Chitosan microparticles embedded with multi-responsive poly(N-vinylcaprolactam-co-itaconic acid-co-ethylene-glycol dimethacrylate)-based hydrogel nanoparticles as a new carrier for delivery of hydrophobic drugs.

In this paper, chitosan was used as protective agent for dual temperature-/pH-sensitive poly(N-vinylcaprolactam-co-itaconic acid-co-ethylene- glycol dimethacrylate)- based hydrogel nanoparticles (poly(NVCL-co-IA-co-EGDMA)) aiming avoid their undesirable colloidal destabilization at different conditions of body human tissues. Thus, poly(NVCL-co-IA-co-EGDMA) was embedded into chitosan and a new solid dispersion was prepared via spray-drying and ketoprofen was used as carrier. Two different sizes of hydrogel nanoparticles (120.6 nm and 185.9 nm) were evaluated and they exhibited a drug encapsulation efficiency of the 39.6% and 57.8%, respectively. The smaller nanoparticles showed to be faster for releasing of ketoprofen at pH 7.4 and 37 °C due to their larger surface area and higher swelling ability. Chitosan played a role of a secondary barrier for the ketoprofen diffusion, extending its release compared to hydrogel nanoparticles alone. Among two concentrations (40 wt% and 70 wt%) of hydrogel nanoparticles related to chitosan, the first one induced higher percentages of ketoprofen release: 74.2% against 64.6%. In addition, the interactions between chitosan matrix and poly(NVCL-co-IA-co-EGDMA) did not change the multi-responsive behavior of hydrogels, suggesting the chitosan was efficient for keeping integrity of nanoparticles hydrogels. Chitosan/poly(NVCL-co-IA-co-EGDMA) hybrid microparticles seems to be a promising new carrier for release of hydrophobic drugs, such as ketoprofen.

Effect of Delivery Platforms Structure on the Epidermal Antigen Transport for Topical Vaccination.

Transdermal immunization is highly attractive because of the skin's accessibility and unique immunological characteristics. However, it remains a relatively unexplored route of administration because of the great difficulty of transporting antigens past the outermost layer of skin, the stratum corneum. In this article, the abilities of three poly( N-vinylcaprolactam) (PVCL)-based thermoresponsive assemblies-PVCL hydrogels and nanogels plus novel film forming PVCL/acrylic nanogels-to act as protein delivery systems were investigated. Similar thermal responses were observed in all systems, with transition temperatures close to 32 °C, close to that of the skin surface. The investigated dermal delivery systems showed no evidence of cytotoxicity in human fibroblasts and were able to load and release ovalbumin (OVA), a well-studied antigen, in a temperature-dependent manner in vitro. The penetration of OVA into ex vivo human skin following topical application was evaluated, where enhanced skin delivery was seen for the OVA-loaded PVCL systems relative to administration of the protein alone. The distinct protein release and skin penetration profiles observed for the different PVCL assemblies were here discussed on the basis of their structural differences.

Synthesis and characterization of poly(N-vinylcaprolactam)-based spray-dried microparticles exhibiting temperature and pH-sensitive properties for controlled release of ketoprofen.

Poly(N-vinylcaprolactam) (PNVCL) and poly(N-vinylcaprolactam-co-acrylic acid) (poly(NVCL-co-AA)) were synthesized by solution-free radical polymerization and displayed thermo-responsive behavior, with lower critical solution temperatures (LCSTs) of 35 °C and 39 °C, respectively. The incorporation of AA unities made the poly(NVCL-co-AA) sensitive to both pH and temperature. They were exploited in this work in preparing microparticles loaded with ketoprofen via spray-drying to modulate the drug release rate by changing pH or temperature. The interaction between polymer and drug was studied using X-ray diffractometry, Raman spectrometry and scanning electron microscopy (SEM). The biocompatibility of pure polymers, free ketoprofen as well as the spray-dried particles was demonstrated in vitro by low cytotoxicity and a lack of nitric oxide production in macrophages at concentrations as high as 100 µg/ml. The release profile of ketoprofen was evaluated by in vitro assays at different temperatures and pH values. Drug diffusion out of PNVCL's hydrated polymer network is increased at temperatures below the LCST. However, when poly(NVCL-co-AA) was used as the matrix, the release of ketoprofen was primarily controlled by the pH of the medium. These results indicated that PNVCL and the novel poly(NVCL-co-AA) could be promising candidates for pH and temperature-responsive drug delivery systems.

* Thermosensitive Poly(N-vinylcaprolactam) Injectable Hydrogels for Cartilage Tissue Engineering.

Injectable hydrogels have gained prominence in the field of tissue engineering for minimally invasive delivery of cells for tissue repair and in the filling of irregular defects. However, many injectable hydrogels exhibit long gelation times or are not stable for long periods after injection. To address these concerns, we used thermosensitive poly(N-vinylcaprolactam) (PNVCL) hydrogels due to their cytocompatibility and fast response to temperature stimuli. Changes in the PNVCL molecular weight and concentration enabled the development of hydrogels with tunable mechanical properties and fast gelation times (<60 s when the temperature was raised from room temperature to physiologic temperature). Chondrocytes (CHs) and mesenchymal stem cells were encapsulated in PNVCL hydrogels and exhibited high viability (∼90%), as monitored by Live/Dead staining and Alamar Blue assays. Three-dimensional constructs of CH-laden PNVCL hydrogels supported cartilage-specific extracellular matrix production both in vitro and after subcutaneous injection in nude rats for up to 8 weeks. Moreover, biochemical analyses of constructs demonstrated a time-dependent increase in glycosaminoglycans (GAGs) and collagen, which were significantly augmented in the implants cultured in vivo. Histological analyses also demonstrated regular distribution of synthesized cartilage components, including abundant GAGs and type II collagen. The findings from this study demonstrate thermosensitive PNVCL as a candidate injectable biomaterial to deliver cells for cartilage tissue engineering.

Unusual alkaloids of the highland species Astragalus cryptanthus Wedd. (Fabaceae).

Two unusual caprolactam alkaloids, 3-(dimethylamino)hexahydro-2H-azepin-2-one and 3-(methylamino)-hexahydro-2H-azepin-2-one, were isolated from the aerial parts of Astragalus cryptanthus Wedd.; their structures were unambiguously determined based on data from extensive 1D and 2D NMR, GC-MS and FT-IR spectroscopic analyses. This is the first report of this alkaloid type in the genus Astragalus.

Synthesis and characterization of stimuli-responsive polypropylene containing N-vinylcaprolactam and N-vinylimidazole obtained by ionizing radiation.

Polypropylene films were grafted with thermo-responsive N-vinylcaprolactam and pH-responsive N-vinylimidazole polymers by means of gamma radiation using pre-irradiation and direct methods, in order to functionalize the films with thermo- and/or pH-responsiveness. The dependence of grafting yield on parameters such as co-monomer concentration, pre-irradiation dose, temperature, and reaction time was evaluated. The samples were characterized by Fourier transform infrared and X-ray photoelectron spectroscopies, differential scanning calorimetry, thermogravimetric analysis, swelling studies in different solvents, and water contact angle. The grafted copolymers presented thermo- and pH-sensitiveness, highlighting their potential as advanced biomaterials, capable of providing adequate environment for hosting and sustained release of antimicrobial drugs bearing cationic moieties, such as groups of diclofenac, while still exhibiting good cytocompatibility.

Effect of the molecular architecture on the thermosensitive properties of chitosan-g-poly(N-vinylcaprolactam).

A series of thermoresponsive copolymers based on chitosan-g-poly(N-vinylcaprolactam) were synthesized by amidation reaction using 4-(4,6-dimethoxy-1,3,5-triazin-2-yl)-4-methylmorpholinium chloride as coupling reagent. The effect of molecular architecture on the thermoresponsive properties of the graft copolymers solutions was studied by varying the chain length of the grafted poly(N-vinylcaprolactam), PVCL, (in the range from 4 to 26 kDa) and the spacing between grafted chains onto the chitosan backbone. The most interesting characteristic of these copolymers is their solubility in water at temperatures below their lower critical solution temperature (LCST). These solutions presented a LCST between 36 and 44 °C, which decreases with the spacing and length of grafted PVCL chains onto the chitosan backbone, in contrast with the limited decrease of the LCST of PVCL above a critical M¯n value around 18 kDa. This behavior offers tangible possibilities for the preparation and application of sensitive bioactive formulations and "smart" drug delivery systems.

Electrospun polyamide 6/poly(allylamine hydrochloride) nanofibers functionalized with carbon nanotubes for electrochemical detection of dopamine.

The use of nanomaterials as an electroactive medium has improved the performance of bio/chemical sensors, particularly when synergy is reached upon combining distinct materials. In this paper, we report on a novel architecture comprising electrospun polyamide 6/poly(allylamine hydrochloride) (PA6/PAH) nanofibers functionalized with multiwalled carbon nanotubes, used to detect the neurotransmitter dopamine (DA). Miscibility of PA6 and PAH was sufficient to form a single phase material, as indicated by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC), leading to nanofibers with no beads onto which the nanotubes could adsorb strongly. Differential pulse voltammetry was employed with indium tin oxide (ITO) electrodes coated with the functionalized nanofibers for the selective electrochemical detection of dopamine (DA), with no interference from uric acid (UA) and ascorbic acid (AA) that are normally present in biological fluids. The response was linear for a DA concentration range from 1 to 70 µmol L(-1), with detection limit of 0.15 µmol L(-1) (S/N = 3). The concepts behind the novel architecture to modify electrodes can be potentially harnessed in other electrochemical sensors and biosensors.

Effect of gamma irradiation on caprolactam migration from multilayer polyamide 6 films into food simulants: development and validation of a gas chromatographic method.

A GC method to determine caprolactam in water, 15% ethanol, and olive oil food simulants was developed and validated. Linear ranges varied from 0.96 to 642.82 microg/mL for water, 0.64 to 800.32 microg/mL for 15% ethanol, and 1.06 to 1062.34 microg/g for olive oil, with correlation coefficients higher than 0.999. Method precision studies showed RSD values lower than 5.45%, while method accuracy studies showed recovery from 72 to 111% for all simulants. The effect of gamma irradiation on caprolactam migration from multilayer polyamide 6 (PA-6) films intended for cheese into water, 15% ethanol, olive oil, and 3% acetic acid simulants was also studied. For migration assay, non-irradiated and irradiated (12 kGy) films were placed in contact with the simulant and exposed at 40 degrees C for 10 days. The validated method was used to quantify caprolactam migration from multilayer PA-6 films into the simulants, which ranged from 1.03 to 7.59 mg/kg for non-irradiated films, and from 4.82 to 11.32 mg/kg for irradiated films. Irradiation caused almost no changes in caprolactam levels, with the exception of olive oil, which showed an increase in the caprolactam level. All multilayer PA-6 films were in accordance with the requirements of the legislation for caprolactam migration.

Expression, purification and immobilization of the intracellular invertase INVA, from Zymomonas mobilis on crystalline cellulose and Nylon-6.

This paper presents two immobilization methods for the intracellular invertase (INVA), from Zymomonas mobilis. In the first method, a chimeric protein containing the invertase INVA, fused through its C-terminus to CBDCex from Cellulomonas fimi was expressed in Escherichia coli strain BL21 (DE3). INVA was purified and immobilized on crystalline cellulose (Avicel) by means of affinity, in a single step. No changes were detected in optimal pH and temperature when INVA-CBD was immobilized on Avicel, where values of 5.5 and 30 degrees C, respectively, were registered. The kinetic parameters of the INVA-CBD fusion protein were determined in both its free form and when immobilized on Avicel. Km and Vmax were affected with immobilization, since both showed an increase of up to threefold. Additionally, we found that subsequent to immobilization, the INVA-CBD fusion protein was 39% more susceptible to substrate inhibition than INVA-CBD in its free form. The second method of immobilization was achieved by the expression of a 6xHis-tagged invertase purified on Ni-NTA resin, which was then immobilized on Nylon-6 by covalent binding. An optimal pH of 5.5 and a temperature of 30 degrees C were maintained, subsequent to immobilization on Nylon-6 as well as with immobilization on crystalline cellulose. The kinetic parameters relating to Vmax increased up to 5.7-fold, following immobilization, whereas Km increased up to 1.7-fold. The two methods were compared showing that when invertase was immobilized on Nylon-6, its activity was 1.9 times that when immobilized on cellulose for substrate concentrations ranging from 30 to 390 mM of sucrose.

Immobilization of the recombinant invertase INVB from Zymomonas mobilis on Nylon-6.

The recombinant invertase INVB (re-INVB) from Zymomonas mobilis was immobilized on microbeads of Nylon-6, by means of covalent bonding. The enzyme was strongly and successfully bound to the support. The activity of the free and immobilized enzyme was determined, using 10% (w/v) sucrose, at a temperature ranging between 15 and 60 degrees C and a pH ranging between 3.5 and 7. The optimal pH and temperature for the immobilized enzyme were 5.5 and 25 degrees C, respectively. Immobilization of re-INVB on Nylon-6 showed no significant change in the optimal pH, but a difference in the optimal temperature was evident, as that for the free enzyme was shown to be 40 degrees C. The values for kinetic parameters were determined as: 984 and 98 mM for Kappm of immobilized and free re-INVB, respectively. Kappcat values for immobilized and free enzymes were 6.1x10(2) and 1.2x10(4) s(-1), respectively, and immobilized re-INVB showed Vappmax of 158.73 micromol h min(-1) mg(-1). Immobilization of re-INVB on Nylon-6 enhanced the thermostability of the enzyme by 50% at 30 degrees C and 70% at 40 degrees C, when compared to the free enzyme. The immobilization system reported here may have future biotechnological applications, owing to the simplicity of the immobilization technique, the strong binding of re-INVB to the support and the effective thermostability of the enzyme.

Identification and migration of degradation compounds from irradiation of multilayer polyamide 6 films for meat foodstuffs and cheese.

The aim of this work was to identify the degradation compounds produced during irradiation of multilayer polyamide 6 (PA-6) films and to study their migration into water and 95% ethanol food simulant. After irradiation of multilayer PA-6 films at 3, 7 and 12 kGy, degradation compounds were extracted using solid-phase microextraction, for which the time and temperature of extraction and stirring were optimized, and identified by gas chromatography-mass spectrometry. Caprolactam, 2-cyclopentylcyclopentanone and aldehydes, among other compounds, were identified in the headspace of the films. Polydimethylsiloxane was considered the best fiber for extraction. The optimum conditions of time, temperature and stirring to extract the compounds were 20 min, 80 degrees C and 225 rpm. For validation purposes, the compounds were quantified in water and 95% ethanol and the results showed high sensitivity, good precision and accuracy. Migration of compounds from irradiated and non-irradiated multilayer PA-6 films into water and 95% ethanol food simulants was carried out at 40 degrees C for 10 days. The method was efficient for the quantification of decaldehyde, 2-cyclopentylcyclopentanone and caprolactam that migrated from multilayer PA-6 films into food simulants.

Nylon-6 cylinders and a sponge-like derivative as supports for immobilizing trypsin.

1. Two types of nylon-6 supports (small cylinders and a sponge-like derivative) were prepared for immobilizing enzymes. Nylon-6 beads were solubilized by immersion in 80% formic acid and then reprecipitated using two different types of non-solvent solutions (distilled water or a 1:1 acetone:water solution) giving rise to a sponge-like derivative and to a colloidal suspension, respectively. The latter was molded into a thin thread which was cut into small cylinders. 2. Trypsin (EC 3.4.21.4) was covalently bound to glutaraldehyde-activated nylon-6 cylinders as well as to the sponge-like derivative. The maximum (100%) apparent initial enzymatic activity was found for the trypsin bound to small cylinders, while the initial activity of trypsin bound to the sponge-like material was 61% in comparison with that of trypsin-small cylinders, under the same conditions of enzyme immobilization reaction (1 g of nylon support and 5 ml of 1.3 mg/ml trypsin in 0.1 M sodium phosphate buffer, pH 8.5, at 10 degrees C for 18 h) and of enzymatic reaction (1 g of trypsin-nylon in a batch reactor, 2 ml of 0.7% w/v azocasein solution in 50 mM borate buffer, pH 8.5, at 37 degrees C, with shaking, for 1 h). However, the decrease of activity after enzyme immobilization was more conspicuous for the trypsin-small cylinders than for the trypsin-sponge. The former retained approximately 25% of its initial activity, while the latter retained approximately 67% of its initial activity, after seven cycles of utilization for 1 h, pH 8.5, at 37 degrees C and 8 days of storage, pH 8.5, at 4 degrees C in the presence of azocasein. 3. Scanning electron microscopy was performed to visualize the surface of the support after each step of the immobilization process. The electron micrographs show that the two types of nylon supports had a rough surface, which became rougher and full of craters after treatment with 5 N HCl. On the other hand, the partially hydrolyzed nylon surface acquired the appearance of Swiss cheese after treatment with 2.5% glutaraldehyde. After reaction with the enzyme molecules the surface became rougher again.