In the current study, platinum-present as a negligible component (below 1 ppb, the detection limit of the HR-ICP-MS at the dilutions used) in real industrial hydrometallurgical process solutions-was recovered by an electrodeposition-redox replacement (EDRR) method on pyrolyzed carbon (PyC) electrode, a method not earlier applied to metal recovery. The recovery parameters of the EDRR process were initially investigated using a synthetic nickel electrolyte solution ([Ni] = 60 g/L, [Ag] = 10 ppm, [Pt] = 20 ppm, [H2SO4] = 10 g/L), and the results demonstrated an extraordinary increase of 3 × 105 in the [Pt]/[Ni] on the electrode surface cf. synthetic solution. EDRR recovery of platinum on PyC was also tested with two real industrial process solutions that contained a complex multimetal solution matrix: Ni as the major component (>140 g/L) and very low contents of Pt, Pd, and Ag (i.e., <1 ppb, 117 and 4 ppb, respectively). The selectivity of Pt recovery by EDRR on the PyC electrode was found to be significant-nanoparticles deposited on the electrode surface comprised on average of 90 wt % platinum and a [Pt]/[Ni] enrichment ratio of 1011 compared to the industrial hydrometallurgical solution. Furthermore, other precious metallic elements like Pd and Ag could also be enriched on the PyC electrode surface using the same methodology. This paper demonstrates a remarkable advancement in the recovery of trace amounts of platinum from real industrial solutions that are not currently considered as a source of Pt metal.
Cellulose acetate (CA)-based membranes are used for Mg dissolution control: the permeability of the membrane is adjusted by additions of the polyelectrolyte, poly(N,N-dimethylaminoethyl methacrylate) (PDMAEMA). Spin-coated films were characterized with FT-IR, and once exposed to an aqueous solution the film distends and starts acting as a membrane which controls the flow of ions and H2 gas. Electrochemical measurements (linear sweep voltammograms, open-circuit potential, and polarization) show that by altering the CA:PDMAEMA ratio the dissolution rate of Mg can be controlled. Such a control over Mg dissolution is crucial if Mg is to be considered as a viable, temporary biomedical implant material. Furthermore, the accumulation of corrosion products between the membrane and the sample diminishes the undesirable effects of high local pH and H2 formation which takes place during the corrosion process.
Body Fluids/chemistry , Cellulose/analogs & derivatives , Coated Materials, Biocompatible/chemical synthesis , Magnesium/chemistry , Methacrylates/chemistry , Nylons/chemistry , Cellulose/chemistry , Corrosion , Diffusion , Electrolytes/chemistry , Materials Testing
Site-specific assembly of gold nanoparticles on a polysaccharide surface was accomplished via a straightforward method exploiting interfacial polymer blends, selective protein adsorption and electrostatic interaction. The method could be useful in further applications due to the universal nature of the utilized phenomena.
Gold/chemistry , Metal Nanoparticles/chemistry , Polysaccharides/chemistry , Serum Albumin, Bovine/chemistry , Adsorption , Animals , Cattle , Cellulose/chemistry , Surface Properties
Mesoporous TiO(2) nanocontainers (NCs) covered with polyelectrolyte multilayers were adsorbed on self-assembled monolayer (SAM) modified gold substrates at different values of pH and ionic strength. The adsorption process was followed in situ by means of a quartz crystal microbalance (QCM) and the morphology of the adsorbate was investigated by means of FE-SEM images taken of the substrates after each adsorption process. Deposition could be achieved if either the particles and the surface had opposite charge, or if the salt concentration was sufficiently high, reducing the repulsion between the spheres and the surface. In the latter case the adsorption kinetics could be explained in the context of the DLVO-theory. Using conditions of like charges, one has a means to control the speed of deposition by means of ionic strength. However, interparticle aggregation and cluster deposition on the surface were observed at high ionic strength. Such conditions have to be avoided to obtain a uniform deposition of separated nanocontainers on the surface.
