Ratiometric Electrochemistry: Improving the Robustness, Reproducibility and Reliability of Biosensors.

Electrochemical biosensors are an increasingly attractive option for the development of a novel analyte detection method, especially when integration within a point-of-use device is the overall objective. In this context, accuracy and sensitivity are not compromised when working with opaque samples as the electrical readout signal can be directly read by a device without the need for any signal transduction. However, electrochemical detection can be susceptible to substantial signal drift and increased signal error. This is most apparent when analysing complex mixtures and when using small, single-use, screen-printed electrodes. Over recent years, analytical scientists have taken inspiration from self-referencing ratiometric fluorescence methods to counteract these problems and have begun to develop ratiometric electrochemical protocols to improve sensor accuracy and reliability. This review will provide coverage of key developments in ratiometric electrochemical (bio)sensors, highlighting innovative assay design, and the experiments performed that challenge assay robustness and reliability.

A challenge in biosensors: Is it better to measure a photon or an electron for ultrasensitive detection?

Biosensor development exploiting various transduction principles is characterized by a strong competition to reach high detectability, portability and robustness. Nevertheless, a literature-based comparison is not possible, as different conditions are employed in each paper. Herein, we aim at evaluating which measurement, photons or electrons, yields better biosensor performance. Upon outlining an update in recent achievements to boost analytical performance, amperometry and chemiluminescence (CL)-based biosensors are directly compared employing the same biospecific reagents and analytical formats. Horseradish peroxidase (HRP) and hydrogen peroxide concentrations were directly measured, while glucose and mouse IgG were detected employing an enzyme paper-based biosensor and an immunosensor, respectively. Detectability was down to picomoles of hydrogen peroxide (4 pmol for CL and 210 pmol for amperometry) and zeptomoles of HRP (45 zmol for CL and 20 zmol for amperometry); IgG was detected down to 12 fM (CL) and 120 fM (amperometry), while glucose down to 17 µM (CL) and 40 µM (amperometry). Results showed that amperometric and CL biosensors offered similar detectability and analytical performance, with some peculiarities that suggest complementary application fields. As they generally provided slightly higher detectability and wider dynamic ranges, CL-based biosensors appear more suitable for point-of-care testing of clinical biomarkers, where detectability is crucial. Nevertheless, as high detectability in CL biosensors usually requires longer acquisition times, their rapidity will allocate electrochemical biosensors in real-time monitoring and wearable biosensors. The analytical challenge demonstrated that these biosensors have competitive and similar performance, and between photons and electrons the competition is still open.

A mesoporous silver-doped TiO2-SnO2 nanocomposite on g-C3N4 nanosheets and decorated with a hierarchical core-shell metal-organic framework for simultaneous voltammetric determination of ascorbic acid, dopamine and uric acid.

An electrochemical sensor is described for the simultaneous voltammetric determination of ascorbic acid (AA), dopamine (DA), and uric acid (UA). An indium-tin oxide (ITO) electrode was modified with a hierarchical core-shell metal-organic framework and Ag-doped mesoporous metal-oxide based hybrid nanocomposites on g-C3N4 nanosheets. The morphology, structural and chemical composition of the hybrid nanocomposite was characterized using different analytical methods. The modified ITO showed superior electrocatalytic performance towards the oxidation of AA, DA and UA due to the enhanced surface area, synergistic effects and well-organized porous assembly. Figures of merit, include (a) linear responses from 0.1 to 200 µM, 2.5 to 100 µM and 2.5 to 625 µM; (b) detection limits (at S/N = 3) of 0.02, 0.01 and 0.06 µM, and (c) well separated oxidation peaks near -50, 186 and 390 mV (vs. Ag/AgCl) for simultaneous sensing AA, DA and UA, respectively. The sensor was evaluated by analysing spiked serum samples and gave data with precision, with recoveries of >98%. Graphical abstractSchematic Representation of a Mesoporous Silver-doped TiO2-SnO2 Nanocomposite (h-ATS) on g-C3N4 Nanosheets and Decorated with a Hierarchical Core-Shell Metal-Organic Framework (NC@GC) Based Electrochemical Sensor for Simultaneous Voltammetric Detection of Ascorbic acid, Dopamine and Uric acid.

Challenges of simultaneous measurements of brain extracellular GABA and glutamate in vivo using enzyme-coated microelectrode arrays.

BACKGROUND: Although GABA is the major inhibitory neurotransmitter in the CNS, quantifying in vivo GABA levels has been challenging. The ability to co-monitor both GABA and the major excitatory neurotransmitter, glutamate, would be a powerful tool in both research and clinical settings. NEW METHOD: Ceramic-based microelectrode arrays (MEAs) were used to quantify gamma-aminobutyric acid (GABA) by employing a dual-enzyme reaction scheme including GABase and glutamate oxidase (GluOx). Glutamate was simultaneously quantified on adjacent recording sites coated with GluOx alone. Endogenous glutamate was subtracted from the combined GABA and glutamate signal to yield a pure GABA concentration. RESULTS: Electrode sensitivity to GABA in conventional, stirred in vitro calibrations at pH 7.4 did not match the in vivo sensitivity due to diffusional losses. Non-stirred calibrations in agarose or stirred calibrations at pH 8.6 were used to match the in vivo GABA sensitivity. In vivo data collected in the rat brain demonstrated feasibility of the GABA/glutamate MEA including uptake of locally applied GABA, KCl-evoked GABA release and modulation of endogenous GABA with vigabatrin. COMPARISON WITH EXISTING METHODS: Implantable enzyme-coated microelectrode arrays have better temporal and spatial resolution than existing off-line methods. However, interpretation of results can be complicated due to the multiple recording site and dual enzyme approach. CONCLUSIONS: The initial in vitro and in vivo studies supported that the new MEA configuration may be a viable platform for combined GABA and glutamate measures in the CNS extending the previous reports to in vivo GABA detection. The challenges of this approach are emphasized.

Electrochemical preparation of standard solutions of Pb(II) ions in ionic liquid for analysis of hydrophobic samples: The olive oil case.

In this paper we present an electrochemical approach to prepare standard solutions of metal ions in a room temperature ionic liquid (IL), which can find useful application for analysis in hydrophobic matrices. The method, developed here for the case of lead ions, is based on the galvanostatic dissolution of a lead anode dipped directly in a suitable IL, namely tri-hexyl(tetradecyl)phosphonium bis (trifluoromethylsulfonyl) imide ([P14,6,6,6]+[NTf2]-). After each oxidation step, the metal dissolution process in the IL solutions was monitored by cyclic voltammetric measurements at a glassy carbon disk electrode. The results indicated that the peak current relevant to the reduction of the electro-generated Pb(II) increased linearly while increasing the oxidation time. By varying the oxidation time from 200 to 6000s, a set of Pb(II)/[P14,6,6,6]+[NTf2]- solutions at concentrations ranging between 10 and 300µgg-1 was prepared. To validate the efficiency of the electrochemical procedure to produce metal ion standard solutions, the Pb content was quantified by developing a microwave digestion procedure specifically suitable for the IL medium, followed by ICP-QMS analysis in the digested standards. The results indicated a satisfactory agreement between concentrations found by ICP-QMS and calculated from electrochemical data, with a coulometric efficiency of Pb(II) generation in ionic liquid ≥95.6%. Finally, the applicability of the Pb(II)/IL solutions as standards for analyses in hydrophobic media was tested by determining, by ICP-QMS, the Pb content in an extra-virgin olive oil spiked with known amounts of a Pb(II)/IL standard. Satisfactory Pb recoveries, ≥96%, were measured.

Interference from Indian diet on the internal standard in a commercial method for the measurement of urinary metanephrines by high-performance liquid chromatography with electrochemical detection.

INTRODUCTION: Urinary metanephrines are widely used in the diagnosis of catecholamine secreting tumours. Over the past two years we have been using the commercial Recipe(®) ClinRep(®) Complete Kit for Metanephrines in Urine coupled with high-performance liquid chromatography and coulometric detection. It was noticed that the internal standards on the patient chromatograms were sporadically raised due to interference. METHODS: The interference had identical chromatographic and electrochemical properties to the Recipe(®) internal standard (undisclosed identity). Inspection of the patient names showed it seemingly had a higher frequency and magnitude in patients of Indian origin. The source of the interference was tracked by dietary observation and intervention to curry leaves, a common component of Indian foods. RESULTS: The interference was chromatographically and electrochemically indistinguishable from the internal standard. The mass spectrum of the pentafluoropropionate derivative of the interference matched the Recipe(®) internal standard and was identified as methoxyhydroxybenzylamine by library match. CONCLUSION: The component co-elutes exactly with internal standard and artifactually decreases the metanephrine and normetanephrine results. It is surprising that it has not been described previously. Patients being assessed for catecholamine secreting tumours should be advised to withdraw from eating Indian foods at least 24 h prior to commencement of urinary collection.

Paper-based electroanalytical devices with an integrated, stable reference electrode.

This paper describes the development of a referenced Electrochemical Paper-based Analytical Device (rEPAD) comprising a sample zone, a reference zone, and a connecting microfluidic channel that includes a central contact zone. We demonstrated that the rEPADs provide a simple system for direct and accurate voltammetric measurements that are referenced by an electrode with a constant, well-defined potential. The performance of the rEPADs is comparable to commercial electrochemical cells, and the layout can be easily integrated into systems that permit multiplexed analysis and pipette-free sampling. The cost of this portable device is sufficiently low that it could be for single-use, disposable applications, and its method of fabrication is compatible with that used for other paper-based systems.

Determination of coenzyme Q10 tissue status via high-performance liquid chromatography with electrochemical detection in swine tissues (Sus scrofa domestica).

Swine tissues were used as surrogates for human tissues with coenzyme Q10 (CoQ10) as the primary endogenous quinoid to establish a reliable method for the analysis of total CoQ10 concentration and redox status using the reduced and oxidized forms of CoQ9 as internal standards. Specimens of frozen swine tissues were disrupted by bead milling using 2-propanol as the homogenization medium supplemented with the internal standards. After hexane extraction, CoQ10 was analyzed via high-performance liquid chromatography with electrochemical detection. The method is linear (12-60 mg fresh muscle tissue/sample), sensitive (~200 pmol CoQ10/sample), and reproducible (coefficients of variation of 6.0 and 3.2% for total CoQ10 and 2.4 and 3.2% for the redox status of within-day and day-to-day precision, respectively), with analytic recoveries for ubiquinone-10, ubihydroquinone-10, and total Q10 of 91, 104, and 94%, respectively. The concentration and redox status were stable for at least 3 months at -84°C. The total CoQ10 concentrations (pmol/mg fresh tissue) in swine tissues were as follows: lung (17.4±1.42), skeletal muscle (26.7±2.57), brain (40.7±4.02), liver (62.1±31.0), kidney (111.7±37.08), and heart muscle (149.1±36.78). Significant tissue-specific variations were also found for the redox status (% oxidation of total): swine liver (~28), lung (~36), kidney (~37), heart muscle (~57), skeletal muscle (~61), and brain (~67).

Trace level voltammetric determination of heavy metals and total mercury in tea matrices (Camellia sinensis).

An analytical procedure regarding the voltammetric determination of mercury(II), copper(II), lead(II), cadmium(II) and zinc(II) by square wave anodic stripping voltammetry (SWASV) in matrices involved in food chain is proposed. In particular, tea leaves were analyzed as real samples. The digestion of each matrix was carried out using a concentrated HCl-HNO3-H2SO4 acidic attack mixture; 0.01 mol L(-1) EDTA-Na2+ 0.15 mol L(-1) NaCl + 0.5 mol L(-1) HCl was employed as the supporting electrolyte. The voltammetric measurements were carried out using a conventional three electrode cell, employing, as working electrodes, a gold electrode (GE) and a stationary hanging mercury drop electrode (HMDE). The analytical procedure has been verified on the standard reference materials Spinach Leaves NIST-SRM 1570a, Tomato Leaves NIST-SRM 1573a and Apple Leaves NIST-SRM 1515. For all the elements, the precision as repeatability, expressed as relative standard deviation (sr) was of the order of 3-5%, while the trueness, expressed as relative error (e) was of the order of 3-7%. Once set up on the standard reference materials, the analytical procedure was applied to commercial tea leaves samples. A critical comparison with spectroscopic measurements is also discussed.

Optimization of method for zinc analysis in several bee products on renewable mercury film silver based electrode.

Zinc is an interesting target for detection as it is one of the elements necessary for the proper functioning of the human body, its excess and deficiency can cause several symptoms. Several techniques including electrochemistry have been developed but require laboratory equipment, preparative steps and mercury or complex working electrodes. We here described the development of a robust, simple and commercially available electrochemical system. Differential pulse (DP) voltammetry was used for this purpose with the cyclic renewable mercury film silver based electrode (Hg(Ag)FE) and 0.05 M KNO3 solution as a supporting electrolyte. The effect of various factors such as: preconcentration potential and time, pulse amplitude and width, step potential and supporting electrolyte composition are optimized. The limits of detection (LOD) and quantification (LOQ) were 1.62 ng/mL and 4.85 ng/mL, respectively. The repeatability of the method at a concentration level of the analyte as low as 3 ng/mL, expressed as RSD is 3.5% (n = 6). Recovery was determined using certified reference material: Virginia Tobacco Leaves (CTA-VTL-2). The recovery of zinc ranged from 96.6 to 106.5%. The proposed method was successfully applied for determination of zinc in bee products (honey, propolis and diet supplements) after digestion procedure.

Certified reference material of bioethanol for metrological traceability in electrochemical parameters analyses.

Bioethanol has become an important biofuel because it is a source of renewable energy and can help to decrease global warming. However, the quality of bioethanol needs to be guaranteed so that it can be trusted and accepted in international trade. The Brazilian Metrology Institute (Inmetro) has been developing a certified reference material (CRM) for bioethanol to ensure quality control for measurement in the bioethanol matrix. Inmetro has certified 11 quality parameters. Using these, the CRM of bioethanol will contribute to guaranteeing metrological traceability and reliable measurement results. These factors can be used to compare different bioethanols produced to comply with legislation in different countries in order to avoid technical barriers and thus increase the international trade in Brazilian bioethanol. The aim of this paper is to present the results of certification studies using three important electrochemical quality parameters in the CRM of bioethanol-total acid number, pHe and electrolytic conductivity-which are crucial in protecting the metallic parts of a vehicle from corrosion. The certified results obtained for total acid number, pHe and electrolytic conductivity parameters were (16.2±1.7)mg L(-1), 6.07±0.30, and (1.03±0.11)µS cm(-1), respectively. The uncertainties for all parameters were the expanded uncertainty obtained by multiplying the combined standard uncertainty by a coverage factor of k=2, which represents an approximately 95% confidence level.

Sensitive electrochemical immunoassay of carcinoembryonic antigen with signal dual-amplification using glucose oxidase and an artificial catalase.

A new dual-amplification strategy of electrochemical signal based on the catalytic recycling of the product was developed for the antigen-antibody interaction by glucose oxidase (GOD)- conjugated gold-silver hollow microspheres (AuAgHSs) coupled with an artificial catalase, Prussian blue nanoparticles (PB), on a graphene-based immunosensing platform. The first signal amplification introduced in this study was based on the labeled GOD on the AuAgHSs toward the catalytic oxidation of glucose. The generated H(2)O(2) was catalytically reduced by the immobilized PB on the graphene nanosheets with the second amplification. With a sandwich-type immunoassay format, carcinoembryonic antigen (CEA) was monitored as a model analyte by using the synthesized AuAgHSs as labels in pH 6.0 phosphate buffer containing 10mM glucose. Under optimal conditions, the electrochemical immunosensor exhibited a wide dynamic range of 0.005-50 ng mL(-1) with a low detection limit (LOD) of 1.0 pg mL(-1) CEA (at 3σ). Both the intra- and inter-assay coefficients of variation (CVs) were lower than 10%. The specificity and stability of the immunosensor were acceptable. In addition, the assay was evaluated for clinical serum specimens, and received a good correlation with those obtained by the referenced electrochemiluminescent (ECL).

Gold-silver-graphene hybrid nanosheets-based sensors for sensitive amperometric immunoassay of alpha-fetoprotein using nanogold-enclosed titania nanoparticles as labels.

A new sandwich-type electrochemical immunosensor with enhanced sensitivity was developed for detection of alpha-fetoprotein (AFP, as a model analyte) in biological fluids by using nanogold-enclosed titania nanoparticle (AuTi)-labeled secondary antibody on a gold-silver-graphene hybrid nanosheet (AuAgGP)-functionalized glassy carbon electrode (GCE). The presence of the AuAgGP nanosheets not only enhanced the immobilized amount of biomolecules, but also improved the electrochemical properties of the immunosensor. With the aid of AuTi nanolabels, the electrochemical signal was greatly amplified in comparison with pure nanogold or titania-based labels. Under optimal conditions, the sensitivity and dynamic range of the immunosensor were evaluated by using the labeled horseradish peroxidase on the AuTi as trace and H(2)O(2) as enzyme substrate, and exhibited a wide dynamic range of 0.001-200 ng mL(-1) with a low detection limit (LOD) of 0.5 pg mL(-1) AFP (at 3σ). Both the intra- and inter-assay coefficients of variation were less than 10%. The current of the immunosensor at 13th day was as much as 90% of the initial current. In addition, the methodology was evaluated for 8 positive serum specimens obtained from hepatocarcinoma patients and 19 negative sera, and validated with the commercially available Roche 2010 Electrochemiluminescent (ECL) Automatic Analyzer. No significant differences at the 95% confidence level were encountered between two methods.

Development of an ion sensitive field effect transistor based urea biosensor with solid state reference systems.

Ion sensitive field-effect transistor (ISFET) based urease biosensors with solid state reference systems for single-ended and two-ended differential readout electronics were investigated. The sensing membranes of the biosensors were fabricated with urease immobilized in a conducting polymer-based matrix. The responses of 12.9∼198.1 mV for the urea concentrations of 8∼240 mg/dL reveal that the activity of the enzyme was not significantly decreased. Biosensors combined with solid state reference systems were fabricated, and the evaluation results demonstrated the feasibility of miniaturization. For the differential system, the optimal transconductance match for biosensor and reference field-effect transistors (REFET) pair was determined through the modification of the membranes of the REFETs and enzyme field-effect transistors (EnFETs). The results show that the transconductance curve of polymer based REFET can match with that of the EnFET by adjusting the photoresist/Nafion™ ratio. The match of the transconductance curves for the differential pairs provides a wide dynamic operating measurement range. Accordingly, the miniaturized quasi-reference electrode (QRE)/REFET/EnFET combination with differential arrangement achieved similar urea response curves as those measured by a conventional large sized discrete sensor.

A calibration method for nanowire biosensors to suppress device-to-device variation.

Nanowire/nanotube biosensors have stimulated significant interest; however, the inevitable device-to-device variation in the biosensor performance remains a great challenge. We have developed an analytical method to calibrate nanowire biosensor responses that can suppress the device-to-device variation in sensing response significantly. The method is based on our discovery of a strong correlation between the biosensor gate dependence (dI(ds)/dV(g)) and the absolute response (absolute change in current, DeltaI). In(2)O(3) nanowire-based biosensors for streptavidin detection were used as the model system. Studying the liquid gate effect and ionic concentration dependence of strepavidin sensing indicates that electrostatic interaction is the dominant mechanism for sensing response. Based on this sensing mechanism and transistor physics, a linear correlation between the absolute sensor response (DeltaI) and the gate dependence (dI(ds)/dV(g)) is predicted and confirmed experimentally. Using this correlation, a calibration method was developed where the absolute response is divided by dI(ds)/dV(g) for each device, and the calibrated responses from different devices behaved almost identically. Compared to the common normalization method (normalization of the conductance/resistance/current by the initial value), this calibration method was proven advantageous using a conventional transistor model. The method presented here substantially suppresses device-to-device variation, allowing the use of nanosensors in large arrays.

Electrochemical behaviors of guanosine on carbon ionic liquid electrode and its determination.

The electrochemical behaviors of guanosine on the ionic liquid of N-butylpyridinium hexafluorophosphate (BPPF(6)) modified carbon paste electrode (CPE) was studied in this paper and further used for guanosine detection. Guanosine showed an adsorption irreversible oxidation process on the carbon ionic liquid electrode (CILE) with the oxidation peak potential located at 1.12 V (vs. SCE) in a pH 4.5 Britton-Robinson (B-R) buffer solution. Compared with that on the traditional carbon paste electrode, small shift of the oxidation peak potentials appeared but with a great increment of the oxidation peak current on the CILE, which was due to the presence of ionic liquid in the modified electrode adsorbed the guanosine on the surface and promoted the electrochemical response. The electrochemical parameters such as the electron transfer coefficient (alpha), the electron transfer number (n), and the electrode reaction standard rate constant (k(s)) were calculated as 0.74, 1.9 and 1.26 x 10(-4)s(-1), respectively. Under the optimal conditions the oxidation peak current showed a good linear relationship with the guanosine concentration in the range from 1.0 x 10(-6) to 1.0 x 10(-4)mol/L by cyclic voltammetry with the detection limit of 2.61 x 10(-7)mol/L (3sigma). The common coexisting substances showed no interferences to the guanosine oxidation. The CILE showed good ability to distinguish the electrochemical response of guanosine and guanine in the mixture solution. The urine samples were further detected by the proposed method with satisfactory results.

A new method for electrocatalytic oxidation of ascorbic acid at the Cu(II) zeolite-modified electrode.

A new method is developed for the catalytic oxidation of ascorbic acid at graphite zeolite-modified electrode, doped with copper(II) (Cu(2+)A/ZCME). Copper(II) exchanged in zeolite type A acts as catalyst to oxidize ascorbic acid. The modified electrode lowered the overpotential of the reaction by approximately 400 mV. First, the electrochemical behavior of copper(II), incorporated in the zeolite type A modified electrode, was studied. The results illustrate that diffusion can control the copper(II)/copper(0) redox process at the Cu(2+)A/ZCME. Then, the behavior of electrocatalytic oxidation reaction for ascorbic acid was researched. The electrode was employed to study electrocatalytic oxidation of ascorbic acid, using cyclic voltammetry and chronoamperometry as diagnostic techniques. The diffusion coefficient of ascorbic acid was equal to 1.028 x 10(-5)cm(2)s(-1). A linear calibration graph was obtained over the ascorbic acid with a concentration range of 0.003-6.00 mmol L(-1). The detection limit (DL) of ascorbic acid was estimated as 2.76 x 10(-7)mol L(-1). The relative standard deviations of 10 replicate measurements (performed on a single electrode at several ascorbic acid concentrations between 3.0 and 200 micromol L(-1)) were measured between 1.0 and 2.4%.

Development and validation of an assay for iodide in serum using ion chromatography with pulsed amperometric detection.

We developed and validated an ion chromatography method to assay iodide in serum sampled from rats and rabbits that had been exposed to iodomethane. Iodomethane is of interest because it is a volatile liquid pre-plant soil crop protection fumigant that has been proposed as a non-ozone-depleting alternative to methyl bromide. Serum was prepared from whole blood collected on wet ice at the time of sacrifice and kept frozen at less than -65 degrees C. For analysis, serum samples were thawed unassisted at ambient temperature. Proteins were separated from the serum samples by ultrafiltration. A 100-microl filtered serum sample was then injected into the ion chromatograph without additional sample preparation. Iodide was separated in <20 min by anion-exchange chromatography using a 25-mM nitric acid eluent. The analyte of interest was detected by pulsed amperometry using a silver working electrode. The method showed linear response over the concentration range of 100 to 5000 ng/ml iodide (r2>.998) with a lower limit of quantitation of 100 ng/ml iodide. The accuracy of the procedure, determined by spiked recovery measurements at 100 ng/ml iodide, was between 90 and 110%. A method detection limit of 20 ng/ml for iodide in serum samples was demonstrated using the method of standard additions.

Polymers imprinted with PAH mixtures--comparing fluorescence and QCM sensors.

Molecular imprinting with binary mixtures of different polycyclic aromatic hydrocarbons (PAH) is a tool for design of chemically highly sensitive layers for detection of these analytes. Sensor responses increase by one order of magnitude compared with layers imprinted with one type of template. Detection limits, e.g. for pyrene, reach down to 30 ng L(-1) in water, as could be observed with a naphthalene and pyrene-imprinted polyurethane. Comparing sensor characteristics obtained by QCM and fluorescence reveals different saturation behaviours indicating that, first, single PAH molecules occupy the interaction centres followed by gradual excimer incorporation at higher concentrations finally leading to substantial quenching, when all accessible cavities are occupied. The plateau in the mass-sensitive measurements suggests that up to 80% of the cavities generated in the MIP are re-occupied. Displacement measurements between chrysene and pyrene revealed that for imprinted layers with very high pyrene sensitivities the signals of both PAH are additive, whereas in materials with lower pyrene uptake the two analytes replace each other in the interaction sites of the polymer.

Stripping analysis of nanomolar perchlorate in drinking water with a voltammetric ion-selective electrode based on thin-layer liquid membrane.

A highly sensitive analytical method is required for the assessment of nanomolar perchlorate contamination in drinking water as an emerging environmental problem. We developed the novel approach based on a voltammetric ion-selective electrode to enable the electrochemical detection of "redox-inactive" perchlorate at a nanomolar level without its electrolysis. The perchlorate-selective electrode is based on the submicrometer-thick plasticized poly(vinyl chloride) membrane spin-coated on the poly(3-octylthiophene)-modified gold electrode. The liquid membrane serves as the first thin-layer cell for ion-transfer stripping voltammetry to give low detection limits of 0.2-0.5 nM perchlorate in deionized water, commercial bottled water, and tap water under a rotating electrode configuration. The detection limits are not only much lower than the action limit (approximately 246 nM) set by the U.S. Environmental Protection Agency but also are comparable to the detection limits of the most sensitive analytical methods for detecting perchlorate, that is, ion chromatography coupled with a suppressed conductivity detector (0.55 nM) or electrospray ionization mass spectrometry (0.20-0.25 nM). The mass transfer of perchlorate in the thin-layer liquid membrane and aqueous sample as well as its transfer at the interface between the two phases were studied experimentally and theoretically to achieve the low detection limits. The advantages of ion-transfer stripping voltammetry with a thin-layer liquid membrane against traditional ion-selective potentiometry are demonstrated in terms of a detection limit, a response time, and selectivity.