RESUMEN
In this study, non-thermal plasma (NTP) was employed to modify the Cu/TiO2 adsorbent to efficiently purify H2S in low-temperature and micro-oxygen environments. The effects of Cu loading amounts and atmospheres of NTP treatment on the adsorption-oxidation performance of the adsorbents were investigated. The NTP modification successfully boosted the H2S removal capacity to varying degrees, and the optimized adsorbent treated by air plasma (Cu/TiO2-Air) attained the best H2S breakthrough capacity of 113.29 mg H2S/gadsorbent, which was almost 5 times higher than that of the adsorbent without NTP modification. Further studies demonstrated that the superior performance of Cu/TiO2-Air was attributed to increased mesoporous volume, more exposure of active sites (CuO) and functional groups (amino groups and hydroxyl groups), enhanced Ti-O-Cu interaction, and the favorable ratio of active oxygen species. Additionally, the X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) results indicated the main reason for the deactivation was the consumption of the active components (CuO) and the agglomeration of reaction products (CuS and SO42-) occupying the active sites on the surface and the inner pores of the adsorbents.
Asunto(s)
Cobre , Sulfuro de Hidrógeno , Oxidación-Reducción , Titanio , Titanio/química , Adsorción , Cobre/química , Sulfuro de Hidrógeno/química , Contaminantes Atmosféricos/química , Gases em Plasma/química , Modelos QuímicosRESUMEN
The treatment of wound inflammation is intricately linked to the concentration of reactive oxygen species (ROS) in the wound microenvironment. Among these ROS, H2O2 serves as a critical signaling molecule and second messenger, necessitating the urgent need for its rapid real-time quantitative detection, as well as effective clearance, in the pursuit of effective wound inflammation treatment. Here, we exploited a sophisticated 3D Cu2- x Se/GO nanostructure-based nanonzymatic H2O2 electrochemical sensor, which is further decorated with evenly distributed Pt nanoparticles (Pt NPs) through electrodeposition. The obtained Cu2- x Se/GO@Pt/SPCE sensing electrode possesses a remarkable increase in specific surface derived from the three-dimensional surface constructed by GO nanosheets. Moreover, the localized surface plasma effect of the Cu2- x Se nanospheres enhances the separation of photogenerated electron-hole pairs between the interface of the Cu2- x Se NPs and the Pt NPs. This innovation enables near-infrared light-enhanced catalysis, significantly reducing the detection limit of the Cu2- x Se/GO@Pt/SPCE sensing electrode for H2O2 (from 1.45 µM to 0.53µM) under NIR light. Furthermore, this biosensor electrode enables in-situ real-time monitoring of H2O2 released by cells. The NIR-enhanced Cu2- x Se/GO@Pt/SPCE sensing electrode provide a simple-yet-effective method to achieve a detection of ROS (H2O2ã-OH) with high sensitivity and efficiency. This innovation promises to revolutionize the field of wound inflammation treatment by providing clinicians with a powerful tool for accurate and rapid assessment of ROS levels, ultimately leading to improved patient outcomes.
Asunto(s)
Cobre , Peróxido de Hidrógeno , Inflamación , Nanopartículas del Metal , Platino (Metal) , Peróxido de Hidrógeno/metabolismo , Platino (Metal)/química , Cobre/química , Nanopartículas del Metal/química , Inflamación/metabolismo , Animales , Ratones , Nanoestructuras/química , Técnicas Biosensibles/métodos , Selenio/química , Humanos , Rayos Infrarrojos , Especies Reactivas de Oxígeno/metabolismo , Células RAW 264.7RESUMEN
Amyotrophic lateral sclerosis (ALS) is a neurodegenerative disease characterized by the progressive death of motor neurons (MNs). Glial cells play roles in MN degeneration in ALS. More specifically, astrocytes with mutations in the ALS-associated gene Cu/Zn superoxide dismutase 1 (SOD1) promote MN death. The mechanisms by which SOD1-mutated astrocytes reduce MN survival are incompletely understood. To characterize the impact of SOD1 mutations on astrocyte physiology, we generated astrocytes from human induced pluripotent stem cell (iPSC) derived from ALS patients carrying SOD1 mutations, together with control isogenic iPSCs. We report that astrocytes harboring SOD1(A4V) and SOD1(D90A) mutations exhibit molecular and morphological changes indicative of reactive astrogliosis when compared to isogenic astrocytes. We show further that a number of nuclear phenotypes precede, or coincide with, reactive transformation. These include increased nuclear oxidative stress and DNA damage, and accumulation of the SOD1 protein in the nucleus. These findings reveal early cell-autonomous phenotypes in SOD1-mutated astrocytes that may contribute to the acquisition of a reactive phenotype involved in alterations of astrocyte-MN communication in ALS.
RESUMEN
Metal-organic frameworks (MOFs)-related Cu materials are promising candidates for promoting electrochemical CO2 reduction to produce valuable chemical feedstocks. However, many MOF materials inevitable undergo reconstruction under reduction conditions; therefore, exploiting the restructuring of MOF materials is of importance for the rational design of high-performance catalyst targeting multi-carbon products (C2). Herein, a facile solvent process is choosed to fabricate HKUST-1 with an anionic framework (a-HKUST-1) and utilize it as a pre-catalyst for alkaline CO2RR. The a-HKUST-1 catalyst can be electrochemically reduced into Cu with significant structural reconstruction under operating reaction conditions. The anionic HKUST-1 derived Cu catalyst (aHD-Cu) delivers a FEC2H4 of 56% and FEC2 of ≈80% at -150 mA cm-2 in alkaline electrolyte. The resulting aHD-Cu catalyst has a high electrochemically active surface area and low coordinated sites. In situ Raman spectroscopy indicates that the aHD-Cu surface displays higher coverage of *CO intermediates, which favors the production of hydrocarbons.
RESUMEN
Metallic pollutants can have harmful impacts on ant morphology and physiology. We studied the occurrence of labial gland disease in Camponotus japonicus from two polluted areas (traffic pollution and industrial pollution) and one non-polluted area. We further analyzed the metal levels (Al, As, Cd, Co, Cr, Cu, Fe, Hg, Mn, Ni, Pb and Zn) and morphological characteristics (head width, body mass, and other morphological traits) of both diseased and healthy workers. Our results showed that labial gland disease was only present in polluted areas, indicating that pollution stress makes ants more vulnerable to infections. Our research revealed that diseased ants in polluted areas accumulate higher levels of metals in their bodies and have lower dry weight and residual body mass compared to healthy ants in non-polluted environments, negatively impacting their development. We evaluated the importance of these elements and found that Cu has the greatest impact on the health risk of C. japonicus. Our study underscores the significant impact of environmental pollution on ant morphology and physiology and raises concerns about the broader ecological implications.
RESUMEN
We have developed an innovative mesoporous nanocatalyst by carefully attaching a 2-aminothiophenol-Cu complex onto functionalized MCM-41. This straightforward synthesis process has yielded a versatile nanocatalyst known for its outstanding efficiency, recyclability, and enhanced stability. The structural integrity of the nanocatalyst was comprehensively analyzed using an array of techniques, including BET (Brunauer-Emmett-Teller) for surface area measurement, ICP (Inductively Coupled Plasma) for metal content determination, EDS (Energy-Dispersive X-ray Spectroscopy) for elemental mapping, XRD (X-ray Diffraction) for crystalline structure elucidation, SEM (Scanning Electron Microscopy), EMA (Elemental Mapping Analysis), TEM (Transmission Electron Microscopy), TGA (Thermogravimetric Analysis), FT-IR (Fourier Transform Infrared Spectroscopy), AFM (Atomic Force Microscopy), and CV (cyclic voltammetry). Subsequently, the catalytic properties of the newly developed MCM-41-CPTEO-2-aminothiophenol-Cu catalyst was evaluated in the synthesis of biphenyls, demonstrating outstanding yields through a Suzuki coupling reaction between phenylboronic acid and aryl halides. Importantly, this reaction was conducted in an environmentally friendly medium. Note the remarkable recyclability of the catalyst, proving its sustainability over six cycles with minimal loss in activity additionally hot filtration test was prepared to examine the stability of this nanocatalyst. This outstanding feature emphasizes the catalyst's potential for long-term, environmentally conscious catalytic applications.
RESUMEN
With excessive Mn(â ¡) and Cu(â ¡) pollution in aquatic environments posing potential health risks to inhabitants, the emergence of carbon capture, utilization and storage (CCUS) technology has promoted the improvement of heavy metal remediation technologies. Using hydrothermal sediment as a crystal seed, rhamnolipid was used to mediate biomimetic mineralization to prepare hydrated magnesium carbonate (HMC) composites to enhance the Mn(â ¡)/Cu(â ¡) adsorption performance of alginate hydrogels. Hydrothermal sediment is beneficial for accelerating biomimetic mineralization, while rhamnolipid can induce a crystalline phase transformation from dypingite to nesquehonite. The addition of sediment significantly enhanced the compressive mechanical properties and thermal stability of the hydrogels. The adsorption performances of the nesquehonite and dypingite hydrogels were better for Mn(II) and Cu(II), respectively. An increase in the amount of sediment improved the adsorption of Cu(II) by the hydrogels appropriately, resulting in stronger selectivity for Cu(II). The adsorption of Mn(II) and Cu(II) on the hydrogel beads was thermodynamically spontaneous. The inhibitory effects of sodium dodecyl benzene sulfonate (SDBS), fulvic acid (FA) and alginate on Cu(II) adsorption were more obvious than those of bovine serum albumin (BSA). Both the complexation of functional groups on alginate and mineralization by HMC participated in the adsorption of Mn(II) and Cu(II).
RESUMEN
Single crystals of the mol-ecular compound, {Cu20Ir6Cl8(C21H24N2)6(C4H4N2)3]·3.18CH3OH or [({Cu10Ir3}Cl4(IMes)3(pyrazine))2(pyrazine)]·3.18CH3OH [where IMes is 1,3-bis-(2,4,6-trimethylphen-yl)imidazol-2-yl-idene], with a unique heterometallic cluster have been prepared and the structure revealed using single-crystal X-ray diffraction. The mol-ecule is centrosymmetric with two {Cu10Ir3} cores bridged by a pyrazine ligand. The polymetallic cluster contains three stabilizing N-heterocyclic carbenes, four Cl ligands, and a non-bridging pyrazine ligand. Notably, the Cu-Ir core is arranged in an unusual shape containing 13 vertices, 22 faces, and 32 sides. The atoms within the trideca-metallic cluster are arranged in four planes, with 2, 4, 4, 3 metals in each plane. Ir atoms are present in alternate planes with an Ir atom featuring in the peripheral bimetallic plane, and two Ir atoms featuring on opposite sides of the non-adjacent tetra-metallic plane. The crystal contains two disordered methanol solvent mol-ecules with an additional region of non-modelled electron density corrected for using the SQUEEZE routine in PLATON [Spek (2015 â¸). Acta Cryst. C71, 9-18]. The given chemical formula and other crystal data do not take into account the unmodelled methanol solvent mol-ecule(s).
RESUMEN
Widespread ecosystem degradation from noxious substances like industrial waste, toxic dyes, pesticides, and herbicides poses serious environmental risks. For remediation of these hazardous problems, present study introduces an innovative Cu-doped Ce2Zr2O7 nano-photocatalyst, fabricated via a simple, eco-friendly hydrothermal method, designed to degrade toxic textile dye methylene blue. Harnessing Cu doping for pyrochlore Ce2Zr2O7, structure engineering carried out through a hydrothermal synthesis method to achieve superior photocatalytic performance, addressing limitations of rapid charge carrier recombination in existing photocatalysts. Photoluminescence analysis showed that doped pyrochlore slows charge carrier recombination, boosting dye degradation efficiency. UV-Visible analysis demonstrated an impressive 96 % degradation of methylene blue by Cu-doped Ce2Zr2O7 within 50 min, far exceeding the performance of pristine materials. Trapping experiments clarified the charge transfer mechanism, deepening our understanding of the photocatalytic process. These findings highlight the potential for developing innovative, highly efficient photocatalysts for environmental remediation, offering sustainable solutions to combat pollution. This study not only addresses the limitations of existing photocatalysts but also opens new avenues for enhancing photocatalytic performance through strategic material design.
RESUMEN
In this work, up- and down-conversion dual-emission CDs without rare-earth (UD D-CDs) were synthesized using RhB and 1,4-Diaminoanthraquinone as precursors. The synthesized UD D-CDs exhibited dual emissions at 496 and 580 nm under 260 and 865 nm excitation, respectively. The fluorescence emission mechanism, including contributions from carbon nuclei, surface states, molecular states, and internal defect states, was discussed through the separation and purification of UD D-CDs. Based on the interaction between UD D-CDs and copper ions (Cu2+), a dual-mode ratio fluorescence probe was developed to detect and quantify Cu2+. The up-conversion ratio fluorescent probe shows a linear range of 0.0500-15.0 µM, with a detection limit as low as 2.76 nM. This method has been successfully applied to detecting Cu2+ in human serum and has potential applications in biochemical analysis and biological imaging. The successful preparation of up-conversion fluorescent carbon dots without rare earth elements and the ability to perform low-damage detection in high-background biological samples provide a new approach to constructing non-rare earth up-conversion probes.
RESUMEN
Copper (Cu) is a co-factor for several essential metabolic enzymes. Disruption of Cu homeostasis results in genetic diseases such as Wilson's disease. Here, we show that the zinc transporter 1 (ZnT1), known to export zinc (Zn) out of the cell, also mediates Cu2+ entry into cells and is required for Cu2+-induced cell death, cuproptosis. Structural analysis and functional characterization indicate that Cu2+ and Zn2+ share the same primary binding site, allowing Zn2+ to compete for Cu2+ uptake. Among ZnT members, ZnT1 harbors a unique inter-subunit disulfide bond that stabilizes the outward-open conformations of both protomers to facilitate efficient Cu2+ transport. Specific knockout of the ZnT1 gene in the intestinal epithelium caused the loss of Lgr5+ stem cells due to Cu deficiency. ZnT1, therefore, functions as a dual Zn2+ and Cu2+ transporter and potentially serves as a target for using Zn2+ in the treatment of Wilson's disease caused by Cu overload.
RESUMEN
The acidic electrocatalytic conversion of CO2 to multi-carbon (C2+) oxygenates is of great importance in view of enhancing carbon utilization efficiency and generating products with high energy densities, but suffering from low selectivity and activity. Herein, we synthesized Ag-Cu alloy catalyst with highly rough surface, by which the selectivity to C2+ oxygenates can be greatly improved. In a strongly acidic condition (pH=0.75), the maximum C2+ products Faradaic efficiency (FE) and C2+ oxygenates FE reach 80.4% and 56.5% at -1.9 V versus reversible hydrogen electrode, respectively, with a ratio of FEC2+ oxygenates to FEethylene up to 2.36. At this condition, the C2+ oxygenates partial current density is as high as 480 mA cm-2. The in situ Raman measurements and control experiments indicate that the high generation of C2+ oxygenates over the catalyst originates from its large surface roughness and Ag alloying.
RESUMEN
Background: Copper oxide (Cu2O) nanoparticles (CO NPs) are in extensive use during our everyday life as antimicrobial agent, lubricant, in manufacturing electrodes of lithium ion batteries as well as for photo catalytic degradation of organic pollutants. Due to extensive and diverse use Cu2O NPs, they are likely to accumulate in the environment and to affect the live forms. Present investigation was aimed to report the biocompatibility of CO NPs in Wistar rats in sex specific manner. CO NPs, having average diameter of 14.06 nm, were synthesized by co-precipitation method and scanning electron microscopy and X ray diffraction were used for their characterization. Methods: For 14 consecutive days, Wistar rats (6 weeks old) of both sexes were intraperitoneally injected with 10 mg/mL saline/Kg body weight of CO NPs, while the control groups intraperitoneally received saline solution for same duration. Behavioral tests (open field and novel object recognition), complete blood count, selected biomarkers of oxidative stress and Copper concentration in brain and liver were determined in all subjects. Results: High mortality rates [male 40% and female 60%] were observed in rats exposed to CO NPs. A sever decrease in body weight was also observed in both male and female rats exposed to CO NPs. Female rats treated with CO NPs spent significantly more time with novel object as compared to control [P = 0.05] during second trial of novel object test. CO NPs treated female rats had higher mean corpuscular hemoglobin [P < 0.001] levels and Copper concentration in liver [P = 0.04] than control. Male rats exposed to CO NPs had significantly higher mean corpuscular volume [P = 0.02] and superoxide dismutase [SOD] [P = 0.04] in lungs than their control group. All other studied parameters non significantly varied upon comparison between CO NPs treated and untreated rats of both sex. Conclusion: In conclusion, we are reporting that intraperitoneal injections of CO NPs for 14 days can disturb complete blood count and biomarkers of oxidative stress in lungs of Wistar rats.
RESUMEN
Chitosan (CS) is commonly used as an adsorbent for removing Cu(II) from water, but it has drawbacks such as solubility in dilute acid, difficulty in recycling in powder form, and short service life. This study utilized sodium alginate (SA) as a gel carrier to encapsulate CS, combined with silicon dioxide (SiO2) to improve mechanical stability. The preparation of CS/SA/SiO2 (SSC1.0) involved physical blending, CaCl2 cross-linking, and freeze-drying. Characterization methods such as SEM-EDS, FTIR, BET, and XRD were used to analyze the structural composition of SSC1.0. The material exhibited a folded surface, porous internal cross-section, nitrogen/oxygen-containing functional groups, and thermal stability in high temperatures and various aqueous environments. The adsorption performance of SSC1.0 on Cu(II) was evaluated under different conditions, showing a maximum adsorption capacity of 47.50 mg/g. The material maintained a removal rate above 70 % after 5 cycles. SSC1.0 also showed the highest removal rate of Cu(II) when applied to mine wastewater treatment. Adsorption modeling indicated that the process was driven by chemical reactions and was spontaneous and heat-absorbing.'
RESUMEN
Excessive ammonia nitrogen can potentially compromise the safety of drinking water. Therefore, developing a rapid and simple detection method for ammonia nitrogen in drinking water is of great importance. Nickel-copper hydroxides exhibit strong catalytic capabilities and are widely applied in ammonia nitrogen oxidation. In this study, a self-supported electrode made of nickel-copper carbonate hydroxide was synthesized on a carbon cloth collector via a straightforward one-step hydrothermal method for rapid ammonia nitrogen detection in water. It exhibits sensitivities of 3.9 µA µM-1 cm-2 and 3.13 µA µM-1 cm-2 within linear ranges of 1 µM to 100 µM and 100 µM to 400 µM, respectively, using a simple and rapid i-t method. The detection limit is as low as 0.62 µM, highlighting its excellent anti-interference properties against various anions and cations. The methodology's simplicity and effectiveness suggest broad applicability in water quality monitoring and environmental protection, particularly due to its significant cost-effectiveness.
RESUMEN
Chromium-plated diamond/copper composite materials, with Cr layer thicknesses of 150 nm and 200 nm, were synthesized using a vacuum hot-press sintering process. Comparative analysis revealed that the thermal conductivity of the composite material with a Cr layer thickness of 150 nm increased by 266%, while that with a Cr layer thickness of 200 nm increased by 242%, relative to the diamond/copper composite materials without Cr plating. This indicates that the introduction of the Cr layer significantly enhanced the thermal conductivity of the composite material. The thermal properties of the composite material initially increased and subsequently decreased with rising sintering temperature. At a sintering temperature of 1050 °C and a diamond particle size of 210 µm, the thermal conductivity of the chromium-plated diamond/copper composite material reached a maximum value of 593.67 Wâm-1âK-1. This high thermal conductivity is attributed to the formation of chromium carbide at the interface. Additionally, the surface of the diamond particles in contact with the carbide layer exhibited a continuous serrated morphology due to the interface reaction. This "pinning effect" at the interface strengthened the bonding between the diamond particles and the copper matrix, thereby enhancing the overall thermal conductivity of the composite material.
RESUMEN
In this paper, the effect of thermomechanical treatment process on the hardening behavior, grain microstructure, precipitated phase, and tensile mechanical properties of the new high-strength and high-ductility Al-10.0Zn-3.0Mg-2.8Cu alloy was studied, and the optimal thermomechanical treatment process was established. The strengthening and toughening mechanisms were revealed, which provided technical and theoretical guidance for the engineering application of this kind of high strength-ductility aluminum alloy. Al-10.0Zn-3.0Mg-2.8Cu alloy cylindrical parts with external longitudinal reinforcement were prepared by a composite extrusion deformation process (reciprocal upsetting + counter-extrusion) with a true strain up to 2.56, and the organizational evolution of the alloys during the extrusion deformation process and the influence of pre-stretching treatments on the subsequent aging precipitation behaviors and mechanical properties were investigated. The results show that firstly, the large plastic deformation promotes the fragmentation of coarse insoluble phases and the occurrence of dynamic recrystallization, which results in the elongation of the grains along the extrusion direction, and the volume fraction of recrystallization reaches 42.4%. Secondly, the kinetic study showed that the decrease in the activation energy of precipitation increased the nucleation sites, which further promoted the diffuse distribution of the second phase in the alloy and a higher number of nucleation sites, while limiting the coarsening of the precipitated phase. When the amount of pre-deformation was increased from 0% to 2%, the size of the matrix precipitated phase decreased from 5.11 µm to 4.1 µm, and when the amount of pre-deformation was increased from 2% to 7%, the coarsening of the matrix precipitated phase took place, and the size of the phase increased from 4.1 µm to 7.24 µm. The finalized heat treatment process for the deformation of the aluminum alloy tailframe was as follows: solution (475 °C/3 h) + 2% pre-stretching + aging (120 °C/24 h), at which the comprehensive performance of the alloy was optimized, with a tensile strength of 634.2 MPa, a yield strength of 571.0 MPa, and an elongation of 15.2%. The alloy was strengthened by both precipitation strengthening and dislocation strengthening. After 2% pre-stretching, the fracture surface starts to be dominated by dense tough nest structure, and most of them are small tough nests, and small and dense tough nests are the main reason for the increase in alloy toughness after 2% pre-stretching deformation.
RESUMEN
In the field of nucleic acid amplification assays, developing enzyme-free, easy-to-use, and highly sensitive amplification approaches remains a challenge. In this work, we synthesized a heterogeneous Cu2O nanocatalyst (hnCu2O) with different particle sizes and shapes, which was used for developing enzyme- and label-free nucleic acid amplification methods based on the nucleic acid-templated azide-alkyne cycloaddition (AAC) reaction catalyzed by hnCu2O. The hnCu2O exhibited size- and shape-dependent catalytic activity, with smaller sizes and spherical-like shapes exhibiting superior activity. Spherical-like hnCu2O (61 ± 8 nm) not only achieved a ligation yield of up to 84.2 ± 3.9 % in 3 min but also exhibited faster kinetics in the nucleic acid-templated hnCu2O-catalyzed AAC reaction, with a high reaction rate of 0.65 min-1 and a half-life of 1.07 ± 0.09 min. Based on this result, we developed nucleic acid-templated click ligation linear amplification reaction (NA-CLLAR) and nucleic acid-templated click ligation exponential amplification reaction (NA-CLEAR) approach. By combining the recognition (complementary to the target sequence) and signal output (split G-quadruplex sequence) elements into a DNA probe, the NA-CLLAR and NA-CLEAR fluorescence assays achieved highly specific detection of target nucleic acids, with a detection limit of 2.8 aM based on G-quadruplex-enhanced fluorescence. This work is a valuable reference and will inspire researchers to design enzyme-free nucleic acid signal amplification strategies by developing different types of Cu(I) catalysts with improved catalytic activity.
RESUMEN
In spite of extensive research and appreciable progress, in aqueous zinc-ion batteries, Zn metal anode is struggling with low Zn utility and poor cycling stability. In this study, a 3D "electrochemical welding" composite electrode is designed by introduction of ZnO/C nanofibers film to copper foils as an anode according to pre-electrodeposition active Zn (Zn@ZnO/C-Cu). The flow of Zn2+ through carbon fiber layer is regulated by zincophilic ZnO, promoting homogeneous diffusion of Zn2+ to Cu foil. In subsequent Zn deposition/stripping processes, the hydrophobicity of ZnO/C fiber layer reduces water at the interface of Zn@ZnO/C-Cu and results in uniform electric field significant suppressing growth of Zn dendritic and side reactions. Thus, pre-electrodeposition active Zn electrochemical welds ZnO/C nanofibers and Cu foil collectively provide stable charge/electron transfer and stripping/plating of Zn with low polarization and excellent cycling performance. The assembled symmetrical batteries exhibit stable cycling performance for over 470 h under 20% utilization of Zn at 5 mA cm-2, and an average coulombic efficiency of 99.9% at low negative/positive capacity ratio (N/P = 1) after 1000 cycles in the Zn@ZnO/C-Cu||Na2V6O16·1.5H2O full cell.
RESUMEN
Iodometric and iodimetric titrations represent a prevailing technique to determine the concentration of Cu2+ ions in aqueous solutions; However, their utilization in electrochemical energy storage has been overlooked due to the poor reversibility between CuI and Cu2+ related to the shuttling effect of I3- species. In this work, we developed a 4A zeolite separator capable of suppressing the free shuttling of I3- ions, thus achieving a record-high capacity retention of 95.7% upon 600 cycles. Theoretical and experimental studies reveal that the negatively charged zeolite can effectively impede the approach and penetration of I3- ions, as a result of electrostatic interaction between them. To explore the practical potential, a hybrid cell of Znâ¥I2 consisting of Cu2+ redox agent has been assembled with a discharge capacity of 356 mA h g-1. The cell affords a specific energy of 443 W h kg-1 based on I2, or 193 W h kg-1 based on both electrodes. This work offers insight on the energy utilization of the iodometric reactions and advocates a Cu2+-mediated cell design that could potentially double the capacity and energy of conventional aqueous battery systems.