Structuring restricted amorphous molecular chains in the reinforced cellulose film by uniaxial stretching.

The construction of the preferred orientation structure by stretching is an efficient strategy to fabricate high-performance cellulose film and it is still an open issue whether crystalline structure or amorphous molecular chain is the key factor in determining the enhanced mechanical performance. Herein, uniaxial stretching with constant width followed by drying in a stretching state was carried out to cellulose hydrogels with physical and chemical double cross-linking networks, achieving high-performance regenerated cellulose films (RCFs) with an impressive tensile strength of 154.5 MPa and an elastic modulus of 5.4 GPa. The hierarchical structure of RCFs during uniaxial stretching and drying was systematically characterized from micro- to nanoscale, including microscopic morphology, crystalline structure as well as relaxation behavior at a molecular level. The two-dimensional correlation spectra of dynamic mechanical analysis and Havriliak-Negami fitting results verified that the enhanced mechanical properties of RCFs were mainly attributed to the stretch-induced tight packing and restricted relaxation of amorphous molecular chains. The new insight concerning the contribution of molecular chains in the amorphous region to the enhancement of mechanical performance for RCFs is expected to provide valuable guidance for designing and fabricating high-performance eco-friendly cellulose-based films.

Leptin attenuates the osteogenic induction potential of BMP9 by increasing ß-catenin malonylation modification via Sirt5 down-regulation.

BMP9 has demonstrated significant osteogenic potential. In this study, we investigated the effect of Leptin on BMP9-induced osteogenic differentiation. Firstly, we found Leptin was decreased during BMP9-induced osteogenic differentiation and serum Leptin concentrations were increased in the ovariectomized (OVX) rats. Both in vitro and in vivo, exogenous expression of Leptin inhibited the process of osteogenic differentiation, whereas silencing Leptin enhanced. Exogenous Leptin could increase the malonylation of ß-catenin. However, BMP9 could increase the level of Sirt5 and subsequently decrease the malonylation of ß-catenin; the BMP9-induced osteogenic differentiation was inhibited by silencing Sirt5. These data suggested that Leptin can inhibit the BMP9-induced osteogenic differentiation, which may be mediated through reducing the activity of Wnt/ß-catenin signalling via down-regulating Sirt5 to increase the malonylation level of ß-catenin partly.

Regulatory frameworks involved in the floral induction, formation and developmental programming of woody horticultural plants: a case study on blueberries.

Flowering represents a crucial stage in the life cycles of plants. Ensuring strong and consistent flowering is vital for maintaining crop production amidst the challenges presented by climate change. In this review, we summarized key recent efforts aimed at unraveling the complexities of plant flowering through genetic, genomic, physiological, and biochemical studies in woody species, with a special focus on the genetic control of floral initiation and activation in woody horticultural species. Key topics covered in the review include major flowering pathway genes in deciduous woody plants, regulation of the phase transition from juvenile to adult stage, the roles of CONSTANS (CO) and CO-like gene and FLOWERING LOCUS T genes in flower induction, the floral regulatory role of GA-DELLA pathway, and the multifunctional roles of MADS-box genes in flowering and dormancy release triggered by chilling. Based on our own research work in blueberries, we highlighted the central roles played by two key flowering pathway genes, FLOWERING LOCUS T and SUPPRESSOR OF OVEREXPRESSION OF CONSTANS 1, which regulate floral initiation and activation (dormancy release), respectively. Collectively, our survey shows both the conserved and diverse aspects of the flowering pathway in annual and woody plants, providing insights into the potential molecular mechanisms governing woody plants. This paves the way for enhancing the resilience and productivity of fruit-bearing crops in the face of changing climatic conditions, all through the perspective of genetic interventions.

Nanopatterning of beaded poly(lactic acid) nanofibers for highly electroactive, breathable, UV-shielding and antibacterial protective membranes.

Despite great potential in fabrication of biodegradable protective membranes by electrospinning of poly(lactic acid) (PLA) nanofibers, it is still thwarted by smooth surfaces and poor electroactivity that challenge the promotion of electret properties and long-term air filtration performance. Here, a microwave-assisted synthetic method was used to customize dielectric TiO2 nanocrystals of ultrasmall and uniform dimensions (∼30 nm), which were homogeneously embedded at beaded PLA nanofibers (PLA@TiO2, diameter of around 280 nm) by the combined "electrospinning-electrospray" approach. With small amounts of TiO2 (2, 4 and 6 wt%), the nanopatterned PLA@TiO2 nanofibrous membranes (NFMs) were characterized by largely increased dielectric constants (nearly 1.9), surface potential (up to 1.63 kV) and triboelectric properties (output voltage of 12.2 V). Arising from the improved electroactivity and self-charging mechanisms, the nanopatterned PLA@TiO2 NFMs exhibited remarkable PM0.3 filtration properties (97.9 %, 254.6 Pa) even at the highest airflow rate of 85 L/min, surpassing those of pure PLA membranes (86.2 %, 483.7 Pa). This was moreover accompanied by inhibition rates of 100 % against both E. coli and S. aureus, as well as excellent UV-blocking properties (UPF as high as 3.8, TUVA of 50.9 % and TUVB of 20.1 %). The breathable and electroactive nanopatterned PLA NFMs permit promising applications in multifunctional protective membranes toward excellent UV shielding and high-efficiency removal of both PMs and pathogens.

Editing VvDXS1 for the creation of muscat flavour in Vitis vinifera cv. Scarlet Royal.

Muscat flavour represents a group of unique aromatic attributes in some grape varieties. Biochemically, grape berries with muscat flavour produce high levels of monoterpenes. Monoterpene biosynthesis is mainly through the DOXP/MEP pathway, and VvDXS1 encodes the first enzyme in this plastidial pathway of terpene biosynthesis in grapevine. A single-point mutation resulting in the substitution of a lysine with an asparagine at position 284 in the VvDXS1 protein has previously been identified as the major cause for producing muscat flavour in grapes. In this study, the same substitution in the VvDXS1 protein was successfully created through prime editing in the table grape Vitis vinifera cv. 'Scarlet Royal'. The targeted point mutation was detected in most of the transgenic vines, with varying editing efficiencies. No unintended mutations were detected in the edited alleles, either by PCR Sanger sequencing or by amplicon sequencing. More than a dozen edited vines were identified with an editing efficiency of more than 50%, indicating that these vines were likely derived from single cells in which one allele was edited. These vines had much higher levels of monoterpenes in their leaves than the control, similar to what was found in leaf samples between field-grown muscat and non-muscat grapes.

Hierarchically porous cellulose-based carbon aerogels with N-doped skeletons and encapsulated iron-based catalysts for efficient tetracycline catalytic degradation.

Three-dimensional interpenetrating and hierarchically porous carbon material is an efficient catalyst support in water remediation and it is still a daunting challenge to establish the relationship between hierarchically porous structure and catalytic degradation performance. Herein, a highly porous silica (SiO2)/cellulose-based carbon aerogel with iron-based catalyst (FexOy) was fabricated by in-situ synthesis, freeze-drying and pyrolysis, where the addition of SiO2 induced the hierarchically porous morphology and three-dimensional interpenetrating sheet-like network with nitrogen doping. The destruction of cellulose crystalline structure by SiO2 and the iron-catalyzed breakdown of glycosidic bonds synergistically facilitated the formation of electron-rich graphite-like carbon skeleton. The unique microstructure is confirmed to be favorable for the diffusion of reactants and electron transport during catalytic process, thus boosting the catalytic degradation performance of carbon aerogels. As a result, the catalytic degradation efficiency of tetracycline under light irradiation by adding only 5 mg of FexOy/SiO2 cellulose carbon aerogels was as high as 90 % within 60 min, demonstrating the synergistic effect of photocatalysis and Fenton reaction. This ingenious structure design provides new insight into the relationship between hierarchically porous structure of carbon aerogels and their catalytic degradation performance, and opens a new avenue to develop cellulose-based carbon aerogel catalysts with efficient catalytic performance.

Self-Charging, Breathable, and Antibacterial Poly(lactic acid) Nanofibrous Air Filters by Surface Engineering of Ultrasmall Electroactive Nanohybrids.

Despite the great promise in the development of biodegradable and ecofriendly air filters by electrospinning of poly(lactic acid) (PLA) nanofibrous membranes (NFMs), the as-electrospun PLA nanofibers are generally characterized by poor electroactivity and smooth surface, challenging the exploitation of electrostatic adsorption and physical interception that are in need for efficient removal of pathogens and particulate matters (PMs). Herein, a combined "electrospinning-electrospray" strategy was disclosed to functionalize the PLA nanofibers by direct anchoring of highly dielectric BaTiO3@ZIF-8 nanohybrids (BTO@ZIF-8), conferring simultaneous promotion of surface roughness, electret properties (surface potential as high as 7.5 kV), and self-charging capability (∼190% increase in tribo-output voltage compared to that of pure PLA). Benefiting from the well-tailored morphology and increased electroactivity, the electrospun-electrosprayed PLA/BTO@ZIF-8 exhibited excellent PM-capturing performance (up to 96.54% for PM0.3 and 99.49% for PM2.5) while providing desirable air resistance (only 87 Pa at 32 L/min) due primarily to the slip flow of air molecules over the nanohybrid protrusions. This was accompanied by excellent antibacterial properties (99.9% inhibition against both Staphylococcus aureus and Escherichia coli), arising presumably from the synergistic effects of enhanced reactive oxygen species (ROS) generation, plentiful ion release, and surface charges. Our proposed strategy opens up pathways to afford exceptional combination of high-efficiency and low-resistance filtration, excellent antibacterial performance, and mechanical robustness without sacrificing the biodegradation profiles of PLA NFMs, holding potential implications for efficient and long-term healthcare.

Basic leucine zipper gene VvbZIP61 is expressed at a quantitative trait locus for high monoterpene content in grape berries.

The widely appreciated muscat flavor of grapes and wine is mainly attributable to the monoterpenes that accumulate in ripe grape berries. To identify quantitative trait loci (QTL) for grape berry monoterpene content, an F1 mapping population was constructed by a cross between two grapevine genotypes, one with neutral aroma berries (cv. 'Beifeng') and the other with a pronounced muscat aroma (elite Vitis vinifera line '3-34'). A high-density genetic linkage map spanning 1563.7 cM was constructed using 3332 SNP markers that were assigned to 19 linkage groups. Monoterpenes were extracted from the berry of the F1 progeny, then identified and quantified by gas chromatography-mass spectrometry. Twelve stable QTLs associated with the amounts of 11 monoterpenes in berries were thus identified. In parallel, the levels of RNA in berries from 34 diverse cultivars were estimated by RNA sequencing and compared to the monoterpene content of the berries. The expression of five genes mapping to stable QTLs correlated well with the monoterpene content of berries. These genes, including the basic leucine zipper VvbZIP61 gene on chromosome 12, are therefore considered as potentially being involved in monoterpene metabolism. Overexpression of VvbZIP61 in Vitis amurensis callus through Agrobacterium-mediated transformation significantly increased the accumulation of several monoterpenes in the callus, including nerol, linalool, geranial, geraniol, ß-myrcene, and D-limonene. It is hypothesized that VvbZIP61 expression acts to increase muscat flavor in grapes. These results advance our understanding of the genetic control of monoterpene biosynthesis in grapes and provide important information for the marker-assisted selection of aroma compounds in grape breeding.

Robust, Fully Biodegradable Films of Polyesters Realized by In Situ Formation of an Interconnected Multi-Nanolayer Structure under Extensional Flow.

Multilayer structures are not only applied to manipulate properties of synthetic polymer materials such as rainbow films and barrier films but also widely discovered in natural materials like nacre. In this work, in situ formation of an interconnected multi-nanolayer (IMN) structure in poly(butylene adipate-co-terephthalate) (PBAT)/poly(butylene succinate) (PBS) cocontinuous blends is designed by an extensional flow field during a "casting-thermal stretching" process, combining the properties of two components to a large extent. Hierarchical structures including phase morphology, crystal structure, and lamellar crystals in IMN films have been revealed, which clearly identifies the crucial role of extensional flow. The oriented PBAT phase in the IMN structure can be beneficial to the epitaxial growth of PBS crystals onto the PBAT nanolayers, thus improving interfacial adhesions. Furthermore, intense extensional stress can also promote crystallinity and thicken the lamellar structure. Given such distinct features in the fully biodegradable films, a simultaneous enhancement in tear strength, tensile strength, and puncture resistance has been achieved. To the best of our knowledge, the tear strength of IMN films about 285.9 kN/m is the highest level in the previous works of this system. Moreover, the proposed fabrication way of the IMN structure is facile and scalable, which is highly expected to be an efficient strategy for development of structured biodegradable polymers with excellent comprehensive properties.

Extensional Stress-Induced Ductility of Poly(l-lactide) Films: Role of the Entangled Network in Amorphous Regions.

The relationship between the density of the entangled amorphous network and the ductility of oriented poly(l-lactide) (PLLA) films is explored based on the preferential hydrolysis of the amorphous regions in phosphate buffer solution (PBS). PLLA films with a balance of ductility and stiffness have been prepared by the "casting-annealing stretching" based on mechanical rejuvenation, and the structural evolution and mechanical properties at different hydrolysis durations have been identified. Various stages are found during the transition of ductility to brittleness for hydrolyzed PLLA films. First, the elongation at break for hydrolyzed PLLA films remains unchanged in the first stage of hydrolysis and then gradually decreases. Eventually, the films turn to be brittle in the third stage. The strain-hardening modulus (GR) of the hydrolyzed films is utilized to reflect the density of the entangled amorphous network, and a gradual decrease of GR with hydrolysis time indicates the decisive role of the amorphous entanglement network in the mechanical rejuvenation-induced ductility of PLLA. The quantitative relationship between the entangled amorphous network and the stress-induced ductility of PLLA films is revealed. The dependence of deformation behavior on entangled amorphous network density is closely correlated to activated primary structure during deformation. The intact chain network plays a crucial role in sufficiently activating the primary structure to yield and disentanglement during the subsequent necking. These findings could advance the understanding of the PLLA's ductility induced by mechanical rejuvenation and offer guidance for awakening the intrinsic toughness of PLLA.

Enhanced Dielectric Properties of All-Cellulose Composite Film via Modulating Hydroxymethyl Conformation and Hydrogen Bonding Network.

Cellulose-based dielectrics with attractive dielectric performance are promising candidates to develop eco-friendly electrostatic energy storage devices. Herein, all-cellulose composite films with superior dielectric constant were fabricated by manipulating the dissolution temperature of native cellulose, where we revealed the relationship among the hierarchical microstructure of the crystalline structure, the hydrogen bonding network, the relaxation behavior at a molecular level, and the dielectric performance of the cellulose film. The coexistence of cellulose I and cellulose II led to a weakened hydrogen bonding network and unstable C6 conformations. The increased mobility of cellulose chains in the cellulose I-amorphous interphase enhanced the dielectric relaxation strength of side groups and localized main chains. As a result, the as-prepared all-cellulose composite films exhibited a fascinating dielectric constant of as high as 13.9 at 1000 Hz. This work proposed here provides a significant step toward fundamentally understanding the dielectric relaxation of cellulose, thus developing high-performance and eco-friendly cellulose-based film capacitors.

Toward Excellent Energy Storage Performance via Well-Aligned and Isolated Interfaces in Multicomponent Polypropylene-Based All-Organic Polymer Dielectric Films.

Polypropylene (PP) serves as an excellent commercialized polymer dielectric film owing to its high breakdown strength, excellent self-healing ability, and flexibility. However, its low dielectric constant causes the large volume of the capacitor. Constructing multicomponent polypropylene-based all-organic polymer dielectric films is a facile strategy for achieving high energy density and efficiency simultaneously. Thereinto, the interfaces between the components become the key factors that determine the energy storage performance of the dielectric films. In this work, we propose to fabricate high-performance polyamide 513 (PA513)/PP all-organic polymer dielectric films via the construction of abundant well-aligned and isolated nanofibrillar interfaces. Laudably, a significant enhancement in the breakdown strength is achieved from 573.1 MV/m of pure PP to 692.3 MV/m with 5 wt % of PA513 nanofibrils. Besides, a maximum discharge energy density of about 4.4 J/cm2 is realized with 20 wt % of PA513 nanofibrils, which is about 1.6-folds higher than pure PP. Simultaneously, the energy efficiency of samples with modulated interfaces maintains higher than 80% up to 600 MV/m, which is much higher than pure PP of about 40.7% at 550 MV/m. This work provides a new strategy to fabricate high-performance multicomponent all-organic polymer dielectric films on an industrial scale.

Multiple transcriptome comparisons reveal the essential roles of FLOWERING LOCUS T in floral initiation and SOC1 and SVP in floral activation in blueberry.

The flowering mechanisms, especially chilling requirement-regulated flowering, in deciduous woody crops remain to be elucidated. Flower buds of northern highbush blueberry cultivar Aurora require approximately 1,000 chilling hours to bloom. Overexpression of a blueberry FLOWERING LOCUS T (VcFT) enabled precocious flowering of transgenic "Aurora" mainly in non-terminated apical buds during flower bud formation, meanwhile, most of the mature flower buds could not break until they received enough chilling hours. In this study, we highlighted two groups of differentially expressed genes (DEGs) in flower buds caused by VcFT overexpression (VcFT-OX) and full chilling. We compared the two groups of DEGs with a focus on flowering pathway genes. We found: 1) In non-chilled flower buds, VcFT-OX drove a high VcFT expression and repressed expression of a major MADS-box gene, blueberry SUPPRESSOR OF OVEREXPRESSION OF CONSTANS 1 (VcSOC1) resulting an increased VcFT/VcSOC1 expression ratio; 2) In fully chilled flower buds that are ready to break, the chilling upregulated VcSOC1 expression in non-transgenic "Aurora" and repressed VcFT expression in VcFT-OX "Aurora", and each resulted in a decreased ratio of VcFT to VcSOC1; additionally, expression of a blueberry SHORT VEGETATIVE PHASE (VcSVP) was upregulated in chilled flower buds of both transgenic and non-transgenic' "Aurora". Together with additional analysis of VcFT and VcSOC1 in the transcriptome data of other genotypes and tissues, we provide evidence to support that VcFT expression plays a significant role in promoting floral initiation and that VcSOC1 expression is a key floral activator. We thus propose a new hypothesis on blueberry flowering mechanism, of which the ratios of VcFT-to-VcSOC1 at transcript levels in the flowering pathways determine flower bud formation and bud breaking. Generally, an increased VcFT/VcSOC1 ratio or increased VcSOC1 in leaf promotes precocious flowering and flower bud formation, and a decreased VcFT/VcSOC1 ratio with increased VcSOC1 in fully chilled flower buds contributes to flower bud breaking.

Gene Editing Profiles in 94 CRISPR-Cas9 Expressing T0 Transgenic Tobacco Lines Reveal High Frequencies of Chimeric Editing of the Target Gene.

Chimeric editing is often reported in gene editing. To assess how the general chimeric editing is, we created a transgenic tobacco line carrying a marker, beta-glucuronidase gene (gusA), introduced a CRISPR-Cas9 editing vector into the transgenic tobacco line for knocking out gusA, and then investigated the gusA editing efficiencies in T0 and subsequent generations. The editing vector carried a Cas9 gene, which was driven by the cauliflower mosaic virus 35S promoter, and two guide RNAs, gRNA1 and gRNA2, which were driven by Arabidopsis U6 (AtU6) and U3 (AtU3) promoter, respectively. The two gRNAs were designed to knock out a 42-nucleotide fragment of the coding region of gusA. The editing vector was transformed into gusA-containing tobacco leaves using Agrobacterium tumefaciens-mediated transformation and hygromycin selection. Hygromycin-resistant, independent T0 transgenic lines were used to evaluate gusA-editing efficiencies through histochemical GUS assays, polymerase chain reactions (PCR), and next-generation sequencing of PCR amplicons. Profiles of targeted sequences of 94 T0 transgenic lines revealed that these lines were regenerated from non-edited cells where subsequent editing occurred and created chimeric-edited cells in these lines during or after regeneration. Two of them had the target fragment of 42 bp pairs of nucleotides removed. Detail analysis showed that on-target mutations at the AtU6-gRNA1 site and the AtU3-gRNA2 site were found in 4.3% and 77.7% of T0 transgenic lines, respectively. To overcome the issue of extremely low editing efficiencies in T0 lines, we conducted a second round of shoot induction from the chimeric line(s) to enhance the success of obtaining lines with all or most cells edited. The mutation profiles in T0 transgenic lines provide valuable information to understand gene editing in plant cells with constitutively expressed CRISPR-Cas9 and gRNAs.

Removal of a 10-kb Gret1 transposon from VvMybA1 of Vitis vinifera cv. Chardonnay.

Many white grape cultivars have a nonfunctional VvMybA1 gene due to the presence of a 10-kb Gret1 transposon in its promoter. In this study, we successfully demonstrated removal of the 10-kb Gret1 transposon and functional restoration of a VvMybA1 allele in Vitis vinifera cv. Chardonnay through transgenic expression of Cas9 and two gRNAs simultaneously targeting two junction sequences between Gret1 LTRs and VvMybA1. We generated 67 and 24 Cas9-positive vines via Agrobacterium-mediated and biolistic bombardment transformation, respectively. While the editing efficiencies were as high as 17% for the 5' target site and 65% for the 3' target site, simultaneous editing of both 5' and 3' target sites resulting in the removal of Gret1 transposon from the VvMybA1 promoter was 0.5% or less in most transgenic calli, suggesting that these calli had very limited numbers of cells with the Gret1 removed. Nevertheless, two bombardment-transformed vines, which shared the same unique editing features and were likely derived from a singly edited event, were found to have the Gret1 successfully edited out from one of their two VvMybA1 alleles. The edited allele was functionally restored based on the detection of its expression and a positive coloring assay result in leaves. Precise removal of more than a 10-kb DNA fragment from a gene locus in grape broadens the possibilities of using gene editing technologies to modify various trait genes in grapes and other plants.

Reorganization of Hydrogen Bonding in Biobased Polyamide 5,13 under the Thermo-Mechanical Field: Hierarchical Microstructure Evolution and Achieving Excellent Mechanical Performance.

The hierarchical microstructure evolution of an emerging biobased odd-odd polyamide 5,13 (PA5,13) films under the thermo-mechanical field, stepping from hydrogen bond (H-bond) arrangement to the crystalline morphology, has been investigated systematically. It is found that the reorganization of H-bonds under the thermo-mechanical field plays a crucial role in the crystallization of PA5,13. Especially, it is revealed that the crystallization process under the thermo-mechanical field develops along the chain axis direction, while lamellar fragmentation occurs perpendicular to the chain axis. Consequently, a stable and well-organized H-bond arrangement and lengthened lamellae with significant orientation have been constructed. Laudably, an impressive tensile strength of about 500 MPa and modulus of about 4.7 GPa are thus achieved. The present study could provide important guidance for the industrial-scale manufacture of high-performance biobased odd-odd PAs with long polymethylene segment in the dicarboxylic unit combined with a large difference between the polymethylene segments in the dicarboxylic and diamine units.

The coupling effect of cellulose nanocrystal and strong shear field achieved the strength and toughness balance of Polylactide.

Up to now, unbalanced mechanical properties and poor heat resistance have become two major problems of polylactic acid (PLA). In this study, the coupling between Cellulose nanocrystal (CNC) and strong shearing field formed a unique hierarchical structure. Compared with pure PLA, the tensile strength of DPIM PLA/CNC increased from 57.9 MPa to 79.6 MPa without sacrificing the toughness of PLA, and the vicat softening temperature of DPIM PLA/CNC increased from 60 °C to 155 °C. The microstructure of PLA/CNC composites was analyzed by SEM, SAXS and WAXD, and it was found that the coupling effect of CNC and strong shear flow field could significantly change the crystallization behavior of PLA. CNC could increase PLA shish length from 251 nm to 889 nm under the action of shear field. At the same time, due to this coupling effect, more PLA shish-kebab structures were induced at the interface. This special hierarchical structure composed of CNC and PLA Shish-Kebab is of great significance and can provide important guidance for achieving the balance of strength and toughness of polymer materials.

Natural cellulose supported carbon nanotubes and Fe3O4 NPs as the efficient peroxydisulfate activator for the removal of bisphenol A: An enhanced non-radical oxidation process.

Currently, many catalysts are inconvenient to separate from water, and the solvents used in the preparation process are not environmentally friendly, resulting in low recovery efficiency and secondary pollution. In this study, the magnetic and porous regenerated cellulose/carbon nanotubes/Fe3O4 nanoparticles (RC/CNTs/Fe3O4 NPs) composites were synthesized for activation of peroxydisulfate (PDS) in a green alkaline-urea system. The RC/CNTs/Fe3O4 NPs-PDS system achieved 100% removal of bisphenol A compared with CNTs (~64.6%), RC (~0%) or Fe3O4 NPs (~0%), which was closely related to the introduction of defects and functional groups, nitrogen doping and conductive networks. Interestingly, the strong interaction between CNTs and the sheath-like protective layer formed by urea on the cellulose surface promotes the introduction of nitrogen into the composites at the preparation temperature of 70 °C. Moreover, the mechanism of the system was found to be a typical non-radical pathway. Fortunately, there is no leaching of iron ions in the system, and the effects of the actual waterbody, initial pH, and different anions are negligible. The recycling and separation experiments revealed the practicality and superiority of the composite. This work provides a feasible and sustainable strategy for the application of natural cellulose-supported catalysts.

Ferrocene-Labelled Electroactive Aptamer-Based Sensors (Aptasensors) for Glycated Haemoglobin.

Glycated haemoglobin (HbA1c) is a diagnostic biomarker for type 2 diabetes. Traditional analytical methods for haemoglobin (Hb) detection rely on chromatography, which requires significant instrumentation and is labour-intensive; consequently, miniaturized devices that can rapidly sense HbA1c are urgently required. With this research, we report on an aptamer-based sensor (aptasensor) for the rapid and selective electrochemical detection of HbA1c. Aptamers that specifically bind HbA1c and Hb were modified with a sulfhydryl and ferrocene group at the 3' and 5'-end, respectively. The modified aptamers were coated through sulfhydryl-gold self-assembly onto screen printed electrodes, producing aptasensors with built in electroactivity. When haemoglobin was added to the electrodes, the current intensity of the ferrocene in the sensor system was reduced in a concentration-dependent manner as determined by differential pulse voltammetry. In addition, electrochemical impedance spectroscopy confirmed selective binding of the analytes to the aptamer-coated electrode. This research offers new insight into the development of portable electrochemical sensors for the detection of HbA1c.