Impact of photo-oxidation on long term storage of affinity chromatography media used in multi-specific antibody manufacturing processes.

Large scale manufacture of complex biotherapeutic formats such as multi-specific antibodies can require development of custom biomanufacturing platforms, particularly for purification processes. Substantial advances in affinity chromatography media have allowed monoclonal antibody-like processes for these formats, and simplified process development to enable fast speed to the clinic. Thorough assessment of chromatography media performance and stability is critical to ensure robust operation and consistent product quality over repeated cycles throughout its lifetime. However, evaluation of repeated cycling and extended storage for chromatography media is resource consuming, which typically delays rigorous study to later development stages and often is acquired through increased operational experience. These areas can present quality risks if not properly understood. In this work, a class of affinity chromatography media employing camelid antibody-fragment ligands were evaluated for extended storage in benzyl alcohol solution as an alternative to ethanol storage. Initial laboratory studies revealed resin discoloration after 12 months of exposure to ambient light at room temperature. Resin photo-stress studies confirmed light exposure as the root cause, with benzyl alcohol storage conditions producing a substantially greater degree of discoloration compared to ethanol. Extreme photo-stress over the course of 7 days was also found to negatively impact resin dynamic binding capacities, with more severe declines observed with benzyl alcohol storage conditions. Binding capacity loss of 54 % was observed for photo-stressed CaptureSelect Kappa XP compared to control conditions. Addition of antioxidants reduced or eliminated resin discoloration during photo-stress, indicating that benzyl alcohol storage accelerates photo-oxidation of the affinity chromatography ligands. The addition of l-methionine to benzyl alcohol solution prevented resin discoloration and maintained a dynamic binding capacity of 41 g/L for CaptureSelect Kappa XP even after extreme photo-stress. Of practical importance, a study of LambdaFabSelect resin used and stored in benzyl alcohol solution, under recommended conditions (2-8 °C storage, protected from light) in an internal GMP facility over a period of three years, showed no impact to resin color, performance, or product quality.

A pH-dependent shift of redox cofactor specificity in a benzyl alcohol dehydrogenase of aromatoleum aromaticum EbN1.

We characterise a reversible bacterial zinc-containing benzyl alcohol dehydrogenase (BaDH) accepting either NAD+ or NADP+ as a redox cofactor. Remarkably, its redox cofactor specificity is pH-dependent with the phosphorylated cofactors favored at lower and the dephospho-forms at higher pH. BaDH also shows different steady-state kinetic behavior with the two cofactor forms. From a structural model, the pH-dependent shift may affect the charge of a histidine in the 2'-phosphate-binding pocket of the redox cofactor binding site. The enzyme is phylogenetically affiliated to a new subbranch of the Zn-containing alcohol dehydrogenases, which share this conserved residue. BaDH appears to have some specificity for its substrate, but also turns over many substituted benzyl alcohol and benzaldehyde variants, as well as compounds containing a conjugated C=C double bond with the aldehyde carbonyl group. However, compounds with an sp3-hybridised C next to the alcohol/aldehyde group are not or only weakly turned over. The enzyme appears to contain a Zn in its catalytic site and a mixture of Zn and Fe in its structural metal-binding site. Moreover, we demonstrate the use of BaDH in an enzyme cascade reaction with an acid-reducing tungsten enzyme to reduce benzoate to benzyl alcohol. KEY POINTS: •Zn-containing BaDH has activity with either NAD + or NADP+ at different pH optima. •BaDH converts a broad range of substrates. •BaDH is used in a cascade reaction for the reduction of benzoate to benzyl alcohol.

Oxyfunctionalization of Benzylic C-H Bonds of Toluene Mediated by Covalently Anchored Co-Schiff Bases.

Oxyfunctionalization of toluene to value-added benzaldehyde, benzyl alcohol and benzoic acid is of great significance. In this work, Co-Schiff bases were immobilized on commercial silica gel by covalent anchoring, and resulting catalysts were used to catalyze the oxidation of toluene in the presence of the cocatalyst N-hydroxyphthalimide (NHPI). The catalysts exhibited excellent textural and structural properties, reliable bonding and a predomination of the cobaltous ions. The catalyst synthesized by diethylamino salicylaldehyde (EASA) possessed a grafting density of 0.14 mmol/g and exhibited a toluene conversion of 37.5%, with predominant selectivities to benzaldehyde, benzyl alcohol and benzoic acid under solvent-free conditions. It is concluded that the effect of ligands on their catalytic performance might be related to their electron-donating or -withdrawing properties.

Molecular Mechanism of Antimicrobial Excipient-Induced Aggregation in Parenteral Formulations of Peptide Therapeutics.

Antimicrobial preservatives are used as functional excipients in multidose formulations of biological therapeutics to destroy or inhibit the growth of microbial contaminants, which may be introduced by repeatedly administering doses. Antimicrobial agents can also induce the biophysical instability of proteins and peptides, which presents a challenge in optimizing the drug product formulation. Elucidating the structural basis for aggregation aids in understanding the underlying mechanism and can offer valuable knowledge and rationale for designing drug substances and drug products; however, this remains largely unexplored due to the lack of high-resolution characterization. In this work, we utilize solution nuclear magnetic resonance (NMR) as an advanced biophysical tool to study an acylated 31-residue peptide, acyl-peptide A, and its interaction with commonly used antimicrobial agents, benzyl alcohol and m-cresol. Our results suggest that acyl-peptide A forms soluble octamers in the aqueous solution, which tumble slowly due to an increased molecular weight as measured by diffusion ordered spectroscopy and 1H relaxation measurement. The addition of benzyl alcohol does not induce aggregation of acyl-peptide A and has no chemical shift perturbation in 1H-1H NOESY spectra, suggesting no detectable interaction with the peptide. In contrast, the addition of 1% (w/v) m-cresol results in insoluble aggregates composed of 25% (w/w) peptides after a 24-hour incubation at room temperature as quantified by 1H NMR. Interestingly, 1H-13C heteronuclear single-quantum coherence and 1H-1H total correlation experiment spectroscopy have identified m-cresol and peptide interactions at specific residues, including Met, Lys, Glu, and Gln, suggesting that there may be a combination of hydrophobic, hydrogen bonding, and electrostatic interactions with m-cresol driving this phenomenon. These site-specific interactions have promoted the formation of higher-order oligomerization such as dimers and trimers of octamers, eventually resulting in insoluble aggregates. Our study has elucidated a structural basis of m-cresol-induced self-association that can inform the optimized design of drug substances and products. Moreover, it has demonstrated solution NMR as a high-resolution tool to investigate the structure and dynamics of biological drug products and provide an understanding of excipient-induced peptide and protein aggregation.

Synthesis of Acid Free Benzaldehyde by Highly Selective Oxidation of Benzyl Alcohol Over Recyclable Supported Palladium Catalyst.

AIM AND OBJECTIVES: This research work deals with the highly selective oxidation of benzyl alcohol to benzaldehyde by palladium doped graphene oxide catalyst, which was synthesized by a modified Hummer's method. The effect of reaction parameters like temperature, time and catalyst loading were studied. It was found that fine-tuning of reaction temperature and presence of a small amount of benzyl alcohol in a product prevented the undesirable formation of benzoic acid crystals, which form on auto-oxidation of benzaldehyde. Benzoic acid or substituted benzoic acid formation was hindered by the presence of < 2% benzyl alcohol at a reaction temperature of 50˚C, which was further supported by palladium doped graphene oxide catalyst. MATERIALS AND METHODS: Modified Hummer's method was used for the synthesis of graphene oxide and palladium doped graphene oxide was synthesized by in-situ method in which graphene oxide dispersed in 20mL of distilled water was ultrasonicated for 2h. Palladium solution was added and it was further ultrasonicated for 30min for homogeneous deposition of palladium on a graphene oxide support. To this, 2 mL of sodium borohydride solution was added and stirred at room temperature for 4h. The resulting solution was centrifuged, and the residue was dried at 60°C for 12 h. RESULTS: The morphological characteristics and the functional groups of supported catalysts were characterized by X-ray diffraction, Field emission scanning spectroscopy, and Fourier transform infrared spectroscopy. The produced benzaldehyde was characterized by gas chromatography. CONCLUSION: PdGO catalyst was prepared using sodium borohydride as a reducing agent by modified Hummer's method and utilized for the oxidation of benzyl alcohol to benzaldehyde. A maximum conversion of 89% and selectivity of 99% were obtained and the catalyst could be reused up to five times without any compromise on conversion and selectivity.

Benzyl alcohol inhibits carbonic anhydrases by anchoring to the zinc coordinated water molecule.

Up to date alcohols have been scarcely investigated as carbonic anhydrase (CA) inhibitors. To get more insights into the CA inhibition properties of this class of molecules, in this paper, by means of inhibition assays and X-ray crystallographic studies we report a detailed characterization of the CA inhibition properties and the binding mode to human CA II of benzyl alcohol. Results show that, although possessing a very simple scaffold, this molecule acts as a micromolar CA II inhibitor, which anchors to the enzyme active site by means of an H-bond interaction with the zinc bound solvent molecule. Taken together our results clearly indicate primary alcohols as a class of CA inhibitors that deserve to be more investigated.

Source of Early Regenerating Axons in Lamprey Spinal Cord Revealed by Wholemount Optical Clearing with BABB.

Many studies of axon regeneration in the lamprey focus on 18 pairs of large identified reticulospinal (RS) neurons, whose regenerative abilities have been individually quantified. Their axons retract during the first 2 weeks after transection (TX), and many grow back to the site of injury by 4 weeks. However, locomotor movements begin before 4 weeks and the lesion is invaded by axons as early as 2 weeks post-TX. The origins of these early regenerating axons are unknown. Their identification could be facilitated by studies in central nervous system (CNS) wholemounts, particularly if spatial resolution and examination by confocal microscopy were not limited by light scattering. We have used benzyl alcohol/benzyl benzoate (BABB) clearing to enhance the resolution of neuronal perikarya and regenerated axons by confocal microscopy in lamprey CNS wholemounts, and to assess axon regeneration by retrograde and anterograde labeling with fluorescent dye applied to a second TX caudal or rostral to the original lesion, respectively. We found that over 50% of the early regenerating axons belonged to small neurons in the brainstem. Some propriospinal neurons located close to the TX also contributed to early regeneration. The number of early regenerating propriospinal neurons decreased with distance from the original lesion. Descending axons from the brainstem were labeled anterogradely by application of tracer to a second TX close to the spinal-medullary junction. This limited contamination of the data by regenerating spinal axons whose cell bodies are located rostral or caudal to the TX and confirmed the regeneration of many small RS axons as early as 2 weeks post-TX. Compared with the behavior of axotomized giant axons, the early regenerating axons were of small caliber and showed little retraction, probably because they resealed rapidly after injury.

Nanoporous Crystalline Composite Aerogels with Reduced Graphene Oxide.

High-porosity monolithic composite aerogels of syndiotactic polystyrene (sPS) and poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) containing reduced graphene oxide (r-GO) were prepared and characterized. The composite aerogels obtained by supercritical carbon dioxide (scCO2) extraction of sPS/r-GO and PPO/r-GO gels were characterized by a fibrillar morphology, which ensured good handling properties. The polymer nanoporous crystalline phases obtained within the aerogels led to high surface areas with values up to 440 m2 g-1. The role of r-GO in aerogels was studied in terms of catalytic activity by exploring the oxidation capacity of composite PPO and sPS aerogels toward benzyl alcohol in diluted aqueous solutions. The results showed that, unlike sPS/r-GO aerogels, PPO/r-GO aerogels were capable of absorbing benzyl alcohol from the diluted solutions, and that oxidation of c.a. 50% of the sorbed benzyl alcohol molecules into benzoic acid occurred.

SAR:s for the Antiparasitic Plant Metabolite Pulchrol. 1. The Benzyl Alcohol Functionality.

Pulchrol (1) is a natural benzochromene isolated from the roots of Bourreria pulchra, shown to possess potent antiparasitic activity towards both Leishmania and Trypanozoma species. As it is not understood which molecular features of 1 are important for the antiparasitic activity, several analogues were synthesized and assayed. The ultimate goal is to understand the structure-activity relationships (SAR:s) and create a QSAR model that can be used for the development of clinically useful antiparasitic agents. In this study, we have synthesized 25 2-methoxy-6,6-dimethyl-6H-benzo[c]chromen analogues of 1 and its co-metabolite pulchral (5a), by semi-synthetic procedures starting from the natural product pulchrol (1) itself. All 27 compounds, including the two natural products 1 and 5a, were subsequently assayed in vitro for antiparasitic activity against Trypanozoma cruzi, Leishmania brasiliensis and Leishmania amazoniensis. In addition, the cytotoxicity in RAW cells was assayed, and a selectivity index (SI) for each compound and each parasite was calculated. Several compounds are more potent or equi-potent compared with the positive controls Benznidazole (Trypanozoma) and Miltefosine (Leishmania). The compounds with the highest potencies as well as SI-values are esters of 1 with various carboxylic acids.

Direct Synthesis of Chain-end-functionalized Poly(3-hexylthiophene) without Protecting Groups Using a Zincate Complex.

Chain-end-functionalized poly(3-hexylthiophene)s (P3HTs) with benzyl alcohol (─PhCH2 OH), phenol (─PhOH), and benzoic acid (─PhCOOH) groups are directly synthesized based on the Negishi catalyst-transfer polycondensation method utilizing the zincate complex of t Bu4 ZnLi2 . In this system, neither protection nor deprotection steps are required, and also providing a living polymerization system to control the molecular weight while maintaining a low molar mass dispersity (ÐM ) of the obtained P3HT derivatives. Indeed, the chain-end-functionalized P3HTs can be synthesized along with controlled number-average molecular weights (Mn = 5100-20 000), low ÐM (1.06-1.14), and high chain-end functionality (Fn = 46-86%). The Fn values for the alcohol and phenol groups are found to be high (86% for ─PhCH2 OH and 71% for ─PhOH based on 1 H NMR, respectively), as also confirmed by matrix-assisted laser desorption/ionization time of flight mass spectroscopy. The easily synthesizable chain-end-functionalized P3HTs will be applicable for the facile synthesis of block and branched polymers containing P3HT as well as its related semiconducting polymer segments.

Identification of the Volatile Components of Galium verum L. and Cruciata leavipes Opiz from the Western Italian Alps.

The chemical composition of the volatile fraction from Galium verum L. (leaves and flowers) and Cruciata laevipes Opiz (whole plant), Rubiaceae, was investigated. Samples from these two plant species were collected at full bloom in Val di Susa (Western Alps, Turin, Italy), distilled in a Clevenger-type apparatus, and analyzed by GC/FID and GC/MS. A total of more than 70 compounds were identified, making up 92%-98% of the total oil. Chemical investigation of their essential oils indicated a quite different composition between G. verum and C. laevipes, both in terms of the major constituents and the dominant chemical classes of the specialized metabolites. The most abundant compounds identified in the essential oils from G. verum were 2-methylbenzaldheyde (26.27%, corresponding to 11.59 µg/g of fresh plant material) in the leaves and germacrene D (27.70%; 61.63 µg/g) in the flowers. C. laevipes essential oils were instead characterized by two sesquiterpenes, namely ß-caryophyllene (19.90%; 15.68 µg/g) and trans-muurola-4(15),5-diene (7.60%; 5.99 µg/g); two phenylpropanoids, benzyl alcohol (8.30%; 6.71 µg/g), and phenylacetaldehyde (7.74%; 6.26 µg/g); and the green-leaf alcohol cis-3-hexen-1-ol (9.69%; 7.84 µg/g). The ecological significance of the presence of such compounds is discussed.

Ionic-liquid-modified CMK-3 as a support for the immobilization of molybdate ions (MoO42-): Heterogeneous nanocatalyst for selective oxidation of sulfides and benzylic alcohols.

A nanometric carbon CMK-3 modified with octylimidazolium ionic liquid and MoO42- as a new hybrid catalyst was synthesized. The study is the first to report a successful immobilization of MoO4= on the CMK-3/OctIm as a hybrid nanocatalyst. A variety of analytical methods were utilized to determine the properties of the structure and morphology of the synthesized nanocatalyst [CMK-3/Im/MoO42-]. The analytical techniques were transmission electron microscopy (TEM), scanning electron microscope (SEM), energy-dispersive X-ray spectroscopy (EDS), inductively coupled plasma (ICP), X-ray diffraction (XRD), N2 isotherms (BET), IR spectroscopy and thermogravimetric analysis (TGA). CMK-3/OctIm/MoO42- hybrid catalyst demonstrated a considerable catalytic activity. It is a recyclable nanocatalyst that is utilized to chemoselectively oxidize different types of sulfides to the corresponding sulfoxides and benzylic alcohols to aldehydes using the green oxidant, hydrogen peroxide (H2O2) in high-yields. With a little leaching and variation in activity, it is possible to recover and reuse the catalyst frequently. A combination of molybdate anion and the CMK-3 order mesoporous carbon resulted in an improvement in the performance of catalysis and ease of separation for the reaction procedure.

Characterization of a Self-Sufficient Cytochrome P450 Monooxygenase from Deinococcus apachensis for Enantioselective Benzylic Hydroxylation.

A self-sufficient cytochrome P450 monooxygenase from Deinococcus apachensis (P450DA) was identified and successfully overexpressed in Escherichia coli BL21(DE3). P450DA would be a member of the CYP102D subfamily and assigned as CYP102D2 according to the phylogenetic tree and sequence alignment. Purification and characterization of the recombinant P450DA indicated both NADH and NADPH could be used by P450DA as a reducing cofactor. The recombinant E. coli (P450DA) strain was functionally active, showing excellent enantioselectivity for benzylic hydroxylation of methyl 2-phenylacetate. Further substrate scope studies revealed that P450DA is able to catalyze benzylic hydroxylation of a variety of compounds, affording the corresponding chiral benzylic alcohols in 86-99 % ee and 130-1020 total turnover numbers.

Preparation of Key Intermediates for the Syntheses of Coenzyme Q10 and Derivatives by Cross-Metathesis Reactions.

An alternative catalytic strategy for the preparation of benzylmethacrylate esters, key intermediates in the synthesis of coenzyme Q10 and derivatives, was reported. This strategy avoided undesirable stoichiometric reduction/oxidation processes by utilizing the catalytic formation of allylarenes and then cross-metathesis to selectively form E-benzylmethacrylate esters with good yields (58-64%) and complete E-selectivity. The ester intermediates were reduced to common key benzylallylic alcohols (90-92% yield), which were subsequently used in the formal syntheses of coenzyme Q10 and one derivative.

Cobalt tungsten oxide hydroxide hydrate (CTOHH) on DNA scaffold: an excellent bi-functional catalyst for oxygen evolution reaction (OER) and aromatic alcohol oxidation.

A material with interdisciplinary properties is of wide interest for use in environmental applications. Currently, hydrogen generation by electrolysis and formation of carbonyl derivatives from alcohols are two different fields that focus on energy and environmental applications. In this work, a new material, Cobalt Tungsten Oxide Hydroxide Hydrate (CTOHH) on deoxyribonucleic acid (DNA) scaffold having chain-like morphology has been prepared for the first time by a facile microwave heating method. The same CTOHH was also prepared without the DNA scaffold and resulted in irregular aggregated molecular structures. Further, both CTOHH-DNA and CTOHH were converted into CoWO4-DNA and CoWO4, respectively by annealing them at a temperature of 600 °C. All the four catalysts were used for electrocatalytic oxygen evolution reaction (OER) and for oxidation of aromatic alcohols. In OER, CTOHH-DNA delivered fruitful results compared to all other electrocatalysts. For attaining a current density of 10 mA cm-2, it just required an overpotential of 355 mV with a Tafel slope value of 47.5 mV dec-1. Similarly, all four catalysts were also analyzed for selective and controlled oxidation of aromatic alcohols to their respective aldehydes and ketones using molecular oxygen as a green oxidant where CTOHH-DNA showed better results. Chemo-selectivity has been observed for CTOHH-DNA in the co-presence of hydroxyl and cyano functional groups. The durability of CTOHH-DNA was analyzed and it showed excellent catalytic activity retention up to five cycles.

Effect of Ultrasound on the Green Selective Oxidation of Benzyl Alcohol to Benzaldehyde.

Oxidation of alcohols plays an important role in industrial chemistry. Novel green techniques, such as sonochemistry, could be economically interesting by improving industrial synthesis yield. In this paper, we studied the selective oxidation of benzyl alcohol as a model of aromatic alcohol compound under various experimental parameters such as substrate concentration, oxidant nature and concentration, catalyst nature and concentration, temperature, pH, reaction duration, and ultrasound frequency. The influence of each parameter was studied with and without ultrasound to identify the individual sonochemical effect on the transformation. Our main finding was an increase in the yield and selectivity for benzaldehyde under ultrasonic conditions. Hydrogen peroxide and iron sulfate were used as green oxidant and catalyst. Coupled with ultrasound, these conditions increased the benzaldehyde yield by +45% compared to silent conditions. Investigation concerning the transformation mechanism revealed the involvement of radical species.

Para-Selective, Iridium-Catalyzed C-H Borylations of Sulfated Phenols, Benzyl Alcohols, and Anilines Directed by Ion-Pair Electrostatic Interactions.

Para C-H borylations (CHB) of tetraalkylammonium sulfates and sulfamates have been achieved using bipyridine-ligated Ir boryl catalysts. Selectivities can be modulated by both the length of the alkyl groups in the tetraalkylammonium cations and the substituents on the bipyridine ligands. Ion pairing, where the alkyl groups of the cation shield the meta C-H bonds in the counteranions, is proposed to account for para selectivity. The 4,4'-dimethoxy-2,2'-bipyridine ligand gave superior selectivities.

Improving biosynthesis of AuPd core-shell nanoparticles through Escherichia coli with the assistance of phytochelatin for catalytic enhanced chemiluminescence and benzyl alcohol oxidation.

In this work, AuPd core-shell nanoparticles (NPs) biosynthesized through Arabidopsis thaliana phytochelatin synthase-modified Escherichia coli (Au-Pd/AtPCS1-E. coli) with catalytic enhanced chemiluminescence (CL) and benzyl alcohol oxidation (BAO) was investigated. Such biosynthesis of AuPd core-shell NPs was obviously enhanced due to insertion of the gene sequence of Arabidopsis thaliana phytochelatin synthase (AtPCS1) to a plasmid vector (pET-28b) of Escherichia coli (E. coli). The obtained Arabidopsis thaliana phytochelatin synthase-modified Escherichia coli (AtPCS1-E. coli) could generate phytochelatins (PCs, (γ-Glu-Cys)n-Gly, n > 1) for efficient capture and enrichment of Au3+. The component and morphology of AuPd core-shell NPs were checked through X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscopy (TEM) and energy dispersive spectrometer (EDS). Catalytic CL (in H2O2-luminol system) and BAO (in H2O2-benzyl alcohol system) effect with different experimental conditions were examined, respectively. These results revealed that multifunctional PCs could effectively facilitate biosynthetic process of AuPd core-shell NPs with better distribution, higher yield and lower cost while stronger CL intensity and higher conversion could be obtained for further quantitative analysis and application.

Cu(I)-doped Fe3O4 nanoparticles/porous C composite for enhanced H2O2 oxidation of carbamazepine.

Cu(I) doped nano-Fe3O4 were synthesized and loaded on ordered porous carbon materials using a facile co-precipitated. The synthesized catalysts were characterized by XRD, XPS, HRTEM, FESEM-EDX mapping and N2 adsorption-desorption. The results showed that the crystal unit cell of Fe3O4 was enlarged due to the implantation of small amount of Cu(I) into the Fe3O4 structure (Fe2.85Cu0.15O4). With increased Cu content, the catalyst was dominated with Cu2O and the Fe3O4 phase disappeared, the catalytic performance of Fe-Cu bimetal oxide became worse. The Cu(I)-Fe3O4/C composite was enriched with Fe(II), Fe(III) and Cu(I) sites. The prepared Cu-Fe bimetal oxide/C composite exhibited higher specific TOF and oxidation efficiency E on carbamazepine oxidation than Fe2.85Cu0.15O4 and Fe3O4. The enhanced catalytic reactivity was attributed to the synergetic effect of surface Fe and Cu species on the H2O2 activation. The dissolved metals induced catalytic reaction at pH 4.5-8.1 was ignorable. Thus, the catalytic decomposition of H2O2 by Cu-Fe3O4/C at near neutral pH was controlled by interface reactions. The CBZ in the close proximity to the interface was attacked by the generated ROS and formed urea, 2-hydroxybenzyl alcohol and other oxidative products.

Inline Reaction Monitoring of Amine-Catalyzed Acetylation of Benzyl Alcohol Using a Microfluidic Stripline Nuclear Magnetic Resonance Setup.

We present an in-depth study of the acetylation of benzyl alcohol in the presence of N, N-diisopropylethylamine (DIPEA) by nuclear magnetic resonance (NMR) monitoring of the reaction from 1.5 s to several minutes. We have adapted the NMR setup to be compatible to microreactor technology, scaling down the typical sample volume of commercial NMR probes (500 µL) to a microfluidic stripline setup with 150 nL detection volume. Inline spectra are obtained to monitor the kinetics and unravel the reaction mechanism of this industrially relevant reaction. The experiments are combined with conventional 2D NMR measurements to identify the reaction products. In addition, we replace DIPEA with triethylamine and pyridine to validate the reaction mechanism for different amine catalysts. In all three acetylation reactions, we find that the acetyl ammonium ion is a key intermediate. The formation of ketene is observed during the first minutes of the reaction when tertiary amines were present. The pyridine-catalyzed reaction proceeds via a different mechanism.