[Determination of six halogenated solvent residues in olive oil by headspace gas chromatography].

The residual amount of halogenated solvents in olive oil is an important indicator of its quality. The National Olive Oil Quality Standard GB/T 23347-2021 states that the residual amount of individual halogenated solvents in olive oil should be ≤0.1 mg/kg and that the total residual amount of halogenated solvents should be ≤0.2 mg/kg. COI/T.20/Doc. No. 8-1990, which was published by the International Olive Council, describes the standard method used for the determination of halogenated solvents in olive oil. Unfortunately, this method is cumbersome, has poor repeatability and low automation, and is unsuitable for the detection and analysis of residual halogenated solvents in large quantities of olive oil. At present, no national standard method for determining residual halogenated solvents in olive oil is available in China. Thus, developing simple, efficient, accurate, and stable methods for the determination of residual halogenated solvents in olive oil is imperative. In this paper, a method based on automatic headspace gas chromatography was established for the determination of residual halogenated solvents, namely, chloroform, carbon tetrachloride, 1,1,1-trichloroethane, dibromochloromethane, tetrachloroethylene, and bromoform, in olive oil. The samples were processed as follows. After mixing, 2.00 g (accurate to 0.01 g) of the olive oil sample was added into a 20 mL headspace injection bottle and immediately sealed for headspace gas chromatography analysis. Blank virgin olive oil was used to prepare a standard working solution and the external standard method for quantification. The solvents used in the preparation of halogenated solvent standard intermediates were investigated and methanol was selected as a replacement for N,N-dimethylacetamide to prepare a halogenated solvent standard intermediate owing to its safety. The effects of different injection times (1, 2, 3, 4, 5, 6 s), equilibration temperatures (60, 70, 80, 90, 100, 110, 120 ℃), and equilibration times (4, 5, 8, 10, 20, 30, 40 min) of the headspace sampler on the detection of the residual amounts of the six halogenated solvents were investigated. The optimal injection time and equilibration temperature were 3 s and 90 ℃, respectively. The method demonstrated good analytical performance for the six halogenated solvents when the equilibration time was 30 min. A methodological study was conducted on the optimized method, and the results showed that the six halogenated solvents exhibited good linear relationships in the range of 0.002-0.200 mg/kg, with correlation coefficients of ≥0.9991. The limits of detection (LODs) and quantification (LOQs) of 1,1,1-trichloroethane and bromoform were 0.0006 and 0.002 mg/kg, respectively. The LODs and LOQs of chloroform, carbon tetrachloride, dibromochloromethane, and tetrachloroethylene were 0.0003 and 0.001 mg/kg, respectively. The average recoveries under different spiked levels were 85.53%-115.93%, and the relative standard deviations (n=6) were 1.11%-8.48%. The established method was used to analyze 13 olive oil samples available in the market. Although no halogenated solvents were detected in these samples, a limited number of samples does not represent all olive oils. Hence, monitoring residual halogenated solvents in olive oil remains necessary for its safe consumption. The LOQs of the method for the six halogenated solvents were significantly lower than that of the COI/T.20/Doc. No. 8-1990 standard method (0.02 mg/kg). In addition, the developed method can be conducted under short operation times with high precision and degree of automation as well as good accuracy. Thus, the proposed method is suitable for the determination and analysis of the residues of the six halogenated solvents in large batches of olive oil samples.

Exposure to disinfection by-products and risk of cancer: A systematic review and dose-response meta-analysis.

Disinfection by-products (DBPs), including trihalomethanes (THMs) and haloacetic acids (HAAs), have attracted attention due to their carcinogenic properties, leading to varying conclusions. This meta-analysis aimed to evaluate the dose-response relationship and the dose-dependent effect of DBPs on cancer risk. We performed a selective search in PubMed, Web of Science, and Embase databases for articles published up to September 15th, 2023. Our meta-analysis eventually included 25 articles, encompassing 8 cohort studies with 6038,525 participants and 10,668 cases, and 17 case-control studies with 10,847 cases and 20,702 controls. We observed a positive correlation between increased cancer risk and higher concentrations of total trihalomethanes (TTHM) in water, longer exposure durations, and higher cumulative TTHM intake. These associations showed a linear trend, with relative risks (RRs) and 95 % confidence intervals (CIs) being 1.02 (1.01-1.03), 1.04 (1.02-1.06), and 1.02 (1.00-1.03), respectively. Gender-specific analyses revealed slightly U-shaped relationships in both males and females, with males exhibiting higher risks. The threshold dose for TTHM in relation to cancer risk was determined to be 55 µg/L for females and 40 µg/L for males. A linear association was also identified between bladder cancer risk and TTHM exposure, with an RR and 95 % CI of 1.08 (1.05-1.11). Positive linear associations were observed between cancer risk and exposure to chloroform, bromodichloromethane (BDCM), and HAA5, with RRs and 95 % CIs of 1.02 (1.01-1.03), 1.33 (1.18-1.50), and 1.07 (1.03-1.12), respectively. Positive dose-dependent effects were noted for brominated THMs above 35 µg/L and chloroform above 75 µg/L. While heterogeneity was observed in the studies for quantitative synthesis, no publication bias was detected. Exposure to TTHM, chloroform, BDCM, or HAA5 may contribute to carcinogenesis, and the risk of cancer appears to be dose-dependent on DBP exposure levels. A cumulative effect is suggested by the positive correlation between TTHM exposure and cancer risk. Bladder cancer and endocrine-related cancers show dose-dependent and positive associations with TTHM exposure. Males may be more susceptible to TTHM compared to females.

Multiple liquid-liquid extraction of dissolved compounds in immortelle hydrosol with four different solvents.

Immortelle, a revered Mediterranean medicinal plant, is celebrated for its potent essential oil renowned in the cosmetic industry for its skin-enhancing properties. Yet, immortelle hydrosol, an often-overlooked byproduct, holds promise in cosmetics due to its compatibility with polar active ingredients. This study investigates the chemical composition of immortelle hydrosol by employing liquid-liquid extraction (LLE) to transfer volatile organic components into nonpolar solvents. Four solvents - chloroform, dichloromethane, hexane, and benzene - were assessed through ten consecutive extractions from industrially produced immortelle hydrosol. Quantification was achieved using GC analysis with tetradecane as an internal standard. Chloroform emerged as the most efficient solvent, yielding 2447.0 mg/L of volatile compounds, surpassing dichloromethane, hexane, and benzene. Key compounds in immortelle hydrosol included 3-pentanone, 2-methyl-1-butanol, and γ-terpineol. Importantly, the study revealed that a portion of essential oil compounds persists in the hydrosol even after ten LLE cycles, with optimal results achievable in five extractions (~92 % in most cases).

Analysis of Volatile Constituent by Hydrodistillation and Solid-Phase Microextraction Techniques and Antimicrobial and Scolicidal Activities of Essential Oil and Soxhlet Extracts of Ulva rigida grown in Turkey.

In the present study, the volatile composition of Ulva rigida (U. rigida) was elucidated by two different methods. As a result of the identification process of volatile components using the GC/MS-FID instrument, 31 compounds were identified by hydrodistillation (HD) method, and 15 compounds were identified by solid-phase microextraction (SPME) method, elucidating the structure of 99.86 % and 92.65 %, respectively. The most abundant compounds in the essential oil of U. rigida were n-hexadecanoic acid and pentadecanal, while the most abundant compound according to the SPME analysis was heptadecyne, a hydrocarbon compound. In the next step, hexane, dichloromethane, chloroform and methanol solvent extracts of U. rigida were prepared and the antimicrobial activities of the extracts and the essential oil obtained by hydro-distillation as well as the scolicidal activities of the solvent extracts were determined. The results of the antimicrobial activity test of the essential oil showed a high level of activity against Bacillus cereus ATCC 10876 and MRSA. The highest activity was found on the microorganism of Pseudomonas aeruginosa ATCC 9027 in chloroform and methanol extracts of U. rigida. Furthermore, viability detection was performed and the scolicidal effects of the extracts on protoscoleces were assessed. The values of lethal concentration doses (LD50 , LD75 and LD90 ) were calculated using probit analysis.

Chemical markers in marine food web: A simple workflow based on methyl tert-butyl ether extraction for fatty acids and stable isotopes assessment in plankton samples.

Fatty acids (FAs) are used, often in combination with stable isotopes (SIs), as chemical biomarkers to assess the contribution of different prey to the diet of consumers and define food web structure and dynamics. Extraction of lipids is traditionally carried out using methanol (MeOH) combined with chloroform or dichloromethane, these latter being well-known environmental pollutant and potential carcinogenic agents. Recently, extraction protocols based on methyl tert-butyl ether (MTBE) and MeOH have been proposed as an alternative to halogenated solvents in lipidomic studies. However, no specific investigation has been performed to assess MTBE suitability in marine ecological studies including FA analysis together with SI measurements. We used an analytical workflow for qualitative and quantitative analysis of FAs and SIs in field samples of phytoplankton, zooplankton and the scyphomedusa Pelagia noctiluca, applying MTBE in comparison with chloroform- and dichloromethane-based protocols for total lipid extraction. Our analysis suggested that MTBE is a reliable substitute for lipid extraction in trophic ecology studies in marine planktonic organisms.

Chloroform exposure in air and water in Swedish indoor swimming pools-urine as a biomarker of occupational exposure.

INTRODUCTION: Disinfection by-products are produced in water disinfected with chlorine-based products. One such group is trihalomethanes, and chloroform is the most abundant trihalomethane in swimming pool areas. Chloroform can be absorbed by inhalation, ingestion, and dermal absorption, and is classified as possibly carcinogenic. AIM: To investigate if chloroform concentrations in air and water affect the chloroform concentration in urine samples of exposed swimming pool workers. METHODS: Workers from 5 adventure indoor swimming pools carried personal chloroform air samplers and provided up to 4 urine samples during one workday. Chloroform concentrations were analyzed with a linear mixed model analysis to investigate a possible correlation between air and urine concentrations. RESULTS: The geometric mean chloroform concentration was 11 µg/m3 in air and 0.009 µg/g creatinine in urine among individuals with ≤2 h at work, 0.023 µg/g creatinine among those with >2-5 working hours, and 0.026 µg/g creatinine in the group with >5-10 working hours. A risk of higher levels of chloroform in urine was associated with longer hours at work (≤2 h versus >5-10 h, odds ratio [OR] 2.04, 95% confidence interval [CI] 1.25-3.34), personal chloroform concentrations in air (≤17.00 µg/m3 versus >28.00 µg/m3, OR 9.23, 95% CI 3.68-23.13) and working at least half the working day near the swimming pools (OR 3.16, 95% CI 1.33-7.55). Executing work tasks in the swimming pool water was not associated with higher chloroform concentrations in urine compared to only working on land (OR 0.82, 95% CI 0.27-2.45). CONCLUSION: There is an accumulation of chloroform concentrations in urine during a workday and a correlation between personal air and urine concentrations of chloroform among workers in Swedish indoor swimming pools.

Modelling chloroform in indoor swimming pool air and water: the influences of internal air circulation and occupants.

The release of chloroform from water to air in an indoor swimming pool (ISP) exhibits complex physicochemical interactions among many variables, including environmental conditions, occupant activities, and geometry of the ISP. By combining the relevant variables, a structured mathematical model, the double-layer air compartment (DLAC) model, was developed to predict the level of chloroform in ISP air. A physical parameter, the indoor airflow recycle ratio (R), was incorporated into the DLAC model due to internal airflow circulation resulting in the ISP structural configuration. The theoretical R-value for a specific indoor airflow rate (vy) can be found by fitting the predicted residence time distribution (RTD) to the simulated RTD from computational fluid dynamics (CFD), showing a positive linear relationship with vy. The mechanical energies induced by occupant activities were converted into a lumped overall mass-transfer coefficient to account for the enhanced mass transfer of chloroform from the water into the air and mixing in ISP air. The DLAC model predicted that chloroform air concentrations were statistically less accurate without considering the influence of R compared with the online open-path Fourier transform infrared measurements. A novel index, the magnitude of emission (MOE) from swimmers, was linked to the level of chloroform in ISP water. The capability of the DLAC model associated with the MOE concept may facilitate upgrading the hygiene management of ISPs, including the ability to administer necessary chlorine additives in pool water and monitor the chloroform in ISP air.

Release regularity and cleaning measures of magnetic anion exchange resin during application.

Anion exchange resin is responsible for removing harmful anionic contaminants in drinking water treatment, but it may become a significant source of precursors for disinfection byproducts (DBPs) by shedding material during application without proper pretreatment. Batch contact experiments were performed to investigate the dissolution of magnetic anion exchange resins and their contribution to organics and DBPs. Dissolved organic carbon (DOC) and dissolved organic nitrogen (DON) released from the resin were highly correlated with the dissolution conditions (contact time and pH), in which 0.7 mg/L DOC and 0.18 mg/L DON were distributed at exposure time of 2 h and pH 7. The formation potential of four DBPs in the shedding fraction was also revealed that trichloromethane (TCM), dichloroacetonitrile (DCAN), nitrosodimethylamine (NDMA), and dichloroacetamide (DCAcAm) concentrations could reach 21.4, 5.1, 12.1 µg/L, and 69.6 ng/L, respectively. Furthermore, the hydrophobic DOC that preferred to detach from the resin mainly originated from the residues of crosslinkers (divinylbenzene) and porogenic agents (straight-chain alkanes) detected by LC-OCD and GC-MS. Nevertheless, pre-cleaning inhibited the leaching of the resin, among which acid-base and ethanol treatments significantly lowered the concentration of leached organics, and formation potential of DBPs (TCM, DCAN, and DCAcAm) below 5 µg/L and NDMA dropped to 10 ng/L.

Value-added processing of seeds from tomato sauce industry and comparison of extraction solvents on the chemical properties.

BACKGROUND: Tomato seed oil (TSO) was obtained using a combined method of pre-keeping in solvent and Soxhlet extraction. A considerable oil yield could not be obtained using samples without drying or grinding, with dried or non-dried seeds, which were not kept in solvent (<2%). For this purpose, oil yield, physicochemical properties, oxidation values, spectrophotometric indices and fatty acid composition of the samples extracted with acetone, ethyl acetate, chloroform and petroleum ether were determined. RESULTS: Oils obtained by the extraction of petroleum ether (20.36 meq g O2 kg-1 ) and ethyl acetate (11.16 meq g O2 kg-1 ) were found to have very high peroxide values. Besides, a high-quality edible oil should have an anisidine value (p-AnV) of less than 10. Samples extracted with chloroform alone had a p-AnV of 8.86, while slightly higher values were found for other samples (P < 0.05). Chloroform (20.50) and acetone (23.06) both gave the best results and met the expected value, with total oxidation value below 30. Finally, the highest levels of primary fatty acids observed were linoleic acid (32.77-41.95%), palmitic acid (23.75-32.27%), oleic acid (16.17-24.52%), and stearic acid (7.76-12.82%). CONCLUSION: This process is applicable to recycling tomato sauce waste and essential oil. The research proved that the seed-drying process and pre-keeping in solvent have an important effect on oil yield, quality and fatty acid composition. © 2023 Society of Chemical Industry.

Algae impacted drinking water: Does switching to chloramination produce safer drinking water?

Harmful algal (cyanobacterial) blooms (HABs) are increasing throughout the world. HABs can be a direct source of toxins in freshwater sources, and associated algal organic matter (AOM) can act as precursors for the formation of disinfection by-products (DBPs) in drinking water. This study investigated the impacts of algae on DBP formation using treatment with chloramine, which has become a popular disinfectant in the U.S. and in several other countries because it can significantly lower the levels of regulated DBPs formed. Controlled laboratory chloraminations were conducted using live field-collected algal biomass dominated by either Phormidium sp. or Microseira wollei (formerly known as Lyngbya wollei) collected from Lake Wateree and Lake Marion, SC. Sixty-six priority, unregulated or regulated DBPs were quantified using gas chromatography (GC)-mass spectrometry (MS). The presence of HAB-dominated microbial communities in source waters led to significant increases in more toxic nitrogen-containing DBPs (1.5-5 fold) relative to lake waters collected in HAB-free waters. Compared to chlorinated Phormidium-impacted waters, chloraminated waters yielded lower total DBP levels (up to 123 µg/L vs. 586 µg/L for low Br-/I- waters), but produced a greater number of brominated, iodinated, and mixed halogenated DBPs in high Br-/I- waters. Among the DBPs formed in Phormidium-impacted chloraminated waters, dichloroacetic acid, trichloromethane, chloroacetic acid, chloropropanone, and dichloroacetamide were dominant. For Microseira wollei-impacted chloraminated waters, total DBP concentrations ranged from 33 to 145 µg/L (approximately 3-5 times lower than chlorination), with dichloroacetic acid, dichloroacetamide, and trichloromethane dominant. Overall, chloramination significantly reduced calculated cytotoxicity and genotoxicity in low Br- and I- waters, but produced 1.3 fold higher calculated cytotoxicity (compared to chlorine) with high Br-/I- waters due to increased formation of more toxic iodo- and mixed halogenated DBPs.

Analysis of Metaldehyde in Animal Whole Blood and Serum by Gas Chromatography-Mass Spectrometry.

Metaldehyde, a widely used molluscicide, is the third cause of intoxication by pesticides in domestic animals in Europe. Most mammalian species are susceptible, and its exposure may lead to death within a few hours. While metaldehyde intoxication diagnosis is in most cases presumptive, based on the symptomatology or from "postmortem" analysis, few analytical methods are currently available for live animals. The aim of this work was to describe a fast analytical method for the specific and quantitative determination of metaldehyde in animal whole blood and serum at concentrations of toxicological significance. A liquid-liquid extraction with chloroform and gas chromatography-mass spectrometry quantification are proposed. The method limit of quantification (LOQ) was 0.04 µg/mL in serum and whole blood. The method was linear in the range from 0.04 to 200 µg/mL. The recovery was between 93% and 102% for LOQ, low, medium and high spike concentrations. Intra- and inter-assay relative standard deviation was <12% in all spike concentrations in both serum and whole blood, apart from one of the experiments at LOQ in whole blood, which accounted for 17.7%. The method was applied to real intoxication cases, and the concentration found in positive samples was between 29 and 69 µg/mL. The proposed method provides high sensitivity, accuracy and precision and can be used to assist in the diagnosis of metaldehyde poisoning.

A simple method for analysis of vitamin A palmitate in fortified cereal products using direct solvent extraction followed by reversed-phase HPLC with UV detection.

Vitamin A is generally analysed using a time-consuming and possibly detrimental saponification step, followed by extraction and HPLC analysis. We here developed a new method to analyse retinyl palmitate (RP) (also known as vitamin A palmitate) without the need for saponification and validated it in model systems consisting of RP, soy oil and wheat bran, and in RP-fortified cereal products. Two direct solvent extraction protocols using acetone/methanol (7/3, v/v) or chloroform/methanol (1/1, v/v) were tested. After extraction, RP was quantified by reversed-phase HPLC with UV detection. The HPLC method had low limits of detection (0.01 µg/mL) and quantification (0.03 µg/mL). Both extraction protocols showed a good recovery (88-105 %) and intra-and inter-day precision (<5%) for RP extraction from the model systems. The obtained results corresponded to results obtained using a golden standard approach. For complex food matrices like bread and cookies, the chloroform/methanol extraction protocol showed the best performance characteristics.

Exposures to volatile organic compounds, serum vitamin D, and kidney function: association and interaction assessment in the US adult population.

The relationships of exposures to volatile organic compounds (VOCs) with vitamin D and kidney function remain unclear. Our analyses included 6070 adults from 2003 to 2010 survey cycles of the National Health and Nutrition Examination Survey to explore associations of six VOCs with serum vitamin D, albumin-to-creatinine ratio (ACR), and estimated glomerular filtration rate (eGFR). The results suggested that dibromochloromethane was positively associated with ACR, and chloroform was inversely associated with ACR. U-shaped associations of toluene, m-/p-xylene, bromodichloromethane, and 1,4-dichlorobenzene with ACR were observed. Toluene, m-/p-xylene, and 1,4-dichlorobenzene were associated with eGFR in U-shaped manners, while bromodichloromethane and chloroform were inversely associated with eGFR. Elevation in 1,4-dichlorobenzene was associated with decrease in vitamin D, while chloroform and m-/p-xylene were in U-shaped associations with vitamin D. VOCs mixture was U-shaped associated with ACR, inversely associated with eGFR, and inversely associated with vitamin D. Vitamin D was in a U-shaped association with ACR. Vitamin D significantly interacted with VOCs on the two kidney parameters. In the US adult population, exposures to VOCs were associated with kidney function and serum vitamin D level decline, and the serum vitamin D may have interaction effects with VOCs exposures on kidney function.

An assessment of DNA extraction methods from blood-stained soil in forensic science.

In forensic crime scene investigations, biological fluids such as blood are commonly found in soil. However, the analysis of blood-stained soil can be challenging due to the presence of inhibitors which limit the effective extraction and amplification of the deoxyribonucleic acid (DNA) required to produce a reportable DNA profile. There are some extraction methods that have been applied to blood-stained soil in forensic science, but these have produced sporadic results. This research has taken a number of different extraction methods from the fields of ancient DNA and environmental DNA and broken them down into the individual steps of pre-treatment, incubation, separation and purification. These steps were assessed independently then combined into various extraction methods to determine the best technique that can effectively and reliably profile human DNA from blood-stained soil. Testing involved assessment of three extraction buffers, (cetyltrimethylammonium bromide, guanidine thiocyanate, and proteinase K), four pre-treatment methods, (polyvinylpyrrolidone, ethylenediaminetetraacetic acid, hydrochloric acid, and sodium hydroxide), three separation steps, (centrifugation, phenol chloroform, and chloroform) and four purification steps, (size exclusion chromatography, bind elute columns, isopropanol precipitation and silica magnetic beads). The most effective procedure was found to be a polyvinylpyrrolidone pre-treatment with a proteinase K extraction buffer followed by magnetic silica bead purification with or without centrifugation. However, centrifugation separation was found to be equally effective after the pre-treatment step as after the incubation step. Our results shows that most of the current forensic procedures would benefit from the addition of a pre-treatment step prior to processing through the automated DNA profiling pipeline.

Phyto-metabolomics of phlogacanthus thyrsiformis by using LC-ESI-QTOF-MS/MS and GC/QTOF-MS: Evaluation of antioxidant and enzyme inhibition potential of extracts.

Phlogacanthus thyrsiformis (P. thyrsiformis) is a non-conventional edible plant that has been used as a vegetable and as a traditional medicine to treat various diseases. This non-conventional edible plant is widespread in India, Yunnan-Chinese provinces, and Vietnam. Despite this potential claim, the phytochemical investigation of plants remains incomplete. In the present study, the chemical profile analysis of P. thyrsiformis leaves extracts was performed using LC-ESI-QTOF-MS/MS and GC/QTOF-MS and assessed for its antioxidants and enzyme inhibitory potential. A cursory examination of the phytometabolites of different solvents extracts revealed chloroform extract has different metabolites, including phenols, terpenes, glycosides and alkaloids. 113 and 138 metabolites, including primary and secondary metabolites, were identified using LC-ESI-QTOF-MS/MS and GC/QTOF-MS, respectively. Total phenolic content was observed highest in chloroform extract (60.59 ± 1.25 mg GAE/g). Maximum antioxidant activity was found to be in chloroform extract, which was identified by DPPH (0.88 ± 0.29 mg/mL), ABTS (0.54 ± 0.1 mg/mL) and FRAP assay (26.46 ± 1.65 mg AA/g extract). Ethyl acetate extract have the highest α-amylase (0.09 ± 0.11 mg/mL) and α-glucosidase (0.088 ± 0.13 mg/mL) enzyme inhibition potential. For all the detected molecules, docking and molecular dynamics studies were performed. To the best of our knowledge, this is the first report that discusses LC-ESI-QTOF-MS/MS and GC/QTOF-MS-based metabolites profiling of P. thyrsiformis that can help to treat various diseases.

Effect of dissolved organic matter and its fractions on disinfection by-products formation upon karst surface water.

In this study, disinfection by-products (DBP) formation from dissolved organic matter (DOM) and its fractions, including both hydrophilic and hydrophobic components, were investigated at a typical karst surface water. The subsequent DBP formation potential was evaluated by deducing chemical characteristics of DOM fractions and representative algal organic matter (Chlorella sp. AOM) under the influence of divalent ions (Ca2+ and Mg2+) via spectra analysis. Both terrigenous and autochthonous DOM performed as critical DBP precursors, and DBP formation patterns were tightly correlated to organic matter chemical variations. DBP formation was significantly higher in drought period compared to that in wet period (P < 0.05). Particularly, trichloromethane (TCM) and dichloroacetonitrile (DCAN) showed distinct formation patterns compared to the scenarios in non-karst water. For DOM fractions, hydrophobic components showed higher DBP formation compared to hydrophilic counterparts, hydrophilic neutral enriched more reactive organic nitrogen for N-DBPs production. It was preferable to enrich humic-like substances after Ca2+ and Mg2+complexation in Chlorella sp. AOM, TCM formation increased whereas DCAN production remained unchanged in the presence of divalent ions. This study innovatively provided a linkage between chemical characteristics of DOM and understanding of DBP formation in karst surface water.

Assessment of Bacterial Diversity of Industrial Poultry Wastewater by Denaturing Gradient Gel Electrophoresis (DGGE) and the Cultivation Method in Order to Inform Its Reuse in Agriculture.

Effluents discharged by poultry meat industries are heavily polluted with raw materials, such as fat, blood residues, and proteins. Thus, untreated effluents directly discharged into the environment may constitute a public health threat. This study aims to evaluate the bacterial diversity of three water qualities: industrial poultry wastewater (PWW), tap water (TW), and PWW diluted with TW (50 : 50) (V/V) (TWPWW) by the combination of culture-independent and culture-dependent approaches. The total bacterial DNA was extracted using phenol/chloroform method. The hypervariable 16S rRNA region V3-V5 was amplified by PCR using universal primers. The amplicons were separated by vertical electrophoresis on a polyacrylamide gel of increasing denaturing gradient according to their richness in GC bases. Selected bands were reamplified and sequenced. Pure isolated bacteria from nutrient agar medium were characterized according to their morphological and biochemical characteristics. Genomic DNA from pure strains was extracted by boiling method, and a molecular amplification of the 16S-23S ITS region of the 16S rRNA gene was performed using the universal primers. Selected isolates were identified by sequencing. Results showed a high bacterial load and diversity in PWW in comparison with TW and TWPWW. A collection of 44 strains was obtained, and 25 of them were identified by sequencing. Proteobacteria represented 76% of isolated bacteria Gamma-Proteobacteria was the predominate isolate (68%). Other isolates were Firmicutes (8%), Bacteroidetes (12%), and Actinobacteria (8%). These isolates belong to different genera, namely, Pseudomonas, Acinetobacter, Proteus, Empedobacter, Corynebacterium, Enterobacter, Comamonas, Frondibacter, Leclercia, Staphylococcus, Atlantibacter, Klebsiella, and Microbacterium.

Assessing volatile organic compounds exposure and prostate-specific antigen: National Health and Nutrition Examination Survey, 2001-2010.

Background: Volatile organic compounds (VOCs) are a large group of chemicals widely used in people's daily routines. Increasing evidence revealed the VOCs' accumulating toxicity. However, the VOCs toxicity in male prostate has not been reported previously. Thus, we comprehensively evaluated the association between VOCs and prostate-specific antigen (PSA). Methods: A total of 2016 subjects were included in our study from the National Health and Nutrition Examination Survey with VOCs, PSA, and other variables among U.S. average population. We constructed XGBoost Algorithm Model, Regression Model, and Generalized linear Model (GAM) to analyze the potential association. Stratified analysis was used to identify high-risk populations. Results: XGBoost Algorithm model identified blood chloroform as the most critical variable in the PSA concentration. Regression analysis suggested that blood chloroform was a positive association with PSA, which showed that environmental chloroform exposure is an independent risk factor that may cause prostate gland changes [ß, (95% CI), P = 0.007, (0.003, 0.011), 0.00019]. GAM observed the linear relationship between blood chloroform and PSA concentration. Meanwhile, blood chloroform linear correlated with water chloroform in the lower dose range, indicating that the absorption of water may be the primary origin of chloroform. Stratified associations analysis identified the high-risk group on the chloroform exposures. Conclusion: This study revealed that blood chloroform was positively and independently associated with total PSA level, suggesting that long-term environmental chloroform exposure may cause changes in the prostate gland.

Volatile organic compounds in water matrices: Recent progress, challenges, and perspective.

Volatile organic compounds (VOCs) are a group of organic compounds that have a molecular structure containing carbon and their chemical properties allow them to be easily converted to steam and gas and remain for a long period of time and have diverse effects on the environment. The purpose of this study is determination of the concentration of VOCs such as alachlor, anthracene, benzene, bromoform, chloroform, heptachlor, isophorone, tetrachloroethylene, γ -chlordane, toluene, etc. in water matrices. The results showed that among studies conducted on VOCs, the concentration of tetrachloroethylene, m,p-xylene, and toluene were at the top in water matrices, and the lowest average concentrations were found in chloroform, anthracene, and butyl benzyl phthalate. In terms of VOC concentrations in water matrices, China was the most polluted country. Moreover, the data analysis indicated that China was the only country with carcinogenic risk. A Monte-Carlo simulation showed that although the averages obtained were comparable to the acceptable limits, for heptachlor, the maximum carcinogenic risk is achieved at a level that is slightly over the limit, only 25% from the population being exposed.

Evaluation of different DNA extraction methods based on steel-bullet beating for molecular diagnosis of onychomycosis.

BACKGROUND: Considering increased trends toward molecular methods for detection/identification of fungi causing onychomycosis, the aim of this study is comparison three DNA extraction methods based on steel-bullet beating to extract DNA from nail. METHODS: Ex -vivo onychomycosis model was developed using bovine hoof with Candida albicans and Aspergillus flavus. For two models, total DNA was extracted using the three different methods. In method 1, the extraction and purification were performed by steel-bullet beating and phenol chloroform protocol, respectively. In method 2, a freezing step were applied before beating. The purification step in method 3 was carried out using a commercial kit, although DNA extraction was done similarly to method 1 in that approach. To evaluate the efficacy of each method, the extracted genomic DNA was amplified with Polymerase Chain Reaction (PCR) using Internal Transcribed Spacer (ITS) regions. Moreover, 50 nail samples were evaluated for onychomycosis using direct microscopy examination as well as PCR in order to evaluate the diagnostic efficiency of the optimal DNA extraction method. RESULTS: Regarding the desirable quality of the extracted DNA, cost effectiveness, and simplicity, method 1 could be used to extract DNA effectively. Additionally, the obtained data showed that PCR had a higher detection rate of fungal agents in the nail samples than direct microscopic examination. CONCLUSIONS: This study demonstrated that the mechanical disruption of the cell wall by steel-bullet beating is a useful and practical method to improve the quantity and quality of fungal DNA thorough the extraction process.