ABSTRACT
The preparation of pellets using a high-shear granulator in a rapid single-step is considered a good economic alternative to the extrusion spheronization process. As process parameters and material attributes greatly affect pellet qualities, successful process optimization plays a vital role in producing pellet dosage forms with the required critical quality attributes. This study was aimed at the development and optimization of the pelletization technique with the Pro-CepT granulator. According to the quality by design (QbD) and screening design results, chopper speed, the volume of the granulating liquid, binder amount, and impeller speed were selected as the highest risk variables for a two-level full factorial design and central composite design, which were applied to the formula of microcrystalline cellulose, mannitol, and with a binding aqueous polyvinylpyrrolidone solution. The design space was estimated based on physical response results, including the total yield of the required size, hardness, and aspect ratio. The optimized point was tested with two different types of active ingredients. Amlodipine and hydrochlorothiazide were selected as model drugs and were loaded into an optimized formulation. The kinetics of the release of the active agent was examined and found that the results show a correlation with the electrokinetic potential because amlodipine besylate can be adsorbed on the surface of the MCC, while hydrochlorothiazide less so; therefore, in this case, the release of the active agent increases. The research results revealed no significant differences between plain and model drug pellets, except for hydrochlorothiazide yield percent, in addition to acceptable content uniformity and dissolution enhancement.
ABSTRACT
Hydrophobic ion pairing (HIP) complexation was found to be an efficient approach in modulating the release and enhancing the stability and encapsulation of hydrophilic macromolecules such as proteins in hydrophobic nano/microcarriers. The present work strives to develop and optimize the preparation of the HIP complex of the antimicrobial enzyme lysozyme (LYZ) with the ion-pairing agent (IPA) sodium dodecyl sulphate (SDS) relying on the quality-by-design (QbD) approach. The quality target product profile (QTPP) includes the achievement of maximal lipophilicity in a reversible manner to enable the maintenance of biological activity. The related critical quality attributes (CQAs) were defined as complexation efficacy, complex stability, enzyme recovery and activity. Three risk assessment (RA) tools were used to identify and rank the critical process parameters (CPPs) and critical material attributes (CMAs). From this assessment, the pH of the medium, LYZ:SDS molar ratio and drying conditions were determined as high-risk factors that need to be investigated. To the best of our knowledge, for the first time, electrostatic titration was used as a smart approach to determine the optimum molar ratio at different pH values. Based on the predefined CQAs, pH 8 with an LYZ/SDS molar ratio of 1:8 was found to be the optimal condition for complexation efficiency and recovery (%) of a biologically active enzyme. A cost-effective drying process based on a ventilated oven was developed, which resulted in complex qualities comparable to those obtained by the commonly used freeze-drying method. In a nutshell, the optimum conditions for the preparation of the LYZ/SDS HIP complex were efficiently facilitated by the rational application of QbD principles and the utilization of efficient electrostatic titration and ventilated oven-drying methods.
ABSTRACT
Mucoadhesive buccal films have found increased popularity in pharmaceutical drug delivery due to the several advantages that they possess. The present study strives to develop and optimize chitosan-based mucoadhesive buccal films by relying on quality-by-design (QbD) principles. Previous knowledge and experience were employed to firstly identify the critical quality attributes (CQAs), followed by a thorough risk assessment, which led to the selection of seven critical material attributes and process parameters, namely, the polymer grade and concentration, the plasticizer type and concentration, the citric acid (CA) concentration, the amount of the casted solution, and the drying condition. Their effects on the breaking hardness and mucoadhesivity, selected as CQAs, were investigated in three steps by three designs of the experiment (DoE). The medium molecular weight of chitosan (CH) was the preferred choice in the optimized formulation, and its concentration was the most important factor affecting the CQAs, thickness, and moisture content of the films. It was found that 0.364 g/cm2 was the suitable amount of the casting solution, and its optimum drying conditions were presented in the form of a design space. Glycerol (Gly) was the best choice as a plasticizer, and a design space representing several combinations of CH and CA concentrations that produce films with the required quality was constructed at a fixed concentration of 35% Gly. A formula from this design space was selected and employed to load with two model drugs to test its drug-carrying properties for drugs with different physicochemical characteristics. Uniform drug distribution with an immediate release profile was achieved in both drugs, although one of the CQAs was outside of the specifications in the case of lidocaine-containing film. To summarize, the obtention of the optimum mucoadhesive buccal film based on CH was efficiently facilitated by the rational application of QbD principles and the DoE approach.