Evaluation of force systems generated by Memory Titanol® springs with different preactivation bends.

OBJECTIVE: This study evaluated the force system generated by the Memory Titanol® spring (MTS) with different preactivation bends using an orthodontic force tester (OFT). METHODS: Three preactivations were tested using a 0.017 × 0.022-in stainless steel (SS) wire and a 0.018 × 0.025-in NiTi segment, with an activation of 30º in the posterior segment (ß), with 0º (Group 1 [G1]), 45º (Group 2 [G2]), and 60º (Group 3 [G3]) in the anterior segment (α). RESULTS: The molars showed extrusion values of -1.33 N for G1 and -0.78 N for G2, and an intrusion value of 0.33 N for G3. The force in the premolars was intrusive with a variation of 1.34 N for G1 and 0.77 N for G2; and extrusive with a variation of -0.31 N for G3. Regarding the upright moment (Ty) of the molar, a distal moment was observed with values of 53.45 N.mm for G1 and 19.87 N.mm for G2, while G3 presented a mesial moment of -6.23 N.mm. G1, G2, and G3 all exhibited distal premolar moments (Ty) of 3.58, 2.45, and 0.68 N.mm, respectively. CONCLUSIONS: The tested preactivations exerted an extrusive force in G1 and G2 and an intrusive force in G3 during molar vertical movement. The premolar region in G1 and G2 showed intrusive force and distal moment.

Artificial intelligence as a prediction tool for orthognathic surgery assessment.

INTRODUCTION: An ideal orthodontic treatment involves qualitative and quantitative measurements of dental and skeletal components to evaluate patients' discrepancies, such as facial, occlusal, and functional characteristics. Deciding between orthodontics and orthognathic surgery remains challenging, especially in borderline patients. Advances in technology are aiding clinical decisions in orthodontics. The increasing availability of data and the era of big data enable the use of artificial intelligence to guide clinicians' diagnoses. This study aims to test the capacity of different machine learning (ML) models to predict whether orthognathic surgery or orthodontics treatment is required, using soft and hard tissue cephalometric values. METHODS: A total of 920 lateral radiographs from patients previously treated with either conventional orthodontics or in combination with orthognathic surgery were used, comprising n = 558 Class II and n = 362 Class III patients, respectively. Thirty-two measures were obtained from each cephalogram at the initial appointment. The subjects were randomly divided into training (n = 552), validation (n = 183), and test (n = 185) datasets, both as an entire sample and divided into Class II and Class III sub-groups. The extracted data were evaluated using 10 machine learning models and by a four-expert panel consisting of orthodontists (n = 2) and surgeons (n = 2). RESULTS: The combined prediction of 10 models showed top-ranked performance in the testing dataset for accuracy, F1-score, and AUC (entire sample: 0.707, 0.706, 0.791; Class II: 0.759, 0.758, 0.824; Class III: 0.822, 0.807, 0.89). CONCLUSIONS: The proposed combined 10 ML approach model accurately predicted the need for orthognathic surgery, showing better performance in Class III patients.

Is three-piece maxillary segmentation surgery a stable procedure?

Objective: : The number of three-piece maxillary osteotomies has increased over the years; however, the literature remains controversial. The objective of this study was to evaluate the skeletal stability of this surgical modality compared with that of one-piece maxillary osteotomy. Methods: : This retrospective cohort study included 39 individuals who underwent Le Fort I maxillary osteotomies and were divided into two groups: group 1 (three pieces, n = 22) and group 2 (one piece, n = 17). Three cone-beam computed tomography scans from each patient (T1, pre-surgical; T2, post-surgical; and T3, follow-up) were used to evaluate the three-dimensional skeletal changes. Results: : The differences within groups were statistically significant only for group 1 in terms of surgical changes (T2-T1) with a mean difference in the canine region of 3.09 mm and the posterior region of 3.08 mm. No significant differences in surgical stability were identified between or within the groups. The mean values of the differences between groups were 0.05 mm (posterior region) and -0.39 mm (canine region). Conclusions: : Our findings suggest that one- and three-piece maxillary osteotomies result in similar post-surgical skeletal stability.

Three-dimensional comparison between the effects of mandibular advancement device and maxillomandibular advancement surgery on upper airway.

BACKGROUND: The efficacy of mandibular advancement devices (MAD) and maxillomandibular advancement (MMA) in improving upper airway (UA) patency has been described as being comparable to continuous positive airway pressure (CPAP) outcomes. However, no previous study has compared MAD and MMA treatment outcomes for the upper airway enlargement. This study aimed to evaluate three-dimensionally the UA changes and mandibular rotation in patients after MAD compared to MMA. METHODS: The sample consisted of 17 patients with treated with MAD and 17 patients treated with MMA matched by weight, height, body mass index. Cone-beam computed tomography from before and after both treatments were used to measure total UA, superior/inferior oropharynx volume and surface area; and mandibular rotation. RESULTS: Both groups showed a significant increase in the superior oropharynx volume after the treatments (p = 0.003) and the MMA group showed greater increase (p = 0.010). No statistical difference was identified in the MAD group considering the inferior volume, while the MMA group showed a significantly gain (p = 0.010) and greater volume (p = 0.024). Both groups showed anterior mandibular displacement. However, the mandibular rotation were statistically different between the groups (p < 0.001). While the MAD group showed a clockwise rotation pattern (-3.97 ± 1.07 and - 4.08 ± 1.30), the MMA group demonstrated a counterclockwise (2.40 ± 3.43 and 3.41 ± 2.79). In the MAD group, the mandibular linear anterior displacement was correlated with superior [p = 0.002 (r=-0.697)] and inferior [p = 0.004 (r = 0.658)] oropharynx volume, suggesting that greater amounts of mandibular advancement are correlated to a decrease in the superior oropharynx and an increase in the inferior oropharynx. In the MMA group, the superior oropharynx volume was correlated to mandibular anteroposterior [p = 0.029 (r=-0.530)] and vertical displacement [p = 0.047 (r = 0.488)], indicating greater amounts of mandibular advancement may lead to a lowest gain in the superior oropharynx volume, while a great mandibular superior displacement is correlated with improvements in this region. CONCLUSIONS: The MAD therapy led to a clockwise mandibular rotation, increasing the dimensions of the superior oropharynx; while a counterclockwise rotation with greater increases in all UA regions were showed in the MMA treatment.

Three-dimensional craniofacial characteristics associated with obstructive sleep apnea severity and treatment outcomes.

OBJECTIVES: This study aims to assess craniofacial dimensions in obstructive sleep apnea (OSA) patients treated with a mandibular advancement device (MAD) and to identify anatomic influences on OSA severity and MAD therapy outcomes. MATERIALS AND METHODS: Twenty patients with OSA were prospectively treated with MAD. Clinical, cone-beam computed tomography, and polysomnography exams were performed before treatment and 4-6 months after achieving the MAD therapeutic position. Polysomnographic exams and three-dimensional maxillary, mandibular, and upper airway (UA) measurements were evaluated. Pearson's correlation and t-tests were applied. RESULTS: Before MAD treatment, the transverse width measured at the frontomaxillary suture and the angle between the mandibular ramus and Frankfurt horizontal were statistically correlated with apnea and the hypopnea index (AHI), while the gonial angle was correlated with therapeutic protrusion. After MAD treatment, all patients showed a significant AHI reduction and an improvement in minimum oxyhemoglobin saturation. The UA total volume, superior and inferior oropharynx volume, and area were statistically correlated with MAD therapeutic protrusion. The UA total area showed a statistical correlation with the improvement in AHI, and the superior oropharynx volume and area increased significantly. CONCLUSIONS: The transversal frontomaxillary suture width and the mandibular ramus facial angle may influence OSA severity. The gonial angle, volume, and area of all UA regions may indicate the amount of protrusion needed for successful MAD treatment. CLINICAL RELEVANCE: The craniofacial characteristics reported as important factors for OSA severity and MAD treatment outcomes impact therapy planning for OSA patients, considering individual anatomic characteristics, prognosis, and cost benefits.

Craniofacial and airway morphology of individuals with oculoauriculovertebral spectrum.

OBJECTIVES: The objectives of this study were to characterize the craniofacial and airway morphology of oculo-auriculo-vertebral spectrum (OAVS) individuals using computed tomography (CT) examination. SETTING AND SAMPLE POPULATION: This sample included individuals in the age range from 5 to 14 years, consisted of a group of 18 OAVS individuals (12 females and 6 males), Pruzansky-Kaban1 IIB and III and by a paired control group matched by age and sex for comparison of morphometric and airway variables. MATERIALS AND METHODS: Through the CT examination, airway analysis was performed using Dolphin Imaging® Software, and seven morphometric measurements were performed to evaluate craniofacial morphology by Materialize Mimics® Software. To compare airway and morphometric variables, the control group was used. Student's t test and Mann-Whitney U test were performed to compare differences between the groups. RESULTS: Statistically significant differences were showed between the control and OAVS groups for the variables: total airway (TA) area, volume and MAA, RP area, RP volume, RP MAA, RG volume, RG MAA, total posterior height diff, Md incl and y-axis asymmetry. Pearson and Spearman's correlation showed mostly moderate correlations between Mand Occlusal canting AS with TA area and RP volume, Ax-Gn with TA area and Hy-C3 with TA volume. CONCLUSIONS: The OAVS's airway was altered and worse than the control group. Our results suggest that the contralateral side of OAVS individuals is unaffected; however, longitudinal assessments are needed to confirm it. Hyoid bone and postural measures play an important role in interpreting airway features of individuals with and without OAVS.

Can palatal splint improve stability of segmental Le Fort I osteotomies?

OBJECTIVES: The purpose of this study was to evaluate the influence of a palatal splint on stability in multi-segment maxillary osteotomies. SETTING AND SAMPLE POPULATION: Retrospective series of fifty-one adult patients, consecutively operated with bilateral sagittal split osteotomy (BSSO) and three-piece maxillary osteotomies, divided according to the use of a palatal splint (Group 1, n = 30) or no palatal splint (Group 2, n = 21). MATERIALS AND METHODS: Maxillary surgical casts (T1) and post-retention casts (T2), taken at least six months after discontinuation of orthodontic retention, were digitized (MicroScribe-3DX), measured and compared. Fifty-one landmarks were identified on the maxillary, transverse dimension changes and arch length were calculated. Longitudinal changes in all measurements were assessed by t test. RESULTS: Post-surgical transverse instability in group 1 ranged from 0.3 ± 0.4 to -1.3 ± 0.2 mm and was statistically significantly smaller than in group 2 that ranged from -1.0 ± 0.3 to -2.5 ± 0.5 mm. CONCLUSIONS: The use of a palatal splint after segmental Le Fort I maxillary osteotomy improved transverse stability in the posterior region. The post-surgical transverse instability occurred only between canine gingival points and thus suggesting no clinical relevance.

Orthodontic Traction of Impacted Canine Using Cantilever.

The impaction of the maxillary canines causes relevant aesthetic and functional problems. The multidisciplinary approach to the proper planning and execution of orthodontic traction of the element in question is essential. Many strategies are cited in the literature; among them is the good biomechanical control in order to avoid possible side effects. The aim of this paper is to present a case report in which a superior canine impacted by palatine was pulled out with the aid of the cantilever on the Segmented Arch Technique (SAT) concept. A 14.7-year-old female patient appeared at clinic complaining about the absence of the upper right permanent canine. The proposed treatment prioritized the traction of the upper right canine without changing the occlusion and aesthetics. For this, it only installed the upper fixed appliance (Roth with slot 0.018), opting for SAT in order to minimize unwanted side effects. The use of cantilever to the traction of the upper right canine has enabled an efficient and predictable outcome, because it is of statically determined mechanics.

Osteoblast differentiation is enhanced by a nano-to-micro hybrid titanium surface created by Yb:YAG laser irradiation.

OBJECTIVES: The aim of this study was to analyze the capacity of a new modified laser surface to stimulate calvarial osteoblasts isolated from neonatal mouse bones to differentiate and form mineralized nodules. METHODS: Titanium discs were subjectezd or not to laser irradiation according to specific parameters and characterized. Osteoblasts isolated from neonatal mouse calvaria were cultured over the discs, and the capacity of these cells to proliferate (MTT assay), form mineralized nodules (Alizarin red assay), and enhance alkaline phosphatase activity (ALPase activity) was analyzed. Real-time PCR was used for quantification of gene expression. RESULTS: Laser-irradiated titanium discs (L) presented a rough nano-to-micrometric oxidized surface contrasting with the smooth pattern on polished discs (P). The Ra on the micrometric level increased from 0.32 ± 0.01 µm on P surfaces to 10.57 ± 0.39 µm on L surfaces. When compared with P, L promoted changes in osteoblast morphology, increased mineralized nodule formation in osteoblasts cultured on the surfaces for 14 days, and enhanced ALPase activity at days 7 and 14. Transcription factors triggering osteoblast differentiation (Runx2 and Sp7) and genes encoding the bone extracellular matrix proteins collagen type-1 (Col1a1), osteopontin (Spp1), and osteocalcin (Bglap) were upregulated in cells on L surfaces compared with those on P surfaces at days 1-14. CONCLUSION: Laser treatment of titanium surfaces created a rough surface that stimulated osteoblast differentiation. CLINICAL RELEVANCE: Laser treatment of titanium generates a reproducible and efficient surface triggering osteoblast differentiation that can be of importance for osteointegration.