Sol-gel and Pechini niobium modified: synthesis, characterization and application in the 2,4-D herbicide degradation.

In this work, a comparison was made between the synthesis of niobium-based materials (Nb2O5), both in terms of material characterization and catalytic performance. The methods used were chemical mixtures: modified sol-gel and Pechini. The materials were calcined at different temperatures (753, 873 and 993K) and characterized by the following techniques: photoacousticspectroscopy (PAS), zero charge point (pHPZC), scanning electron microscopy (SEM/EDS), thermogravimetric analysis (TGA/DTG) and X-ray diffraction (XRD). The photocatalytic process was carried out to evaluate the degradation of 2,4-dichlorophenoxyacetic acid (2,4-D) under UV radiation (250 W mercury vapor lamp) and different experimental conditions. In addition, to better understand the influence of parameters such as pH, catalyst concentration (0.2, 0.5 and 0.8 g L-1) and calcination temperature, a Design of Experiments (DoE) was used. The results indicated that despite having similar structures and phases in the XRD analysis, the morphology presents two distinct surfaces, due to the preparation method. Differences in the synthesis method affected the catalytic activity in the parameters studied. Although the zero charge point values are close (6.18-6.36), we observed differences in the band gap depending on the calcination temperature. In the optimal condition studied, the catalyst prepared by the sol-gel method obtained the best results.

Using rice husk ash as a SiO2 source in the preparation of SiO2/Nb2O5 and SiO2/ZnS heterostructures for photocatalytic application.

This work presents the synthesis of SiO2/Nb2O5 and SiO2/ZnS heterostructures using the microwave-assisted hydrothermal (MAH) method, which is fast and has low temperature. The silica used in the synthesis was obtained by burning the rice husk without any pre- or post-treatments. The obtained samples were characterized using various techniques such as X-ray diffraction (XRD), energy-dispersive X-ray analysis (EDX), scanning electron microscopy (SEM), Fourier transform infrared (FTIR), and UV-visible. The obtained silica was found to be amorphous, and the materials used for modification showed characteristic of the type of synthesis used. SEM images showed that Nb2O5 and ZnS interacted with the SiO2 surface, filling the voids. In the photocatalytic process, the heterostructures showed enhanced decolorization efficiency for dyes such as rhodamine B (RhB) and methylene blue (MB) compared to SiO2. For RhB, the silica decolorized approximately 24%, and for MB, it discolored approximately 27%; SiO2/Nb2O5 showed 91.24% decolorization efficiency for RhB and 72.77% MB, while SiO2/ZnS showed approximately 96% for RhB and 100% for MB. All samples were tested under the same conditions. This demonstrates that the use of rice husk residue not only improves the photocatalytic activity of heterostructures but also promotes the utilization of improperly discarded residues.

Orthodontic resins loaded with niobium silicate particles: Impact of filler concentration on the physicochemical and biological properties.

OBJECTIVES: White spot lesions (WSL) are prevalent in patients using orthodontic appliances. The presence of ion-releasing compounds in the tooth-appliance interface may limit enamel demineralization to control WSL incidence. Thus, this study aims to evaluate the mineral formation on SiNb-containing experimental orthodontic resins and the influence of these fillers on the physicochemical and biological properties of developed materials. MATERIALS AND METHODS: The SiNb particles were synthesized via the sol-gel route and characterized by their molecular structure and morphology. Photopolymerizable orthodontic resins were produced with a 75 wt% Bis-GMA/25 wt% TEGDMA and 10 wt%, 20 wt%, or 30 wt% addition of SiNb. A control group was formulated without SiNb. These resins were tested for their degree of conversion, softening in solvent, cytotoxicity in fibroblasts, flexural strength, shear bond strength (SBS), and mineral deposition. RESULTS: The addition of 10 wt% of SiNb did not impair the conversion of monomers, cytotoxicity, and flexural strength. All groups with SiNb addition presented similar softening in solvent. The presence of these particles did not affect the bond strength between metallic brackets and enamel, with SBS values ranging from 16.41 to 18.66 MPa. The mineral deposition was observed for all groups. CONCLUSION: The use of niobium silicate as filler particles in resins may be a strategy for the adhesion of orthodontic appliances. The 10 wt% SiNb concentration resulted in a material with suitable physicochemical and biological properties while maintaining the bond strength to tooth enamel and promoting mineral deposition.

Cu/Nb2O5, Fe/Nb2O5 and Cu-Fe/Nb2O5 applied in salicylic acid degradation: Parameters studies and photocatalytic activity.

This study describes the synthesis of Cu/Nb2O5, Fe/Nb2O5, and Cu-Fe/Nb2O5 catalysts obtained by incorporating copper and/or iron metals into niobium pentoxide (Nb2O5). The new materials were characterized by the following techniques: Thermogravimetric Analysis (TA), surface and pore analysis, X-ray diffractometry (XRD), and Fourier Transform Infrared Spectroscopy (FT-IR). The catalyst was applied in the photocatalytic degradation of salicylic acid (SA). The influence of different parameters (calcined temperature, pH, and metal addition) on the photocatalytic reaction was evaluated. The results indicated that catalysts containing copper were more active and pH influenced the SA degradation process. SA removal results indicated that Cu/Nb2O5 photocatalyst presented a 1.5 fold higher degradation after 120 min in comparison to Cu-Fe/Nb2O5 and 4.6 fold higher than Fe/Nb2O5 catalyst, all them calcined at 400 °C. In tests carried out in the presence of formic acid, increasing the pH from about 3 to 7 allowed an almost 3.4-fold increase in SA degradation for the Cu-Fe/Nb2O5 catalyst calcined at 400 °C.

Preparation and characterization of novel as-cast Ti-Mo-Nb alloys for biomedical applications.

Ti and its alloys are the most used metallic biomaterials devices due to their excellent combination of chemical and mechanical properties, biocompatibility, and non-toxicity to the human body. However, the current alloys available still have several issues, such as cytotoxicity of Al and V and high elastic modulus values, compared to human bone. ß-type alloys, compared to α-type and (α + ß)-type Ti alloys, have lower elastic modulus and higher mechanical strength. Then, new biomedical ß-type alloys are being developed with non-cytotoxic alloying elements, such as Mo and Nb. Therefore, Ti-5Mo-xNb system alloys were prepared by argon arc melting. Chemical composition was evaluated by EDS analysis, and the density measurements were performed by Archimedes' method. The structure and microstructure of the alloys were obtained by X-ray diffraction and optical and scanning electron microscopy. Microhardness values were analyzed, and MTT and crystal violet tests were performed to assess their cytotoxicity. As the Nb concentration increases, the presence of the ß-Ti phase also grows, with the Ti-5Mo-30Nb alloy presenting a single ß-Ti phase. In contrast, the microhardness of the alloys decreases with the addition of Nb, except the Ti-5Mo-10Nb alloy, which has its microhardness increased probably due to the ω phase precipitation. Biological in-vitro tests showed that the alloys are not cytotoxic.

Low Mg content on Ti-Nb-Sn alloy when in contact with eBMMSCs promotes improvement of its biological functions.

Magnesium is a metal used in the composition of titanium alloys and imparts porosity. Due to its osteoconductive, biocompatible and biodegradable characteristics, its application in the development of biomedical materials has become attractive. This study aimed to evaluate the influence of magnesium present in porous Ti-Nb-Sn alloys, which have a low elastic modulus in adhesive, osteogenic properties and the amount of reactive intracellular oxygen species released in mesenchymal stem cells derived from bone marrow equine bone (eBMMSCs). Mechanical properties of the alloy, such as hardness, compressive strength and elastic modulus, were analyzed, as well as surface morphological characteristics through scanning electron microscopy. The evaluation of magnesium ion release was performed by atomic force spectroscopy. The biological characteristics of the alloy, when in contact with the alloy surface and with the culture medium conditioned with the alloy, were studied by SEM and optical microscopy. Confirmation of osteogenic differentiation by alizarin red and detection of ROS using a Muse® Oxidative Stress Kit based on dihydroetide (DHE). The alloy showed an elastic modulus close to cortical bone values. The hardness was close to commercial Ti grade 2, and the compressive strength was greater than the value of cortical bone. The eBMMSCs adhered to the surface of the alloy during the experimental time. Osteogenic differentiation was observed with the treatment of eBMMMSCs with conditioned medium. The eBMMSCs treated with conditioned medium decreased ROS production, indicating a possible antioxidant defense potential of magnesium release.

New insights of Nb2O5-based coatings on the 316L SS surfaces: enhanced biological responses.

This communication aims to propose new insights of Nb2O5-based coatings on the 316L SS surface with great prospects to be used in the dentistry field as brackets. The Nb2O5 thin film was incorporated into the 316L SS by using PVD method. For this purpose, the studied system was characterized structurally and morphologically by using AFM, FTIR-IRRAS, Raman spectroscopy and X-ray photoelectron spectroscopy (XPS). Biological assays were performed using human gingival fibroblast cell-line HGF-1. In agreement with FTIR and Raman results, the XPS technique indicates that Nb is present in an oxidation state assigned to Nb2O5. Furthermore, the coatings produced by PVD technique are less toxic and induces less inflammation in gingival cells (cell-line HGF-1), suggesting the strategy of use Nb2O5 thin film to cover the 316L SS promoted since its protection of the physiological environment to its biocompatibility improvement.

Nb-MCM-Type Mesoporous Material Synthesis Using Ionic Solid as Structure-Directing Agent for In Situ Lipase Immobilization.

MCM-41 and MCM-48 with niobium were successfully synthesized using 1-tetradecyl-3-methylimidazolium chloride ([C14MI]Cl) as a structure-directing agent. The best Si/Nb molar ratio was chosen (Si/Nb = 20) and the CALB enzyme was immobilized in situ in the synthesized Nb-MCM. SEM micrographs showed the formation of very regular spherical agglomerates with a diameter between 0.25 and 0.75 µm. The material presented a surface area of 954 and 704 m2/g and a pore volume of 0.321 and 0.286 cm3/g, for Nb-MCM-41 and Nb-MCM-48, respectively. Also, both materials showed a pore size of 2.261 nm. The number of recycles obtained for the CALB enzyme immobilized in Nb-MCM-41 and Nb-MCM-48 was 26 recycles with a residual activity of 49.62% and 16 recycles with a residual activity of 53.01%, respectively. For both materials, enzymatic activity remained stable for 5 months of storage at room temperature and refrigeration. The supports were able to catalyze the esterification reaction at 40, 60, and 80 °C, showing industrial application in reactions that require high temperatures. This methodology allows the preparation of new highly active and selective enzyme catalysts using niobium and [C14MI]Cl. Also, the new materials can provide greater viability in processes, ensuring a longer service life of catalysts. Graphical abstract.

Structure-properties relationship in the hydronium-containing pyrochlores (H3O)1+pSb1+pTe1-pO6 with catalytic activity in the fructose dehydration reaction.

A series of defect pyrochlores of the composition (H3O)1+pSb1+pTe1-pO6 have been prepared by ion exchange from K-containing pyrochlores K1+pSb1+pTe1-pO6 in sulfuric acid at 280 °C for 24 h. The structural characterization of the hydronium-containing pyrochlores, including the location of the H3O+ units within the three-dimensional framework, was possible from neutron powder diffraction data in undeuterated samples. The crystal structure for all the compounds is defined in the Fd3[combining macron]m space group, and consists of a covalent framework of SbVO6 and TeVIO6 octahedra distributed at random and connected by their vertices with (Sb,Te)-O1-(Sb,Te) angles close to 136°, conforming to large cages where the hydronium species are located off-center. The absence of K+ ions in the ion-exchanged pyrochlores was confirmed by inductively coupled plasma optical emission spectroscopy and scanning electron microscopy coupled with energy dispersive X-ray spectroscopy. The shape and size of the hydronium units evolve along with the series, becoming more compact as the framework covalence and Lewis-basicity decrease upon Sb enrichment of the structure (for greater p values). The amount and lability of the H3O+ species also increase throughout the series, as wanted: a straightforward correlation of the catalytic activity in the fructose dehydration reaction to 5-hydroxymethylfurfural has been observed, reaching conversion rates up to 88.5% of concentrated fructose solution for the p = 0.25 catalyst. Moreover, a pseudo-first-order kinetic mechanism was simulated, and the kinetic constants obtained from diluted and concentrated enhanced reaction systems were determined and compared.

In vivo evaluation of interactions between biphasic calcium phosphate (BCP)-niobium pentoxide (Nb2O5) nanocomposite and tissues using a rat critical-size calvarial defect model.

Natural or synthetic biomaterials are increasingly being used to support bone tissue repair or substitution. The combination of natural calcium phosphates with biocompatible alloys is an important route towards the development of new biomaterials with bioperformance and mechanical responses to mimic those of human bones. This article evaluated the structural, physical, mechanical and biological properties of a new mechanical improved nanocomposite elaborated by association of fish biphasic calcium phosphate (BCP) and niobium pentoxide (Nb2O5). The nanocomposite (Nb-BCP) and the pure BCP, used as a positive control, were obtained by powder metallurgy. The density, porosity and microhardness were measured. The structural analysis was determined by X-ray diffraction (XRD) and the biological properties were studied in histological sections of critical size calvaria defects in rats, 7, 15, 30, 45 and 60 days after implantation of disks of both materials. Morphological description was made after scanning electron microscopy (SEM) and optical microscopy analysis. After sintering, the Nb-BCP nanocomposite presented four crystalline phases: 34.36% calcium niobate (CaNb2O6), 21.68% phosphorus niobium oxide (PNb9O25), 42.55% ß-tricalcium phosphate (Ca3(PO4)2) and 1.31% of niobium pentoxide (Nb2O5) and exhibited increases of 17% in density, 66% in Vickers microhardness and 180% in compressive strength compared to pure BCP. In vivo study, showed biocompatibility, bioactivity and osteoconductivity similar to pure BCP. SEM showed the formation of globular accretions over the implanted nanocomposites, representing one of the stages of bone mineralization. In conclusion, the BCP and Nb2O5 formed a nanocomposite exhibiting characteristics that are desirable for a biomaterial, such as bioperformance, higher ß-TCP percentage and improved physical and mechanical properties compared to pure BCP. These characteristics demonstrate the promise of this material for supporting bone regeneration.

Effect of ytterbium amount on LaNbO4:Tm3+,Yb3+ nanoparticles for bio-labelling applications.

PURPOSE: This work investigates how Yb3+ concentration affects the luminescent properties of LaNbO4 nanoparticles for medical imaging applications. Due to the highly transparent optical window for organic tissues in the near infrared region (650-1000 nm), upconversion fluorescence allows near infrared wavelengths to penetrate deeply into tissues, which is useful in biomedical areas such as biodetection, activated phototherapy, and screening. MATERIALS/METHOD: Upconversion nanoparticles based on LaNbO4 doped with Tm3+ and Yb3+ were prepared by the one-step industrial process called Spray Pyrolysis. Samples with different Tm3+:Yb3+ molar ratios (1:4, 1:8 and 1:16) were obtained. RESULTS: The X-ray powder diffractograms of all the samples displayed the typical peaks of a crystalline material (tetragonal phase). Emission bands emerged in the blue, red, and near infrared regions, and they corresponded to the Tm3+1G4 → 3H6 (475 nm), 1G4 → 3F4 (650 nm), 3F2,3 â†’ 3H6 (690 nm), and 3H4 → 3H6 (803 nm) transitions, which indicated a two-photon absorption process. As for bio-labelling application, the results indicated that Yb3+ concentration was directly related to signal intensity. CONCLUSIONS: The intensity of positive conversion emissions depends directly on Yb3+ concentration. The bio-labelling tests pointed to the potential application of these materials. The sample containing the highest amount of Yb3+ provided better results and was easier to detect than the standard sample.

High Sensitive Biosensors Based on the Coupling Between Surface Plasmon Polaritons on Titanium Nitride and a Planar Waveguide Mode.

High sensitivity biosensors based on the coupling of surface plasmon polaritons on titanium nitride (TiN) and a planar waveguide mode were built; they were proved by sensing three different media: air, water and dried egg white; sensors described here could be useful for sensing materials with a refractive index between 1.0 and 1.6; in particular, materials of biological interest with a refractive index in the range 1.3-1.6, like those containing biotin and/or streptavidin. They were built by depositing Nb2O5/SiO2/TiN multilayer structures on the flat surface of D-shaped sapphire prisms by using the dc magnetron sputtering technique. Attenuated total reflection (ATR) experiments in the Kretschmann configuration were accomplished for the air/TiN/Prism and S/Nb2O5/SiO2/TiN/Prism structures, S being the sample or sensing medium. ATR spectra for plasmons at the TiN/air interface showed a broad absorption band for angles of incidence between 36 and 85°, with full width at half maximum (FWHM) of approximately 40°. For the S/Nb2O5/SiO2/TiN/Prism structures, ATR spectra showed a sharp reflectivity peak, within the broad plasmonic absorption band, which was associated with Fano resonances. The angular position and FWHM of the Fano resonances strongly depend on the refractive index of the sensing medium. ATR spectra were fitted by using the transfer-matrix method. Additionally, we found that angular sensitivity and figure of merit increase with increasing the refractive index of the sensing medium.

Performance of Nb/BDD material for the electrochemical advanced oxidation of prednisone in different water matrix.

Glucocorticoids are widely used to treat a variety of diseases. Consequently, these compounds have been found in water and wastewater matrix. Despite studies have proven its toxicity, just a few works investigate techniques to degrade and mineralize them. To solve this issue, this work presents the degradation and mineralization of prednisone (PRED) by electrochemical advanced oxidation (EAO) using a boron-doped diamond supported on niobium (Nb/BDD) anode in synthetic and real wastewater. Cyclic voltammetry (CV) was performed to investigate the PRED oxidation mechanisms. CV suggest that PRED will be oxidized via HO• and other oxidants generated from the ions present in the liquid matrix (S2O82-, SO4•-, HClO, ClO- etc.). Different EAO conditions as initial pH (3, 7 and 11) and applied current densities (5, 10 and 20 mA cm-2) were evaluated. The best result was obtained at alkaline pH (11) and a current density of 20 mA cm-2, achieving 78% of degradation and 42% of mineralization. Using the best conditions, the EAO was applied as a polishing treatment stage to remove PRED from a biological pre-treated municipal wastewater spiked with PRED. The results indicate that EAO applied in the real matrix provides better results than the synthetic solution, probably associated with the presence of ions that can be electrochemically converted into oxidant species, resulting in higher kinetic constant, mineralization current efficiency and lower energetic consumption. Therefore, the EAO process without the addition of chemicals has proven to be an effective alternative as a tertiary treatment of municipal wastewater contaminated with PRED.

In vitro and in vivo osteogenic potential of niobium-doped 45S5 bioactive glass: A comparative study.

In vitro and in vivo experiments were undertaken to evaluate the solubility, apatite-forming ability, cytocompatibility, osteostimulation, and osteoinduction for a series of Nb-containing bioactive glass (BGNb) derived from composition of 45S5 Bioglass. Inductively coupled plasma optical emission spectrometry (ICP-OES) revealed that the rate at which Na, Ca, Si, P, and Nb species are leached from the glass decrease with the increasing concentration of the niobium oxide. The formation of apatite as a function of time in simulated body fluid was monitored by 31P Magic Angle Spinning (MAS) Nuclear magnetic resonance spectroscopy. Results showed that the bioactive glasses: Bioglass 45S5 (BG45S5) and 1 mol%-Nb-containing-bioactive glass (BGSN1) were able to grow apatite layer on their surfaces within 3 h, while glasses with higher concentrations of Nb2 O5 (2.5 and 5 mol%) took at least 12 h. Nb-substituted glasses were shown to be compatible with bone marrow-derived mesenchymal stem cells (BMMSCs). Moreover, the bioactive glass with 1 mol% Nb2 O5 significantly enhanced cell proliferation after 4 days of treatment. Concentrations of 1 and 2.5 mol% Nb2 O5 stimulated osteogenic differentiation of BMMSCs after 21 days of treatment. For the in vivo experiments, trial glass rods were implanted into circular defects in rat tibia in order to evaluate their osteoconductivity and osteostimulation. Two morphometric parameters were analyzed: (a) thickness of new-formed bone layer and (b) area of new-formed subperiostal bone. Results showed that BGNb bioactive glass is osteoconductive and osteostimulative. Therefore, these results indicate that Nb-substituted glass is suitable for biomedical applications.

Fabrication of electrospun poly(lactic acid) nanoporous membrane loaded with niobium pentoxide nanoparticles as a potential scaffold for biomaterial applications.

Tissue engineering aims to regenerate and restore damaged human organs and tissues using scaffolds that can mimic the native tissues. The requirement for modern and efficient biomaterials that are capable of accelerating the healing process has been considerably increased. In this work, a novel electrospun poly(lactic acid) (PLA) nanoporous membrane incorporated with niobium pentoxide nanoparticles (Nb2 O5 ) for biomaterial applications was developed. Nb2 O5 nanoparticles were obtained by microwave-assisted hydrothermal synthesis, and different concentrations (0, 1, 3, and 5% wt/wt) were tested. Chemical, morphological, mechanical, and biological properties of membranes were evaluated. Cell viability results demonstrated that the membranes presented nontoxic effects. The incorporation of Nb2 O5 improved cell proliferation without impairing the wettability, porosity, and mechanical properties of membranes. Membranes containing Nb2 O5 nanoparticles presented biocompatible properties with suitable porosity, which facilitated cell attachment and proliferation while allowing diffusion of oxygen and nutrients. This study has demonstrated that Nb2 O5 nanoparticle-loaded electrospun PLA nanoporous membranes are potential candidates for drug delivery and wound dressing applications.

Preparation, structural, microstructural, mechanical, and cytotoxic characterization of Ti-15Nb alloy for biomedical applications.

Titanium alloys are widely used in the biomedical field due to their excellent resistance to corrosion, high mechanical strength/density ratio, low elastic modulus, and good biocompatibility. Niobium is a ß-stabilizer element that has the potential to decrease elastic modulus and possesses excellent corrosion resistance. In this article, Ti-15Nb alloy was prepared via arc-melting, with the aim of using it in biomedical applications to replace implants that fail due to mechanical incompatibility with human bone. This Ti-15Nb alloy was structurally, chemically, and microstructurally characterized. Its mechanical properties were analyzed via Vickers microhardness and elastic modulus measurements. The cytotoxicity of the alloy was evaluated via direct and indirect MTT tests. In the direct MTT test, the cells were grown on alloy and in the indirect test, Ti-15Nb alloy extracts were prepared (1 g/1 mL at 310 K for 48 hours). The results of chemical composition showed that the alloy produced has good quality and low content of gaseous impurities, such as oxygen and nitrogen. The obtained results for structure and microstructure indicated the presence of the martensite α' phase. The microhardness of the Ti-15Nb alloy is superior to that of cp-Ti due to solid solution hardening, and the alloy has a better elastic modulus as compared to pure titanium. Cytotoxic effects were not observed. The Ti-15Nb alloy shows good results of mechanical properties and does not show cytotoxic effects. In addition, morphological variations were not found in the cells and good cell adhesion in all the studied conditions was observed. In general, the alloy proposed in this article has satisfactory characteristics as a biomedical material.

Osteogenic differentiation of bone marrow-derived mesenchymal stem cells on anodized niobium surface.

Currently, titanium and its alloys are the most used materials for biomedical applications. However, because of the high costs of these metals, new materials, such as niobium, have been researched. Niobium appears as a promising material due to its biocompatibility, and excellent corrosion resistance. In this work, anodized niobium samples were produced and characterized. Their capacity to support the osteogenic differentiation of bone marrow-derived mesenchymal stem cells (BM-MSCs) was also tested. The anodized niobium samples were characterized by SEM, profilometry, XPS, and wettability. BM-MSCs were cultured on the samples during 14 days, and tested for cell adhesion, metabolic activity, alkaline phosphatase activity, and mineralization. Results demonstrated that anodization promotes the formation of a hydrophilic nanoporous oxide layer on the Nb surface, which can contribute to the increase in the metabolic activity, and in osteogenic differentiation of BM-MSCs, as well as to the extracellular matrix mineralization.

Proteome analysis of the salivary pellicle formed on titanium alloys containing niobium and zirconium.

The chemical composition of biomaterials can drive their biological responses; therefore, this in vitro study aimed to evaluate the proteomic profile of the salivary pellicle formed on titanium (Ti) alloys containing niobium (Nb) and zirconium (Zr). The experimental groups consisted of Ti35NbxZr (x = 5 and 10 wt%) alloys, and commercially pure titanium (cpTi); titanium aluminium vanadium (Ti6Al4V) alloys were used as controls. The physical and chemical characteristics of the Ti materials were analysed. The proteomic profile was evaluated by liquid chromatography coupled with tandem mass spectrometry. Bacterial adhesion (2 h) of mixed species (Streptococcus sanguinis and Actinomyces naeslundii) was investigated as colony-forming units (n = 6). This paper reports the finding that salivary pellicle composition can be modulated by the composition of the Ti material. The Ti35NbxZr group showed a significant ability to adsorb proteins from saliva, which can favour interactions with cells and compatibility with the body.

Electrooxidation Using Nb/BDD as Post-Treatment of a Reverse Osmosis Concentrate in the Petrochemical Industry.

This work evaluated the performance of an electrochemical oxidation process (EOP), using boron-doped diamond on niobium substrate (Nb/BDD), for the treatment of a reverse osmosis concentrate (ROC) produced from a petrochemical wastewater. The effects of applied current density (5, 10, or 20 mA·cm-2) and oxidation time (0 to 5 h) were evaluated following changes in chemical oxygen demand (COD) and total organic carbon (TOC). Current efficiency and specific energy consumption were also evaluated. Besides, the organic byproducts generated by EOP were analyzed by gas chromatography coupled to mass spectrometry (GC⁻MS). The results show that current densities and oxidation time lead to a COD and TOC reduction. For the 20 mA·cm-2, changes in the kinetic regime were found at 3 h and associated to the oxidation of inorganic ions by chlorinated species. After 3 h, the oxidants act in the organic oxidation, leading to a TOC removal of 71%. Although, due to the evolution of parallel reactions (O2, H2O2, and O3), the specific energy consumption also increased, the resulting consumption value of 66.5 kW·h·kg-1 of COD is considered a low energy requirement representing lower treatment costs. These results encourage the applicability of EOP equipped with Nb/BDD as a treatment process for the ROC.

The antibacterial effect of potassium-sodium niobate ceramics based on controlling piezoelectric properties.

The implant infection is one of the most serious postsurgical complications of medical device implantation. Therefore, the development of biocompatible materials with improved antibacterial properties is of great importance. It might be a new insight to apply the intrinsic electrical properties of biomaterials to solve this problem. Here, potassium-sodium niobate piezoceramics (K0.5Na0.5NbO3, KNN) with different piezoelectric constants were prepared, and the microstructures and piezoelectric properties of these piezoceramics were evaluated. Moreover, the antibacterial effect and biocompatibility of these piezoceramics were assayed. Results showed that these piezoceramics were able to decrease the colonies of bacteria staphylococcus aureus (S. aureus), favor the rat bone marrow mesenchymal stem cells (rBMSCs) proliferation and promote the cell adhesion and spreading. The above effects were found closely related to the surface positive charges of the piezoceramics, and the sample bearing the most positive charges on its surface (sample 80KNN) had the best performance in both antibacterial effect and biocompatibility. Based on our work, it is feasible to develop biocompatible antibacterial materials by controlling piezoelectric properties.