Biomechanical impact of labiolingual diameter on endodontically treated anterior teeth with crown restoration under occlusal loading.

OBJECTIVE: To evaluate the effect of the labiolingual diameter and construction of an endodontically treated (ET) anterior tooth with crown restoration on stress distribution and biomechanical safety under occlusal loading. METHODOLOGY: Three-dimensional finite element models were generated for maxillary central incisors with all-ceramic crown restorations. The labiolingual diameters of the tooth, defined as the horizontal distance between the protrusion of the labial and lingual surfaces, were changed as follows: (D1) 6.85 mm, (D2) 6.35 mm, and (D3) 5.85 mm. The model was constructed as follows: (S0) vital pulp tooth; (S1) ET tooth; (S2) ET tooth with a 2 mm ferrule, restored with a fiber post and composite resin core; (S3) ET tooth without a ferrule, restored with a fiber post and composite resin core. A total of 12 models were developed. In total, two force loads (100 N) were applied to the crown's incisal edge and palatal surface at a 45° oblique angle to the longitudinal axis of the teeth. The Von Mises stress distribution and maximum stress of the models were analyzed. RESULTS: Regardless of the loading location, stress concentration and maximum stress (34.07~66.78MPa) in all models occurred in the labial cervical 1/3 of each root. Both labiolingual diameter and construction influenced the maximum stress of the residual tooth tissue, with the impact of the labiolingual diameter being greater. A reduction in labiolingual diameter led to increased maximum stress throughout the tooth. The ferrule reduced the maximum stress of the core of S2 models (7.15~10.69 MPa), which is lower compared with that of S3 models (19.45~43.67 MPa). CONCLUSION: The labiolingual diameter exerts a greater impact on the biomechanical characteristics of ET anterior teeth with crown restoration, surpassing the influence of the construction. The ferrule can reduce the maximum stress of the core and maintain the uniformity of stress distribution.

Erosive tooth wear inhibition by hybrid coatings with encapsulated fluoride and stannous ions.

This study aimed to formulate a hybrid coating material (HC) and to modify this HC with fluoride (NaF) and stannous (SnCl2) ions, directly or encapsulated in nano containers, testing the effects of these materials against dental erosion and erosion-abrasion. Enamel and dentin specimens were treated with the HCs, and then tested in erosion or erosion-abrasion cycling models of 5 days (n = 10 for each substrate, for each model). Deionized water was the negative control, and a fluoride varnish, the positive control. Surface loss (SL, in µm) was evaluated with an optical profilometer, and data were statistically analyzed (α = 0.05). For enamel, in erosion, the positive control and HC without additives showed significantly lower SL than the negative control (p = 0.003 and p = 0.001). In erosion-abrasion, none of the groups differed from the negative control (p > 0.05). For dentin, in erosion, the positive control, HC without additives, HC with non-encapsulated F, and HC with encapsulated F + Sn showed lower SL than the negative control (p < 0.05). In erosion-abrasion, none of the groups differed significantly from the negative control (p < 0.05). HC without additives showed a promising potential for protecting the teeth against dental erosion (with upward trend for improved protection on dentin), but not against erosion-abrasion. The presence of additives did not improve the protective effect of the HC, on both substrates.

Percepción estética de la posición anteroposterior de los incisivos superiores en relación con la frente / Esthetic perception of the anteroposterior position of upper incisors in relation to the forehead

RESUMEN Introducción: El tratamiento ortodóntico tiene como objetivos fundamentales el logro de relaciones oclusales estables y la mejora en la expresión de la sonrisa. Particularmente, la posición de los incisivos centrales superiores presenta un rol importante en esta expresión y se ha sugerido el uso de referencias extracraneales para su correcta posición tridimensional. Conocer las preferencias de los distintos actores sociales respecto a este factor puede ayudar a las decisiones en la planificación de los tratamientos. Objetivo: Evaluar la percepción estética que ortodoncistas, cirujanos dentistas y personas no expertas tienen de la sonrisa con el incisivo central superior en posición anteroposterior respecto a la frente y en norma lateral. Métodos: Se empleó una fotografía en norma lateral en sonrisa de una mujer peruana con perfil normal y posición anteroposterior del incisivo central superior ideal según el elemento II de la armonía orofacial de Andrews. La fotografía fue modificada digitalmente de tal forma que se obtuvieron imágenes con los incisivos retruídos (- 4 mm) y protruidos (+ 4 mm). Las fotografías fueron evaluadas por un panel conformado por ortodoncistas, cirujanos dentistas y personas no expertas. La evaluación se realizó a través de una escala visual análoga. Resultados: La fotografía con la posición normal del incisivo central superior con respecto a la línea GALL fue mejor valorada por los ortodoncistas (67,658 ± 22,094) y por los no expertos (54,038 ± 20,524). Los cirujanos dentistas consideraron más agradable la posición protruida (60,804 ± 3,626). Se encontraron diferencias significativas entre los grupos de evaluadores y las fotografías (p < 0,05). Conclusiones: Los ortodoncistas mostraron una valoración de la estética más cercana a la norma para la posición anteroposterior de los incisivos. La posición anteroposterior de los incisivos juega un rol importante en la percepción de la estética de la sonrisa en norma lateral(AU)

ABSTRACT Introduction: Orthodontic treatment is mainly aimed at achieving stable occlusal relationships and enhancing the smile expression. The position of the upper central incisors plays a particularly important role in such an expression, and extracranial references have been suggested for its proper three-dimensional position. Awareness of the preferences of the various social actors involved may be useful to make appropriate decisions when planning the treatments. Objective: Evaluate the esthetic perception that orthodontists, dental surgeons and laypeople have of the smile with the upper central incisor in anteroposterior position with respect to the forehead and in lateral norm. Methods: A lateral norm photograph was used of a Peruvian woman with a normal profile and ideal anteroposterior position of the upper central incisor according to element II of Andrews' orofacial harmony. The photograph was digitally modified to obtain images with retruding (- 4 mm) and protruding (+ 4 mm) incisors. The photographs were evaluated by a panel composed of orthodontists, dental surgeons and laypeople. The evaluation was based on a visual analog scale. Results: The photograph with normal position of the upper central incisor with respect to the GALL line was ranked higher by orthodontists (67.658 ± 22.094) and laypeople (54.038 ± 20.524). To dental surgeons the protruded position was nicer (60.804 ± 3.626). Significant differences were found between the groups of evaluators and the photographs (p < 0.05). Conclusions: The esthetic appraisal of orthodontists was closer to the norm for anteroposterior position of incisors. The anteroposterior position of incisors plays an important role in the esthetic perception of the smile in the lateral norm(AU)

Relationship between cervical vertebral maturation and dental development in a sample of yemeni children and adolescents / Relación entre la maduración vertebral cervical y el desarrollo dental en una muestra de niños y adolescentes yemeníes

Objective: This study was conducted to investigate the relationship between dental development and cervical vertebral maturation stages in a group of Yemeni children and adolescents. Materials an Methods: The study included digital panoramic radiographs and lateral skull cephalograms obtained from 207 Yemeni subjects­122 females and 85 males aged between 8 to 18 years. Dental maturity was evaluated according to the method of Demirijian et al., calcification stages of the left mandibular canines, first and second premolars and second molars were assessed. Skeletal maturity was assessed by the cervical vertebral maturation (CVM) stages according to the method of Baccetti et al. Correlation between CVM and dental maturation was evaluated by Spearman rank-order correlation coefficient (SROCC). Results: CVM and dental calcification stages were highly correlated (p<0.001) in both genders, ranging from 0.686 to 0.873 for females and 0.787 to 0.871 for males. Calcification stages of the second molars showed the strongest correlation with CVM. Conclusion: Calcification stages of the second molar may be used as a reliable maturation indicator. Dental maturation may be applied to determine the skeletal maturity status of Yemeni children and adolescents.

Objetivo: Este estudio se realizó para investigar la relación entre el desarrollo dental y las etapas de maduración vertebral cervical en un grupo de niños y adolescentes yemeníes. Material y Métodos: El estudio incluyó radiografías panorámicas digitales y cefalogramas laterales del cráneo obtenidos de 207 sujetos yemeníes: 122 mujeres y 85 hombres de entre 8 y 18 años. La madurez dental se evaluó de acuerdo con el método de Demirijian et al. Se evaluaron las etapas de calcificación de los caninos mandibulares izquierdos, primer y segundo premolares y segundos molares. La madurez esquelética se evaluó mediante las etapas de maduración vertebral cervical (CVM) de acuerdo con el método de Baccetti et al. La correlación entre la CVM y la maduración dental se evaluó mediante el coeficiente de correlación de orden de rango de Spearman (SROCC). Resultado: Las etapas de CVM y calcificación dental estuvieron altamente correlacionadas (p<0.001) en ambos sexos, con un rango de 0.686 a 0.873 para las mujeres y 0.787 a 0.871 para los hombres. Las etapas de calcificación de los segundos molares mostraron la correlación más fuerte con CVM. Conclusión: las etapas de calcificación del segundo molar pueden usarse como un indicador de maduración confiable. La maduración dental puede aplicarse para determinar el estado de madurez esquelética de los niños y adolescentes yemeníes.

Precision brackets for upper lateral incisors in Bioprogressive therapy.

Orthodontic brackets, specifically in their slots, are responsible for receiving active orthodontic forces and transferring them to the teeth to be moved. The presence of an altered slot or inaccurate dimensions can influence the mechanical relationship between the bracket and archwire, interfering with the biomechanics of tooth movement. The objective of this study was by comparing the accuracy of slot placement of upper right lateral incisor metal brackets for Bioprogressive Ricketts therapy from five trademarks. The following characteristics were evaluated: height, torque, and internal parallelism of the walls of the slot. The sample included 75 brackets, 15 each from the following trademarks: 3M Abzil, Forestadent, Morelli Rocky Mountain Orthodontics, and Tecnident. Images of the slot profiles were obtained through standardized techniques using scanning electron microscopy, measured by the AutoCAD 2017 software, and compared to Ricketts prescription, respecting standard deviation with the technical and tolerance parameters present in standard ISO 27020. The results indicated that most of the evaluated characteristics were in accordance with the standard parameters, considering the tolerance adopted. There were exceptions found to this pattern of precision in the 3M Abzil brackets with regard to torque variation, and the Morelli brackets in relation to height variation and parallelism between the walls of the slot. Considering the measured dimensional characteristics, the metal brackets used in Bioprogressive Ricketts therapy has satisfactory pattern accuracy; however, there are still some specific inaccuracies in brackets from certain brands that can require more attention during the detailing phase.

Stress analysis of maxillary central incisors endodontically -treated with varying ferrule heights and three different post dowel materials - a finite element analysis / Análisis de tensión de los incisivos centrales superiores tratados endodónticamente con diferentes alturas de férula y tres materiales diferentes de clavija posterior: un análisis de elementos finitos

Statement of problem : fracture of endodontically treated teeth is reduced by the use of a post with ferrule, but the effect of different ferrule configurations and dowel materials is not clear. Purpose: to evaluate the effect of ferrules with different configurations and heights on the stress of endodontically treated teeth restored with three different post and dowel materials. Materials and Methods: fifteen models of maxillary central incisors restored with porcelain fused to metal crowns were obtained using pro engineer software. the models were divided into three groups, each consisting of five models with ferrule heights of 0mm, 2mm, 4mm, 2mm with oblique fracture, 4mm with oblique fracture, the models under group GFR were restored with fiberglass reinforced post (GFR) and composite core build-up, group NiCr with a custom cast post metal alloy (NiCr), and group Zr with zirconia post (Zr) and composite core build-up. an oblique load of 100N and 150N at an angle of 135 degrees was applied to the palatal surface of the tooth, a vertical load of 100N and 150N at an angle of 90 degrees was applied to the incisal tip of the tooth. The maximum principal stress and the von mises stress was calculated for the remaining tooth structure and post apex using the finite element analysis (FEA) software. Results: the maximum von misses stress was observed in the apex of the post (p<0.05). Group Zr showed the highest mean stress (6.39Mpa) followed by group NiCr (5.65Mpa). There was a significant difference between post and between NiCr and Zr post for 2mm and 4mm ferrule height, while for 0mm ferrule there was a significant difference between the GFR and NiCr groups (p<0.05). Under oblique load, the maximum mean stress was observed in remaining tooth structures while for vertical load, it was observed at the apex of the post. Regarding ferrule heights, there were significant differences between 0mm-2mm, and 0mm-4mm uniform ferrule in post apex in the case of NiCr posts (p<0.05). Absence of ferrule resulted in higher stress for the NiCr group. Conclusion: higher loads that led to fracture were observed only at the apex of the post. Zirconia posts (group Zr) had higher fracture loads, whereas absence of ferrule resulted in higher fracture load with custom cast posts (group NiCr). Fracture thresholds were high on the remaining tooth structure for all the dowel systems especially for composite core build up irrespective of ferrule height and configuration. Clinical implications: appropriate selection of post and dowel materials in different configurations of ferrule heights ensures clinical success.

Indicación del problema: la fractura de los dientes tratados endodónticamente se reduce mediante el uso de un poste con férula, pero el efecto de diferentes configuraciones de férula y materiales de clavija no está claro. Propósito: evaluar el efecto de los casquillos con diferentes configuraciones y alturas sobre el estrés de los dientes tratados endodónticamente restaurados con tres materiales diferentes de postes y tacos. materiales y métodos: quince modelos de incisivos centrales superiores restaurados con porcelana fundida a coronas de metal se obtuvieron con el software Pro Engineer. Los modelos se dividieron en tres grupos, cada uno de los cuales consta de cinco modelos con alturas de casquillo de 0mm, 2mm, 4mm, 2mm con fractura oblicua, 4mm con fractura oblicua. los modelos del grupo GFR fueron restaurados con poste reforzado con fibra de vidrio (GFR) y acumulación de núcleo compuesto, grupo nicr con una aleación de metal de poste fundido personalizado (NiCr) y grupo Zr con poste de zirconia (Zr) y acumulación de núcleo compuesto. se aplicó una carga oblicua de 100N y 150N en un ángulo de 135º a la superficie palatina del diente. se aplicó una carga vertical de 100N y 150N en un ángulo de 90º a la punta incisal del diente. la tensión principal máxima y la tensión de von mises se calcularon para la estructura dental restante y después del vértice utilizando el software de análisis de elementos finitos (FEA). Resultados: el estrés máximo de von falta se observó en el vértice de la publicación (p<0.05). El grupo Zr mostró el mayor estrés medio (6.39Mpa) seguido del grupo NiCr (5.65Mpa). Hubo una diferencia significativa entre la publicación NiCr y Zr para la altura de la férula de 2mm y 4mm, mientras que para la férula de 0mm hubo una diferencia significativa entre los grupos GFR y NiCr (p<0,05), bajo la carga oblicua, la tensión media máxima en las estructuras dentales restantes, mientras que para la carga vertical, se observó en el vértice del poste. En cuanto a las alturas de la férula, hubo diferencias significativas entre la férula uniforme de 0mm-2mm y de 0mm-4mm en el post-apex en el caso de los postes de NiCr (p<0.05), la ausencia de férula dio como resultado un mayor estrés para el grupo NiCr. Conclusión: las cargas más altas que llevaron a la fractura se observaron solo en el vértice del poste; Los postes de zirconia (grupo Zr) tuvieron mayores cargas de fractura, mientras que la ausencia de férula dio como resultado una mayor carga de fractura con postes moldeados personalizados (NiCr de grupo). Los umbrales de fractura fueron altos en la estructura dental restante para todos los sistemas de clavijas, especialmente para la acumulación de núcleos compuestos independientemente de la altura y configuración de la férula. Implicaciones clínicas: la selección adecuada de materiales de postes y tacos en diferentes configuraciones de alturas de férulas asegura el éxito clínico.

Maxillary dentoalveolar assessment following retraction of maxillary incisors: a preliminary study.

OBJECTIVE:: The aim of this preliminary study was to assess changes in tooth length and alveolar thickness following retraction of maxillary incisors. METHODS:: A total of 11 patients presenting severe maxillary dentoalveolar protrusion revealed by initial (T1) cone-beam computed tomography (CBCT), and whose treatment plan included extraction of maxillary first premolars and retraction of maxillary incisors, were selected and submitted to CBCT examination one month after the end of incisors retraction (T2). The premaxilla was assessed through seven axial slices by means of Dolphin ImagingTM software. In each of these slices, five measurements of the distance from the buccal cortical bone to the palatal cortical bone were performed. Tooth length of maxillary incisors (n = 44) was also measured in sagittal slices. Measurements were repeated after a two-week interval, and intraclass correlation coefficient (ICC) was used to test examiner calibration. Wilcoxon test was used to detect differences in measurements performed at the two time intervals. RESULTS:: The ICC was satisfactory for tooth length (0.890) and for premaxilla alveolar thickness measurements (0.980). Analysis of data showed no statistically significant differences (p > 0.05) in tooth length or alveolar thickness between the two-time intervals assessed. CONCLUSION:: The force used in retraction of maxillary incisors in this research did not promote significant changes in tooth length of maxillary incisors or in premaxilla alveolar thickness.

Maxillary dentoalveolar assessment following retraction of maxillary incisors: a preliminary study

ABSTRACT Objective: The aim of this preliminary study was to assess changes in tooth length and alveolar thickness following retraction of maxillary incisors. Methods: A total of 11 patients presenting severe maxillary dentoalveolar protrusion revealed by initial (T1) cone-beam computed tomography (CBCT), and whose treatment plan included extraction of maxillary first premolars and retraction of maxillary incisors, were selected and submitted to CBCT examination one month after the end of incisors retraction (T2). The premaxilla was assessed through seven axial slices by means of Dolphin ImagingTM software. In each of these slices, five measurements of the distance from the buccal cortical bone to the palatal cortical bone were performed. Tooth length of maxillary incisors (n = 44) was also measured in sagittal slices. Measurements were repeated after a two-week interval, and intraclass correlation coefficient (ICC) was used to test examiner calibration. Wilcoxon test was used to detect differences in measurements performed at the two time intervals. Results: The ICC was satisfactory for tooth length (0.890) and for premaxilla alveolar thickness measurements (0.980). Analysis of data showed no statistically significant differences (p > 0.05) in tooth length or alveolar thickness between the two-time intervals assessed. Conclusion: The force used in retraction of maxillary incisors in this research did not promote significant changes in tooth length of maxillary incisors or in premaxilla alveolar thickness.

RESUMO Objetivo: o objetivo deste estudo preliminar foi avaliar as alterações no comprimento dentário e na espessura alveolar durante a retração dos incisivos superiores. Métodos: um total de 11 pacientes apresentando protrusão dentoalveolar severa, de acordo com a tomografia computadorizada de feixe cônico (TCFC) inicial (T1), e que continham no seu plano de tratamento extração dos pré-molares superiores e retração dos incisivos superiores, foram selecionados e submetidos a exames de TCFC um mês após o término da retração dos incisivos (T2). Com o auxílio do software Dolphin Imaging(r), a prémaxila foi dividida em sete cortes axiais. Em cada corte axial, foram realizadas cinco medições da distância da cortical vestibular a lingual. O comprimento dos incisivos superiores (n = 44) foi medido no corte sagital. As medições foram refeitas após o intervalo de duas semanas e o coeficiente de correlação intraclasse (ICC) foi utilizado para avaliar a calibração do examinador. Utilizou-se o teste de Wilcoxon para detectar diferenças nas medições realizadas nos dois intervalos de tempo. Resultados: o ICC mostrou-se satisfatório tanto para o comprimento dentário (0,890) quanto para a espessura alveolar da pré-maxila (0,980). Não foram observadas diferenças estatísticas significativas para comprimento dentário e para as espessuras alveolares (p < 0,05) nos períodos avaliados. Conclusões: as forças atuantes na retração dos incisivos, nessa pesquisa, não provocaram alterações significativas no comprimento dentário dos incisivos superiores, nem mudanças na espessura alveolar da pré-maxila.

Fracture Strength of Aged Monolithic and Bilayer Zirconia-Based Crowns.

The purpose of this study was to evaluate the effect of design and surface finishing on fracture strength of yttria-tetragonal zirconia polycrystal (Y-TZP) crowns in monolithic (1.5 mm thickness) and bilayer (0.8 mm zirconia coping and 0.7 mm porcelain veneer) configuration after artificial aging. Bovine incisors received crown preparation and Y-TZP crowns were manufactured using CAD/CAM technique, according to the following groups (n = 10): Polished monolithic zirconia crowns (PM); Glazed monolithic zirconia crowns (GM); Bi-layer crowns (BL). Crowns were cemented with resin cement, submitted to artificial aging in a chewing simulator (2.5 million cycles/80 N/artificial saliva/37 °C), and tested for fracture strength. Two remaining crowns referring to PM and GM groups were submitted to a chemical composition analysis to measure the level of yttrium after aging. One-way ANOVA and Tukey's test (P = .05) indicated that monolithic zirconia crowns presented similar fracture strength (PM = 3476.2 N ± 791.7; GM = 3561.5 N ± 991.6), which was higher than bilayer crowns (2060.4 N ± 810.6). There was no difference in the yttrium content among the three surfaces evaluated in the monolithic crowns. Thus, monolithic zirconia crowns present higher fracture strength than bilayer veneered zirconia after artificial aging and surface finishing does not affect their fracture strength.

Evaluation of the force applied by the tongue and lip on the maxillary central incisor tooth.

PURPOSE: To describe the development and testing of a system that measures forces exerted by the tongue and upper lip on a tooth during rest and during swallowing. METHODS: Twenty-eight subjects, aged 19-31 years (mean: 23.2 years) were submitted to measurement of forces exerted by the upper lip and tongue on the maxillary right central incisor tooth. Flexiforce resistive sensors were fixed on the labial and lingual surfaces of the tooth. They were connected to an amplifier circuit and a data acquisition board for processing and transmitting information to a computer. RESULTS: At rest, the tongue force on the tooth was 0.00±0.00 N and the lip force on tooth was 0.02±0.02 N. The difference between them was significant. During swallowing, the values were 0.31±0.38 N and 0.15±0.14 N, for the tongue and lip, respectively. This difference was not significant. CONCLUSION: At rest, the lip exerts a larger force than the tongue on the maxillary right central incisor tooth. During swallowing, there was no difference between lip and tongue force on the tooth.

Segmented arch or continuous arch technique? A rational approach.

This study aims at revising the biomechanical principles of the segmented archwire technique as well as describing the clinical conditions in which the rational use of scientific biomechanics is essential to optimize orthodontic treatment and reduce the side effects produced by the straight wire technique.

Evaluation of the force applied by the tongue and lip on the maxillary central incisor tooth

PURPOSE: To describe the development and testing of a system that measures forces exerted by the tongue and upper lip on a tooth during rest and during swallowing. METHODS: Twenty-eight subjects, aged 19-31 years (mean: 23.2 years) were submitted to measurement of forces exerted by the upper lip and tongue on the maxillary right central incisor tooth. Flexiforce resistive sensors were fixed on the labial and lingual surfaces of the tooth. They were connected to an amplifier circuit and a data acquisition board for processing and transmitting information to a computer. RESULTS: At rest, the tongue force on the tooth was 0.00±0.00 N and the lip force on tooth was 0.02±0.02 N. The difference between them was significant. During swallowing, the values were 0.31±0.38 N and 0.15±0.14 N, for the tongue and lip, respectively. This difference was not significant. CONCLUSION: At rest, the lip exerts a larger force than the tongue on the maxillary right central incisor tooth. During swallowing, there was no difference between lip and tongue force on the tooth. .

Segmented arch or continuous arch technique? A rational approach

This study aims at revising the biomechanical principles of the segmented archwire technique as well as describing the clinical conditions in which the rational use of scientific biomechanics is essential to optimize orthodontic treatment and reduce the side effects produced by the straight wire technique.

O objetivo desse trabalho é revisar os princípios biomecânicos da técnica do arco segmentado, bem como descrever situações clínicas onde o uso racional da biomecânica científica é fundamental na otimização do tratamento ortodôntico e eliminação dos efeitos colaterais da abordagem com arco contínuo.

Biomechanical evaluation of platform switching: different mismatch sizes, connection types, and implant protocols.

BACKGROUND: It is not yet well understood to what extent different implant-abutment mismatch sizes and implant-abutment connection types may influence the peri-implant biomechanical environment of implants in different clinical situations. METHODS: Computed tomography-based finite element models comprising a maxillary central incisor socket and 4.5 × 13 mm outer-diameter implants with external and internal hex connection types were constructed. The abutments were designed with diameters of 3.5 mm (platform switching [PS] with 1 mm of diametral mismatch [PS - 1]), 4.0 mm (PS with 0.5 mm of diametral mismatch [PS - 0.5]), and 4.5 mm (conventional matching implant-abutment design [CD]). Analysis of variance at the 95% confidence interval was used to evaluate peak equivalent strain (EQV strain) in the bone, bone volume affected by a strain >4,000 µÎµ (EQV strain >4,000 µÎµ), the peak von Mises stress (EQV stress) in abutment screw, and the bone-implant relative displacement. RESULTS: Similar bone strain levels (EQV strain and EQV strain >4,000 µÎµ) were encountered in PS - 1, PS - 0.5, and CD models for immediately placed implants, independent of the connection type. For immediately loaded implants, slightly smaller peak EQV strain and EQV strain >4,000 µÎµ were found for PS - 1. However, for both connection types in osseointegrated models, the higher the mismatch size, the lesser the amount of strain found. CONCLUSIONS: The increase in mismatch size of PS configuration results in a significant decrease of strain levels in bone for osseointegrated implants, principally for external hex connections. No significant effect of PS could be noted in immediately placed implants.

Traumatismo dentário em adolescentes entre 15 e 19 anos na cidade do Recife / PE e fatores associados - estudo preliminar / Traumatic tooth injuries and associated factors in adolescents aged 15 to 19 years in Recife/PE/Brazil - a preliminary study

Objetivo: avaliar a prevalência de traumatismo dentário e fatores associados em adolescentes de 15 a 19 anos da cidade do Recife/PE. Metodologia: a amostra foi composta por 148 adolescentes de ambos os sexos. Os dados foram coletados por meio de exames clínicos e entrevistas realizadas nos intervalos das aulas. Os testes Qui-quadrado de Pearson e Exato de Fisher foram utilizados para verificar a associação entre as variáveis. O nível de significância utilizado foi de 5%. A prevalência encontrada foi de aproximadamente 15%. Resultados: os dentes mais afetados foram os incisivos centrais superiores. A maioria dos adolescentes apresentou um único dente atingido por trauma. As principais causas de trauma dental foram: brincando com outras pessoas (45,5%) e quedas (18,2%). Não houve associação entre a presença de traumatismo dental e overjet acentuado e/ou cobertura labial inadequada. Não foi observada diferença estatística entre prevalência de traumatismo e o sexo dos adolescentes. O tipo de escola não foi associado à presença de traumatismo.Conclusão: a prevalência de traumatismo dental em adolescentes de 15 a 19 anos de idade da cidade do Recife foi relativamente alta, porém não foi observada associação entre overjet e cobertura labial...

Objective: To evaluate the prevalence of traumatic tooth injuries and associated factors in Adolescents aged 15 to 19 years in the city of Recife, PE, Brazil. Method: The sample consisted of 148 adolescents of both genders. Data were collected by clinical examinations and interviews conductedbetween classes. Pearson?s chi-square and Fisher?s exact tests were used to assess the association among the variables. The significance level was set at 5%. The prevalence was approximately 15%. Results: The most affected teeth were the maxillary central incisors. Most adolescents had a single hit tooth trauma. The main causes of dental trauma were playing with someone (45.5%) and falls (18.2%). There was no association between dental trauma and severe overjetand/or inadequate lip coverage. There was no statistically significant difference (p>0.05) between the prevalence of trauma and gender of the adolescents. The type of school was not associated with the presence of traumatic tooth injuries. Conclusion: The prevalence of dental trauma in adolescents aged 15 to 19 years in Recife was relatively high, but no association was foundbetween overjet and lip coverage...

Prospective clinical assessment of pulp sensitivity after chin bone harvesting.

PROPOSAL: Evaluate pulp vitality of mandibular teeth after chin bone harvesting. MATERIALS AND METHODS: Thirty patients underwent chin bone harvesting and accompanied for 12 months, being submitted to testing for pulp vitality with Endo Ice refrigerant spray to produce a local temperature of -50 °C. The statistical analysis was executed with McNemar test with P value < 0.05. RESULTS: Results show that canine teeth are most susceptible to alterations; 68.82% (181) of the teeth tested showed no loss of pulp sensitivity to cold 30 days after surgery (P < 0.05), and at the end of the study, that figure had risen to 100% (263) of all teeth included in the sample. CONCLUSIONS: Pulp vitality testing showed that 31.18% (82) of teeth experienced some loss of sensitivity, but by 12 months after surgery, all teeth had recuperated their pulp sensitivity to cold unaided.

Influence of platform and abutment angulation on peri-implant bone. A three-dimensional finite element stress analysis.

The aim of this study was to evaluate stress distribution on the peri-implant bone, simulating the influence of Nobel Select implants with straight or angulated abutments on regular and switching platform in the anterior maxilla, by means of 3-dimensional finite element analysis. Four mathematical models of a central incisor supported by external hexagon implant (13 mm × 5 mm) were created varying the platform (R, regular or S, switching) and the abutments (S, straight or A, angulated 15°). The models were created by using Mimics 13 and Solid Works 2010 software programs. The numerical analysis was performed using ANSYS Workbench 10.0. Oblique forces (100 N) were applied to the palatine surface of the central incisor. The bone/implant interface was considered perfectly integrated. Maximum (σmax) and minimum (σmin) principal stress values were obtained. For the cortical bone the highest stress values (σmax) were observed in the RA (regular platform and angulated abutment, 51 MPa), followed by SA (platform switching and angulated abutment, 44.8 MPa), RS (regular platform and straight abutment, 38.6 MPa) and SS (platform switching and straight abutment, 36.5 MPa). For the trabecular bone, the highest stress values (σmax) were observed in the RA (6.55 MPa), followed by RS (5.88 MPa), SA (5.60 MPa), and SS (4.82 MPa). The regular platform generated higher stress in the cervical periimplant region on the cortical and trabecular bone than the platform switching, irrespective of the abutment used (straight or angulated).

Biting performance and skull biomechanics of a chisel tooth digging rodent (Ctenomys tuconax; Caviomorpha; Octodontoidea).

Biting performance is a key factor in vertebrate groups possessing particular food habits. In subterranean rodents that use the incisors as a digging tool, apart from requirements related to gnawing abrasive diets, the force exerted at the incisors tips must be sufficient to break down soils that are often exceedingly compact. The subterranean genus Ctenomys diversified in the southern portion of South America closely associated with the relatively open environments that characterize that region. This genus is considered a "claw and chisel tooth digger," that is, during the excavation of their galleries, the animals break down the soil with both the fore-claws and the incisors. We report here measurements of in vivo bite force in one of the largest species of the genus, C. tuconax, which occupies highland grasslands with compacted soils. We document the combined use of claws and incisors observed under field conditions, also providing measurements of soil compaction in the habitat occupied by this species. We report estimates of bite force at the level of the incisors and cheek teeth calculated from the physiological cross-sectional area of jaw muscles. To this aim, anatomical and biomechanical analyses of the mandibular apparatus were performed in preserved specimens. We found that C. tuconax bites with a higher force than expected for a mammal of its size. To assess anatomical correlates of biting performance, the morphology of the skull and jaw, and incisor second moment of area were compared with those of other caviomorph rodents with different lifestyle.

Sexual selection in a polygynous rodent (Ctenomys talarum): an analysis of fighting capacity.

The South American subterranean rodent genus Ctenomys (Caviomorpha: Octodontoidea), which uses both claws and teeth to dig, shows striking morphological adaptations to its specialized mode of life. Among other traits, the genus has evolved a powerful jaw musculature and procumbent incisors that are used for dento-excavation. Behavioral observations indicate that these traits are also used during male aggressive encounters, which characterize the polygynous mating system of one of the species of the genus, Ctenomys talarum. A question emerges about sexual selection: could it have induced further changes in traits primarily evolved as adaptations for digging? To address this issue, we studied functional and morphological attributes of the jaw and incisors in specimens of C. talarum. Incisor bite forces were measured on wild females and males from a local population (Mar de Cobo; Buenos Aires Province) by means of a strain gauge load cell force transducer. Museum specimens coming from the same population were studied to assess anatomical attributes of both sexes. Since this species exhibits dimorphism in body size, the possible effect of body mass on the studied traits was analyzed. Males and females showed significant differences in biting performance and mandibular width, but when size was taken into account these differences disappeared. However, other dimorphic traits can vary with a certain independence with respect to size, particularly the 2nd moment of area of the incisors and, to a lesser extent, incisor procumbency. The former geometrical parameter, which is proportional to the bending strength, was highly dimorphic. This fact suggests that, during aggressive encounters between males, biting would place large bending loads on the incisors.