Evaluation of nanohardness, elastic modulus, and surface roughness of fluoride-releasing tooth colored restorative materials.

Recently, interest in tooth-colored fluoride-releasing dental materials has increased. Although physical and mechanical properties such as surface hardness, elastic modulus and surface roughness of the restorative materials have been investigated, the effect of different immersion media on these properties is still controversial. The aim of this study was to evaluate the nanohardness, elastic modulus and surface roughness of the fluoride release of tooth-colored restorative materials after immersion in acidic beverages. Prepared samples of three restorative materials (a highly viscous glass ionomer (EQUIA Forte; GC, Tokyo, Japan), a compomer (Dyract XP; Dentsply, Weybridge, UK), and a bioactive restorative material (Activa BioACTIVE; Pulpdent, MA, USA)) were randomly divided and immersed in distilled water, a cola and an orange juice for one week. The HYSITRON T1 950 TriboIndenter device (Hysitron, USA) with the Berkovich diamond indenter tip was used for all measurements. The nanohardness and elastic modulus of the samples were measured by applying a force of 6000 µN to five different points on the sample surface. Surface roughness measurements were evaluated on random samples by scanning five random 40 × 40 µm areas. The properties were measured at the initial and one week after immersion. The values of nanohardness, elastic modulus and surface roughness were tested for significant differences using a two-way analysis of variance (ANOVA) with repeated measures (p < 0.05). Tukey's honest significant difference (HSD) test was used for multiple comparisons. AB (Activa BioACTIVE) had the highest initial mean values for nanohardness. After post-immersion, the highest mean value for elastic modulus was the initial AB value. The lowest mean value for roughness of 100.36 nm was obtained for the initial DX (Dyract XP) measurement. Acidic beverages had a negative effect on the nanohardness, elastic modulus and surface roughness of the restorative materials.

Comparative analysis of shear bond strength of MTA and Theracal PT with different restorative materials.

BACKGROUND: This study aimed to compare the in vitro shear bond strength (SBS) of mineral trioxide aggregate (MTA) and dual-cured, resin-modified calcium silicate material (Theracal PT) to composite resin, compomer, and bulk-fill composite, and to evaluate the bond failure mode under a stereomicroscope. METHODS: Ninety acrylic specimens, each with a 4 mm diameter and 2 mm height central hole, were prepared. These specimens were randomly divided into two groups based on the capping materials: MTA and Theracal PT. Each group was further subdivided into three subgroups (n = 15) according to the restorative materials: composite resin, compomer, and bulk-fill composite. The specimens were then subjected to shear testing using a universal testing machine at a crosshead speed of 1 mm/min. Post-test, the fracture locations were examined using a stereomicroscope. Data were analyzed using a two-way analysis of variance (ANOVA) and the Tukey test. RESULTS: The SBS values for the Theracal PT group were significantly higher than those for the MTA group (p < 0.001). Within the MTA groups, no significant differences were observed in SBS values across the different restorative materials. However, a significant difference was found between the mean SBS values of the Theracal PT + composite resin group and the Theracal PT + compomer group (p < 0.001). CONCLUSIONS: Theracal PT shows promise in dentistry due to its superior bond strength. Given its bond values, Theracal PT appears capable of forming durable and long-lasting restorations by establishing reliable bonds with various restorative materials commonly used in dentistry.

Comparative evaluation of probiotic solutions on surface roughness and microhardness of different restorative materials and enamel.

This research study aimed to investigate the impact of probiotic mouthwash and kefir on the surface characteristics, specifically surface roughness and microhardness, of different restorative materials, as well as permanent and deciduous tooth enamels. Thirty disc-shaped specimens were prepared from composite resin (G-ænial Posterior (GP)), polyacid-modified composite resin (compomer) (Dyract-XP (DXP)), and resin-modified glass ionomer cement (Ionoseal (IS)). Additionally, thirty specimens of enamel were obtained from permanent teeth (PT) and thirty from deciduous teeth (DT) by embedding buccal and lingual sections, acquired through vertical sectioning of 15 permanent and 15 deciduous human tooth crowns in the mesiodistal orientation within acrylic resin blocks. The specimens were then categorized into three distinct groups and immersed for 14 days in one of the following solutions: distilled water, kefir or probiotic mouthwash. The mean surface roughness values of all specimens were assessed using an atomic force microscope, while the mean surface microhardness was measured using a Vickers hardness measuring instrument. The results revealed a statistically significant difference in mean surface roughness among the various restorative materials (p < 0.001). Among the restorative materials, the IS material exhibited notably higher mean surface roughness values than other restorative materials and tooth enamel, while no significant differences were observed between the PT and DT groups. Importantly, the main effect of the solutions under investigation was not statistically significant (p = 0.208). No significant difference was found between the surface roughness values of specimens subjected to the different solutions. When evaluating the effects of materials and solutions on microhardness, the main effects of material and solution variables and the influence of material-solution interactions were statistically significant (p < 0.001). Taken together, these results indicate that consistent use of kefir or probiotic mouthwashes may impact the surface properties of various restorative materials and tooth enamel.

Effect of Bonding Agents on the Shear Bond Strength of Tooth-colored Restorative Materials to Dentin: An In Vitro Study.

AIM: The aim of the study is to determine the difference in the shear bond strengths to dentin among dental composite (Filtek Z350®, 3M), compomer (Dyract Flow®, Dentsply) and Giomer (Beautifil®, Shofu) with 3MTM Single BondTM Universal Adhesive (SBU) (7th generation, self-etch, single solution adhesive) and AdperTM Single Bond 2 Adhesive (ASB) (5th generation, total-etch, two solution adhesive). MATERIALS AND METHODS: Sixty extracted human permanent teeth were collected, cleansed of debris, and placed in distilled water. The samples were segregated into two groups depicting the two bonding agents-AdperTM (ASB) and 3MTM Single Bond Universal (SBU) and sub-grouped into three groups depicting the three restorative materials (Composite, Giomer, and Compomer) used. Groups were respresented as follows: Group I-ASB + Composite; Group II-ASB + Giomer; Group III-ASB + Compomer; Group IV-SBU + Giomer; Group V-SBU + Compomer; Group VI-SBU + Composite. After applying the bonding agent as per the manufacturer's instructions, following which the restorative material was placed. A Universal Testing Machine (Instron 3366, UK) was employed to estimate the shear bond strength of the individual restorative material and shear bond strengths were calculated. RESULTS: Composite bonded with SBU (group VI) displayed the greatest shear strength (11.16 ± 4.22 MPa). Moreover, Giomers and flowable compomers displayed better bond strengths with ASB compared with their SBU-bonded counterparts. CONCLUSION: These results mark the importance of careful material selection in clinical practice and the bonding agent used to achieve optimal bond strength and enhance the clinical longevity and durability of dental restorations. CLINICAL SIGNIFICANCE: From a clinical perspective, to avoid a compressive or a shear failure, it would be preferrable to use a direct composite restorative material with SBU (Single bond universal adhesive, 7th generation) to achieve maximum bond strength. How to cite this article: Kuchibhotla N, Sathyamoorthy H, Balakrishnan S, et al. Effect of Bonding Agents on the Shear Bond Strength of Tooth-colored Restorative Materials to Dentin: An In Vitro Study. J Contemp Dent Pract 2024;25(3):245-249.

The chemical and optical stability evaluation of injectable restorative materials under wet challenge.

OBJECTIVES: To investigate and compare the chemical and optical stability of four restorative composite materials: two injectable resins, one flowable resin and one compomer. METHODS: Two injectable nano-filled composite resins: G-aenial Universal (GU) and Beautifil Injectable XSL (BI), a flowable composite resin: Filtek Supreme Flowable (FS) and a compomer: Dyract Flow (DF), in A2 shade were tested and compared. Water sorption and solubility were conducted according to ISO4049:2019 standard; ICP-OES and F-ion selective electrode were used to test the elemental release; Degree of conversion (DC) was obtained by using FTIR; water contact angle was obtained by static sessile drop method, and a spectrophotometer was used for optical properties (ΔE⁎, ΔL⁎ and TP). SPSS 28.0 was used for statistical analysis and the significant level was pre-set as α = 0.05. RESULTS: GU performed the best in water sorption and solubility, FS had the lowest elemental release, the best colour stability, and the highest DCIM and DC24-h. DF, the compomer had the lowest, and GU and BI, the injectable composites had the largest water contact angle, respectively. Correlations were found between water sorption and water solubility. CONCLUSIONS: The four composite restorative materials showed different chemical and optical behaviours. Overall, composite resins performed better than compomer, while additional laboratory and in vivo tests are necessary to obtain a more comprehensive comparison between injectable and flowable composite resins. Wsp and Wsl are influenced by many common factors, and the values are highly positively related. CLINICAL SIGNIFICANCE: A comprehensive understanding of materials is crucial before selecting materials for clinical practice. Composite resins rather than compomers are recommended because of their exceptional properties, which make them eligible for a wide range of clinical applications and an elongated lifespan.

Residual Monomer Release after the Polymerization of Different-Colored Flowable Compomer.

BACKGROUND: Compomers are restorative materials commonly used in pediatric dentistry. It is important to investigate the monomer release of materials used especially in pediatric patients. The aim of this study was to evaluate the residual monomer released from different-colored flowable compomers at five polymerization times. MATERIALS AND METHODS: Three experimental groups were formed: Group 1: pink flowable compomer (Twinky Star, VOCO, Germany), Group 2: blue flowable compomer (Twinky Star, VOCO), Group 3: white flowable compomer, A2 color of Dyract XP (Dentslpy DeTrey, Konstanz, Germany). For each group, samples were prepared using standard cylindrical Teflon molds (n = 10), and the compomers were cured using a light-emitting diode (LED) source in accordance with the manufacturer's recommendations. During each time period, the number of residual monomers: bisphenol-A glycidyl methacrylate (bis-GMA), urethane dimethacrylate (UDMA), hydroxyethyl methacrylate (HEMA), and triethylene glycol dimethacrylate (TEGDMA) were determined with high-performance liquid chromatography (HPLC). All data were analyzed statistically. RESULTS: In all groups, the amount of residual monomers increased after 1-h release periods (P < 0.05). For 2 weeks, the total residual monomers released were determined at most in Group 3 and at least in Group 1. However, there was no significant difference between the groups in terms of released amounts of monomers (P > 0.05). CONCLUSIONS: According to the study, when the total amount of residual monomer released from all groups was compared, no difference was found and it was observed that none of them exceeded the toxic dose. Flowable colored compomers can be used as safely as white compomers in pediatric dentistry.

Effect of topical fluoride applications on residual monomer release from resin-based restorative materials.

BACKGROUND: The effects of topical fluoride applications on the release of monomer ingredients from resin-based dental materials by immersion in various extraction solutions are unclear. The aim of this study was to determine the effect of topical fluorides (APF and NaF) on the elution of residual monomers (Bis-GMA, TEGDMA, UDMA, and HEMA) from resin-based materials. METHODS: Ninety specimens were prepared, 30 bulk-fill composite resin, 30 nanohybrid universal composite resin, and 30 polyacid-modified composite resin (compomer). These were randomly divided into three groups based on fluoride application procedures. Each specimen was kept in 75% ethanol solution, and residual monomers released from materials were analyzed using high-performance liquid chromatography (HPLC) after 10 min, 1 h, 24 h, and 30 days. The groups were compared using the Mann Whitney U and Kruskal Wallis tests. Measurements were analyzed using the Friedman and Wilcoxon signed-rank tests. RESULTS: Fluoride applications generally had no considerable effect on the amount of residual monomer released from resin-based restorative materials. The amount of monomer release after topical APF application was similar to the release in the control group and was lower than the release in the NaF group. The release of monomers from the resin-based material used in the study did not approach toxic levels at the applied time intervals. The compomer released lower amounts of monomer than other resin-based materials. CONCLUSIONS: Fluoride applications do not increase monomer release from resin-based restorative materials. However, compomers should be employed by clinicians due to their lower monomer release compared to other resin restorative materials. The release of monomers from all the resin-based materials did not approach toxic levels at the applied time intervals.

The cytotoxic and oxidative effects of restorative materials in cultured human gingival fibroblasts.

The aim of this study was to evaluate the cytotoxic and oxidative effects of the most commonly used dental restorative materials on human gingival fibroblast cells (HGFCs). HGFCs were obtained from healthy individuals. The tested restorative materials were a microhybrid resin based composite, a compomer resin, a glass ionomer cement, and an amalgam alloy. One hundred eight cylindirical samples, 10 mm in diameter and 2 mm in height, were prepared according to ISO 10993-12:2002 specifications (n = 9 in the tested subgroups). Freshly prepared and aged samples in artificial saliva at 37 °C (7 and 21 d) were placed into well plates and incubated. Wells without dental materials were constituted as the control group. After 72 h incubation period, cytotoxicity was determined using the neutral red (NR) assay. Oxidative alterations were assessed using total antioxidant capacity (TAC) and total oxidant status (TOS) assay kits. Data were analyzed using the ANOVA and LSD post hoc tests. All tested materials led to significant decreases in the cell viability rates (33-73%) compared to the control group. Glass ionomer and resin composite were found to be more cytotoxic than amalgam alloy and compomer. The highest TAC level was observed in glass ionomer after seven-day aging and these changes prevented an increase in TOS levels. Increases in TAC levels after seven-day aging in all groups exhibited significant differences with freshly prepared samples (p < 0.05). In all material groups, TOS levels of freshly prepared samples differed statistically and significantly from samples aged for 7 and 21 d (p < 0.05). The data obtained suggested that all the tested materials exhibited cytotoxic and pro-oxidant features. Freshly prepared samples caused higher TOS levels. However, oxidant status induced by materials decreased over time.

The evaluation of microleakage and fluoride release of different types of glass ionomer cements.

BACKGROUND: The aim of this study was to evaluate six different glass ionomer cement (GIC)-based restorative materials through comparisons of microleakage and fluoride release. MATERIALS AND METHODS: For microleakage, 30 teeth were randomly separated into 6 groups of 5: Group 1 (Dyract: compomer), Group 2 (Freedom: compomer), Group 3 (Equia: high-viscosity glass ionomer cements), Group 4 (Fuji IX: resin-modified glass ionomer cement), Group 5 (Ketac Molar: traditional glass ionomer cement [TGIC]) and Group 6 (Voco: TGIC). For fluoride release of six different GIC-based restorative materials, standard samples were prepared of 4 mm thickness and 7 mm diameter. A total of 60 samples were obtained as 10 samples from each group. The analyses were made using a Thermo Orion 720 A+ ionometer with the Orion fluoride electrode. At the end of 24 h, 72 h, 7 days, 14 days, and 30 days, the electrode was placed into the dish containing the sample, distilled water, and TISAB II; a reading was taken; and the value shown on the screen was recorded. RESULTS: For microleakage, a statistically significant difference was determined between the groups in respect of the occlusal variable (P < 0.05), no statistically significant gingival variable (P > 0.05). About fluoride release: According to the repeated measures variance analysis results, the difference between the groups, and between the time-group interaction and according to time, was found to be statistically significant (P < 0.05). CONCLUSIONS: In terms of microleakage, it was concluded that all materials could be used in clinical applications. The Equia high-viscosity glass ionomer cements (HVGIC) was determined to be the material with the highest fluoride release value.

Polymerization characteristics of colored compomers cured with different LED units.

AIM:: Incomplete polymerization of a resin material used for dental restoration affects the properties of the restoration. We evaluated the structural and mechanical properties of three different colored compomers cured with three different LED units to observe the characteristic changes occurring in different matches. METHODS:: Polytetrafluoroethylene molds (5 mm in diameter and 2 mm in thickness) were used to prepare disk-shaped sample specimens. Nine sample groups (each of five specimens) were prepared, three each of different compomer resin colors (gold, berry, and silver). Samples were cured using three different LED units (Optima, VALO, and Demi Ultra), according to the manufacturers' instructions. Microstructural properties of samples were characterized by determining the degree of curing using Fourier-transform infrared spectroscopy and by analyzing sample morphology under a scanning electron microscope. The Vickers hardness, compressive strength, and elastic modulus of the samples were measured to investigate their mechanical properties. RESULTS:: The degrees of curing decreased in the order of silver > berry > gold for all curing units. Conversely, gold compomers exhibited poorer mechanical values than the berry and silver counterparts. The Optima 10 unit yielded slightly higher degrees of curing than the other devices, followed by Demi Ultra and VALO light-curing units, respectively. CONCLUSION:: The resin color affected the structural and mechanical properties of the compomers, possibly as a result of the complex interactions and relationships between the irradiation light and resin material, such as light absorbance and reflectance; thus, depending on the color as well as the curing protocol.

Changes in the physical properties and color stability of aesthetic restorative materials caused by various beverages.

This study investigates the effects of various beverages on the wettability, microhardness, and color stability of aesthetic dental restorative materials. A contact angle analyzer, Vickers hardness tester, and spectrophotometer were used to characterize the properties of the materials and a total of 225 specimens were prepared: 75 each for a resin composite, compomer, and giomer. Ingestion of energy drinks and cola caused the greatest deterioration in wettability and microhardness, and coffee caused the most significant color change. In addition, the change in the resin composite was lower than that of the other restorative materials. The extent of change in the restorative materials increased with duration and frequency of contact with the beverages, so a reduction in the frequency of ingestion of these beverages is recommended.

The Evaluation of Color and Surface Roughness Changes in Resin based Restorative Materials with Different Contents After Waiting in Various Liquids: An SEM and AFM study.

The aim of the study was to evaluate of surface roughness and color changes of the resin-based five restorative dental materials after aging in liquids at different pH values. Totally 250 specimens were prepared, including 50 specimens for the each material group from five different restorative materials (G1[Filtek Z550], G2[Beautifil II], G3[Vertise Flow], G4[Dyract XP], G5[GCFujiIILC]), using the 10-mm diameter and 2-mm thickness molds. A total of 50 specimens in the each group, were divided into five subgroups (n = 10) to be immerse into five liquids at different pH. After initial color and roughness measurements, samples were stored in the same liquids for 7 and 14 days and all of the measurements were repeated on the 7th and 14th days. scanning electron microscopy and atomic force microscopy analyses were performed in the all groups. When the color change(ΔE) results are examined statistically; most of the ΔE is in Fuji II LC; and at least in Filtek Z550, it was determined that cola and gastric acid had the greatest effect on ΔE averages and showed significant differences (p < .05). When the average roughness values(Ra) are analyzed statistically, the highest values were found in Fuji II LC and the lowest values were found in Filtek Z550 (p < .05). The liquids which had the highest roughness average (ΔRa) were statistically significant and gastric acid and orange juice were the most effective ones (p < .05). Asidic beverages significantly increased the surface roughness and discoloration of dental restorative materials. RESEARCH HIGHLIGHTS: The results of this research showed that dental restorative materials, which are resin-based, affected both the color and surface roughness after waiting in the low pH value beverages. These results are supported with the scanning electron microscopy and atomic force microscopy images in our research. Clinically, this situation will create esthetic and functional problems in the dental filling restorations. For this reason, the results of this study seem to be important and we think that this article could be contribute to the literature.

Microtensile Bond Strength of Polyacid-modified Composite Resin to Irradiated Primary Molars.

AIM: This study evaluated the influence of various doses of radiotherapy on the microtensile bond strength (pTBS) of compomer resin to dentin and enamel in primary molars. MATERIALS AND METHODS: Thirty-five intact primary molars were collected and divided into seven groups. Teeth were irradiated with doses from 10 to 60 Gy, except for the control group. Compomer restorations were performed, and enamel-compomer resin beams and dentin-compomer resin beams were tested at a crosshead speed of 1 mm/min. RESULTS: No statistically significant difference was found between the irradiated tooth enamel and the control group (F = 1.1468; p = 0.194). However, statistically significant differences were evident among the dentin groups (F = 11.050; p < 0.001). CONCLUSION: Radiation may not cause a significant difference in the pTBS of compomer resin to primary tooth enamel, but appears to dose dependently decrease its bond strength to primary tooth dentin. CLINICAL SIGNIFICANCE: Radiotherapy may affect the success rate of compomer fillings in primary teeth, especially in deeper cavities with exposed dentin.

Characterization of fluoride releasing restorative dental materials.

This study aimed to evaluate and compare certain mechanical properties, Vickers-hardness, water sorption, fluoride-release, shrinkage-stress and wear of five commercial fluoride-releasing restorative materials (Dyract, CompGlass, BEAUTIFIL II, ACTIVA-Restorative, and GC Fuji II LC), in relation to their microstructural characteristics. Mechanical properties were determined for each material following ISO standards. A wear test was conducted with 15,000 chewing cycles using a dual-axis chewing simulator. Daily fluoride-release was measured during the first 10 days by using a fluoride ion selective electrode. Scanning electron microscopy (SEM) was used to evaluate the microstructure of each material. Results were statistically analysed using ANOVA followed by post hoc Tukey's test. ACTIVA-Restorative exhibited the highest fracture toughness (1.1 MPa m1/2) among the materials tested. BEAUTIFIL II presented the highest flexural strength (145 MPa) which was not significantly different (p>0.05) from CompGlass and Dyract. Highest fluoride-release measurement was located for GC Fuji II LC among other tested materials.

The effect of restorative materials on cytokines in gingival crevicular fluid.

OBJECTIVE: Composition of the restorative materials may cause inflammatory responses by monocyte activation and changes in the levels of cytokine released from different cells. Interleukin-6 (IL-6), interleukin-8 (IL-8) and Tumor necrosis factor alpha (TNF-α) are important cytokine for evaluating of the inflammatory process. The aim of this study was to evaluate the different restorative materials used in class V cavities effect on gingival crevicular fluid inflammatory cytokine levels. DESIGN: 60 individuals having Class V carious cavities participated in the study. Cavities were restored with FiltekZ250, DyractXP, Fuji IX, Cavex avalloy restorative materials. Changes in clinical and biochemical parameters were evaluated before restorations, seven and 21days after restorations. Contralateral tooth intact enamel surface was determined as control side. Periotron8000 device was used for detection of GCF volume. Cytokine level of GCF was evaluated by Human ELISA kits. Data were analyzed using Mann-Whitney U test and Wilcoxon signed ranks test. The correlations between clinical parameters and biochemical parameters were examined by Spearman's rank correlation analysis. RESULTS: After restorative treatments PI and GI scores were decreased compared with baseline evaluations. There was a significant difference in GCF levels between experimental and control sites in all groups. GCF IL-6 levels in all groups except Filtek Z250, GCF IL-8 levels in all groups except Fuji IX, GCF TNF-α level in only Fuji IX showed significant differences between experimental and control sites. CONCLUSIONS: The obtained data supported that all of the tested materials caused changes in GCF cytokine levels.

Long-term in-vivo effect of various restorative materials on enamel and dentin of primary molars.

OBJECTIVE: To explore the long-term in-vivo effect of different dental restorative materials on the surrounding enamel and dentin, in primary molars. METHOD AND MATERIALS: Sixteen naturally exfoliated primary molars restored with amalgam, compomer, and glass-ionomer cement were collected after 2 to 5 years of function in the mouth. Four intact molars served as control. The teeth were sliced buccolingually and the ion content in the restorative material, the enamel, and the dentin surrounding the restoration was determined using a scanning electron microscopy-energy dispersive x-ray spectroscopy (SEM-EDS) program. RESULTS: Amalgam released copper to the enamel and dentin causing a bluish discoloration. No traces of mercury or other ions were detected in the enamel or dentin. The enamel and dentin surrounding the restoration showed reduced inorganic components and increased organic components. The enamel and dentin surrounding the compomer restoration showed similar to amalgam reduction in inorganic components and increased organic components. Traces of fluoride, aluminum, and silicon were found. The enamel and dentin of teeth restored with glass-ionomer cement showed the least reduction in inorganic components, with higher fluoride content and traces of aluminum, silicon, and strontium. CONCLUSION: This long-term in-vivo study showed release of copper ions from amalgam material to the enamel and dentin, but no traces of mercury. Amalgam and compomers showed no remineralization effect on the dentin surrounding the restoration. Glass-ionomer restorations showed remineralization effect on the tooth components and migration of inorganic ions from the enamel and dentin to the material.

A comprehensive evaluation of application of light-cured colored compomer for deciduous teeth.

Twinky Star colored compomer produced by VOCO GmbH is a new type of filling material designed with seven different colors. Previous studies have shown that using the colored filling material can induce children’s curiosity and increase the acceptance for dental treatment. However, few studies have been conducted to evaluate it. Hence, the present study was designed to assess the mechanical and adhesive properties of this new compomer, examine its biological safety, and evaluate the effects of its clinical application on children’s adherence to dental treatment and the subsequent therapeutic outcomes. We found that Twinky Star compomer has a high compressive strength, good biaxial flexural strength, low wear rate, and good adhesive properties, and had little in vitro cytotoxic effects and did not cause apparent hemolysis in vivo. Finally, application of the compomer helped to improve children’s acceptance of treatment without affecting the subsequent therapeutic outcomes in the follow-up examinations. To summarize, the findings suggest that Twinky Star compomer meets the performance requirements for dental fillings, and can be recommended for future clinical application.

Thermal conductivity of different colored compomers.

BACKGROUND: Compomers are mostly used in primary dentition. The thermal conductivity properties of traditional or colored compomers have not been investigated in detail so far. The aim of this in vitro study was to assess and compare the thermal conductivities of traditional and colored compomers. METHOD: Two sets of compomers - namely, Twinky Star (available in berry, lemon, green, silver, blue, pink, gold and orange shades) and Dyract Extra (available in B1, A3 and A2 shades) - were included in this study. All of the traditional and colored compomers were applied to standard molds and polymerized according to the manufacturers' instructions. Three samples were prepared from each compomer. Measurements were conducted using a heat conduction test setup, and the coefficient of heat conductivity was calculated for each material. The heat conductivity coefficients were statistically analyzed using Kruskal-Wallis and Duncan tests. Uncertainty analysis was also performed on the calculated coefficients of heat conductivity. RESULTS: Statistically significant differences were found (p<0.05) between the thermal conductivity properties of the traditional and colored compomers examined. Among all of the tested compomers, the silver shade compomer exhibited the highest coefficient of heat conductivity (p<0.05), while the berry shade exhibited the lowest coefficient (p<0.05). Uncertainty analyses revealed that 6 out of 11 samples showed significant differences. CONCLUSIONS: The silver shade compomer should be avoided in deep cavities. The material properties could be improved for colored compomers.

Color stability of nanohybrid resin-based composites, ormocers and compomers.

OBJECTIVE: The aim of this study is to evaluate the color stability of two nanohybrid resin-based composites, two organic modified ceramic resin composites (ormocers) and a compomer, following their immersion during 4 weeks in four usual drinks. MATERIAL AND METHODS: Forty discs of each of the following materials were prepared: GrandioSO (GR), Esthet X (EX), Dyract EXTRA (DY), Ceram X duo (CX), and Admira Fusion (AD). The discs were polished and stored in distilled water during 24 h at 37 °C. Color according to the CIEL*a*b* scale was recoded. Ten randomly selected samples of each material were immersed in red wine (RW), coffee (CF), cola (CK), and distilled water (DW). The color was recorded after 1, 7, 21 and 28 days of immersion. The ΔE values between the baseline color and each of the study timepoints were calculated. The data were analyzed based on the Kruskal-Wallis test, Wilcoxon test, and Mann-Whitney U test. RESULTS: After 1 day of immersion, all the materials showed ΔE > 3.3, except EX, CF, and CX in CK. RD was the most staining beverage (ΔE 15.36 to 31.09). EX and CX were significantly less stained than the rest of the materials (p < 0.05). CONCLUSIONS: All the staining solutions produced darkening beyond clinically acceptable limits. EX and CX were the materials who experimented less staining, followed by GD. AD and DY were the materials more stained. RW was the drink that produced more staining, followed by CF and CK. CLINICAL RELEVANCE: After 24 h of immersion in all the solutions, equivalent to 1 month of exposure in the mouth, the evaluated materials showed clinically unacceptable ΔE values.

Clinical performance of aesthetic restorative materials in primary teeth according to the FDI criteria.

AIM: The purpose of this study is to evaluate the clinical performance of three different restorative materials in primary teeth according to the FDI criteria. MATERIALS AND METHODS: Resin-modified glass ionomer cement, compomer and composite resin restorations (n=93) were made in 31 patients. The restorations were clinically evaluated at baseline, 6th, 12th and 18th month with the FDI criteria. RESULTS: The cumulative survival rate after 18 months was found to be 90.3% for resin modified glass ionomer cement restorations, 100% for compomer restorations and 80.6% for composite resin restorations. Statistically significant increase in surface roughness, colour mismatch, anatomic form loss and marginal deterioration were detected in resin- modified glass ionomer group (p<0.05). The most frequent reason for restoration failure in composite resin group was restoration fractures. CONCLUSIONS: The resin-modified glass ionomer restorations necessitates close follow-up because of the risk of increase in surface roughness, changes in colour and loss in anatomic form and marginal adaptation. The clinical performance of compomer restorations is superior to resin-modified glass ionomer and composite resin restorations in primary teeth.