Large Orientation Angle Buried Substrate Enables Efficient Flexible Perovskite Solar Cells and Modules.

Flexible perovskite solar cells (f-PSCs) have emerged as potential candidates for specific mechanical applications owing to their high foldability, efficiency, and portability. However, the power conversion efficiency (PCE) of f-PSC remains limited by the inferior contact between perovskite and flexible buried substrate. Here, an asymmetric π-extended self-assembled monolayer (SAM) (4-(9H-dibenzo[a,c]carbazol-9-yl)butyl)phosphonic acid (A-4PADCB) is reported as a buried substrate for efficient inverted f-PSCs. Employing this design strategy, A-4PADCB exhibits a significant orientation angle away from the surface normal, homogenizing the distribution of contact potentials. This enhancement improves the SAM/perovskite interface quality, controlling the growth of favorable perovskite films with low defect density and slight tensile stress. Integration of A-4PADCB into small-area f-PSCs and large-area flexible perovskite solar modules with an aperture area of 20.84 cm2 achieves impressive PCEs of up to 25.05% and 20.64% (certified 19.51%), respectively. Moreover, these optimized A-4PADCB-based f-PSCs possess enhanced light, thermal, and mechanical stability. This research paves a promising avenue toward the design of SAM-buried substrates with a large orientation angle, regulating perovskite growth, and promoting the commercialization of large-area flexible perovskite photovoltaics.

Correction: Preventing lead leakage in perovskite solar cells and modules with a low-cost and stable chemisorption coating.

Correction for 'Preventing lead leakage in perovskite solar cells and modules with a low-cost and stable chemisorption coating' by Zongxu Zhang et al., Mater. Horiz., 2024, 11, 2449-2456, https://doi.org/10.1039/D4MH00033A.

Alkyl Chains Tune Molecular Orientations to Enable Dual Passivation in Inverted Perovskite Solar Cells.

Nonradiative recombination losses occurring at the interface pose a significant obstacle to achieve high-efficiency perovskite solar cells (PSCs), particularly in inverted PSCs. Passivating surface defects using molecules with different functional groups represents one of the key strategies for enhancing PSCs efficiency. However, a lack of insight into the passivation orientation of molecules on the surface is a challenge for rational molecular design. In this study, aminothiol hydrochlorides with different alkyl chains but identical electron-donating (-SH) and electron-withdrawing (-NH3 +) groups were employed to investigate the interplay between molecular structure, orientation, and interaction on perovskite surface. The 2-Aminoethane-1-thiol hydrochloride with shorter alkyl chains exhibited a preference of parallel orientations, which facilitating stronger interactions with the surface defects through strong coordination and hydrogen bonding. The resultant perovskite films following defect passivation demonstrate reduced ion migration, inhibition of nonradiative recombination, and more n-type characteristics for efficient electron transfer. Consequently, an impressive power conversion efficiency of 25 % was achieved, maintaining 95 % of its initial efficiency after 500 hours of continuous maximum power point tracking.

Preventing lead leakage in perovskite solar cells and modules with a low-cost and stable chemisorption coating.

Despite the promising commercial prospects of perovskite solar cells, the issue of lead toxicity continues to hinder their future industrial applications. Here, we report a low-cost and rapidly degraded sulfosuccinic acid-modified polyvinyl alcohol (SMP) coating that prevents lead leakage and enhances device stability without compromising device performance. Even under different strict conditions (simulated heavy rain, acid rain, high temperatures, and competing ions), the coatings effectively prevent lead leakage by over 99%. After 75 days of outdoor exposure, the coating still demonstrates similar lead sequestration efficiency (SQE). In addition, it can be applied to different device structures (n-i-p and p-i-n) and modules, with over 99% SQE, making it a general method for preventing lead leakage.

Non-Fullerene Acceptors Assisted Target Therapy for Interface Treatment Enable High Performance Inverted Perovskite Solar Cells.

Targeted treatment of the interface between electron transport layers (ETL) and perovskite layers is highly desirable for achieving passivating effects and suppressing carrier nonradiative recombination, leading to high performance and long-term stability in perovskite solar cells (PSCs). In this study, a series of non-fullerene acceptors (NFAs, Y-H, Y-F, and Y-Cl) are introduced to optimize the properties of the perovskite/ETL interface. This optimization involves passivating Pb2+ defects, releasing stress, and modulating carrier dynamics through interactions with the perovskite. Remarkably, after modifying with NFAs, the absorption range of perovskite films into the near-infrared region is extended. As expected, Y-F, with the largest electrostatic potential, facilitates the strongest interaction between the perovskite and its functional groups. Consequently, champion power conversion efficiencies of 21.17%, 22.21%, 23.25%, and 22.31% are achieved for control, Y-H-, Y-F-, and Y-Cl-based FA0.88Cs0.12PbI2.64Br0.36 (FACs) devices, respectively. This treatment also enhances the heat stability and air stability of the corresponding devices. Additionally, these modifier layers are applied to enhance the efficiency of Cs0.05(FA0.95MA0.05)0.95PbI2.64Br0.36 (FAMA) devices. Notably, a champion PCE exceeding 24% is achieved in the Y-F-based FAMA device. Therefore, this study provides a facile and effective approach to target the interface, thereby improving the efficiency and stability of PSCs.

Multifunctional Trifluoroborate Additive for Simultaneous Carrier Dynamics Governance and Defects Passivation to Boost Efficiency and Stability of Inverted Perovskite Solar Cells.

The main obstacles to promoting the commercialization of perovskite solar cells (PSCs) include their record power conversion efficiency (PCE), which still remains below the Shockley-Queisser limit, and poor long-term stability, attributable to crystallographic defects in perovskite films and open-circuit voltage (Voc) loss in devices. In this study, potassium (4-tert-butoxycarbonylpiperazin-1-yl) methyl trifluoroborate (PTFBK) was employed as a multifunctional additive to target and modulate bulk perovskite defects and carrier dynamics of PSCs. Apart from simultaneously passivating anionic and cationic defects, PTFBK could also optimize the energy-level alignment of devices and weaken the interaction between carriers and longitudinal optical phonons, resulting in a carrier lifetime of greater than 3 µs. Furthermore, it inhibited non-radiative recombination and improved the crystallization capacity in the target perovskite film. Hence, the target rigid and flexible p-i-n PSCs yielded champion PCEs of 24.99 % and 23.48 %, respectively. More importantly, due to hydrogen bonding between formamidinium and fluorine, the target devices exhibited remarkable thermal, humidity, and operational tracking at maximum power point stabilities. The reduced Young's modulus and residual stress in the perovskite layer also provided excellent bending stability for flexible target devices.

Dynamic covalent polymer engineering for stable and self-healing perovskite solar cells.

Perovskite films are susceptible to degradation during their service period due to their weak mechanical properties. Acylhydrazone-bonded waterborne polyurethane (Ab-WPU) was employed as dynamic covalent polymer engineering to develop self-healing perovskite solar cells (SHPSCs). Ab-WPU enhances the crystallinity of the perovskite film, passivates the defects of the perovskite film through functional groups, and demonstrates promising flexibility and mild temperature self-healing properties of SHPSCs. The champion efficiency of SHPSCs on rigid and flexible substrates reaches 24.2% and 21.27% respectively. The moisture and heat stability of devices were improved. After 1000 bending cycles, the Ab-WPU-modified flexible device can be restored to an efficiency of over 95% of its original efficiency by heating to 60 °C. This is because the dynamic acylhydrazone bond can be activated to repair perovskite film defects at a mild temperature of 60 °C as evidenced by in situ AFM studies. This strategy provides an effective pathway for dynamic self-healing materials in PSCs under operational conditions.

A Deformable Additive on Defects Passivation and Phase Segregation Inhibition Enables the Efficiency of Inverted Perovskite Solar Cells over 24.

The defects and phase segregation in perovskite will significantly reduce the performance and stability of perovskite solar cells (PSCs). In this work, a deformable coumarin is employed as a multifunctional additive for formamidinium-cesium (FA-Cs) perovskite. During the annealing process of perovskite, the partial decomposition of coumarin passivates the Pb2+ , iodine, and organic cation defects. Additionally, coumarin can affect colloidal size distributions, resulting in relatively large grain size and good crystallinity of target perovskite film. Hence, the carrier extraction/transport can be promoted, trap-assisted recombination is reduced, and energy levels are optimized in target perovskite films. Furthermore, the coumarin treatment can significantly release residual stress. As a result, the champion power conversion efficiencies (PCEs) of 23.18% and 24.14% are obtained for Br-rich (FA0.88 Cs0.12 PbI2.64 Br0.36 ) and Br-poor (FA0.96 Cs0.04 PbI2.8 Br0.12 ) based devices, respectively. The flexible PSCs based on Br-poor perovskite exhibit an excellent PCE of 23.13%, one of the highest values for flexible PSCs reported to date. Due to the inhibition of phase segregation, the target devices exhibit excellent thermal and light stability. This work provides new insights into the additive engineering of passivating defects, stress relief, and inhibition of phase segregation of perovskite films, offering a reliable method to develop state-of-the-art solar cells.

Rational Design of Ferroelectric 2D Perovskite for Improving the Efficiency of Flexible Perovskite Solar Cells Over 23 .

Despite the great progress of flexible perovskite solar cells (f-PSCs), it still faces several challenges during the homogeneous fabrication of high-quality perovskite thin films, and overcoming the insufficient exciton dissociation. To the ends, we rationally design the ferroelectric two-dimensional (2D) perovskite based on pyridine heterocyclic ring as the organic interlayer. We uncover that incorporation of the ferroelectric 2D material into 3D perovskite induces an increased built-in electric field (BEF), which enhances the exciton dissociation efficiency in the device. Moreover, the 2D seeds could assist the 3D crystallization by forming more homogeneous and highly-oriented perovskite crystals. As a result, an impressive power conversion efficiency (PCE) over 23 % has been achieved by the f-PSCs with outstanding ambient stability. Moreover, the piezo/ferroelectric 2D perovskite intrigues a decreased hole transport barriers at the ITO/perovskite interface under tensile stress, which opens new possibilities for developing highly-efficient f-PSCs.

Divalent Anionic Doping in Perovskite Solar Cells for Enhanced Chemical Stability.

The chemical stabilities of hybrid perovskite materials demand further improvement toward long-term and large-scale photovoltaic applications. Herein, the enhanced chemical stability of CH3 NH3 PbI3 is reported by doping the divalent anion Se2- in the form of PbSe in precursor solutions to enhance the hydrogen-bonding-like interactions between the organic cations and the inorganic framework. As a result, in 100% humidity at 40 °C, the 10% w/w PbSe-doped CH3 NH3 PbI3 films exhibited >140-fold stability improvement over pristine CH3 NH3 PbI3 films. As the PbSe-doped CH3 NH3 PbI3 films maintained the perovskite structure, a top efficiency of 10.4% with 70% retention after 700 h aging in ambient air is achieved with an unencapsulated 10% w/w PbSe:MAPbI3 -based cell. As a bonus, the incorporated Se2- also effectively suppresses iodine diffusion, leading to enhanced chemical stability of the silver electrodes.

Impact of grain boundaries on efficiency and stability of organic-inorganic trihalide perovskites.

Organic-inorganic perovskite solar cells have attracted tremendous attention because of their remarkably high power conversion efficiencies. To further improve device performance, it is imperative to obtain fundamental understandings on the photo-response and long-term stability down to the microscopic level. Here, we report the quantitative nanoscale photoconductivity imaging on two methylammonium lead triiodide thin films with different efficiencies by light-stimulated microwave impedance microscopy. The microwave signals are largely uniform across grains and grain boundaries, suggesting that microstructures do not lead to strong spatial variations of the intrinsic photo-response. In contrast, the measured photoconductivity and lifetime are strongly affected by bulk properties such as the sample crystallinity. As visualized by the spatial evolution of local photoconductivity, the degradation process begins with the disintegration of grains rather than nucleation and propagation from visible boundaries between grains. Our findings provide insights to improve the electro-optical properties of perovskite thin films towards large-scale commercialization.

Determination of the True Lateral Grain Size in Organic-Inorganic Halide Perovskite Thin Films.

In this letter, methylammonium lead iodide (MAPbI3) thin films were examined via piezoresponse force microscopy (PFM) and nanoindentation (NI) to determine if long-range atomic order existed across the full width and depth of the apparent grains. From the PFM, the piezoelectric response of the films was strongly correlated with low-index planes of the crystal structure and ferroelastic domains in macroscale solution-grown MAPbI3 crystals, which implied long-range order near the top surface. From the NI, it was found that the induced cracks were straight and extended across the full width of the apparent grains, which indicated that the long-range order was not limited to the near-surface region, but extended through the film thickness. Interestingly, the two MAPbI3 processes examined resulted in subtle differences in the extracted electro-mechanical and fracture properties, but exhibited similar power conversion efficiencies of >17% in completed devices.

Long-range hot-carrier transport in hybrid perovskites visualized by ultrafast microscopy.

The Shockley-Queisser limit for solar cell efficiency can be overcome if hot carriers can be harvested before they thermalize. Recently, carrier cooling time up to 100 picoseconds was observed in hybrid perovskites, but it is unclear whether these long-lived hot carriers can migrate long distance for efficient collection. We report direct visualization of hot-carrier migration in methylammonium lead iodide (CH3NH3PbI3) thin films by ultrafast transient absorption microscopy, demonstrating three distinct transport regimes. Quasiballistic transport was observed to correlate with excess kinetic energy, resulting in up to 230 nanometers transport distance that could overcome grain boundaries. The nonequilibrium transport persisted over tens of picoseconds and ~600 nanometers before reaching the diffusive transport limit. These results suggest potential applications of hot-carrier devices based on hybrid perovskites.

300% Enhancement of Carrier Mobility in Uniaxial-Oriented Perovskite Films Formed by Topotactic-Oriented Attachment.

Organic-inorganic perovskites with intriguing optical and electrical properties have attracted significant research interests due to their excellent performance in optoelectronic devices. Recent efforts on preparing uniform and large-grain polycrystalline perovskite films have led to enhanced carrier lifetime up to several microseconds. However, the mobility and trap densities of polycrystalline perovskite films are still significantly behind their single-crystal counterparts. Here, a facile topotactic-oriented attachment (TOA) process to grow highly oriented perovskite films, featuring strong uniaxial-crystallographic texture, micrometer-grain morphology, high crystallinity, low trap density (≈4 × 1014 cm-3 ), and unprecedented 9 GHz charge-carrier mobility (71 cm2 V-1 s-1 ), is demonstrated. TOA-perovskite-based n-i-p planar solar cells show minimal discrepancies between stabilized efficiency (19.0%) and reverse-scan efficiency (19.7%). The TOA process is also applicable for growing other state-of-the-art perovskite alloys, including triple-cation and mixed-halide perovskites.

Electronic and Morphological Inhomogeneities in Pristine and Deteriorated Perovskite Photovoltaic Films.

We perform scanning microwave microscopy (SMM) to study the spatially varying electronic properties and related morphology of pristine and degraded methylammonium lead-halide (MAPI) perovskite films fabricated under different ambient humidity. We find that higher processing humidity leads to the emergence of increased conductivity at the grain boundaries but also correlates with the appearance of resistive grains that contain PbI2. Deteriorated films show larger and increasingly insulating grain boundaries as well as spatially localized regions of reduced conductivity within grains. These results suggest that while humidity during film fabrication primarily benefits device properties due to the passivation of traps at the grain boundaries and self-doping, it also results in the emergence of PbI2-containing grains. We further establish that MAPI film deterioration under ambient conditions proceeds via the spatially localized breakdown of film conductivity, both at grain boundaries and within grains, due to local variations in susceptibility to deterioration. These results confirm that PbI2 has both beneficial and adverse effects on device performance and provide new means for device optimization by revealing spatial variations in sample conductivity as well as morphological differences in resistance to sample deterioration.

Do grain boundaries dominate non-radiative recombination in CH3NH3PbI3 perovskite thin films?

Here, we examine grain boundaries (GBs) with respect to non-GB regions (grain surfaces (GSs) and grain interiors (GIs)) in high-quality micrometer-sized perovskite CH3NH3PbI3 (or MAPbI3) thin films using high-resolution confocal fluorescence-lifetime imaging microscopy in conjunction with kinetic modeling of charge-transport and recombination processes. We show that, contrary to previous studies, GBs in our perovskite MAPbI3 thin films do not lead to increased recombination but that recombination in these films happens primarily in the non-GB regions (i.e., GSs or GIs). We also find that GBs in these films are not transparent to photogenerated carriers, which is likely associated with a potential barrier at GBs. Even though GBs generally display lower luminescence intensities than GSs/GIs, the lifetimes at GBs are no worse than those at GSs/GIs, further suggesting that GBs do not dominate non-radiative recombination in MAPbI3 thin films.

Electrochemical impedance analysis of perovskite-electrolyte interfaces.

The flat band potentials and carrier densities of spin coated and sprayed MAPbI3, FA0.85Cs0.15PbI3, and MAPbBr3 perovskite films were determined using the Mott-Schottky relation. The films developed a space charge layer and exhibited p-type conduction with a carrier concentration of ∼1016 cm-3 for spin coated films. Electrochemical impedance spectra showed typical space charge impedance at frequencies >1 kHz, and an exceptional high capacitance at frequency <1 kHz owing to an ion diffusion component.

Large polarization-dependent exciton optical Stark effect in lead iodide perovskites.

A strong interaction of a semiconductor with a below-bandgap laser pulse causes a blue-shift of the bandgap transition energy, known as the optical Stark effect. The energy shift persists only during the pulse duration with an instantaneous response time. The optical Stark effect has practical relevance for applications, including quantum information processing and communication, and passively mode-locked femtosecond lasers. Here we demonstrate that solution-processable lead-halide perovskites exhibit a large optical Stark effect that is easily resolved at room temperature resulting from the sharp excitonic feature near the bandedge. We also demonstrate that a polarized pump pulse selectively shifts one spin state producing a spin splitting of the degenerate excitonic states. Such selective spin manipulation is an important prerequisite for spintronic applications. Our result implies that such hybrid semiconductors may have great potential for optoelectronic applications beyond photovoltaics.

Facile fabrication of large-grain CH3NH3PbI3-xBrx films for high-efficiency solar cells via CH3NH3Br-selective Ostwald ripening.

Organometallic halide perovskite solar cells (PSCs) have shown great promise as a low-cost, high-efficiency photovoltaic technology. Structural and electro-optical properties of the perovskite absorber layer are most critical to device operation characteristics. Here we present a facile fabrication of high-efficiency PSCs based on compact, large-grain, pinhole-free CH3NH3PbI3-xBrx (MAPbI3-xBrx) thin films with high reproducibility. A simple methylammonium bromide (MABr) treatment via spin-coating with a proper MABr concentration converts MAPbI3 thin films with different initial film qualities (for example, grain size and pinholes) to high-quality MAPbI3-xBrx thin films following an Ostwald ripening process, which is strongly affected by MABr concentration and is ineffective when replacing MABr with methylammonium iodide. A higher MABr concentration enhances I-Br anion exchange reaction, yielding poorer device performance. This MABr-selective Ostwald ripening process improves cell efficiency but also enhances device stability and thus represents a simple, promising strategy for further improving PSC performance with higher reproducibility and reliability.

Electron-Rotor Interaction in Organic-Inorganic Lead Iodide Perovskites Discovered by Isotope Effects.

We report on the carrier-rotor coupling effect in perovskite organic-inorganic hybrid lead iodide (CH3NH3PbI3) compounds discovered by isotope effects. Deuterated organic-inorganic perovskite compounds including CH3ND3PbI3, CD3NH3PbI3, and CD3ND3PbI3 were synthesized. Devices made from regular CH3NH3PbI3 and deuterated CH3ND3PbI3 exhibit comparable performance in band gap, current-voltage, carrier mobility, and power conversion efficiency. However, a time-resolved photoluminescence (TRPL) study reveals that CH3NH3PbI3 exhibits notably longer carrier lifetime than that of CH3ND3PbI3, in both thin-film and single-crystal formats. Furthermore, the comparison in carrier lifetime between CD3NH3PbI3 and CH3ND3PbI3 single crystals suggests that vibrational modes in methylammonium (MA(+)) have little impact on carrier lifetime. In contrast, the fully deuterated compound CD3ND3PbI3 reconfirmed the trend of decreasing carrier lifetime upon the increasing moment of inertia of cationic MA(+). Polaron model elucidates the electron-rotor interaction.