Multi-physical field simulation calculation and analysis of simulated high-level waste liquid spray calcination.

Aiming at the independent research and development of a simulated high-level waste liquid spray calcination transformation treatment test device, a three-dimensional multi-physical field model of spray calcination was established by means of finite element analysis method. In this paper, the simulated high-level waste liquid is a mixed solution of nitrate solution and sucrose. The main chemical components of nitrate dissolution are HNO3 and NaNO3. The process of evaporation and calcination of high-level waste liquid to form oxides is also called the pretreatment of high-level waste liquid or the conversion of high-level waste liquid. In this experiment, the atomized droplets sprayed at high speed are evaporated, dried and calcined in turn in the calciner to obtain the calcined product. The distribution law of temperature flow field and chemical reaction state and results inside the test device were revealed by simulation calculation. The results show that under the condition of multi-physical field coupling, the chemical reaction temperature has an effect on the yield of the product. The temperature is positively correlated with the product concentration, and the effect of temperature on the yield of NO2 is greater than that of Na2O. At the same time, in this chemical reaction, the concentration of reactants (NaNO3 and HNO3) had a positive correlation with the concentration of main products (NO2 and Na2O). However, the rate of increase in the concentration of the main products (NO2 and Na2O) decreased with the increase of the concentration of the reactants (NaNO3 and HNO3).

Treatment of Plantar Warts with a Nitric-Zinc Complex Solution: A Review of 72 Cases.

BACKGROUND: There are multiple conservative treatment options for plantar warts, but none have proven to be universally effective. Nitric acid is often used empirically by podiatrists in the treatment of plantar warts. A novel medical device or topical solution of nitric-zinc complex solution (NZCS) could potentially offer an effective and safe alternative for the targeted treatment of plantar warts. OBJECTIVE: To observe the rate of complete healing of NZCS in a series of plantar wart cases and to establish the minimum number of product applications and time needed for healing. This will help standardize and protocolize its use. METHODS: A descriptive study was conducted involving 72 patients who exhibited symptoms of plantar warts. These patients underwent chemical treatment using a nitric-zinc complex. RESULTS: The cure rate with NZCS was 59.2%. The average number of NZCS applications was 5.9 ± 3.0 and the mean duration of treatment was 9.4 ± 7.1 weeks. A recurrence rate of 6.7% was observed. CONCLUSIONS: The topical solution of the nitric-zinc complex is an effective treatment for plantar warts, which can be considered a first-line treatment option in the general population.

Microwave-assisted acid treatment for the mineral transformation of chrysotile as an alternative for asbestos waste management.

In this work, the effect of microwave-assisted acid treatments on the morphological and crystallochemical characteristics of chrysotile fibers is investigated. A low concentration of nitric acid (0.2 N) is used to remove Mg2+-species located in the octahedral sheet of its structure, thereby causing a crystallo-chemical change forming a skeleton of non-crystalline amorphous silica. This skeleton maintains an elongated morphology but characterized by rounded -not sharp-edges and porous surfaces whose physical resistance under stress is reduced when compared with the initial fibers of chrysotile, favoring a lower pathogenicity of the fibers. Thus, microwave-assisted acid treatment rise as a low-cost, fast and effective option in avoiding the dangerousness associated with asbestos waste management.

Remarkable enhancement in radio-cesium uptake from acidic feeds into an extraction chromatography resin containing a calix[4]arene-mono-crown-6 ligand.

An extraction chromatography resin, prepared by the impregnation of bis-octyloxy-calix[4]arene-mono-crown-6 (BOCMC)onto an acrylic ester based polymeric support material, gave excellent uptake data for the removal of radio-cesium (Cs-137) from nitric acid feed solutions. The weight distribution coefficient (Kd) value of >300 obtained during the present study at 3 M HNO3 was the highest reported so far while using a calix-crown-6 based extraction chromatographic resin material. Analogous resin reported previously has yielded a Kd value <100 at comparable feed conditions. The sorbed metal ions could be efficiently desorbed with de-ionized water. Kinetic modeling of the uptake data indicated that both the film and the intra-particle diffusion mechanism are simultaneously operating in the sorption of Cs+ion onto the BOCMC resin. The metal ion sorption data were fitted to the sorption isotherm models and did not conform to the chemisorptions of physisorption models and indicated a pi-pi interaction between the benzene rings of the calix-crown-6 ligand and the Cs+ ion. The reusability of the resins was quite satisfactory after 5 cycles and the radiation stability of the resin material was very good upto an absorbed dose of 500 kGy. The results of column studies were quite encouraging with 15 mL (9 bed volumes) as the breakthrough volume while the elution was complete in about 12 bed volumes of de-ionized water.

Separation of gold from irradiated actinide material utilizing a 2- thenoyltrifluoroacetone extraction resin.

Post-detonation nuclear forensics capabilities depend on the ability to rapidly isolate radionuclides to improve measurement quality. In this work an extraction chromatography resin was developed utilizing thenoyltrifluoroacetone and 1-octanol supported on Eichrom prefilter resin. The resin was tested in nitric and hydrochloric acid matrices. In nitric acid the resin was able to extract zirconium, while in hydrochloric acid matrices it was possible to extract iron and gallium. In all acid conditions tested, gold was retained but can be eluted from the column with 10 % thiourea.

Effect of Various Surface Treatments of Zirconia on its Adhesive Properties to Dentin: An In Vitro Study.

AIM: To assess the effectiveness of various surface treatments and adhesives on the bond strength of zirconia-based ceramic to dentin. MATERIALS AND METHODS: Eighty samples of zirconia were subjected to the four-surface treatment protocols (sandblasting, 48% hydrofluoric acid (HF), 48% hydrofluoric acid + 70% nitric acid (HNO3) and no treatment (control) following which the samples from each group were subdivided into two subgroups (n = 10) based on the resin cement employed for cementation (RelyX U200 and G-Cem Linkforce). The bonded specimens were subjected to shear stress to measure the bond strength using Universal testing machine. To test the difference in bond strength among the eight study groups, the Kruskal-Wallis ANOVA test was applied and for comparison between cements in each group, Mann-Whitney U test was applied. RESULTS: The highest bond strength values were observed for 48% HF group cemented with G-Cem Linkforce resin cement (16.220 ± 1.574) and lowest for control group-RelyX (4.954 ± 0.972). G-Cem cement showed higher bond strength than RelyX for all surface treatments except 48% HF + 70% nitric acid. CONCLUSION: It can be inferred that 48% HF can etch zirconia and generate a porous structure that proves to be beneficial for bonding. CLINICAL SIGNIFICANCE: The increasing demand for esthetics has led to the replacement of metal-ceramic materials with zirconia-based ceramics. However, the chemical inertness of zirconia to various conventional surface treating agents has continuously challenged researchers to discover a new surface treatment protocol that could enhance the bond strength of zirconia. How to cite this article: Yenamandra MS, Joseph A, Singh P, et al. Effect of Various Surface Treatments of Zirconia on its Adhesive Properties to Dentin: An In Vitro Study. J Contemp Dent Pract 2024;25(3):226-230.

Comparing nitric acid treatment and microwave digestion for efficiency of metal extraction from bioprocess samples.

Metal ions may act as enzyme cofactors and influence the kinetics of biochemical reactions that may also influence the biological production of therapeutic proteins and quality attributes such as glycosylation. Because sample preparation is a significant step in the reliable analysis of metals, we compared two sample preparation procedures for metal analysis of bioreactor culture media samples by ICP-MS: (i) samples were diluted in 2 % nitric acid (treatment with nitric acid, TNA); and (ii) samples were mixed with equal volume of 5 % nitric acid and closed vessel digestion was performed in a microwave (closed vessel digestion, CVD). In the comparison of extraction efficiencies between TNA and CVD procedures, CVD showed better extraction for Ca and Cu among bulk metals (∼30 %) and for Ni among the trace metals (∼65 %) for the bioreactor broth supernatant samples. For the cell pellet samples, the CVD procedure was found to be better for extraction of Fe (∼65 % more) among bulk metals, Zn (∼20 % more) among minor metals and Co (∼60 % more) and Ni (∼45 % more) among trace metals. Differences between the two procedures were less than 10 % and TNA was better for all other metals quantified from both supernatant samples and cell pellet samples. The current study helps bring more clarity to the methodology on comprehensive metal analysis to monitor and maintain trace metal content for biologics production.

A comparative study on the uptake of lanthanides from acidic feeds using extraction chromatography resins containing N,N,N',N'-tetra-n-alkyl diglycolamides with varying alkyl chain lengths in an ionic liquid.

A comparative study on the uptake of several rare earth element (REE) ions viz. La(III), Ce(III), Pr(III), Nd(III), Sm(III), Gd(III) and Dy(III) was carried out from nitric acid feeds using four extraction chromatography resins which contained the diglycolamide (DGA) ligands, N,N,N',N'-tetra-n-alkyldiglycolamide with n-pentyl (TPDGA), n-hexyl (THDGA), n-octyl (TODGA) and n-decyl (TDDGA) groups taken in a room temperature ionic liquid (C4mim·NTf2). The uptake of the lanthanides followed the trend: La(III) < Ce(III) < Pr(III) < Nd(III) < Sm(III) < Gd(III) < Dy(III), which is similar to their ionic potential values and the uptake trend of the resins was TPDGA > THDGA > TODGA > TDDGA. The uptake of the metal ions was very high (>104 g/mL) for all the lanthanide ions and was found to increase with increasing nitric acid concentrations. Based on the encouraging batch data, column studies were carried out with all the four extraction chromatography resins with the lanthanide ions used in this work. The column studies were carried out with both individual lanthanide ions and their mixtures. While the loading studies were carried out with 80 mg/L solutions of the metal ions (with respect to each of those) in the mixture of REEs, the elution studies were carried out using a solution of 0.05 M EDTA in 1 M guanidine carbonate. For the column studies involving individual REEs, 550 mg/L solutions were used. The elution profiles appeared to be sharp as >95% elution of the metal ions was accomplished in only 3 mL of the eluent which amounted to only 1.6 bed volumes which is highly impressive. When the studies were carried out with the mixture of the lanthanide ions, the breakthrough of Dy(III) was last while that of La(III) was seen at much lower volumes which was dependent on the nature of the extractant in the resins.

Multielement Determination in Turmeric (Curcuma longa L.) Using Different Digestion Methods.

The antioxidant, anti-inflammatory and antiseptic properties of turmeric (Curcuma longa L.) derive from its rich nutritional composition making it interesting for medicinal uses, besides being used as spice in cooking. To complete the picture on the composition of turmeric, not only the organic compounds need to be known, but also the elemental composition covering essential and potentially toxic elements. The samples were digested in a microwave assisted digestion system using different reagent mixtures. The best digestion mixture was semi-concentrated nitric acid combined with hydrogen peroxide. After optimization of the sample preparation method, the contents of Ag, Al, As, Ba, Be, Bi, Ca, Cd, Co, Cr, Cu, Fe, Ga, K, Li, Mg, Mn, Mo, Na, Ni, Pb, Rb, Se, Sr, Te, Tl, V and Zn in curcuma were determined by inductively coupled plasma atomic emission spectrometry (ICP-AES), as well as by inductively coupled plasma mass spectrometry (ICP-MS). Even if the general composition found is in line with the scarce data in literature, clear differences can be seen between the analyzed samples, considering provenience, production procedures, and harvesting year as potential influencing factors. Whereas all samples contained less As and Pb than regulated by WHO, one limit exceeding was found for Cd.

Radiation stability of two extraction chromatography resin materials containing substituted diglycolamide ligands in an ionic liquid.

The radiation stability of two extraction chromatography resins containing diglycolamide ligands viz. TPDGA (N,N,N',N'-tetra-n-pentyl diglycolamide) and TODGA (N,N,N',N'-tetra-n-octyl diglycolamide) in a room temperature ionic liquid (C4mim.NTf2) was studied by exposing to gamma rays from a 60Co source. The resins were irradiated to varying gamma ray dose up to 1000 kGy where both the dry resins and wet resins (containing a fixed amount nitric acid in contact) were used. The performance assessment of the resins was done by physicochemical characterization as well as uptake studies; both by batch as well as column methods. The physicochemical characterization of the resins was done using FTIR analysis while the surface morphology of the resins was carried out by scanning electron microscopy. The uptake of the metal ions, typically that of Am(III) and Eu(III), representing the trivalent actinides and lanthanides was studied by batch method. The dry resins and those in contact with nitric acid yielded nearly identical results suggesting minimal effect of the radiolytic products of nitric acid on the resin performance. There was negligible change in the Kd values up to an absorbed dose of 300 kGy beyond which there was sharp decrease. However, the Kd values were still quite large even after an absorbed dose of 1000 kGy. The column performance of the irradiated resins was also assessed by the uptake and elution of Eu(III) ion and though loading was affected, the elution behavior was found to have insignificant effect.

A brand new two-phase wet oxidation absorption system for the simultaneous removal of SO2 and NOX from simulated marine exhaust gas.

Marine engine exhaust emissions are increasingly harmful to the natural environment and human health and must be controlled. A self-synthesized amide (BAD, C12H25NO) in the laboratory shows a strong absorption capacity of nitric acid and nitrous acid, which may solve the problem that only using chlorine-based oxidant as an absorbent cannot completely absorb or retain NO2 produced by NO oxidation in previous studies. Based on Multiwfn and VMD (Visual Molecular Dynamics) program calculation, the formation mechanism of hydrogen bonds between BAD with nitric acid and nitrous acid was revealed by electrostatic potential (ESP) analysis and further confirmed by FT-IR (Fourier transform infrared spectroscopy) spectra research. Subsequently, simultaneous removal of SO2 and NOX from simulated flue gas was carried out by using NaClO/BAD as a two-phase composite absorbent, and the maximum removal efficiencies of SO2 and NOX were 98.9% and 86.6%, respectively. The recycling experiments and the engineering experiments showing that NaClO/BAD can solve the problem of absorption of NO2, and it can be a promising composite absorbent in wet desulfurization and denitrification of marine engine exhaust gas in practical applications.

Development of an eco-friendly sample preparation protocol for metal determination in food samples: an oxygen pressurized single reaction chamber using diluted nitric acid.

Many efforts have been recently made to improve the digestion efficiency by using powerful equipment or by using an auxiliary reagent. In this work, an alternative method is reported, which explores a digestion system based on a single reaction chamber (SRC) technology pressurized with O2 for reducing the amount of acid, without impairing the digestion efficiency. Before digestion, the system was pressurized with compressed air (20 bar, 20% O2) while the temperature was evaluated from 180 up to 270 °C. The procedure was also carried out under O2 pressure (20 bar). For each temperature several acid concentrations were evaluated (0.1 to 3 mol L-1 HNO3), being possible to correlate the effectiveness of each acid concentration with temperature. The proposed method was applied to the simultaneous digestion of several organic matrices with variable content of fat, protein, and carbohydrate (whole milk powder, bovine liver, parsley, and linseed). The residual carbon content was lower than 4% (C lower than 200 mg L-1 in digests), showing the high digestion efficiency of the proposed approach. Up to 250 mg of all food matrices were digested using a sub-stoichiometric amount of HNO3 (1 mol L-1 solution), which was only achieved due to the use of O2 as an auxiliary reagent. Barium, Ca, Cu, Fe, K, Mg, Mn, Na, Sr, and Zn were determined by ICP-OES, and the accuracy was better than 95% for standard reference materials of corn bran, whole milk powder, and bovine liver. It is an important feature, being in agreement with green chemistry recommendations because very low amounts of reagents are required for sample digestion, as well as low amounts of residues are generated.

Structure features, selenylation modification, and improved anti-tumor activity of a polysaccharide from Eriobotrya japonica.

A homogeneous polysaccharide, EJP90-1, was isolated from the leaves of E. japonica by hot water extraction in this study. EJP90-1 (7702 Da) was a heteropolysaccharide mainly consisting of →5)-linked-α-L-Araf-(1→, →4)-linked-ß-D-Manp-(1→, →2,4)-linked-α-L-Rhap-(1→, →4)-linked-α-D-Xylp-(1→, →4)-linked-ß-D-Galp-(1→, →2)-linked-ß-D-Galp-(1→, →6)-linked-ß-D-Glcp-(1→, α-D-Glcp-(4→, and t-linked-α-L-Araf. EJP90-1 was found to show moderate anti-tumor activity at the cellular level. In order to improve the anti-tumor activity and the potential applications of EJP90-1, a typical sodium selenite-nitric acid (Na2SeO3-HNO3) modification on EJP90-1 was carried out. X-ray photoelectron spectroscopy (XPS) and energy dispersive spectrometer (EDS) analysis confirmed that Se was successfully introduced into the polymer chain of EJP90-1. The subsequent in vitro cytotoxicity evaluation showed the selenylation modification derivative (EJP90-1-Se) possessed significant antiproliferative activity against cancer cells (HepG2 and A549 cells) through inducing cell apoptosis. The anti-tumor activity of EJP90-1-Se was further confirmed by zebrafish models, which inhibited the proliferation and migration of HepG2 cells and the angiogenesis.

Rapid sulfuric acid-dimethylamine nucleation enhanced by nitric acid in polluted regions.

Recent research [Wang et al., Nature 581, 184-189 (2020)] indicates nitric acid (NA) can participate in sulfuric acid (SA)-ammonia (NH3) nucleation in the clean and cold upper free troposphere, whereas NA exhibits no obvious effects at the boundary layer with relatively high temperatures. Herein, considering that an SA-dimethylamine (DMA) nucleation mechanism was detected in megacities [Yao et al., Science 361, 278-281 (2018)], the roles of NA in SA-DMA nucleation are investigated. Different from SA-NH3 nucleation, we found that NA can enhance SA-DMA-based particle formation rates in the polluted atmospheric boundary layer, such as Beijing in winter, with the enhancement up to 80-fold. Moreover, we found that NA can promote the number concentrations of nucleation clusters (up to 27-fold) and contribute 76% of cluster formation pathways at 280 K. The enhancements on particle formation by NA are critical for particulate pollution in the polluted boundary layer with relatively high NA and DMA concentrations.

Selective uptake of thorium(IV) from nitric acid medium using two extraction chromatographic resins based on diglycolamide-calix[4]arenes: Application to thorium-uranyl separation in an actual sample.

Two novel extraction chromatography resins (ECRs) containing two diglycolamide (DGA) -functionalized calix[4]arenes with n-propyl and isopentyl substituents at the amide nitrogen atom, termed as ECR-1 and ECR-2, respectively, were evaluated for the uptake of Th(IV) from nitric acid feed solutions. While both the resins were having a quite high Th(IV) uptake ability (Kd >3000 at 3 M HNO3), the uptake was relatively lower with the resin containing the isopentyl DGA, which appeared magnified at lower nitric acid concentrations. Kinetic modeling of the sorption data suggested fitting to the pseudo-second order model pointing to a chemical reaction during the uptake of the metal ion. Sorption isotherm studies were carried out showing a good fitting to the Langmuir and D-R isotherm models, suggesting the uptake conforming to monolayer sorption and a chemisorption model. Glass columns with a bed volume of ca. 2.5 mL containing ca. 0.5 g lots of the ECRs were used for studies to assess the possibility of actual applications of the ECRs. Breakthrough profiles obtained with feed containing 0.7 g/L Th(NO3)3 solution resulted in breakthrough volumes of 8 and 5 mL, respectively, for the ECR-1 and ECR-2 resins. Near quantitative elution of the loaded metal ion was possible using a solution of oxalic acid and nitric acid. A method for the separation of Th-234 from natural uranium was demonstrated for the possible application of ECR-1.

In vitro targeting and selective killing of mcf-7 and colo320dm cells by 5-fluorouracil anchored to carboxylated SWCNTs and MWCNTs.

The intention of the present work was to synthesize the f-MWCNT and f-SWCNT terminated with proper functional group, loading of 5-Flurouracil and to perform cytotoxic activity. Functionalization of MWCNTs and SWCNTs was achieved through the acid treatment (H2SO4 + HNO3). 5-flurouracil was loaded into the prepared functionalized CNTs, thereafter; in vitro drug loading capacity and % drug release were calculated. Also the prepared f-CNTs, 5-flurouracil loaded CNTs were distinguished by using SEM, TGA, DSC, X-ray diffraction, Raman and FTIR spectroscopy. MCF-7 and COLO320DM cells were treated with selected concentrations of 5-FU loaded f-MWCNTs and f-SWCNTs to estimate the cytotoxic activity. It was observed that 5-FU loaded f-SWCNTs showed good activity against selected cell lines than others. Moreover, apoptosis percentage was reported to be 84.46 ± 4.3515 and 92.78 ± 2.6549 for 5-FU loaded f-SWCNTs against MCF-7 and COLO320DM cells respectively. It is evident from the results that the prepared drug loaded CNTs have comparable antitumor activity in cancer cell lines.

Cation-Driven Lipopolysaccharide Morphological Changes Impact Heterogeneous Reactions of Nitric Acid with Sea Spray Aerosol Particles.

Lipopolysaccharides (LPS) in sea spray aerosol (SSA) particles have recently been shown to undergo heterogeneous reactions with HNO3 in the atmosphere. Here, we integrate theory and experiment to further investigate how the most abundant sea salt cations, Na+, Mg2+, and Ca2+, impact HNO3 reactions with LPS-containing SSA particles. Aerosol reaction flow tube studies show that heterogeneous reactions of SSA particles with divalent cation (Mg2+ and Ca2+) and LPS signatures were less reactive with HNO3 than those dominated by monovalent cations (Na+). All-atom molecular dynamics simulations of model LPS aggregates suggest that divalent cations cross-link the oligosaccharide chains to increase molecular aggregation and rigidity, which changes the particle phase and morphology, decreases water diffusion, and consequently decreases the reactive uptake of HNO3. This study provides new insight into how complex chemical interactions between ocean-derived salts and biogenic organic species can impact the heterogeneous reactivity of SSA particles.

Highly efficient uptake of neptunium from acidic feeds using two solid phase extraction resins containing diglycolamide-functionalized calix[4]arene ligands.

Two solid phase extraction resins (SPER) were prepared by impregnating solutions of two diglycolamide-functionalized calix[4]arenes in 10% isodecanol in n-dodecane into Chromosorb W, as the stationary phase. While SPER-I contained n-propyl functionalized calix[4]arene, SPER-II contained the calix[4]arene with isopentyl groups at the carboxamide nitrogen atoms. The SPERs were characterized by SEM, TGA, FTIR, etc. and were used for the batch uptake of neptunium(IV) from nitric acid feed solutions. While the uptake of Np(IV) was extremely high with SPER-I (Kd: 47,544 at 3 M nitric acid, ca. 8% extractant loading), SPER-II displayed a significantly lower extraction efficiency (Kd: 13,724 under identical conditions) as indicated by the batch uptake studies. Sorption isotherm studies were carried out which indicated good fitting to the Langmuir model suggesting uptake conforming to monolayer sorption. Fitting to the D-R isotherm model conformed to a chemisorption model. Column studies were also carried out and the elution profiles, obtained with solutions of oxalic acid and nitric acid indicated very sharp peaks suggesting that the column can be used for the separation of Np(IV) from acidic radioactive feeds.

Enhanced crystallinity and thermal properties of cellulose from rice husk using acid hydrolysis treatment.

Cellulose was extracted from rice husk (RH) using an integrated delignification process using alkaline treatment and acid hydrolysis (concentrated HNO3) for lignocellulosic biomass dissolution. Cellulose yield and quality were assessed through analysis of lignocellulosic content, thermogravimetric, functional group, X-ray diffraction, and surface morphology. HNO3 treatment showed an increment (2.01-fold) in the cellulose content and some enhancement in the crystallinity of cellulose (up to 40.8%). A slight increase was observed in thermal properties from 334.6 °C to 339.3 °C. Economic analysis showed chlorine extraction produce higher cellulose recovery (58%) as compared to HNO3 (26.7%) with the total cost of operation using HNO3 was double compared to chlorine extraction. The economic feasibility of HNO3 can be improved using various progress in the pre-treatment process, chemical recycling and cellulose recovery process since adopting it is crucial for environmental sustainability.

Multi-element determination in chocolate bars by microwave-induced plasma optical emission spectrometry.

Macro- and microelement determination in chocolate bars by microwave-induced plasma optical emission spectrometry (MIP OES) was evaluated after microwave-assisted sample digestion. Optimization of the sample digestion was carried out, and the recommended conditions were obtained at a temperature of 190 °C, with a digestion time of 40 min and in a mixture constituted by 2.3 mL of nitric acid, 1.0 mL of hydrogen peroxide and 4.7 mL of water. The method was applied in the analysis of chocolate bars, and the concentration ranges of the elements determined were (in mg kg-1): Ca (653-3096); Cr (<0.6-2.8); Cu (<0.16-19.5); Fe (<1.6-227); Mg (147-2775); K (3554-8573); Mn (<0.03-25.2); Na (45.6-1095); Ni (3.2-10.2); P (1111-22594) and Zn (4.8-33.3). The association of the proposed microwave-assisted acid digestion with the MIP OES technique was adequate for multi-element determination in chocolate bars for routine analysis.