The feasibility and applicability of sequential extraction of high value-added biogenic materials from sewage sludge.

The sequential extraction routes of biogenic materials from sewage sludge (SS) were investigated. Physical methods (ultrasound, heating) and chemical methods (sodium hydroxide, sodium carbonate) were used to extract extracellular polymeric substances (EPS) and alginate-like extracellular polymers (ALEs) from SS. The residues after extraction were further subjected to physical methods (heating) and chemical methods (sulfuric acid, sodium hydroxide) for protein extraction. A comparison was made between sequential extraction routes and direct extraction of biomaterials from sludge in terms of extraction quantity, material properties, and applicability. The results showed that sequential extraction of biomaterials is feasible. The highest extraction quantities were obtained when using sodium carbonate for EPS and ALE extraction and sodium hydroxide for protein, reaching 449.80 mg/gVSS, 109.78 mg/gVSS, and 5447.08 mg/L, respectively. Sequential extraction procedures facilitate the extraction of biomaterials. Finally, suitable extraction methods for different application scenarios were analyzed.

Fractionation of Carlina acaulis L. Root Methanolic Extract as a Promising Path towards New Formulations against Bacillus cereus and Methicillin-Resistant Staphylococcus aureus.

The root of Carlina acaulis L. has been widely used in traditional medicine for its antimicrobial properties. In this study, the fractionation of methanol extract from the root was conducted. Four fractions (A, B, C, and D) were obtained and tested against a range of bacteria and fungi. The results showed promising antibacterial activity, especially against Bacillus cereus, where the minimal inhibitory concentration (MIC) was determined to be equal to 0.08 mg/mL and 0.16 mg/mL for heptane (fraction B) and ethyl acetate (fraction C), respectively. In the case of the methicillin-resistant Staphylococcus aureus (MRSA) ATCC 43300 strain, the same fractions yielded higher MIC values (2.5 and 5.0 mg/mL, respectively). This was accompanied by a lack of apparent cytotoxicity to normal human BJ foreskin fibroblasts, enterocytes derived from CaCo2 cells, and zebrafish embryos. Further analyses revealed the presence of bioactive chlorogenic acids in the fractionated extract, especially in the ethyl acetate fraction (C). These findings support the traditional use of the root from C. acaulis and pave the way for the development of new formulations for treating bacterial infections. This was further evaluated in a proof-of-concept experiment where fraction C was used in the ointment formulation, which maintained high antimicrobial activity against MRSA and displayed low toxicity towards cultured fibroblasts.

Impact of extraction method on the lipids of Himalayan marmot oil with ultrahigh-performance liquid chromatography Q-Exactive Orbitrap mass spectrometry analysis.

RATIONALE: Himalayan marmot oil (SPO) has been used for pharmaceutical purposes for centuries, but its composition is still unclear. The bioactivity of SPO highly depends on the techniques used for its processing. This study focused on the comprehensive lipidomics of SPO, especially on the ones derived from dry rendering, wet rendering, cold pressing, and ultrasound-assisted solvent extraction. METHODS: We performed lipid profiling of SPO acquired by different extraction methods using ultrahigh-performance liquid chromatography Q-Exactive Orbitrap mass spectrometry, and 17 classes of lipids (2 BMPs, 12 LysoPCs, 9 LysoPEs, 41 PCs, 24 PEs, 23 Plasmenyl-PCs, 10 Plasmenyl-PEs, 10 MGs, 63 DGs, 187 TGs, 2 MGDGs, 3 Cer[NDS]s, 22 Cer[NS]s, 2 GlcCer[NS]s, 14 SMs, 14 CEs, and 6 AcylCarnitines) were characterized. RESULTS: Fifty-five lipids were differentially altered (VIP > 1.5, p < 0.05) between the extraction techniques, which can be used as potential biomarkers to differentiate SPO extracted by various methods. Additionally, the contents of oleic acid and arachidic acid were abundant in all samples that may suggest their medicinal values and are conducive to in-depth research. CONCLUSIONS: These findings reveal the alterations of lipid profile and free fatty acid composition in SPO obtained with different extraction methods, providing a theoretical foundation for investigating its important components as functional factors in medicines and cosmetics.

A comprehensive review on pulse protein fractionation and extraction: processes, functionality, and food applications.

The increasing world population requires the production of nutrient-rich foods. Protein is an essential macronutrient for healthy individuals. Interest in using plant proteins in foods has increased in recent years due to their sustainability and nutritional benefits. Dry and wet protein fractionation methods have been developed to increase protein yield, purity, and functional and nutritional qualities. This review explores the recent developments in pretreatments and fractionation processes used for producing pulse protein concentrates and isolates. Functionality differences between pulse proteins obtained from different fractionation methods and the use of fractionated pulse proteins in different food applications are also critically reviewed. Pretreatment methods improve the de-hulling efficiency of seeds prior to fractionation. Research on wet fractionation methods focuses on improving sustainability and functionality of proteins while studies on dry methods focus on increasing protein yield and purity. Hybrid methods produced fractionated proteins with higher yield and purity while also improving protein functionality and process sustainability. Dry and hybrid fractionated proteins have comparable or superior functionalities relative to wet fractionated proteins. Pulse protein ingredients are successfully incorporated into various food formulations with notable changes in their sensory properties. Future studies could focus on optimizing the fractionation process, improving protein concentrate palatability, and optimizing formulations using pulse proteins.

Changes in the extractability and fractionation of cadmium and copper in a contaminated soil amended with various sugarcane bagasse-based materials.

Heavy-metal contamination in soil has long been a persistent challenge and the utilization of agricultural waste for in-situ stabilization remediation presents a promising approach to tackle this problem. Agricultural wastes exhibit promising potential in the remediation of contaminated land and modification could improve the adsorption performance markedly. Citric acid and Fe3O4 treated sugarcane bagasse adsorbed more heavy metals than raw materials in the aqueous system, employing these materials for heavy metal remediation in soil holds significant implications for broadening the raw material source of passivators and enhancing waste utilization efficiency. In this paper, a 120-day soil incubation study was conducted to compare the effects of pristine sugarcane bagasse (SB), citric-acid modified (SSB1, SSB2 and SSB3 with increasing proportion of citric acid) and citric-acid/Fe3O4 modified (MSB1, MSB4 and MSB7 with increasing proportion of Fe3O4) sugarcane bagasse at 1 % addition rate on cadmium (Cd) and copper (Cu) passivation. The SB, SSB1 and MSB1 did not always decrease the content of CaCl2-extractable Cd while all the seven amendments decreased the CaCl2-extractable Cu during the experiment period. Among all materials, SSB3 and MSB7 exhibited the highest efficiency in reducing the concentrations of CaCl2-extractable Cd and Cu. At Day 120, SB, SSB3 and MSB7 reduced the content of CaCl2-extractable Cd by 8 %, 18 % and 24 %, and of CaCl2-extractable Cu by 25 %, 50 % and 61 %, respectively. The efficiency of Cd and Cu immobilization was associated positively with the pH, functional groups and H-bonds of the amendments. The results suggest that the efficiency of sugarcane bagasse in heavy-metal passivation can be largely enhanced through chemical modifications using high proportions of citric acid and Fe3O4.

High potential extracts from cocoa byproducts through sonotrode optimal extraction and a comprehensive characterization.

Cocoa pod husk (CPH) and cocoa bean shell (CBS) are by-products obtained during pre-processing and processing of cocoa beans. Several bioactive compounds have been identified in these by-products that can be used for commercial applications as a way to promote the circular economy. Therefore, the objective of this paper was to recover bioactive compounds from CPH and CBS by sonoextraction process, to determine the type, content, and antioxidant activity in optimized extracts. To achieve our purpose, an optimization strategy using Box-Behnken Design coupled response surface methodology (MRS) was applied. The extraction conditions were optimized. The results obtained for CBS were: TPC (193 mg GAE/g), TEAC (1.02 mmol TE/g), FRAP (1.02 mmol FeSO4/g) and ORAC (2.6 mmol TE/g), while for CPH, the reported values were: TPC (48 mg GAE/g), TEAC (0.30 mmol TE/g), FRAP (0.35 mmol FeSO4/g) and ORAC (0.43 mmol TE/g) under the optimized conditions: Time (XA): 15 min, Amplitude (XB): 80 %, Ethanol (XC): 50 %. The LC-ESI-qTOF-MS analysis results allowed the identification of 79 compounds, of which 39 represent the CBS extract, while 40 compounds were identified in CPH extract. To conclude, sonotrode based extraction could be considered as an efficient and fast alternative for the recovery of bioactive substances from CBS and CPH.

Green and efficient extraction of phenolic compounds from Neem leaves using deep eutectic solvents based ultrasonic-assisted extraction.

Deep eutectic solvent (DES) combined with ultrasonic-assisted extraction was employed as an environmentally friendly technique for extracting antioxidant phenolic compounds from Neem leaves in place of organic solvents. Choline chloride-Ethylene glycol (1:2) with 40% V/V water content (DES-1) was investigated as a potential total phenolic content extractant (38.2 ± 1.2 mg GAE/g DW, where GAE: gallic acid equivalent, DW: dry weight). The optimal operational parameters assessed using single-factor experiments to maximize the total phenolic compounds content were as follows: extraction time of 30 min, 40% V/V water content, liquid-solid ratio of 15:1, and room temperature. Additionally, the in-vitro antioxidant experiments (2,2-diphenyl-1- picrylhydrazyl radical scavenging assay and ferric reducing antioxidant power assay) demonstrated the DES-1-based extract of Neem leaves as a potent antioxidant agent, compared to traditional solvents. Moreover, microscopic morphological analysis supported the effectiveness of DES-1 for the noticeable alteration in the fiber surface structure of Neem leaves after extraction which benefited in the release of polyphenols from these leaves. Eventually, the mass analysis of the extract disclosed the presence of eleven polyphenols in the extract. The Green Analytical Procedure Index revealed the greenness of the extraction method.

Ultrasonication followed by aqueous two-phase system for extraction, on-site modification and isolation of microalgal starch with reduced digestibility.

Microalgae are new and sustainable sources of starch with higher productivity and flexible production modes than conventional terrestrial crops, but the downstream processes need further development. Here, ultrasonication (with power of 200 W or 300 W and duration of 10, 15, 20, or 25 min) was applied to simultaneously extract and modify starch from a marine microalga Tetraselmis subcordiformis for reducing the digestibility, and an aqueous two-phase system (ATPS) of ethanol/NaH2PO4 was then used to isolate the starches with varied properties. Increasing ultrasonic duration facilitated the partition of starch into the bottom pellet, while enhancing the ultrasonic power was conducive to the allocation in the interphase of the ATPS. The overall starch recovery yield reached 73 âˆ¼ 87 % and showed no significant difference among the ultrasonic conditions tested. The sequential ultrasonication-ATPS process successfully enriched the starch with purities up to 65 % âˆ¼ 88 %, which was among the top levels reported in microalgal starch isolated. Ultrasonication produced more amylose which was mainly fractionated into the interface of the ATPS. The digestibility of the starch was altered under different ultrasonic conditions and varied from different ATPS phases as well, with the one under the ultrasonic power of 200 W for 15 min at the bottom pellet having the highest resistant starch content (RS, 39.7 %). The structural and compositional analysis evidenced that the ultrasonication-ATPS process could exert impacts on the digestibility through altering the surface roughness and fissures of the starch granules, modulating the impurity compositions (protein and lipid) that could interact with starch, and modifying the long- and short-range ordered structures. The developed ultrasonication-ATPS process provided novel insights into the mechanism and strategy for efficient production of functional starch from microalgae with a potential in industrial application.

Deep eutectic solvents as sustainable extraction media for extraction of polysaccharides from natural sources: Status, challenges and prospects.

Deep eutectic solvents (DES) emerge as promising alternatives to conventional solvents, offering outstanding extraction capabilities, low toxicity, eco-friendliness, straightforward synthesis procedures, broad applicability, and impressive recyclability. DES are synthesized by combining two or more components through various synthesis procedures, such as heat-assisted mixing/stirring, grinding, freeze drying, and evaporation. Polysaccharides, as abundant natural materials, are highly valued for their biocompatibility, biodegradability, and sustainability. These versatile biopolymers can be derived from various natural sources such as plants, algae, animals, or microorganisms using diverse extraction techniques. This review explores the synthesis procedures of DES, their physicochemical properties, characterization analysis, and their application in polysaccharide extraction. The extraction optimization strategies, parameters affecting DES-based polysaccharide extraction, and separation mechanisms are comprehensively discussed. Additionally, this review provides insights into recently developed molecular guides for DES screening and the utilization of artificial neural networks for optimizing DES-based extraction processes. DES serve as excellent extraction media for polysaccharides from different sources, preserving their functional features. They are utilized both as extraction solvents and as supporting media to enhance the extraction abilities of other solvents. Continued research aims to improve DES-based extraction methods and achieve selective, energy-efficient processes to meet the demands of this expanding field.

A solvent-free squeezing method for extraction of collected mass from aerosols of electronic cigarettes and heated tobacco products.

Previous in vitro toxicological assessments have demonstrated that almost no mutagenic and genotoxic activities in electronic cigarette (e-cigarette) and heated tobacco product (HTP) aerosols were detected even at the maximum recommended concentration. To accurately compare the toxicity levels between cigarette smoke and e-cigarette or HTP aerosols, higher exposure concentrations increasing the possibility to detect toxicity in in vitro tests are necessary, while avoiding solvent-induced toxicity. This study aimed to develop a solvent-free extraction method to obtain concentrated aerosol extracts for improved toxicological evaluation. Our novel approach involved squeezing several Cambridge filter pads, which collected aerosol constituents, in closed containers to achieve solvent-free extraction with comparable efficiency to the conventional method using organic solvents. The optimized squeezing method yielded extracts with concentrations approximately 10 times higher than those obtained in conventional extraction methods. Yield comparison of various constituents, such as flavoring compounds, in e-cigarette aerosol extracts revealed similar extraction efficiencies between the squeezing and conventional methods. However, the extraction efficiency for constituents with high log Pow values, predominantly found in HTP aerosol extracts, was unacceptably low using the squeezing method. In addition, solvent-free centrifuging, another type of extraction method, exhibited unsatisfactory results for even e-cigarette aerosols compared with the conventional method. Our findings suggest that the solvent-free squeezing method is suitable for extracting aerosol collected mass from e-cigarette aerosol but not from HTP aerosol. We anticipate that the solvent-free squeezing method will contribute to a deeper understanding of toxicological differences between e-cigarettes and conventional combustible cigarettes.

Green fractionation and hydrolysis of fish meal to improve their techno-functional properties.

A green strategy employing water as solvent has been adopted to obtain protein hydrolysates from fish meal (FM), its water-soluble fraction (WSP), and its non-water-soluble fraction (NSP). The techno-functional properties of the hydrolysates have been investigated and compared to hydrolysates obtained with Alcalase®. In general, SWH hydrolysates presented higher content of free amino acids and higher degree of hydrolysis, which reflected on the molecular size distribution. However, Alcalase® hydrolysates presented better solubility (from 74 ± 4% for NSP at pH = 2 up to 99 ± 1% for WSP at pH = 4-7). According to fluorescence experiments, FM and NSP hydrolysates showed the highest surface hydrophobicity, which has been related to better emulsifying properties and higher emulsion stability. The emulsions stabilized with 2%wt. of SWH-treated NSP showed the smallest particle sizes, with D[4,3] = 155 nm at day 0, and good stability, with D[4,3] = 220 nm at day 7, proving that water fractionation followed by SWH treatment is a good method to improve the techno-functional properties of the hydrolysates.

Synergism of jet milling and deep eutectic solvent pretreatment on grapevine lignin fractionation and enhancing enzymatic hydrolysis.

Herein, we investigated the synergistic effects of jet milling (JM) and deep eutectic solvent (DES) pretreatment on the fractionation of grapevine lignin and the consequent enhancement of enzymatic hydrolysis. Grapevine, a substantial byproduct of the wine industry, was subjected to JM pretreatment to produce finely powdered particles (median diameter D50 = 98.90), which were then further treated with acidic ChCl-LA and alkaline K2CO3-EG DESs. The results revealed that the combined JM + ChCl-LA pretreatment significantly increased the cellulose preservation under optimal conditions (110 °C, 4 h, and 20 % water content), achieving removal rates of 74.18 % xylan and 66.05 % lignin, respectively. The pretreatment temperature and inhibitor production were reduced, resulting in a remarkable threefold increase in glucose yield compared to untreated samples. Moreover, the structural analysis of the pretreated lignin indicated an enrichment of phenolic units, leading to enhanced antioxidant and antibacterial activities, particularly in the JM pretreated samples. These findings underscore the promising potential of the synergistic JM and DES pretreatment in facilitating the efficient utilization of grapevine lignocellulosic biomass for sustainable biorefinery technologies.

Fractionation and characterisation of sialylated-mucin glycoprotein from edible birds' nest hydrolysates through anion exchange chromatography.

Edible bird's nest (EBN) is made up of sialylated-mucin glycoprotein with various health benefits due to its high antioxidative activity. However, as a macromolecule with distinct charged sialic acid and amino acids, fractions with different charges would have varied physicochemical properties and antioxidant activity, which have not been studied. Therefore, this study aimed to fractionate and purify the enzymatic hydrolysed of cleaned EBN (EBNhc) and EBN by-product (EBNhbyp) through anion exchange chromatography (AEC), and determine their molecular weights, physicochemical properties, and antioxidative activities. Overall, 26 fractionates were collected from enzymatic hydrolysate by AEC, which were classified into 5 fractions. It was found that the positively charged fraction of EBNhc (CF 1) and EBNhbyp (DF 1) showed the significantly highest (p < 0.05) soluble protein contents (22.86 and 18.40 mg/g), total peptide contents (511.13 and 800.47 mg/g) and ferric reducing antioxidant power (17.44 and 6.96 mg/g) among the fractionates. In conclusion, a positively charged fraction (CF 1 and DF 1) showed more desired physicochemical properties and antioxidative activities. This research suggests the potential of AEC fractionation as a technology to purify EBN and produce positively charged EBN fractionates with antioxidative potential that could be applied as food components to provide health benefits.

Fractionation of cassava pectins and their detailed structural analyses using various pectinolytic enzymes.

In this study, we analyzed the pectin structure within the pulp of cassava. Cassava pectin, derived from cassava pulp treatment at 120 °C for 90 min, was separated into four fractions (CP-P, CP-SD1, CP-SD2F, and CP-SD2R) based on variations in water solubility, electrical properties, and molecular weights. Sugar composition analysis demonstrated an abundance of homogalacturonan (HG) in CP-P and CP-SD2F, rhamnogalacturonan I (RG-I) in CP-SD2R, and neutral sugars in CP-SD1. Because RG-I possesses a complex structure, we analyzed CP-SD2R using various pectinolytic enzymes. Galactose was the major sugar in CP-SD2R accounting for 49 %, of which 65 % originated from arabinogalactan I, 9 % from galactose and galactooligosaccharides, 5 % from arabinogalactan II, and 11 % from galactoarabinan. Seventy-four percent of arabinose in CP-SD2R was present as galactoarabinan. The methylation (DM) and acetylation (DAc) degrees of cassava pectin were 11 and 15 %, respectively. The HG and RG-I regions exhibited DAc values of 5 and 44 %, respectively, signifying the high DAc of RG-I compared to HG. Information derived from the structural analysis of cassava pectin will enable efficient degradation of pectin and cellulose, leading to the use of cassava pulp as a raw material for biorefineries.

Niobium-based single-atom catalyst promoted fractionation of lignocellulose in choline chloride-lactic acid deep eutectic solvent.

Pretreatment is the key step to convert lignocelluloses to sustainable biofuels, biochemicals or biomaterials. In this study, a green pretreatment method based on choline chloride-lactic acid deep eutectic solvent (ChCl-LA) and niobium-based single-atom catalyst (Nb/CN) was developed for the fractionation of corn straw and further enzymatic hydrolysis of cellulose. With this strategy, significant lignin removal of 96.5 % could be achieved when corn straw was pretreated by ChCl-LA (1:2) DES over Nb/CN under 120 °C for 6 h. Enzymatic hydrolysis of the cellulose-enriched fraction (CEF) presented high glucose yield of 92.7 % and xylose yield of 67.5 %. In-depth investigations verified that the high yields of fractions and monosaccharides was attributed to the preliminary fractionation by DES and the deep fractionation by Nb/CN. Significantly, compared to other reported soluble catalysts, the synthesized single-atom catalyst displayed excellent reusability by simple filtration and enzymatic hydrolysis. The recyclability experiments showed that the combination of ChCl-LA DES and Nb/CN could be repeated at least three times for corn straw fractionation, moreover, the combination displayed remarkable feedstock adaptability.

Ultrasound assisted extraction of phytochemicals from Piper betel L.

Piper betel contains phytochemicals with diverse pharmacological effects. The objective of this study was to enhance the extraction efficiency of phytochemicals and the chlorophyll content using ultrasonication. The Box-Behnken design was employed to optimize the time (10, 20, 30 min), temperature (20, 30, and 40 °C), and solid-solvent ratio (1:10, 1:20, 1:30) by utilizing response surface methods with three independent variables. Multiple parameters, including extract yield, total phenol, total flavonoid, antioxidant activity, and chlorophyll content were used to optimize the conditions. The linear relationship between power intensity and responses was determined to be statistically significant, with a p-value less than 0.01. The interaction effect of temperature, time, and ratio of solid solvent was shown to be statistically significant (p < 0.05) for all the obtained results. The optimal parameters for achieving the highest extract yield were as follows: a temperature of 40 °C, a sonication time of 30 min, and a solid solvent ratio of 1:10. These conditions result in an extract yield of 21.99 %, a total flavonoid content of 44.97 mg/GAE, a total phenolic content of 185.05 mg/GAE, a DPPH scavenging activity of 99.1 %, and a chlorophyll content of 49.95 mg/ml. This study highlights the significance of customized extraction methodologies for optimizing the bioactive capacity of phytochemicals derived from betel leaves. The elucidation of extraction parameters and the resultant phytochemical profiles serves as a fundamental framework for the advancement of innovative pharmaceuticals and nutraceuticals, capitalizing on the therapeutic attributes of this traditional medicinal botanical.

Pentavalent U Reactivity Impacts U Isotopic Fractionation during Reduction by Magnetite.

Meaningful interpretation of U isotope measurements relies on unraveling the impact of reduction mechanisms on the isotopic fractionation. Here, the isotope fractionation of hexavalent U [U(VI)] was investigated during its reductive mineralization by magnetite to intermediate pentavalent U [U(V)] and ultimately tetravalent U [U(IV)]. As the reaction proceeded, the remaining aqueous phase U [containing U(VI) and U(V)] systematically carried light isotopes, whereas in the bicarbonate-extracted solution [containing U(VI) and U(V)], the δ238U values varied, especially when C/C0 approached 0. This variation was interpreted as reflecting the variable relative contribution of unreduced U(VI) (δ238U < 0‰) and bicarbonate-extractable U(V) (δ238U > 0‰). The solid remaining after bicarbonate extraction included unextractable U(V) and U(IV), for which the δ238U values consistently followed the same trend that started at 0.3-0.5‰ and decreased to ∼0‰. The impact of PIPES buffer on isotopic fractionation was attributed to the variable abundance of U(V) in the aqueous phase. A few extremely heavy bicarbonate-extracted δ238U values were due to mass-dependent fractionation resulting from several hypothesized mechanisms. The results suggest the preferential accumulation of the heavy isotope in the reduced species and the significant influence of U(V) on the overall isotopic fractionation, providing insight into the U isotope fractionation behavior during its abiotic reduction process.

Proteomic Analyses of the Mouse Brain.

Proteomics is a scientific field that aims to identify and characterize all proteins within a biological system, including their posttranslational modifications (PTMs), quantitative changes, and protein-protein interactions. Over the last two decades, proteomic approaches have been widely used in neuroscience research, providing multidimensional insights into the biology and pathology of the brain.Here, we present a basic protocol for profiling protein expression in the mouse brain, which involves total protein extraction, fractionation, digestion, and identification through liquid chromatography coupled with tandem mass spectrometry (LC-MS/MS). This method is compatible with many prevalent techniques used for protein quantitation, PTM analysis, and protein-protein interaction mapping.

Differences in physicochemical properties of pectin extracted from pomelo peel with different extraction techniques.

In order to obtain high yield pomelo peel pectin with better physicochemical properties, four pectin extraction methods, including hot acid extraction (HAE), microwave-assisted extraction (MAE), ultrasound-assisted extraction, and enzymatic assisted extraction (EAE) were compared. MAE led to the highest pectin yield (20.43%), and the lowest pectin recovery was found for EAE (11.94%). The physicochemical properties of pomelo peel pectin obtained by different methods were also significantly different. Pectin samples obtained by MAE had the highest methoxyl content (8.35%), galacturonic acid content (71.36%), and showed a higher apparent viscosity, thermal and emulsion stability. The pectin extracted by EAE showed the highest total phenolic content (12.86%) and lowest particle size (843.69 nm), showing higher DPPH and ABTS scavenging activities than other extract methods. The pectin extracted by HAE had the highest particle size (966.12 nm) and degree of esterification (55.67%). However, Fourier-transform infrared spectroscopy showed that no significant difference occurred among the different methods in the chemical structure of the extracted pectin. This study provides a theoretical basis for the industrial production of pomelo peel pectin.

Ultrasonic-assisted extraction of polysaccharide from Paeoniae Radix alba: Extraction optimization, structural characterization and antioxidant mechanism in vitro.

Paeoniae Radix alba is used in Traditional Chinese Medicine for the treatment of gastrointestinal disorders, immunomodulatory, cancer, and other diseases. In the current study, the yield of Paeoniae Radix alba polysaccharide (PRP) was significantly increased with optimal ultrasound-assisted extraction compared to hot water extraction. Further, an acidic polysaccharide (PRP-AP) was isolated from PRP after chromatographic separation and was characterized as a typical pectic polysaccharide with side chains of arabinogalactans types I and II. Moreover, it showed antioxidant effects on LPS-induced damage on IPEC-J2 cells determined by qRT-PCR and ELISA, including decreasing the pro-inflammatory factors' expressions and increasing the antioxidant enzymes activities, which was shown to be related to the Nrf2/Keap1 pathway modulated by PRP-AP. The metabolites change (such as itaconate, cholesterol sulfate, etc.) detected by untargeted metabolomic analysis in cells was also shown to be modulated by PRP-AP, and these metabolites were further utilized and protected cells damaged by LPS. These results revealed the cellular active mechanism of the macromolecular PRP-AP on protecting cells, and supported the hypothesis that PRP-AP has strong benefits as an alternative dietary supplement for the prevention of intestinal oxidative stress by modulating cellular metabolism.