Fabrication and characterization of multi-layered coaxial agar-based electrospun biocomposite mat, novel replacement for transdermal patches.

In the performed study, a novel fabrication of agar-based nanofibers was electrospun in an asymmetric bilayer dressing for biomedical transdermal patches. The optimal parameters for the fabrication of agar-based nanofibers after optimization were a feed rate of 10 µL/min, a 7 cm collector-to-nozzle distance, a 15 kV applied voltage, and a 700-rpm rotating collector speed. Coaxial nanofibers, as a second asymmetric layer, were produced using polyvinyl alcohol (PVA) with cephalexin hydrate, an antibacterial drug, as the core and agar-PCL as the sheath. The morphology of the developed uniaxial and coaxial nanofibrous layers was analysed using a scanning electron microscope and transmission electron microscopy, respectively. For the formation of bilayer asymmetric structures, the agar-PCL uniaxial layer was fabricated over the layer of coaxial PVA and agar-PCL layers for sustained drug release. The agar-based nanofibrous mats exhibited tensile strength of 7 MPa with 40 % elongation failure, 8-fold increased swelling, enhanced wettability (60° contact angle), and a moisture transmission rate of 2174 g/m2/day. The developed coaxial bilayer mats exhibited antimicrobial activity, hemocompatibility, and cytocompatibility. Overall, this novel agar nanofibrous dressing offers promising potential for advanced biomedical applications, particularly as transdermal patches for efficient drug delivery systems.

Multifunctional 58S Bioactive Glass/Silver/Cerium Oxide-Based Biocomposites with Effective Antibacterial, Cytocompatibility, and Mechanical Properties.

58S bioactive glass (BG) has effective biocompatibility and bioresorbable properties for bone tissue engineering; however, it has limitations regarding antibacterial, antioxidant, and mechanical properties. Therefore, we have developed BGAC biocomposites by reinforcing 58S BG with silver and ceria nanoparticles, which showed effective bactericidal properties by forming inhibited zones of 2.13 mm (against Escherichia coli) and 1.96 mm (against Staphylococcus aureus; evidenced by disc diffusion assay) and an increment in the antioxidant properties by 39.9%. Moreover, the elastic modulus, hardness, and fracture toughness were observed to be increased by ∼84.7% (∼51.9 GPa), ∼54.5% (∼3.4 GPa), and ∼160% (∼1.3 MPam1/2), whereas the specific wear rate was decreased by ∼55.2% (∼1.9 × 10-11 m3/Nm). X-ray diffraction, high-resolution transmission electron microscopy, and field emission scanning electron microscopy confirmed the fabrication of biocomposites and the uniform distribution of the nanomaterials in the BG matrix. The addition of silver nanoparticles in the 58S BG matrix (in BGA) increased mechanical properties by composite strengthening and bactericidal properties by damaging the cytoplasmic membrane of bacterial cells. The addition of nanoceria in 58S BG (BGC) increased the antioxidant properties by 44.5% (as evidenced by the 2,2-diphenyl-1-picrylhydrazyl assay). The resazurin reduction assay and MTT assay confirmed the effective cytocompatibility for BGAC biocomposites against mouse embryonic fibroblast cells (NIH3T3) and mouse bone marrow stromal cells. Overall, BGAC resulted in mechanical properties comparable to those of cancellous bone, and its effective antibacterial and cytocompatibility properties make it a good candidate for bone healing.

3D-Printed Multifunctional Ag/CeO2/ZnO Reinforced Hydroxyapatite-Based Scaffolds with Effective Antibacterial and Mechanical Properties.

Conventional three-dimensional (3D)-printed hydroxyapatite (HA)-based constructs have limited utility in bone tissue engineering due to their poor mechanical properties, elevated risk of microbial infection, and limited pore interconnectivity. 3D printing of complex multiple components to fabricate fully interconnected scaffolds is a challenging task; here, in this work, we have developed a procedure for fabrication of printable ink for complex systems containing multinanomaterials, i.e., HAACZ (containing 1 wt % Ag, 4 wt % CeO2, and 6 wt % ZnO) with better shear thinning and shape retention properties. Moreover, 3D-printed HAACZ scaffolds showed a modulus of 143.8 GPa, a hardness of 10.8 GPa, a porosity of 59.6%, effective antibacterial properties, and a fully interconnected pore network to be an ideal construct for bone healing. Macropores with an average size of ∼469 and ∼433 µm within the scaffolds of HA and HAACZ and micropores with an average size of ∼0.6 and ∼0.5 µm within the strut of HA and HAACZ were developed. The distribution of fully interconnected micropores was confirmed using computerized tomography, whereas the distribution of micropores within the strut was visualized using Voronoi tessellation. The water contact angle studies revealed the most suitable hydrophilic range of water contact angles of ∼71.7 and ∼76.6° for HA and HAACZ, respectively. HAACZ scaffolds showed comparable apatite formation and cytocompatibility as that of HA. Antibacterial studies revealed effective antibacterial properties for the HAACZ scaffold as compared to HA. There was a decrease in bacterial cell density for HAACZ from 1 × 105 to 1.2 × 103 cells/mm2 against Gram-negative (Escherichia coli) and from 1.9 × 105 to 5.6 × 103 bacterial cells/mm2 against Gram-positive (Staphylococcus aureus). Overall, the 3D-printed HAACZ scaffold resulted in mechanical properties, comparable to those of the cancellous bone, interconnected macro- and microporosities, and excellent antibacterial properties, which could be utilized for bone healing.

Multi-length scale strengthening and cytocompatibility of ultra high molecular weight polyethylene bio-composites by functionalized carbon nanotube and hydroxyapatite reinforcement.

The mechanical properties, such as hardness and elastic modulus, of ultra-high molecular weight polyethylene (UHMWPE) composites for acetabular cup liner are improved by adding hydroxyapatite (HAp) and carbon nanotubes (CNT). However, the weak adhesion of HAp (H) and CNT (C) with UHMWPE (U) limits the enhancement of mechanical properties. Thus, the surface of these reinforcements is silane-treated to improve the adhesion with polymer via Si-O and C=O bonds, as evidenced from spectroscopy techniques. An increased dispersion and interfacial adhesion of functionalized HAp (fH) and CNT (fC) with the polymer matrix is confirmed by nearly two-fold increased reinforcement fraction (Rf: 0.55) of U-10 wt% fHAp-2 wt.% fCNT (U10fH2fC) in comparison to U-10 wt% HAp-2 wt.% CNT (U10H2C). Additionally, Voronoi Tessellation (VT) on SEM micrographs of U10H2C and U10fH2fC revealed the dispersion of functionalized CNTs in U10fH2fC with a center-to-center distance of 0.076 µm, which is 74% higher for unfunctionalized CNT in U10H2C. The multilength scale strengthening of the UHMWPE matrix is confirmed from atomic level modification via functionalization of fillers which effectively adhered to the polymer chain on a micro-scale level. A uniform distribution of CNTs rendered increased crystallinity (+28%) of U10fH2fC, which in turn resulted in significant improvement in bulk mechanical properties (18%, 49%, and 12% increased hardness (148.1 MPa), elastic modulus (3.51 GPa) and tensile elastic modulus (219.8 MPa), respectively) in comparison to that of U10H2C. Functionalized-HAp/CNT reinforced UHMWPE composites maintained its cytocompatibility in the MTT test and fluorescence microscopy, affirming their potential employment as acetabular cup liners for hip joint arthroplasty.

Contact stress and sliding wear damage tolerance of hydroxyapatite and carbon nanotube reinforced polyethylene cup liner against zirconia femoral head.

A finite element modeling (FEM) approach is carried out to estimate the contact stresses such as von-Mises and shear stress on the acetabular cup liner, made up of ultra-high molecular weight polyethylene (UHMWPE)-hydroxyapatite (HAp)-carbon nanotubes (CNT) based composites. The highlights of this work include the effects of liners' material (UHMWPE-HAp-CNT composites), radial clearance (0.05 to 1 mm), and liners' wall thickness (3 to 8 mm) on contact stresses. The thick liner (thickness: 8 mm) with conformal geometry (radial clearance 0.05 mm) produced the lowest contact stresses (von-Mises: 13.8-17.5 MPa and shear stress: 2.3-3.3 MPa). In contrast, the thin liner (thickness: 3 mm) with higher radial clearance (1 mm) showed the highest von-Mises stress (78.6-131.0 MPa) and shear stress (17.0-23.3 MPa). According to ISO 7206-1, nearly 6-7 times reduced contact stresses were observed because of the wider articulating contact area provided by thick cup liner and its conformity with respect to the femoral head. The UHMWPE-2 wt % CNT composite (UC) showed low von-Mises stress (16.1 MPa) and lowest shear stress (2.3 MPa); thus, it is the most damage tolerant material (wear rate: 2.6 × 10-7 mm3/Nm). The excellent mechanical properties such as hardness (165 MPa), elastic modulus (2.28 GPa), and tensile strength (36.7 MPa) are reasoned to elicit an increased sliding-wear resistance of UC. Thus, CNT-based UHMWPE composite can be the potential acetabular cup liner with a thickness of 8 mm and clearance of 0.05 mm without plastic deformation.

Multifunctional Hydroxyapatite Composites for Orthopedic Applications: A Review.

Being a bioactive material, hydroxyapatite (HAp) is regarded as one of the most attractive ceramic biomaterials for bone and hard-tissue replacement and regeneration. Despite its substantial biocompatibility, osteoconductivity, and compositional similarity to that of bone, the employment of HAp is still limited in orthopedic applications due to its poor mechanical (low fracture toughness and bending strength) and antibacterial properties. These significant challenges lead to the notion of developing novel HAp-based composites via different fabrication routes. HAp, when efficaciously combined with functionally graded materials and antibacterial agents, like Ag, ZnO, Co, etc., form composites that render remarkable crack resistance and toughening, as well as enhance its bactericidal efficacy. The addition of different materials and a fabrication method, like 3D printing, greatly influence the porosity of the structure and, in turn, control cell adhesion, thereby enabling biological fixation of the material. This article encompasses an elaborate discussion on different multifunctional HAp composites developed for orthopedic applications with particular emphasis on the incorporation of functionally graded materials and antibacterial agents. The influence of 3D printing on the fabrication of HAp-based scaffolds, and the different in vitro and in vivo studies conducted on these, have all been included here. Furthermore, the present review not only provides insights and broad understanding by elucidating recent advancements toward 4D printing but also directs the reader to future research directions in design and application of HAp-based composite coatings and scaffolds.

The analysis of charge transport mechanism in mixed ionic electronic conductor composite of Sr2TiCoO6double perovskite with yttria stabilized zirconia.

In this investigation, the ionic conduction mechanism in mixed ionic electronic conductors composites of Sr2TiCoO6/YSZ has been studied with the help of universal dynamic response. 3 mol% and 8 mol% yttria stabilized ZrO2have been mixed with Sr2TiCoO6(STC) double perovskite in 1:1 ratio to prepare STC/3YSZ and STC/8YSZ composites via solid-state reaction route. AC Impedance spectroscopy has been carried out to examine the charge transport mechanism, which has been modeled using the microstructural networks of resistors and capacitors. Grain boundaries are more resistive and capacitive compared to the bulk. Modulus spectroscopy analysis demonstrates the non-Debye character of conductivity relaxation with frequency. Complex frequency-dependent AC conductivity is found to obey Almond West power law and reveals that ion migration occurs through the correlated hopping mechanism. Further, the DC conductivity and relaxation time have been found to follow the Barton Nakajima and Namikawa relation, which is correlated with AC to DC conduction. The time-temperature superposition principle has been used to explain the conductivity scaling in the intermediate frequency range. At low temperatures, the ions are localized in the asymmetric potential well, while at high temperatures, hopping behavior starts dominating. Further Kramers-Kronig transformation connects the dielectric strength with conductivity relaxation and verifies the impedance data.

Adhesin Protein Interaction of Staphylococcus Aureus Bacteria with Various Biomaterial Surfaces.

The primary stage of adhesion during implant infection is dominated by interactions of the surface proteins of the bacteria with the substrate atoms. In the current work, molecular dynamics (MD) simulations have been utilized to investigate the mechanics of the associated adhesion forces of bacteria on different surfaces. The unfolding of these adhesion proteins is investigated in order to map these events to earlier experiments on bacterial de-adhesion (using single cell force spectroscopy) with real-life substrates (i.e., ultrahigh molecular weight polyethylene, hydroxyapatite, Ti alloy, and stainless steel). The adhesion of Staphylococcus aureus adhesin (i.e., SpA) is observed by altering their orientation on the silica substrate through MD simulations, followed by capturing unfolding events of three adhesins (SpA, ClfA, and SraP) of variable lengths possessing different secondary structures. The output long-range and short-range interaction forces and consequent visualization of changes in the secondary structure of protein segments are presented during the de-adhesion process. Simulation results are correlated with extracted short-range forces (using Poisson regression) from real-life bacterial de-adhesion experiments. Insights into such protein-substrate interactions may allow for engineering of biomaterials and designing of nonbiofouling surfaces.

Triggered Nanoexplosions of Pd Hollow Spheres.

Gas filled Pd nanocontainers can serve as model nanochambers for reaction and phase equilibria studies. In the current study, palladium hollow spheres (PdHS) filled with oxygen are brought in intimate contact with hydrogen filled PdHS at room temperature (with internal pressure in both the spheres at 20 bar). The molecular hydrogen gets chemisorbed in the Pd shell and further diffuses into the oxygen filled sphere. The rapid reaction of hydrogen with oxygen in the inner wall of the oxygen filled sphere leads to a nanoexplosion, with the formation of water. This explosion results in either the complete breakage of the nanoshell or the formation of connected shells via the rupture of the internal wall connecting the shells. Transmission electron microscopy and Raman spectroscopy have been used to establish the sequence of processes. Further, the water in the nanochambers is cooled below sub-zero temperature to crystallize ice. This phenomenon is observed for the first time at room temperature.

Crystal Chemistry and Antibacterial Properties of Cupriferous Hydroxyapatite.

Copper-doped hydroxyapatite (HA) of nominal composition Ca10(PO4)6[Cux(OH)2-2xOx] (0.0 ≤ x ≤ 0.8) was prepared by solid-state and wet chemical processing to explore the impact of the synthesis route and mode of crystal chemical incorporation of copper on the antibacterial efficacy against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) strains. Apatites prepared by solid-state reaction showed unit cell volume dilation from 527.17 Å3 for copper-free HA to 533.31 Å3 for material of the putative composition Ca10(PO4)6[Cu0.8(OH)0.4O0.8] consistent with Cu+ insertion into the [001] hydroxyapatite channel. This was less pronounced (528.30 Å3 to 529.3 Å3) in the corresponding wet chemical synthesised products, suggesting less complete Cu tunnel incorporation and partial tenancy of Cu in place of calcium. X-ray absorption spectroscopy suggests fast quenching is necessary to prevent oxidation of Cu+ to Cu2+. Raman spectroscopy revealed an absorption band at 630 cm-1 characteristic of symmetric O-Cu+-O units tenanted in the apatite channel while solid-state 31P magic-angle-spinning nuclear magnetic resonance (MAS NMR) supported a vacancy-Cu+ substitution model within the apatite channel. The copper doping strategy increases antibacterial efficiency by 25% to 55% compared to undoped HA, with the finer particle sizes and greater specific surface areas of the wet chemical material demonstrating superior efficacy.

Enhanced Tribological and Bacterial Resistance of Carbon Nanotube with Ceria- and Silver-Incorporated Hydroxyapatite Biocoating.

Pertaining to real-life applications (by scaling up) of hydroxyapatite (HA)-based materials, herein is a study illustrating the role of carbon nanotube (CNT) reinforcement with ceria (CeO2) and silver (Ag) in HA on titanium alloy (TiAl6V4) substrate, utilizing the plasma-spraying processing technique, is presented. When compared with pure HA coating enhanced hardness (from 2.5 to 5.8 GPa), elastic modulus (from 110 to 171 GPa), and fracture toughness (from 0.7 to 2.2 MPa·m1/2) elicited a reduced wear rate from 55.3 × 10-5 mm³·N-1·m-1 to 2.1 × 10-5 mm³·N-1·m-1 in HA-CNT-CeO2-Ag. Besides, an order of magnitude lower Archard's wear constant and a 41% decreased shear stress by for HA-CNT-CeO2-Ag coating depicted the effect of higher hardness and modulus of a material to control its wear phenomenon. Antibacterial property of 46% (bactericidal) is ascribed to Ag in addition to CNT-CeO2 in HA. Nonetheless, the composite coating also portrayed exaggerated L929 fibroblast cell growth (4.8 times more than HA), which was visualized as flat and elongated cells with multiple filopodial protrusions. Hence, synthesis of a material with enhanced mechanical integrity resulting in tribological resistance and cytocompatible efficacy was achieved, thereupon making HA-CNT-CeO2-Ag a scalable potent material for real-life load-bearing implantable bio-coating.

Antioxidant and antibacterial hydroxyapatite-based biocomposite for orthopedic applications.

Post-implantation, vicinity acquired oxidative stress and bacterial infections lead to apoptosis with eventual bone-resorption and implant failure, respectively. Thus, in order to combat aforementioned complications, present research aims in utilizing antioxidant ceria (CeO2) and antibacterial silver (Ag) reinforced hydroxyapatite (HA) composite with enhanced mechanical and cytocompatible properties. Highly dense (>90%) spark plasma sintered HA-based composites elicits enhanced elastic modulus (121-133 GPa) in comparison to that of HA. The antioxidant activity is quantified using ceria alone, wherein HA-ceria and HA-ceria-Ag pellets exhibits ~36 and 30% antioxidant activity, respectively, accrediting ceria as a scavenger of reactive oxygen species, which was corroborated with the % Ce3+ change quantified by X-ray photoelectron spectroscopy. The HA-Ag pellet shows antibacterial efficacy of ~61% for E. coli and ~53% for S. aureus, while a reduction of ~59% for E. coli and ~50% for S. aureus is observed for HA-ceria-2.5Ag pellet, affirming Ag reinforcement as an established bactericidal agent. The enhanced hydrophobicity on all the HA-based composites affords a high protein adsorption (24 h incubation). Further, elevated hFOB cell count (~6.7 times for HA-ceria-Ag on day 7) with filopodial extensions (60-150 µm) and matrix-like deposition reflect cell-substrate intimacy. Thus, synergistic antioxidant ceria and antibacterial Ag reinforcement with enhanced mechanical integrity can potentially serve as cytocompatible porous bone scaffolds or bioactive coatings on femoral stems.

The Role of Nanomechanics in Healthcare.

Nanomechanics has played a vital role in pushing our capability to detect, probe, and manipulate the biological species, such as proteins, cells, and tissues, paving way to a deeper knowledge and superior strategies for healthcare. Nanomechanical characterization techniques, such as atomic force microscopy, nanoindentation, nanotribology, optical tweezers, and other hybrid techniques have been utilized to understand the mechanics and kinetics of biospecies. Investigation of the mechanics of cells and tissues has provided critical information about mechanical characteristics of host body environments. This information has been utilized for developing biomimetic materials and structures for tissue engineering and artificial implants. This review summarizes nanomechanical characterization techniques and their potential applications in healthcare research. The principles and examples of label-free detection of cancers and myocardial infarction by nanomechanical cantilevers are discussed. The vital importance of nanomechanics in regenerative medicine is highlighted from the perspective of material selection and design for developing biocompatible scaffolds. This review interconnects the advancements made in fundamental materials science research and biomedical technology, and therefore provides scientific insight that is of common interest to the researchers working in different disciplines of healthcare science and technology.

Role of silver/zinc oxide in affecting de-adhesion strength of Staphylococcus aureus on polymer biocomposites.

A single-cell force spectroscopy is utilized to characterize the dynamics of the transient interaction (0-10s) between alive Staphylococcus aureus and ultra-high molecular weight polyethylene (UHMWPE). Adhesion force of bacteria upon addition of antibacterial additives (i.e. silver (Ag) nanoparticles and zinc oxide (ZnO) micro-rods) has been evaluated. Addition of Ag and ZnO reduces the colony forming units (CFUs) from 93±7 (UHMWPE) to 23±5 (U+3wt.% Ag+3wt.% ZnO) on 10×10mm2 area of sample surface. Presence of ZnO causes increase in the surface free energy from 29.1 (UHMWPE) to 32.3mJ/m2 (UHMWPE+1wt.% ZnO) and 32.3mJ/m2 for U+3wt.% ZnO whereas due to Ag the surface free energy decreased to 28.3mJ/m2 and 28.4mJ/m2 for UHMWPE+1wt.% Ag and U+3wt.% Ag respectively. At a contact time of 10s bacterial adhesion on U+1wt.% Ag+1wt.% ZnO, U+3wt.% Ag and U+3wt.% Ag+3wt.% ZnO showed lowest adhesion forces, ~2.6nN, ~2.9nN and ~3.2N respectively as compared to neat UHMWPE (~4nN) due to a lower surface free energies, but U+1wt.% Ag and U+1wt.% ZnO and U+3wt.% ZnO show higher adhesion force due their higher surface free energy. Ag nanoparticles reduce the live bacteria count whereas ZnO reduces the bacterial retention and combination of both acts synergistically so the count of live bacteria as well as total bacterial density reduced in U-Ag-ZnO composite samples.

Adhesion force of staphylococcus aureus on various biomaterial surfaces.

Staphylococcus comprises of more than half of all pathogens in orthopedic implant infections and they can cause major bone infection which can result in destruction of joint and bone. In the current study, adhesion force of bacteria on the surface of various biomaterial surfaces is measured using atomic force microscope (AFM). Staphylococcus aureus was immobilized on an AFM tipless cantilever as a force probe to measure the adhesion force between bacteria and biomaterials (viz. ultra-high molecular weight poly ethylene (UHMWPE), stainless steel (SS), Ti-6Al-4V alloy, hydroxyapatite (HA)). At the contact time of 10s, UHMWPE shows weak adhesion force (~4nN) whereas SS showed strong adhesion force (~15nN) due to their surface energy and surface roughness. Bacterial retention and viability experiment (3M™ petrifilm test, agar plate) dictates that hydroxyapatite shows the lowest vaibility of bacteria, whereas lowest bacterial retention is observed on UHMWPE surface. Similar results were obtained from live/dead staining test, where HA shows 65% viability, whereas on UHMWPE, SS and Ti-6Al-4V, the bacterial viability is 78%, 94% and 97%, respectively. Lower adhesion forces, constrained pull-off distance (of bacterial) and high antibacterial resistance of bioactive-HA makes it a potential biomaterial for bone-replacement arthroplasty.

Effect of ZnO morphology on affecting bactericidal property of ultra high molecular weight polyethylene biocomposite.

Bacterial infection of implants can be controlled by selective trapping of bacteria, followed with consequent killing by targeted antibacterial agents. Herein, the role of various ZnO morphologies, viz. micro-rods (R), nanoparticles (NP), and micro-disks (D) on antibacterial efficacy of ZnO via release of Zn(2+) and H2O2 is assessed, both as isolated powders and via incorporating them in cytocompatible ultra high molecular weight polyethylene (UHMWPE). Though ZnO is antibacterial, interestingly, all ZnO morphologies elicited a supportive growth of gram-negative bacteria (Escherichia coli) in culture medium (until 28-35 µg/ml). But, all ZnO morphologies did elicit bactericidal effect on gram positive bacteria (Staphylococcus aureus or Staphylococcus epidermidis) both in culture medium (for 0-2.5 µg/ml) or when incorporated (5-20 wt.%) into UHMWPE. The bactericidal mechanisms were quantified for various ZnO morphologies via: (i) H2O2 production, (ii) Zn(2+) release, and (iii) the presence of surface oxygen vacancies. On one hand, where only ZnO(NP) elicited release of H2O2 in the absence of light, maximum Zn(2+) release was elicited by ZnO(D). Interestingly, when ZnO is incorporated as reinforcement (5-20 wt.%), its antibacterial action against E. coli was vividly observed due to selective proliferation of bacteria only on friendly UHMWPE matrix. Hence, luring bacteria on affable UHMWPE surface can be complemented with their targeted killing by ZnO present in composite.

Carbon Nanotube Functionalization Decreases Osteogenic Differentiation in Aluminum Oxide Reinforced Ultrahigh Molecular Weight Polyethylene.

Ultrahigh molecular weight polyethylene (UHMWPE) is one of the most preferred materials as an acetabular cup-liner for bone implant applications. The current work develops a correlation between wettability, protein adsorption with osteogenic differentiation upon reinforcement of functionalized carbon nanotube (f-CNT) and 10 wt % aluminum oxide (Al2O3) in compression molded UHMWPE composites. Phase characterization has confirmed the retention of CNTs after compression molding. The loading of 2 wt % f-CNT in UHMWPE has shown to increase the contact angle (CA, from 88.9° to ∼97.3°), decrease the surface free energy (SFE, 23.20 to ∼20.85 mJ/m2) and elicit enhanced adsorbed protein density (PD, from ∼0.26 to ∼0.32 mg/cm2) in comparison to that of virgin polymer. Similar trend also has observed with 5 and 10 wt % f-CNT reinforcement. Initially, a high density of L929 mouse fibroblast cells is observed for 10 wt % unfunctionalized CNT (u-CNT) loading (48 h of incubation) with high values of dispersion fraction of surface free energy (σd), i.e., 0.967, whereas a decrease in cell density after 48 h is attributed to significant apatite mineralization and low dispersion fraction (σd) of CNT-Al2O3-UHMWPE biocomposites. Interestingly, gene expression studies have corroborated low osteogenic differentiation (i.e., weaker intensity osteopontin and ß-actin) in 2-10 wt % f-CNT reinforced Al2O3-UHMWPE biocomposites in comparison to that of similar wt % reinforcement of u-CNT. Thus, implant material can be engineered, (bulk or surface-modified), possessing osteoanalogous and cytocompatible properties based on f-CNT-Al2O3-reinforced UHMWPE nanocomposites.

Dispersion fraction enhances cellular growth of carbon nanotube and aluminum oxide reinforced ultrahigh molecular weight polyethylene biocomposites.

Ultrahigh molecular weight polyethylene (UHMWPE) is widely used as bone-replacement material for articulating surfaces due to its excellent wear resistance and low coefficient of friction. But, the wear debris, generated during abrasion between mating surfaces, leads to aseptic loosening of implants. Thus, various reinforcing agents are generally utilized, which may alter the surface and biological properties of UHMWPE. In the current work, the cellular response of compression molded UHMWPE upon reinforcement of bioactive multiwalled carbon nanotubes (MWCNTs) and bioinert aluminum oxide (Al2O3) is investigated. The phase retention and stability were observed using X-ray diffraction, Raman spectroscopy and Fourier transform infrared (FTIR) spectroscopy. The reinforcement of MWCNTs and Al2O3 has shown to alter the wettability (from contact angle of ~88°±2° to ~118°±4°) and surface energy (from ~23.20 to ~17.75 mN/m) of composites with respect to UHMWPE, without eliciting any adverse effect on cytocompatibility for the L929 mouse fibroblast cell line. Interestingly, the cellular growth of the L929 mouse fibroblast cell line is observed to be dominated by the dispersion fraction of surface free energy (SFE). After 48 h of incubation period, a decrease in metabolic activity of MWCNT-Al2O3 reinforced composites is attributed to apatite formation that reduces the dispersion fraction of surface energy. The mineralized apatite during incubation was confirmed and quantified by energy dispersive spectroscopy and X-ray diffraction respectively. Thus, the dispersion fraction of surface free energy can be engineered to play an important role in achieving enhanced metabolic activity of the MWCNT-Al2O3 reinforced UHMWPE biopolymer composites.

Synergistic effect of static magnetic field and HA-Fe3O4 magnetic composites on viability of S. aureus and E. coli bacteria.

In addressing the issue of prosthetic infection, this work demonstrated the synergistic effect of the application of static magnetic field (SMF) and ferrimagnetic substrate properties on the bactericidal property in vitro. This aspect was studied using hydroxyapatite (HA)-xFe3 O4 (x=10, 20, and 40 wt.%) substrates, which have different saturation magnetization properties. During bacteria culture experiments, 100 mT SMF was applied to growth medium (with HA-xFe3 O4 substrate) in vitro for 30, 120, and 240 min. A combination of MTT assay, membrane rupture assays, live/dead assay, and fluorescence microscopic analysis showed that the bactericidal effect of SMF increases with the exposure duration as well as increasing Fe3 O4 content in biomaterial substrates. Importantly, the synergistic bactericidal effect was found to be independent of bacterial cell type, as similar qualitative trend is measured with both gram negative Escherichia coli (E. coli) and gram positive Staphylococcus aureus (S. aureus) strains. The reduction in E. coli viability was 83% higher on HA-40 Wt % Fe3 O4 composite after 4 h exposure to SMF as compared to nonexposed control. Interestingly, any statistically significant difference in ROS was not observed in bacterial growth medium after magnetic field exposure, indicating the absence of ROS enhancement due to magnetic field. Overall, this study illustrates significant role being played by magnetic substrate compositions towards bactericidal property than by magnetic field exposure alone.