Evaluation of a cooling/heating-assisted microextraction instrument using a needle trap device packed with aminosilica/graphene oxide nanocomposites, covalently attached to cotton.

A low-cost and reliable cooling/heating-assisted microextraction (CHaME) instrument was designed and fabricated for use in different modes of microextraction methods. The CHaME setup is able to cool down the sorbent and simultaneously heat the sample in a wide temperature range. Consequently, it can create a large thermal gap between the sorbent and the sample matrix, to promote the release of analytes from the sample tissue and enhance their effective trapping on the microextraction phase. The primary versions of the instrument have previously been evaluated, coupled with different modes of solid- and liquid-phase microextraction strategies. Compared with conventional microextraction systems, it is able to extract volatile organic compounds from complicated solid matrices more effectively, rapidly and without any need for a sample preparation step. In this research, the final and compact version of the CHaME instrument was fabricated and employed in a cooling/heating-assisted needle trap device (CHaME-NTD) for microextraction of polycyclic aromatic hydrocarbons (PAHs) in contaminated soil samples, prior to GC-FID determination. An aminosilica/graphene oxide nanocomposite was synthesized, covalently attached to cotton (Am-Si/GO/Cot), packed inside a needle, and applied as an effective sorbent for trapping of the analytes. The influence of experimental parameters on the extraction efficiency of the TC-NTD-GC-FID strategy was evaluated and optimized. Under the optimal conditions, linear dynamic ranges (LDRs), limits of detection (LODs), and relative standard deviations (RSDs) for the PAHs were 0.001-2.0 µg g-1, 5-38 pg g-1, and 6.2-9.8% (n = 6), respectively. The CHaME-NTD-GC-FID procedure was compared with the traditional NTD-GC-FID method. Additionally, the Am-Si/GO/Cot nanocomposite sorbent was compared with the most frequently used commercial sorbents. The results demonstrated the remarkable performance of the CHaME-NTD procedure and the Am-Si/GO/Cot composite sorbent. The developed setup was also used for the extraction and determination of PAHs in contaminated soil samples, through the CHaME-NTD-GC-FID procedure.

Practical method for evaluation of linearity and effective pathlength of on-capillary photometric detectors in capillary electrophoresis.

The optical characteristics of on-capillary photometric detectors for capillary electrophoresis were evaluated and five commercial detectors were compared. Plots of sensitivity (absorbance/concentration) versus absorbance obtained with a suitable testing solution yield both the linear range and the effective path length of the detector. The detector linearity is a crucial parameter when using absorbing electrolytes, such as for indirect photometric detection, and especially for highly absorbing electrolyte probe ions. The upper limits of the linear ranges (determined as 5% decline in sensitivity) for five commercial detectors ranged from 0.175 to 1.2 AU. The effective pathlength reflects the quality of the optical design of the detector and is equal to the capillary internal diameter only for a light beam passing exactly through the capillary centre, but becomes progressively shorter for imperfect optical designs. The determined effective pathlength for the five investigated detectors ranged from 49.7 to 64.6 microm for a 75 microm I.D. capillary.

Ion chromatography on-chip.

On-chip separation of inorganic anions by ion-exchange chromatography was realized. Micro separation channels were fabricated on a silicon wafer and sealed with a Pyrex cover plate using standard photolithography, wet and dry chemical etching, and anodic bonding techniques. Quaternary ammonium latex particles were employed for the first time to coat the separation channels on-chip. Owing to the narrow depths of the channels on the chip, 0.5-10 microm, there were more interactions of the analytes with the stationary phase on the chip than in a 50-microm I.D. capillary. With off-chip injection (20 nl) and UV detection, NO2-, NO3-, I-, and thiourea were separated using 1 mM KCl as the eluent. The linear ranges for NO2- and NO3- are from 5 to 1000 microM with the detection limits of 0.5 microM.

Approaches to enhancing the sensitivity of capillary electrophoresis methods for the determination of inorganic and small organic anions.

One of the major problems facing the development of capillary electrophoresis (CE) is the relatively high limits of detection when compared to traditional high-performance liquid chromatographic (HPLC) methods. While the use of an alternative detector can offer better sensitivity, a more universal approach is sample preconcentration. Numerous on-line methods have been developed to improve the sensitivity of CE, and are based on electrophoretic principles, chromatographic principles, or a combination of both. This review will discuss all forms of on-line preconcentration methods for CE, with emphasis given to those that have shown particular merit when applied to inorganic and small organic anions.

Separation of hydrophobic polymer additives by microemulsion electrokinetic chromatography.

Microemulsion electrokinetic chromatography (MEEKC) has been applied to the separation of some phenolic antioxidants [Irganox 1024, Irganox 1035, Irganox 1076, Irganox 1010, Irganox 1330, Irgafos 138, Irganox 168 and 2,6-di-tert.-butyl-4-methylphenol (BHT)]. Due to the extremely hydrophobic nature of these analytes, they could not be separated using standard MEEKC conditions and two alternative approaches were investigated. Using an acidic buffer (phosphate, pH 2.5) to effectively suppress the electroosmotic flow, the addition of 2-propanol to the aqueous phase of the microemulsion buffer to improve partitioning of the analytes, and a negative separation voltage, separation of five of the analytes in under 10 min was possible. The second approach, using a basic buffer (borate, pH 9.2) and a positive separation voltage resulted in complete resolution of all eight analytes. A mixed surfactant system comprising the anionic sodium dodecyl sulfate (SDS) and neutral Brij 35 was used to reduce the overall charge and with it the mobility of the droplets, and hence the separation time. Using an optimised MEEKC buffer consisting of 2.25% (w/w) SDS, 0.75% (w/w) Brij 35, 0.8% (w/w) n-octane, 6.6% (w/w) 1-butanol, 25% (w/w) 2-propanol and 64.6% (w/w) 10 mM borate buffer (pH 9.2) the eight target analytes were baseline separated in under 25 min. For these analytes, MEEKC was found to be superior to micellar electrokinetic chromatography in every respect. Specifically, the solubility of the analytes was better, the selectivity was more favourable, the analysis time was shorter and the separation efficiency was up to 72% higher when using the MEEKC method. Detection limits from 5.4 to 26 microg/ml were obtained and the calibration plot was linear over more than one order of magnitude. The optimised method could be applied to the determination of Irganox 1330 and Irganox 1010 in polypropylene.

A mechanism of separation in electrostatic ion chromatography.

The retention mechanism of electrostatic ion chromatography (EIC) is currently under debate and is the focus of this paper. A comprehensive set of retention data has been obtained on a C18 column coated with the zwitterionic surfactant 3-(N,N-dimethylmyristylammonio)propanesulfonate used with a range of mobile phases in which both the mobile-phase anion and cation have been varied systematically. Electro-osmotic flow measurements were also obtained on fused-silica capillaries coated with the zwitterion (and also some monofunctional surfactants) and were used to evaluate the nature of the surface charge on the layer of adsorbed surfactant in the presence of various background electrolytes. A new retention mechanism for EIC was developed on the basis of these data. This mechanism proposes that equilibration of the bound zwitterions with a mobile phase containing a suitable electrolyte causes the establishment of a charged layer created by the terminal sulfonate groups of the zwitterion, which acts as a Donnan membrane. The magnitude and polarity of the charge on this membrane depends on the nature of the mobile-phase ions. The Donnan membrane exerts weak electrostatic repulsion or attraction effects on analyte anions. A second component of the retention mechanism is chaotropic interaction of the analyte anion with the quaternary ammonium functional group of the zwitterion. This interaction exerts the major effect on the separation selectivity of EIC, such that analyte anions are eluted in order of increasing chaotropic interactions in accordance with the Hofmeister series.

High-performance ion-exclusion/cation-exchange chromatography of anions and cations in acid rain waters on a weakly acidic cation-exchange resin.

A new method for the simultaneous determination of anions (sulfate, nitrate, and chloride) and cations (sodium, ammonium, potassium, magnesium, and calcium) in acid rain waters was investigated using high-performance ion-exclusion/cation-exchange chromatography with conductimetric detection on a separation column packed with a polymethacrylate-based weakly acidic cation-exchange resin in the hydrogen-form and an eluent comprising 1.5 mM sulfosalicylic acid-6 mM 18-crown-6 at pH 2.6, operated at 1.5 ml/min. Effective separation and highly sensitive conductimetric detection for the anions and the cations was achieved in about 14 min. Since the ionic balance (equivalents of anions/equivalents of cations) of acid rain waters of different pH (4.40-4.67) ranged from 0.97 to 0.94, evaluation of the water quality of acid rain was possible. This method was successfully applied to the simultaneous determination of the anions and the cations in acid rain transported from mainland China and North Korea to central Japan monitored by a meteorological satellite data analyzer.

Retention modelling of electrostatic and adsorption effects of aliphatic and aromatic carboxylic acids in ion-exclusion chromatography. II. Calculations of adsorption coefficients in unbuffered eluents.

Previous models for the retention behaviour of carboxylic acids in ion-exclusion chromatography are applicable only when the degree of ionisation of the analyte is constant over the entire chromatographic peak. When solutions of sulfuric acid are used as eluents, this condition applies only when the eluent concentration is considerably higher than that of the analyte. Since it is common for dilute solutions of sulfuric acid to be used as eluents, a retention model which accounts for unbuffered eluents has been developed. This model also considers the effects on retention of hydrophobic adsorption of the undissociated and dissociated forms of the analyte onto the stationary phase substrate, as well as the effects of organic solvents added to the eluent. The derivation of this model is presented and it has been evaluated using a comprehensive set of retention data obtained using three different sulfonated stationary phases over a range of eluent conditions. The adsorption coefficients calculated from the model are in accordance with expected trends and showed that both the undissociated and dissociated forms of the analyte acids were retained by hydrophobic adsorption effects, although this adsorption was much stronger for the undissociated analytes.

Manipulation of separation selectivity of inorganic anions in electrostatic ion chromatography by the use of mixed cationic-zwitterionic micelles as the column coating solution.

This paper describes an electrostatic ion chromatographic system in which the separation selectivity for inorganic anions, especially for sulfate and phosphate, could be manipulated by altering the molar ratio of the zwitterionic and cationic surfactants in the column coating solution used to prepare the stationary phase. The zwitterionic surfactant used for this study was 3-(N,N-dimethyltetradecylammonio)propanesulfonate (Zwittergent-3-14) and the cationic surfactant was tetradecyltrimethylammonium (TTA). Using a reversed-phase C18 column (250x4.6 mm I.D.) coated with 10/10 (mM/mM) of TTA/Zwittergent-3-14 mixed micelles as the stationary phase and either NaHCO3 or Na2CO3 aqueous solution as the eluent, together with suppressed conductivity detection, baseline separation of seven model inorganic anions was obtained. The elution order for those anions was found to be F+ < HPO4(2-) < Cl- < SO4(2-) < NO2- < Br- < NO3-. Under the same conditions but using 1/10 (mM/mM) of TTA/Zwittergent-3-14 mixed micelles as the column coating solution, the elution order for these model ions was F- < HPO4(2-) < SO4(2-) < Cl- < NO2- < Br- < NO3-. The early elution of phosphate and sulfate is a unique attribute of this system. Detection limits for F-, HPO4(2-), Cl-, SO4(2-), NO2-, Br- and NO3- (S/N=3, sample injection volume 100 microl) were 0.11, 0.12, 0.12, 0.18, 0.49, 0.49, 0.52 microM, respectively.

A novel ion chromatographic method based on cation-exchange and acid-base interactions for the simultaneous determination of total alkalinity and monovalent cations in samples of microliter volume.

An ion chromatographic (IC) method based on the use of titrant (strong acid) as the stationary phase was developed for simultaneous determination of total alkalinity (TA) and monovalent cations. The titrant used in this study was obtained by initially loading lithium dodecylsulfate (Li-DS) onto a reversed-phase material and then conditioning the column with a slightly acidified aqueous LiCl solution (a mixture of 50.0 mM LiCl and 0.1 mM H2SO4). When a small amount of a basic sample was injected onto a column prepared in this way, the basic species (Bn-) reacted predominantly with H+ on the stationary phase and the reaction with the eluent phase was negligible due to the very low concentration of eluent H+ (in the eluent, a molar ratio of [Li+]/[H+] = 250:1 applied). The stationary phase H+ consumed in the acid-base reaction was then re-supplied by H+ from the eluent. By monitoring the conductance of the eluent using conductivity, an induced peak resulting from the basic species was observed. Calibration graphs of peak areas vs. molar concentration of the basic species for OH-, HCO3- and H2PO4- were found to be identical. CO3(2-), HPO4(2-), and B4O7(2-) also gave identical calibration curves but their slope values were twice those for HCO3-. The detection limit for HCO3- was less than 3.2 microM and the calibration curve was linear up to 12.3 mM (injection volume, 100 microL). Seawater was directly analyzed and its total alkalinity was found to be 2.87 mM (RSD 0.53%, n = 5), which was in good agreement with the result of 2.88 mM (RSD 3.2%, n = 5) obtained using auto-potentiometric titration. Na+ and K+ were determined simultaneously and the concentrations were 481.6 and 10.6 mM, respectively.

Simultaneous ion-exclusion chromatography and cation-exchange chromatography of anions and cations in environmental water samples on a weakly acidic cation-exchange resin by elution with pyridine-2,6-dicarboxylic acid.

A non-suppressed conductivity detection ion chromatographic method using a weakly acidic cation-exchange column (Tosoh TSKgel OApak-A) was developed for the simultaneous separation and determination of common inorganic anions (Cl-, NO3- and SO4(2-)) and cations (Na+, NH4+, K+, Mg2+ and Ca2+). A satisfactory separation of these anions and cations on the weakly acidic cation-exchange column was achieved in 25 min by elution with a mixture of 1.6 mmol L-1 pyridine-2,6-dicarboxylic acid and 8.0 mmol L-1 18-crown-6 at flow rate of 1.0 mL min-1. On this weakly acidic cation-exchange resin, anions were retained by an ion-exclusion mechanism and cations by a cation-exchange mechanism. The linear range of the peak area calibration curves for all analytes were up to two orders of magnitude. The detection limits calculated at S/N = 3 ranged from 0.25 to 1.9 mumol L-1 for anions and cations. The ion-exclusion chromatography-cation-exchange chromatography method developed in this work was successfully applied to the simultaneous determination of major inorganic anions and cations in rainwater, tap water and snow water samples.

New isoelectric buffers for capillary electrophoresis: N-carboxymethylated polyethyleneimine as a macromolecular isoelectric buffer.

Isoelectric buffers are attractive for electrophoresis because of their low conductivity, and their compatibility with indirect photometric detection in capillary electrophoresis (CE) where they do not interfere with the detection by exhibiting competitive displacement of the UV-absorbing probe ion. N-carboxymethylated polyethyleneimine (CMPEI) was prepared by introducing a half molar equivalent of carboxylate groups onto a polyethyleneimine backbone. Its isoelectric point determined by conductometric titration and from the pH of its dilute aqueous solution is approx. 6.8, which allows isoelectric buffering at a lower pH compared to histidine (pI7.7). Although the isoelectric point is somewhat diffuse, as expected for a polymeric compound, it exhibits a buffering capacity at a pI point of about twice that of histidine. Studies of electroosmotic flow (EOF) profile at various pH values in fused silica capillaries showed that CMPEI adsorbs onto the fused silica wall and reverses the EOF at pH < 6.5. CMPEI was applied as a buffer in an electrolyte containing 0.5 mM of the anionic dye tartrazine used as the probe for indirect detection of anions. The separation system exhibited a stable baseline, no system peaks, separation efficiencies of up to 195,000 theoretical plates, and detection limits down to 0.2 microM or 2 amol of injected analyte.

Anion-exchange capillary electrochromatography with indirect UV and direct contactless conductivity detection.

Conductivity detection is applied to ion-exchange capillary electrochromatography (IE-CEC) with a packed stationary phase, using a capacitively coupled contactless conductivity detector with detection occurring through the packed bed. Columns were packed with a polymeric latex-agglomerate anion-exchanger (Dionex AS9-SC). A systematic approach was used to determine suitable eluants for IE-CEC separations using simultaneous indirect UV and direct conductivity detection. Salicylate and p-toluenesulfonate were identified as potential eluant competing anions having sufficient eluotropic strength to induce changes in separation selectivity, but salicylate was found to be unsuitable with regard to baseline stability. It was also found for both indirect UV and direct conductivity detection that homogenous column packing was imperative, and monitoring of the baseline could be used to assess the homogeneity of the packed bed. Using a p-toluenesulfonate eluant, the separation of eight common anions was achieved in 2.5 min. Direct conductivity detection was found to be superior to indirect UV detection with regard to both baseline stability and detection sensitivity with detection limits of 4-25 microg/L being obtained. However, the calibration for each anion was not linear over more than one order of magnitude. When using conductivity detection, the concentration of the eluant could be varied over a wider range (2.5-50 mM p-toluenesulfonate) than was the case with indirect UV detection (2.5-10 mM), thereby allowing greater changes in separation selectivity to be achieved. By varying the concentration of p-toluenesulfonate in the eluant, the separation selectivity could be manipulated from being predominantly ion-exchange in nature (2.5 mM) to predominantly electrophoretic in nature (50 mM).

Fast separation of pyrimidine derivatives by capillary electrochromatography on ion-exchange/reversed-phase mixed-mode stationary phases.

This work describes the use of mixed-mode stationary phases which exhibit both strong ion-exchange (either cation-exchange, SCX, or anion-exchange, SAX) and reversed-phase chromatographic characteristics in capillary electrochromatographic separations of pyrimidine derivatives. Different packing materials, namely C6, SCX/C6 and SAX/C6, were compared and the influence of the composition of the carrier electrolyte (concentration of acetonitrile and pH) on the retention behavior of the selected solutes was investigated. A separation of all eight pyrimidine derivatives could be obtained on a 6.5 cm column packed with the SAX/C6 stationary phase in less than 3 min, with good peak shapes and efficiencies in the range 39,000 to 81,000 plates per meter.

On-capillary ion-exchange preconcentration of inorganic anions in open-tubular capillary electrochromatogrpahy with elution using transient-isotachophoretic gradient. 2. Characterization of the isotachophoretic gradient.

Diffuse transient-isotachophoretic boundaries can be used as an elution gradient of increasing eluotropic strength to elute inorganic anions that have been preconcentrated on an open-tubular ion-exchange stationary phase prior to electrophoretic separation. The generation and characteristics of these gradients for elution after preconcentration have been investigated. The gradients are generated by placing a low-mobility, weak ion-exchange competing anion in the capillary (weak electrolyte, WE), and a high-mobility, strong ion-exchange competing anion in the electrolyte vials (strong electrolyte, SE). Application of voltage establishes a diffuse boundary with the composition changing from the weak anion to the strong anion. Comparison of elution gradients generated with different electrolyte systems was accomplished by comparing the eluotropic strength (a function of eluent concentration, ion-exchange selectivity coefficient, and charge) and the shape of the profile as it changes from WE to SE. The ion-exchange selectivity coefficient of the SE competing anion is important in establishing a sharp change in elution strength. A large difference in mobility between the WE and SE competing anions gives an SE with a higher final eluotropic strength, but the slope of the gradient is shallower. This results in a reduction in the efficiency of analyte focusing. To ensure maximum focusing efficiency, the WE and SE electrolytes should be selected such that the SE has the highest possible eluotropic strength for a given concentration of WE. The SE competing anion should also have a sufficiently low electrophoretic mobility to ensure focusing for the maximum number of analytes, and the mobility difference between the WE and SE competing anions should be as small as possible.

Prediction of retention times for anions in linear gradient elution ion chromatography with hydroxide eluents using artificial neural networks.

The feasibility of using an artificial neural network (ANN) to predict the retention times of anions when eluted from a Dionex AS11 column with linear hydroxide gradients of varying slope was investigated. The purpose of this study was to determine whether an ANN could be used as the basis of a computer-assisted optimisation method for the selection of optimal gradient conditions for anion separations. Using an ANN with a (1, 10, 19) architecture and a training set comprising retention data obtained with three gradient slopes (1.67, 2.50 and 4.00 mM/min) between starting and finishing conditions of 0.5 and 40.0 mM hydroxide, respectively, retention times for 19 analyte anions were predicted for four different gradient slopes. Predicted and experimental retention times for 133 data points agreed to within 0.08 min and percentage normalised differences between the predicted and experimental data averaged 0.29% with a standard deviation of 0.29%. ANNs appear to be a rapid and accurate method for predicting retention times in ion chromatography using linear hydroxide gradients.

Modelling of migration behaviour of inorganic anions in ion-exchange capillary electrochromatography.

A theoretical model to explain the observed mobility of inorganic anions in capillary electrochromatography (CEC) using ion-exchange (IE) stationary phases has been derived. The model divides contributions to the observed mobility of an analyte ion into capillary electrophoretic (CE) and IE components. The CE component includes the influence of varying the ionic strength of the background electrolyte on the electrophoretic mobility of the analyte, while the IE component accounts for the variation in retention of the analyte ion caused by changing the composition of the background electrolyte. The model was verified using a mixture of UV-absorbing inorganic ions in electrolytes of differing eluotropic strength in both packed and open-tubular CEC systems, with excellent agreement (r2 > 0.98) for both systems. Values of constants in the model equation determined by nonlinear regression were used to estimate the relative strengths of the interactions of different analytes with the stationary phase and these were found to agree well with elution orders observed in conventional IE chromatography.

Statistical analysis of decay of organophosphorus and pyrethroid insecticides and carbaryl on paddy rice, maize, sunflowers and field peas.

A model is developed to describe the decay of seven insecticides on stored paddy rice, maize, sunflowers and peas, and is shown to be more precise than each of six literature models on pesticide decay. It relates residues (R), as a ratio of applied concentration (R(0)), to time after insecticide application (t), modifying the usual first-order kinetics equation lnR=lnR(0)-kt by assuming that the rate constant k has a mixture of values according to a gamma distribution with mean K. The resulting equation is lnR=lnR(0)-Kcln(1+t/c), where c is a constant determined empirically. For large c, this model reduces to the first-order model with K=k. The parameter K is further modelled as linear in temperature for maize and rice. The rate of loss of protectants was found not to be seriously affected by co-application with other insecticides, and this is a useful finding for future studies on rates of loss of grain protectants. The apparent rate of loss was also not seriously affected by the method of analysis, whether by gas chromatography or high-performance liquid chromatography, and this finding supports previous validation of the methods.