The influence of tympanic-membrane orientation on acoustic ear-canal quantities: A finite-element analysis.

Assuming plane waves, ear-canal acoustic quantities, collectively known as wideband acoustic immittance (WAI), are frequently used in research and in the clinic to assess the conductive status of the middle ear. Secondary applications include compensating for the ear-canal acoustics when delivering stimuli to the ear and measuring otoacoustic emissions. However, the ear canal is inherently non-uniform and terminated at an oblique angle by the conical-shaped tympanic membrane (TM), thus potentially confounding the ability of WAI quantities in characterizing the middle-ear status. This paper studies the isolated possible confounding effects of TM orientation and shape on characterizing the middle ear using WAI in human ears. That is, the non-uniform geometry of the ear canal is not considered except for that resulting from the TM orientation and shape. This is achieved using finite-element models of uniform ear canals terminated by both lumped-element and finite-element middle-ear models. In addition, the effects on stimulation and reverse-transmission quantities are investigated, including the physical significance of quantities seeking to approximate the sound pressure at the TM. The results show a relatively small effect of the TM orientation on WAI quantities, except for a distinct delay above 10 kHz, further affecting some stimulation and reverse-transmission quantities.

Measurements of bone-conducted sound in the chinchilla external ear.

We measure bone-conduction (BC) induced skull velocity, sound pressure at the tympanic membrane (TM) and inner-ear compound-action potentials (CAP) before and after manipulating the ear canal, ossicles, and the jaw to investigate the generation of BC induced ear-canal sound pressures and their contribution to inner-ear BC response in the ears of chinchillas. These measurements suggest that in chinchilla: i.) Vibrations of the bony ear canal walls contribute significantly to BC-induced ear canal sound pressures, as occluding the ear canal at the bone-cartilaginous border causes a 10 dB increase in sound pressure at the TM (PTM) at frequencies below 2 kHz. ii.) The contributions to PTM of ossicular and TM motions when driven in reverse by BC-induced inner-ear sound pressures are small. iii.) The contribution of relative motions of the jaw and ear canal to PTM is small. iv.) Comparison of the effect of canal occlusion on PTM and CAP thresholds point out that BC-induced ear canal sound pressures contribute significantly to bone-conduction stimulation of the inner ear when the ear canal is occluded.

Distortion-product otoacoustic emissions measured using synchronized swept-sines.

Swept-sines provide a tool for fast and high-resolution measurement of evoked otoacoustic emissions. During the measurement, a response to swept-sine(s) is recorded by a probe placed in the ear canal. Otoacoustic emissions can then be extracted by various techniques, e.g., Fourier analysis, the heterodyne method, and the least-square-fitting (LSF) technique. This paper employs a technique originally proposed with exponential swept-sines, which allows for direct emission extraction from the measured intermodulation impulse response. It is shown here that the technique can be used to extract distortion-product otoacoustic emissions (DPOAEs) evoked with two simultaneous swept-sines. For proper extraction of the DPOAE phase, the technique employs previously proposed adjusted formulas for exponential swept-sines generating so-called synchronized swept-sines (SSSs). Here, the SSS technique is verified using responses derived from a numerical solution of a cochlear model and responses measured in human subjects. Although computationally much less demanding, the technique yields comparable results to those obtained by the LSF technique, which has been shown in the literature to be the most noise-robust among the emission extraction methods.

3D Finite Element Model of Human Ear with 3-Chamber Spiral Cochlea for Blast Wave Transmission from the Ear Canal to Cochlea.

Blast-induced auditory trauma is a common injury in military service members and veterans that leads to hearing loss. While the inner ear response to blast exposure is difficult to characterize experimentally, computational models have advanced to predict blast wave transmission from the ear canal to the cochlea; however, published models have either straight or spiral cochlea with fluid-filled two chambers. In this paper, we report the recently developed 3D finite element (FE) model of the human ear mimicking the anatomical structure of the 3-chambered cochlea. The model consists of the ear canal, middle ear, and two and a half turns of the cochlea with three chambers separated by the Reissner's membrane (RM) and the basilar membrane (BM). The blast overpressure measured from human temporal bone experiments was applied at the ear canal entrance and the Fluent/Mechanical coupled fluid-structure interaction analysis was conducted in ANSYS software. The FE model-derived results include the pressure in the canal near the tympanic membrane (TM) and the intracochlear pressure at scala vestibuli, the TM displacement, and the stapes footplate (SFP) displacement, which were compared with experimentally measured data in human temporal bones. The validated model was used to predict the biomechanical response of the ear to blast overpressure: distributions of the maximum strain and stress within the TM, the BM displacement variation from the base to apex, and the energy flux or total energy entering the cochlea. The comparison of intracochlear pressure and BM displacement with those from the FE model of 2-chambered cochlea indicated that the 3-chamber cochlea model with the RM and scala media chamber improved our understanding of cochlea mechanics. This most comprehensive FE model of the human ear has shown its capability to predict the middle ear and cochlea responses to blast overpressure which will advance our understanding of auditory blast injury.

The Effect of Stimulation Position and Ear Canal Occlusion on Perception of Bone Conducted Sound.

The position of a bone conduction (BC) transducer influences the perception of BC sound, but the relation between the stimulation position and BC sound perception is not entirely clear. In the current study, eleven participants with normal hearing were evaluated for their hearing thresholds and speech intelligibility for three stimulation positions (temple, mastoid, and condyle) and four types of ear canal occlusion produced by headphones. In addition, the sound quality for three types of music was rated with stimulation at the three positions. Stimulation at the condyle gave the best performance while the temple showed the worst performance for hearing thresholds, speech intelligibility, and sound quality. The in-ear headphones gave the highest occlusion effect while fully open headphones gave the least occlusion effect. BC stimulated speech intelligibility improved with greater occlusion, especially for the temple stimulation position. The results suggest that BC stimulation at the condyle is generally superior to the other positions tested in terms of sensitivity, clarity, and intelligibility, and that occlusion with ordinary headphones improves the BC signal.

Three-Dimensional Finite Element Modeling of Blast Wave Transmission From the External Ear to a Spiral Cochlea.

Blast-induced injuries affect the health of veterans, in which the auditory system is often damaged, and blast-induced auditory damage to the cochlea is difficult to quantify. A recent study modeled blast overpressure (BOP) transmission throughout the ear utilizing a straight, two-chambered cochlea, but the spiral cochlea's response to blast exposure has yet to be investigated. In this study, we utilized a human ear finite element (FE) model with a spiraled, two-chambered cochlea to simulate the response of the anatomical structural cochlea to BOP exposure. The FE model included an ear canal, middle ear, and two and half turns of two-chambered cochlea and simulated a BOP from the ear canal entrance to the spiral cochlea in a transient analysis utilizing fluid-structure interfaces. The model's middle ear was validated with experimental pressure measurements from the outer and middle ear of human temporal bones. The results showed high stapes footplate (SFP) displacements up to 28.5 µm resulting in high intracochlear pressures and basilar membrane (BM) displacements up to 43.2 µm from a BOP input of 30.7 kPa. The cochlea's spiral shape caused asymmetric pressure distributions as high as 4 kPa across the cochlea's width and higher BM transverse motion than that observed in a similar straight cochlea model. The developed spiral cochlea model provides an advancement from the straight cochlea model to increase the understanding of cochlear mechanics during blast and progresses toward a model able to predict potential hearing loss after blast.

The outer ear pathway during hearing by bone conduction.

There have been conflicting reports in the literature about the importance of the induced ear canal sound pressure for the perception of bone-conducted (BC) sound. Here we investigated this by comparing the ear canal sound pressure at threshold for air-conducted (AC) and BC stimulation. Twenty-one adults with subjectively normal hearing function participated. They were tested for their hearing thresholds in the frequency range 250 Hz to 12.5 kHz with AC and BC stimulation and the ear canal sound pressure within 5 mm of the eardrum was obtained with probe tube microphones. Contralateral masking used with BC stimulation shifted the hearing threshold by 5 to 10 dB due to central masking effects. When the ear canal sound pressures at threshold were investigated, the results indicate that the ear canal component for hearing BC sound is around 10 dB below other contributors at frequencies below 2 kHz and similar to other important contributors at frequencies between 2 and 4 kHz. At frequencies above 4 kHz, the contribution from the ear canal sound pressure on BC hearing declines and was around 40 dB below other contributors at 12.5 kHz. The contribution of the ear canal sound pressure in the mid-frequency region is facilitated by the ear canal resonance occurring in this frequency area. The results were similar irrespective of stimulation position. The study also revealed problems estimating the force out of BC transducers caused by a shift in resonance frequency when the artificial mastoid impedance deviates from the impedance of human mastoids. The current study indicates that model predictions have underestimated the contribution from the ear canal sound pressure on BC hearing by around 10 dB.

A narrow ear canal reduces sound velocity to create additional acoustic inputs in a microscale insect ear.

Located in the forelegs, katydid ears are unique among arthropods in having outer, middle, and inner components, analogous to the mammalian ear. Unlike mammals, sound is received externally via two tympanic membranes in each ear and internally via a narrow ear canal (EC) derived from the respiratory tracheal system. Inside the EC, sound travels slower than in free air, causing temporal and pressure differences between external and internal inputs. The delay was suspected to arise as a consequence of the narrowing EC geometry. If true, a reduction in sound velocity should persist independently of the gas composition in the EC (e.g., air, [Formula: see text]). Integrating laser Doppler vibrometry, microcomputed tomography, and numerical analysis on precise three-dimensional geometries of each experimental animal EC, we demonstrate that the narrowing radius of the EC is the main factor reducing sound velocity. Both experimental and numerical data also show that sound velocity is reduced further when excess [Formula: see text] fills the EC. Likewise, the EC bifurcates at the tympanal level (one branch for each tympanic membrane), creating two additional narrow internal sound paths and imposing different sound velocities for each tympanic membrane. Therefore, external and internal inputs total to four sound paths for each ear (only one for the human ear). Research paths and implication of findings in avian directional hearing are discussed.

A novel cooling method using carbon dioxide-rich water after passive heating.

In the event of a marked rise in body temperature, it is often necessary to reduce the temperature quickly. One method to rapidly drop body temperature is cold water immersion. Because carbon dioxide (CO2)-rich water causes cutaneous vasodilation, it may be that CO2-rich water reduces body temperature faster than fresh water. To test that idea, I compared the effects of CO2-rich and tap water immersion on auditory canal temperature (Tac) after passive heating. Nine healthy male subjects participated in the study. Subjects were first immersed for 15 min in a tap water bath at 40 °C to raise body temperature. They then moved to a tap water or CO2-rich water bath at 30 °C to reduce body temperature. Immersion in 40 °C tap water caused Tac to rise 0.64 ± 0.11 °C in the tap water session and 0.71 ± 0.25 °C in the CO2-rich water session (P > 0.05). During the 30 °C water immersion, Tac declined and was significantly lower in CO2-rich water than in tap water. Cooling rates were 0.06 ± 0.04 °C/min in tap water and 0.11 ± 0.05 °C/min in CO2-rich water (P < 0.05). In addition, both thermal sensation (3.2 ± 1.0 vs. 2.1 ± 0.9; P < 0.01) and thermal comfort (1.2 ± 0.4 vs. 2.1 ± 0.8; P < 0.01) were significantly better in CO2-rich water than tap water. These results suggest that CO2-rich water immersion reduces Tac 1.7 times faster than tap water immersion, and that CO2-rich water immersion cools the body more comfortably than tap water immersion.

Infrasonic hearing in birds: a review of audiometry and hypothesized structure-function relationships.

The perception of airborne infrasound (sounds below 20 Hz, inaudible to humans except at very high levels) has been documented in a handful of mammals and birds. While animals that produce vocalizations with infrasonic components (e.g. elephants) present conspicuous examples of potential use of infrasound in the context of communication, the extent to which airborne infrasound perception exists among terrestrial animals is unclear. Given that most infrasound in the environment arises from geophysical sources, many of which could be ecologically relevant, communication might not be the only use of infrasound by animals. Therefore, infrasound perception could be more common than currently realized. At least three bird species, each of which do not communicate using infrasound, are capable of detecting infrasound, but the associated auditory mechanisms are not well understood. Here we combine an evaluation of hearing measurements with anatomical observations to propose and evaluate hypotheses supporting avian infrasound detection. Environmental infrasound is mixed with non-acoustic pressure fluctuations that also occur at infrasonic frequencies. The ear can detect such non-acoustic pressure perturbations and therefore, distinguishing responses to infrasound from responses to non-acoustic perturbations presents a great challenge. Our review shows that infrasound could stimulate the ear through the middle ear (tympanic) route and by extratympanic routes bypassing the middle ear. While vibration velocities of the middle ear decline towards infrasonic frequencies, whole-body vibrations - which are normally much lower amplitude than that those of the middle ear in the 'audible' range (i.e. >20 Hz) - do not exhibit a similar decline and therefore may reach vibration magnitudes comparable to the middle ear at infrasonic frequencies. Low stiffness in the middle and inner ear is expected to aid infrasound transmission. In the middle ear, this could be achieved by large air cavities in the skull connected to the middle ear and low stiffness of middle ear structures; in the inner ear, the stiffness of round windows and cochlear partitions are key factors. Within the inner ear, the sizes of the helicotrema and cochlear aqueduct are expected to play important roles in shunting low-frequency vibrations away from low-frequency hair-cell sensors in the cochlea. The basilar papilla, the auditory organ in birds, responds to infrasound in some species, and in pigeons, infrasonic-sensitive neurons were traced back to the apical, abneural end of the basilar papilla. Vestibular organs and the paratympanic organ, a hair cell organ outside of the inner ear, are additional untested candidates for infrasound detection in birds. In summary, this review brings together evidence to create a hypothetical framework for infrasonic hearing mechanisms in birds and other animals.

Morphological Evidence for the Sensitivity of the Ear Canal of Odontocetes as shown by Immunohistochemistry and Transmission Electron Microscopy.

The function of the external ear canal in cetaceans is still under debate and its morphology is largely unknown. Immunohistochemical (IHC) analyses using antibodies specific for nervous tissue (anti-S100, anti-NSE, anti-NF, and anti-PGP 9.5), together with transmission electron microscopy (TEM) and various histological techniques, were carried out to investigate the peripheral nervous system of the ear canals of several species of toothed whales and terrestrial Cetartiodactyla. This study highlights the innervation of the ear canal with the presence of lamellar corpuscles over its entire course, and their absence in all studied terrestrial mammals. Each corpuscle consisted of a central axon, surrounded by lamellae of Schwann receptor cells, surrounded by a thin cellular layer, as shown by IHC and TEM. These findings indicate that the corpuscles are mechanoreceptors that resemble the inner core of Pacinian corpuscles without capsule or outer core, and were labelled as simple lamellar corpuscles. They form part of a sensory system that may represent a unique phylogenetic feature of cetaceans, and an evolutionary adaptation to life in the marine environment. Although the exact function of the ear canal is not fully clear, we provide essential knowledge and a preliminary hypothetical deviation on its function as a unique sensory organ.

Causality-constrained measurements of aural acoustic reflectance and reflection functions.

Causality-constrained procedures are described to measure acoustic pressure reflectance and reflection function (RF) in the ear canal or unknown waveguide, in which reflectance is the Fourier transform of the RF. Reflectance calibration is reformulated to generate causal outputs, with results described for a calibration based on a reflectance waveguide equation to calculate incident pressure and source reflectance in the frequency domain or source RF in the time domain. The viscothermal model RF of each tube is band-limited to the stimulus bandwidth. Results are described in which incident pressure is either known from long-tube measurements or calculated as a calibration output. Calibrations based on constrained nonlinear optimizations are simpler and more accurate when incident pressure is known. Outputs measured by causality-constrained procedures differ at higher frequencies from those using standard procedures with non-causal outputs. Evanescent-mode effects formulated in the time domain and incorporated into frequency-domain calibrations are negligible for long-tube calibrations. Causal reflectance and RFs are evaluated in an adult ear canal and time- and frequency-domain results are contrasted using forward and inverse Fourier transforms. These results contribute to the long-term goals of improving applications to calibrate sound stimuli in the ear canal at high frequencies and diagnose conductive hearing impairments.

Establishing critical differences in ear-canal stimulus amplitude for detecting middle ear muscle reflex activation during olivocochlear efferent measurements.

Objective: Assessments of the medial olivocochlear reflex (MOCR) may have clinical utility. The MOCR is measured using contralateral inhibition of otoacoustic emissions but concurrent activation of the middle ear muscle reflex (MEMR) confounds test interpretation. MEMR activation can be detected using the change in ear-canal stimulus amplitude without versus with an MOCR elicitor. This study provides a description of how critical differences in ear-canal stimulus amplitude can be established.Design: Clicks were presented in right ears without and with a contralateral MOCR elicitor. Ear-canal stimulus amplitudes were measured. Two measurements without an elicitor were used to develop critical differences. MEMR activation was considered present if the difference in ear-canal stimulus amplitude without versus with an elicitor exceeded the critical difference.Study sample: Forty-six normal-hearing adults (mean age = 23.4 years, 35 females) participated, with data from 44 participants included in the final analysis.Results: Two participants exceeded the 95% critical difference. The 80, 90 and 99% critical differences are also reported for reference.Conclusions: Results suggest that the contralateral elicitor can evoke the MEMR in a small number of participants. The methods described in this paper can be used for developing equipment- and clinic-specific critical differences for detecting MEMR activation.

A comparison of ear-canal-reflectance measurement methods in an ear simulator.

Ear-canal reflectance has been researched extensively for diagnosing conductive hearing disorders and compensating for the ear-canal acoustics in non-invasive measurements of the auditory system. Little emphasis, however, has been placed on assessing measurement accuracy and variability. In this paper, a number of ear-canal-reflectance measurement methods reported in the literature are utilized and compared. Measurement variation seems to arise chiefly from three factors: the residual ear-canal length, the ear-probe insertion angle, and the measurement frequency bandwidth. Calculation of the ear-canal reflectance from the measured ear-canal impedance requires estimating the ear-canal characteristic impedance in situ. The variability in ear-canal estimated characteristic impedance and reflectance due to these principal factors is assessed in an idealized controlled setup using a uniform occluded-ear simulator. In addition, the influence of this measurement variability on reflectance-based methods for calibrating stimulus levels is evaluated and, by operating the condenser microphone of the occluded-ear simulator as an electro-static speaker, the variability in estimating the emitted pressure from the ear is determined. The various measurement methods differ widely in their robustness to variations in the three principal factors influencing the accuracy and variability of ear-canal reflectance.

On the calculation of reflectance in non-uniform ear canals.

Ear-canal reflectance is useful for quantifying the conductive status of the middle ear because it can be measured non-invasively at a distance from the tympanic membrane. Deriving the ear-canal reflectance requires decomposing the total acoustic pressure into its forward- and reverse-propagating components. This decomposition is conveniently achieved using formulas that involve the input and characteristic impedances of the ear canal. The characteristic impedance is defined as the ratio of sound pressure to volume flow of a propagating wave and, for uniform waveguides, the plane-wave characteristic impedance is a real-valued constant. However, in non-uniform waveguides, the characteristic impedances are complex-valued quantities, depend on the direction of propagation, and more accurately characterize a propagating wave in a non-uniform ear canal. In this paper, relevant properties of the plane-wave and spherical-wave characteristic impedances are reviewed. In addition, the utility of the plane-wave and spherical-wave reflectances in representing the reflection occurring due to the middle ear, calibrating stimulus levels, and characterizing the emitted pressure in simulated non-uniform ear canals is investigated and compared.

Simultaneous Measurement of Ear Canal Movement, Electromyography of the Masseter Muscle and Occlusal Force for Earphone-Type Occlusal Force Estimation Device Development.

We intend to develop earphone-type wearable devices to measure occlusal force by measuring ear canal movement using an ear sensor that we developed. The proposed device can measure occlusal force during eating. In this work, we simultaneously measured the ear canal movement (ear sensor value), the surface electromyography (EMG) of the masseter muscle and the occlusal force six times from five subjects as a basic study toward occlusal force meter development. Using the results, we investigated the correlation coefficient between the ear sensor value and the occlusal force, and the partial correlation coefficient between ear sensor values. Additionally, we investigated the average of the partial correlation coefficient and the absolute value of the average for each subject. The absolute value results indicated strong correlation, with correlation coefficients exceeding 0.9514 for all subjects. The subjects showed a lowest partial correlation coefficient of 0.6161 and a highest value of 0.8286. This was also indicative of correlation. We then estimated the occlusal force via a single regression analysis for each subject. Evaluation of the proposed method via the cross-validation method indicated that the root-mean-square error when comparing actual values with estimates for the five subjects ranged from 0.0338 to 0.0969.

Compensating for oblique ear-probe insertions in ear-canal reflectance measurements.

Measurements of the ear-canal reflectance using an ear probe require estimating the characteristic impedance of the ear canal in situ. However, an oblique insertion of the ear probe into a uniform waveguide prevents accurately estimating its characteristic impedance using existing time-domain methods. This is caused by the non-uniformity immediately in front of the ear probe when inserted at an oblique angle, resembling a short horn loading, and introduces errors into the ear-canal reflectance. This paper gives an overview of the influence of oblique ear-probe insertions and shows how they can be detected and quantified by estimating the characteristic impedance using multiple truncation frequencies, i.e., limiting the utilized frequency range. Additionally, a method is proposed to compensate for the effects on reflectance of an oblique ear-probe insertion into a uniform waveguide. The incident impedance of the horn loading is estimated, i.e., were the uniform waveguide anechoic, which replaces the characteristic impedance when calculating reflectance. The method can compensate for an oblique ear-probe insertion into a uniform occluded-ear simulator and decrease the dependency of reflectance on insertion depth in an ear canal. However, more research is required to further assess the method in ear canals.

Sound pressure distribution within human ear canals: II. Reverse mechanical stimulation.

This work is part of a study of the interactions of ear canal (EC) sound with tympanic membrane (TM) surface displacements. In human temporal bones, the ossicles were stimulated mechanically "in reverse" to mimic otoacoustic emissions (OAEs), and the sound field within the ear canal was sampled with 0.5-2 mm spacing near the TM surface and at more distal locations within the EC, including along the longitudinal EC axis. Sound fields were measured with the EC open or occluded. The reverse-driven sound field near the TM had larger and more irregular spatial variations below 10 kHz than with forward sound stimulation, consistent with a significant contribution of nonuniform sound modes. These variations generally did not propagate more than ∼4 mm laterally from the TM. Longitudinal sound field variations with the EC open or blocked were consistent with standing-wave patterns in tubes with open or closed ends. Relative contributions of the nonuniform components to the total sound pressure near the TM were largest at EC natural frequencies where the longitudinal component was small. Transverse variations in EC sound pressure can be reduced by reducing longitudinal EC sound pressure variations, e.g., via reducing reflections from occluding earplugs.

Contralateral Occlusion Test (COT): the effect of external ear canal occlusion with aging.

PURPOSE: This study aimed to evaluate the effects of complete external ear canal occlusion on hearing thresholds with aging. The goal was to decide which tuning fork is more appropriate to use for the contralateral occlusion test (COT), in individuals of different ages. METHODS: Forty-two normal hearing subjects between 21 and 67 years were divided into three age groups (20-30 years, 40-50 years, and 60-70 years). Participants underwent sound field audiometry tests with warble tones, with and without ear canal occlusion. Each ear was tested with the standard frequencies (250, 500, 1000, and 2000 Hz). The contralateral ear was suppressed by masking. RESULTS: Hearing thresholds showed an increase as the frequency increased from 20.85 dB (250 Hz, 20-30 years group) to 48 dB (2000 Hz, 60-70 years group). The threshold differences between occlusion and no occlusion conditions were statistically significant and increased ranging from 11.1 dB (250 Hz, 20-30 years group) to 32 dB (2000 Hz, 20-30 years group). We found statistically significant differences for the three age groups and for all evaluations except to 500 Hz difference and average difference. The mean hearing loss produced by occlusion at 500 Hz was approximately 19 dB. We found no statistically significant differences between right and left ears and gender for all measurements. CONCLUSION: We conclude that the use of the 512 Hz tuning fork is the most suitable for COT, and its use may allow clinicians to distinguish mild from moderate unilateral conductive hearing loss.

Voltage readout from a piezoelectric intracochlear acoustic transducer implanted in a living guinea pig.

The ability to measure the voltage readout from a sensor implanted inside the living cochlea enables continuous monitoring of intracochlear acoustic pressure locally, which could improve cochlear implants. We developed a piezoelectric intracochlear acoustic transducer (PIAT) designed to sense the acoustic pressure while fully implanted inside a living guinea pig cochlea. The PIAT, fabricated using micro-electro-mechanical systems (MEMS) techniques, consisted of an array of four piezoelectric cantilevers with varying lengths to enhance sensitivity across a wide frequency bandwidth. Prior to implantation, benchtop tests were conducted to characterize the device performance in air and in water. When implanted in the cochlea of an anesthetized guinea pig, the in vivo voltage response from the PIAT was measured in response to 80-95 dB sound pressure level 1-14 kHz sinusoidal acoustic excitation at the entrance of the guinea pig's ear canal. All sensed signals were above the noise floor and unaffected by crosstalk from the cochlear microphonic or external electrical interference. These results demonstrate that external acoustic stimulus can be sensed via the piezoelectric voltage response of the implanted MEMS transducer inside the living cochlea, providing key steps towards developing intracochlear acoustic sensors to replace external or subcutaneous microphones for auditory prosthetics.