and multilevel resistance properties. To construct the switching mechanism, high-resolution transmission electron microscopy is used to observe the topotactic phase change in CaFeOx . In addition, scanning TEM and electron energy loss spectroscopy show the structural evolution and valence state variation of CaFeOx after the switching behavior. This study not only reveals the switching mechanism of CaFeOx , but also provides a PV oxide option for the dielectric material in resistive random-access memory (RRAM) devices.
RESUMEN
Surface diffusion is intimately correlated with crystal orientation and surface structure. Fast surface diffusion accelerates phase transformation and structural evolution of materials. Here, through in situ transmission electron microscopy observation, we show that a copper nanowire with dense nanoscale coherent twin-boundary (CTB) defects evolves into a zigzag configuration under electric-current driven surface diffusion. The hindrance at the CTB-intercepted concave triple junctions decreases the effective surface diffusivity by almost 1 order of magnitude. The energy barriers for atomic migration at the concave junctions and different faceted surfaces are computed using density functional theory. We proposed that such a stable zigzag surface is shaped not only by the high-diffusivity facets but also by the stalled atomic diffusion at the concave junctions. This finding provides a defect-engineering route to develop robust interconnect materials against electromigration-induced failures for nanoelectronic devices.
RESUMEN
In this study, facile salt-assisted chemical vapor deposition (CVD) was used to synthesize ultrathin non-van der Waals chromium sulfide (Cr2S3) with a thickness of â¼1.9 nm. The structural transformation of as-grown Cr2S3 was studied using advanced in situ heating techniques combined with transmission electron microscopy (TEM). Two-dimensional (2D) and quasi-one-dimensional (1D) samples were fabricated to investigate the connection between specific planes and the dynamic behavior of the structural variation. The rearrangement of atoms during the phase transition was driven by the loss of sulfur atoms at elevated temperatures, resulting in increased free energy. A decrease in the ratio of the (001) plane led to an overall increase in surface energy, thus lowering the critical phase transition temperature. Our study provides detailed insight into the mechanism of structural transformation and the critical factors governing transition temperature, thus paving the way for future studies on intriguing Cr-S compounds.
RESUMEN
Contact engineering of two-dimensional semiconductors is a central issue for performance improvement of micro-/nanodevices based on these materials. Unfortunately, the various methods proposed to improve the Schottky barrier height normally require the use of high temperatures, chemical dopants, or complex processes. This work demonstrates that diffused electron beam energy (DEBE) treatment can simultaneously reduce the Schottky barrier height and enable the direct writing of electrical circuitry on van der Waals semiconductors. The electron beam energy projected into the region outside the electrode diffuses into the main channel, producing selective-area n-type doping in a layered MoTe2 (or MoS2) field-effect transistor. As a result, the Schottky barrier height at the interface between the electrode and the DEBE-treated MoTe2 channel is as low as 12 meV. Additionally, because selective-area doping is possible, DEBE can allow the formation of both n- and p-type doped channels within the same atomic plane, which enables the creation of a nonvolatile and homogeneous MoTe2 p-n rectifier with an ideality factor of 1.1 and a rectification ratio of 1.3 × 103. These results indicate that the DEBE method is a simple, efficient, mask-free, and chemical dopant-free approach to selective-area doping for the development of van der Waals electronics with excellent device performances.
RESUMEN
Van der Waals (vdW) heterostructures-in which layered materials are purposely selected to assemble with each other-allow unusual properties and different phenomena to be combined and multifunctional electronics to be created, opening a new chapter for the spread of internet-of-things applications. Here, an O2 -ultrasensitive MoTe2 material and an O2 -insensitive SnS2 material are integrated to form a vdW heterostructure, allowing the realization of charge-polarity control for multioperation-mode transistors through a simple and effective rapid thermal annealing strategy under dry-air and vacuum conditions. The charge-polarity control (i.e., doping and de-doping processes), which arises owing to the interaction between O2 adsorption/desorption and tellurium defects at the MoTe2 surface, means that the MoTe2 /SnS2 heterostructure transistors can reversibly change between unipolar, ambipolar, and anti-ambipolar transfer characteristics. Based on the dynamic control of the charge-polarity properties, an inverter, output polarity controllable amplifier, p-n diode, and ternary-state logics (NMIN and NMAX gates) are demonstrated, which inspire the development of reversibly multifunctional devices and indicates the potential of 2D materials.
RESUMEN
2D materials have great potential for not only device scaling but also various applications. To prompt the development of 2D electronics and optoelectronics, a better understanding of the limitation of materials is essential. Material failure caused by bias can lead to variations in device behavior and even electrical breakdown. In this study, the structural evolution of monolayer MoS2 with high bias is revealed via in situ transmission electron microscopy at the atomic scale. The biasing process is recorded and studied with the aid of aberration-corrected scanning transmission electron microscopy. The effects of electron beam irradiation and biasing are also discussed through the combination of experiments and theory. It is found that the Mo nanoclusters result from disintegration of MoS2 and sulfur depletion, which are induced by Joule heating. The thermal stress can also damage the MoS2 layer and form long cracks in both in situ and ex situ biasing cases. Investigation of the results obtained with different applied voltages helps to further verify the mechanism of evolution and provide a comprehensive study of the function of biasing.
RESUMEN
The exine capsules of pollen particles exhibit a variety of characteristic surface morphologies that promote their cell interactions; their use as antigen carriers for vaccination has been proposed. However, the allergy-causing substances in pollen particles may not all be removed, even by vigorous chemical treatments. To resolve this issue, this work develops systemic approaches for synthesizing pollen-mimetic metal-organic frameworks (MOFs), which comprise aluminum (Al) ions and an organic linker (2-aminoterephthalic acid), with tunable spike-like nanostructures on their surfaces. The as-synthesized MOFs act not only as a delivery vehicle that carries a model antigen (ovalbumin, OVA) but also as an adjuvant (Al). Scanning and transmission electron microscopies images reveal that the aspect ratio of the nanospikes that are grown on the MOFs can be controlled. A higher aspect ratio of the nanospikes on the MOFs is associated with greater cell attachment and faster and more efficient phagocytosis in cells, which results in greater expressions of pro-inflammatory cytokines. Consequently, a more robust immune response against the antigen of interest is elicited. These findings have broad implications for the rational design of the future antigen/adjuvant-presenting particles for vaccination.
Asunto(s)
Estructuras Metalorgánicas , Nanoestructuras , Comunicación Celular , Inmunidad Humoral , Ovalbúmina , PolenRESUMEN
The development of SnO2 and TiO2 polycrystalline nanofiber devices (PNFDs) has been widely researched as a method of protecting humans from household air pollution. PNFDs have three significant advantages. The nanofibers before the annealing process are polymer-rich materials, which can be used as particulate material (PM) filters. The multiporous nanofibers fabricated by the annealing process have numerous defects that can serve as generation-recombination centers for electron-hole pairs, enabling the PNFDs to serve as multiple-wavelength light (from 365 to 940 nm) detectors. Lastly, the numerous surface/interface defects can drastically enhance the toxic gas detection ability. The toxic gas detection range of PNFDs for CO(g) and NO(g) is from 400 to 50 ppm and 400 to 50 ppb, respectively. Quick response times and recovery properties are key parameters for commercial applications. The recovery time of NO(g) detection can be improved from 1 ks to 40 s and the PNFD operating temperature lowered to 50 °C. These results indicate that SnO2 and TiO2 PNFDs have good potential for commercialization and use as toxic gas and photon sensors in daily lives.
RESUMEN
Two-dimensional (2D) materials and van der Waals heterostructures with atomic-scale thickness provide enormous potential for advanced science and technology. However, insufficient knowledge of compatible synthesis impedes wafer-scale production. PdSe2 and Pd2Se3 are two of the noble transition-metal chalcogenides with excellent physical properties that have recently emerged as promising materials for electronics, optoelectronics, catalyst, and sensors. This research presents a feasible approach to synthesize PdSe2 and Pd2Se3 with inherently asymmetric structure on honeycomb lattice 2D monolayer substrates of graphene and MoS2. We directly deposit a molecular transition-metal precursor complex on the surface of the 2D substrates, followed by low-temperature selenization by chemical vapor flow. Parameter control leads to tuning of the material from monolayer nanocrystals with Pd2Se3 phase, to continuous few-layer PdSe2 films. Annular dark-field scanning transmission electron microscopy (ADF-STEM) reveals the structure, phase variations, and heteroepitaxy at the atomic level. PdSe2 with unconventional interlayer stacking shifts appeared as the kinetic product, whereas the bilayer PdSe2 and monolayer Pd2Se3 are the thermodynamic product. The epitaxial alignment of interlayer rotation and translation between the PdSe2 and underlying 2D substrate was also revealed by ADF-STEM. These results offer both nanoscale and atomic-level insights into direct growth of van der Waals heterostructures, as well as an innovative method for 2D synthesis by predetermined nucleation.
RESUMEN
Layered MoS2 is a prospective candidate for use in energy harvesting, valleytronics, and nanoelectronics. Its properties strongly related to its stacking configuration and the number of layers. Due to its atomically thin nature, understanding the atomic-level and structural modifications of 2D transition metal dichalcogenides is still underdeveloped, particularly the spatial control and selective precision. Therefore, the development of nanofabrication techniques is essential. Here, an atomic-scale approach used to sculpt 2D few-layer MoS2 into lateral heterojunctions via in situ scanning/transmission electron microscopy (STEM/TEM) is developed. The dynamic evolution is tracked using ultrafast and high-resolution filming equipment. The assembly behaviors inherent to few-layer 2D-materials are observed during the process and included the following: scrolling, folding, etching, and restructuring. Atomic resolution STEM is employed to identify the layer variation and stacking sequence for this new 2D-architecture. Subsequent energy-dispersive X-ray spectroscopy and electron energy loss spectroscopy analyses are performed to corroborate the elemental distribution. This sculpting technique that is established allows for the formation of sub-10 nm features, produces diverse nanostructures, and preserves the crystallinity of the material. The lateral heterointerfaces created in this study also pave the way for the design of quantum-relevant geometries, flexible optoelectronics, and energy storage devices.
RESUMEN
Crystalline Mo5O14 exhibits distinctive structural features such as tunnel structure and pseudolamellar arrangement according to the ideal model. However, the spatial resolution of the conventional technique of transmission electron microscopy (TEM) is insufficient to distinguish the actual positions of atoms. In this work, we aimed to systematically analyze and identify the Mo5O14 nanowires fabricated by the chemical vapor deposition (CVD) process. Utilizing high-angle annular dark-field (HAADF), annular bright-field (ABF), and enhanced annular bright-field (E-ABF) within the scanning transmission electron microscope (STEM) mode reveals the structural features at the atomic scale. In addition, the ultrahigh resolution images have confirmed the crystallographic insights in [001] growth direction for the Mo5O14 nanowires with a tunnel structure throughout the nanowire. The cross-sectional images show the unique close-packed plane and atomic arrangement with a network of MoO6 octahedra and MoO7 pentagonal bipyramids. These results are consistent with the theoretical atomic arrangement, supporting the realization of Mo5O14-type catalysts used in the selective oxidation process and battery applications.
RESUMEN
Electron beam (e-beam) has been developed for nanomaterial observation and moreover to induce structural evolutions in atomic scale. In this work, we demonstrate the deoxidation of cuprous oxide (Cu2O) and the formation of an atomically flat surface on a Cu nanowire by e-beam irradiation. To develop e-beam irradiation applications, the relation between e-beam radiation and the atomic surface is significant. Through the density functional theory simulation of atomic sputtering, an obvious disparity in the sputtering threshold has been found under different structural conditions, which leads to different structural evolutions. Both surface deoxidation and atomic surface flattening reactions have been identified as self-limiting and irreversible processes via in situ transmission electron microscope observation. Under e-beam irradiation, the dynamic mechanism of atomic surface flattening is driven by the convergence of total surface energy and confirmed by climbing-image nudged elastic band (ci-NEB) calculations. With precise control, e-beam irradiation reveals enormous potentials in atomic surface engineering.