Flow cytometry of Escherichia coli on microfluidic devices.

Flow cytometry of the bacterium Escherichia coli was demonstrated on a microfabricated fluidic device (microchip). The channels were coated with poly(dimethylacrylamide) to prevent cell adhesion, and the cells were transported electrophoretically by applying potentials to the fluid reservoirs. The cells were electrophoretically focused at the channel cross and detected by coincident light scattering and fluorescence. The E. coli were labeled with a membrane-permeable nucleic acid stain (Syto15), a membrane-impermeable nucleic acid stain (propidium iodide), or a fluorescein-labeled antibody and counted at rates from 30 to 85 Hz. The observed labeling efficiencies for the dyes and antibody were greater than 94%.

Electroosmotically induced hydraulic pumping with integrated electrodes on microfluidic devices.

Electroosmotic manipulation of fluids was demonstrated using thin metal electrodes integrated within microfluidic channels at the substrate and cover plate interface. Devices were fabricated by photolithographically patterning electrodes on glass cover plates that were then bonded to polymeric substrates into which the channels were cast. Polymeric substrates were used to provide a permeable membrane for the transport and removal of gaseous electrolysis products generated at the electrodes. Electroosmotic flow between interdigitated electrodes was demonstrated and provided electric field-free pumping of fluids in sections of the channel outside of the electrode pairs. The resultant pumping velocities were shown to be dependent on the applied voltage, not on the applied field strength, and independent of the length of the electroosmotically pumped region.

Two-dimensional electrochromatography/capillary electrophoresis on a microchip.

A two-dimensional separation system on a microfabricated device was demonstrated using open-channel electrochromatography as the first dimension and capillary electrophoresis as the second dimension. The first dimension was operated under isocratic conditions, and the effluent from the first dimension was repetitively injected into the second dimension every few seconds. A 25-cm separation channel with spiral geometry for open-channel electrochromatography was chemically modified with octadecylsilane and coupled to a 1.2-cm straight separation channel for capillary electrophoresis. Fluorescently labeled products from tryptic digests of beta-casein were analyzed in 13 min with this system.

Electrophoretic injection bias in a microchip valving scheme.

The pinched injection strategy, implemented on microfabricated fluidic devices (microchips), was investigated for an electrophoretic injection bias. Both the sample loading and dispensing steps were found to contribute to the injection bias whereby neutral species were injected preferentially to anionic species. In the sample loading step, neutral species filled a larger volume in the cross intersection than anionic species. Similarly, in the dispensing step, a larger volume of neutral analyte was injected than anionic analyte. Up to a 27% difference in injected volumes was observed. Fluorescently labeled amino acids were used as model analytes.

Novel microfabricated device for electrokinetically induced pressure flow and electrospray ionization mass spectrometry.

A novel microchip device for electrospray ionization has been fabricated and interfaced to a time-of-flight mass spectrometer. Fluid is electrokinetically transported through the chip to a fine fused-silica capillary inserted directly into a channel at the edge of the device. Electrospray is established at the tip of the capillary, which assures a stable, efficient spray. The electric potential necessary for electrospray generation and the voltage drop for electroosmotic pumping are supplied through an electrically permeable glass membrane contacting the fluidic channel holding the capillary. The membrane is fabricated on the microchip using standard photolithographic and wet chemical etching techniques. Performance relative to other microchip electrospray sources has been evaluated and the device tested for potential use as a platform for on-line electrophoretic detection. Sensitivity was found to be approximately three orders of magnitude better than spraying from the flat edge of the chip. The effect of the capillary on electroosmotic flow was examined both experimentally and theoretically.

Electrophoretic separation of proteins on a microchip with noncovalent, postcolumn labeling.

Proteins were separated by microchip capillary electrophoresis and labeled on-chip by postcolumn addition of a fluorogenic dye, NanoOrange, for detection by laser-induced fluorescence. NanoOrange binds noncovalently with hydrophobic protein regions to form highly fluorescent complexes. Kinetic measurements of complex formation on the microchips suggest that the reaction rate is near the diffusion limit under the conditions used for protein separation. Little or no band broadening is caused by the postcolumn labeling step. Lower limits of detection for model proteins, alpha-lactalbumin, beta-lactoglobulin A, and beta-lactoglobulin B, were <0.5 pg (approximately 30 amol) of injected sample. The relative fluorescence and reaction rates are compared with those of a number of other fluorogenic dyes used for protein labeling.

Integrated microchip-device for the digestion, separation and postcolumn labeling of proteins and peptides.

A microchip device was demonstrated that integrated enzymatic reactions, electrophoretic separation of the reactants from the products and post-separation labeling of proteins and peptides prior to detection. A tryptic digestion of oxidized insulin B-chain was performed in 15 min under stopped flow conditions in a heated channel, and the separation was completed in 1 min. Localized thermal control of the reaction channel was achieved using a resistive heating element. The separated reaction products were then labeled with naphthalene-2,3-dicarboxaldehyde (NDA) and detected by laser-induced fluorescence. A second reaction at elevated temperatures was also demonstrated for the on-chip reduction of disulfide bridges using insulin as a model protein. This device represents one of the highest levels, to date, of monolithic integration of chemical processes on a microchip.

Integrated system for rapid PCR-based DNA analysis in microfluidic devices.

An integrated system for rapid PCR-based analysis on a microchip has been demonstrated. The system couples a compact thermal cycling assembly based on dual Peltier thermoelectric elements with a microchip gel electrophoresis platform. This configuration allows fast (approximately 1 min/ cycle) and efficient DNA amplification on-chip followed by electrophoretic sizing and detection on the same chip. An on-chip DNA concentration technique has been incorporated into the system to further reduce analysis time by decreasing the number of thermal cycles required. The concentration injection scheme enables detection of PCR products after performing as few as 10 thermal cycles, with a total analysis time of less than 20 min. The starting template copy number was less than 15 per injection volume.

Characterization of cellular optoporation with distance.

We have developed and characterized cellular optoporation with visible wavelengths of light using standard uncoated glass cover slips as the absorptive media. A frequency-doubled Nd:YAG laser pulse was focused at the interface of the glass surface and aqueous buffer, creating a stress wave and transiently permeabilizing nearby cells. Following optoporation of adherent cells, three spatial zones were present which were distinguished by the viability of the cells and the loading efficiency (or number of extracellular molecules loaded). The loading efficiency also depended on the concentration of the extracellular molecules and the molecular weight of the molecules. In the zone farthest from the laser beam (> 60 microns under these conditions), nearly all cells were both successfully loaded and viable. To illustrate the wider applicability of this optoporation method, cells were loaded with a substrate for protein kinase C and the cellular contents then analyzed by capillary electrophoresis. In contrast to peptides loaded by microinjection, optoporated peptide showed little proteolytic degradation, suggesting that the cells were minimally perturbed. Also demonstrating the potential for future work, cells were optoporated and loaded with a fluorophore in the enclosed channels of microfluidic devices.

Microchip devices for high-efficiency separations.

We have fabricated a 25-cm-long spiral-shaped separation channel on a glass microchip with a footprint of only 5 cm x 5 cm. Electrophoretic separation efficiencies for dichlorofluoroscein (DCF) on this chip exceeded 1,000,000 theoretical plates and were achieved in under 46 s at a detection point 22.2 cm from the injection cross. The number of theoretical plates increased linearly with the applied voltage, and at a separation field strength of 1,170 V/cm, the rate of plate generation was approximately 21,000 plates/s. The large radii of curvature of the turns minimized the analyte dispersion introduced by the channel geometry as evidenced by the fact that the effective diffusion coefficient of DCF was within a few percent of that measured on a microchip with a straight separation channel over a wide range of electric field strengths. A micellar electrokinetic chromatography separation of 19 tetramethylrhodamine-labeled amino acids was accomplished in 165 s with an average plate number of 280,000. The minimum resolution between adjacent peaks for this separation was 1.2.

Effects of the electric field distribution on microchip valving performance.

Valving characteristics on microfluidic devices were controlled through manipulation of the electric field strengths during both the sample loading and dispensing steps. Three sample loading profiles for the constant volume valve (pinched injection) in conjunction with four dispensing schemes were investigated to study valving performance. The sample confinement profiles for the sample loading step consisted of a weakly pinched sample, a medium pinched sample, and a strongly pinched sample. Four dispensing schemes varied the electric field strengths in the sample and sample waste channels relative to the analysis channel to control the volume of the sample dispensed from the valve. The axial extent of the sample plug decreased as the electric field strengths in the sample and sample waste channels were raised relative to the analysis channel. In addition, a trade-off existed between sample plug length and sensitivity.

Microfabricated porous membrane structure for sample concentration and electrophoretic analysis.

A microfabricated injection valve incorporating a porous membrane structure is reported that enables electrokinetic concentration of DNA samples using homogeneous buffer conditions followed by injection into a channel for electrophoretic analysis. The porous membrane was incorporated in the microchannel manifold by having two channels separated from each other by 3-12 microns and connected by a thin porous silicate layer. This design allows the passage of current to establish an electrical connection between the separated channels but prevents large molecules, e.g., DNA, from traversing the membrane. Concentrated DNA can be injected into the separation channel and electrophoretically analyzed. Experiments exhibit a nonlinear increase in concentration with time, and DNA fragments can be concentrated up to 2 orders of magnitude as shown by comparison of peak intensities for analysis performed with and without concentration.

Microchip flow cytometry using electrokinetic focusing.

Flow cytometry of fluorescently labeled and unlabeled latex particles is demonstrated on a microfabricated device. The latex particles were detected and counted using laser light scattering and fluorescence coincidence measurements. Sample confinement was accomplished using electrokinetic focusing at a cross intersection, and detection occurred 50 µm downstream from the intersection. Particles with diameters of 1 and 2 µm were analyzed and distinguished from each other based on their light scattering intensity and fluorescence. A maximum sample throughput of 34 particles/s was achieved. Sample mixtures with varying proportions of fluorescently labeled and unlabeled particles were also analyzed and found to be within experimental error of the expected ratios.

Minimizing the number of voltage sources and fluid reservoirs for electrokinetic valving in microfluidic devices.

A microchip gated valve is demonstrated that uses a single voltage source and three fluid reservoirs. The fluidic valve is a cross intersection, and the channels are dimensioned to perform the appropriate voltage division, simplifying the voltage control hardware. A single voltage source is applied directly to the sample reservoir and through a high-voltage relay to the buffer reservoir, and the waste reservoir is grounded. The volume of sample dispensed is determined by the duration that the high-voltage relay is open. Volumetric reproducibility is demonstrated to be <0.5% relative standard deviation for volumes of ≥20 pL. The valve is tested for the minimum applied voltage necessary for leakage-free operation, i.e., sample diffusing from the cross intersection into the analysis channel. Moreover, appropriate channel dimensions are used to minimize the number of fluid reservoirs allowing effluent from the analysis and waste channels to be combined into a single reservoir.

Multiple sample PCR amplification and electrophoretic analysis on a microchip.

Polymerase chain reactions (PCRs) were carried out on as many as four DNA samples at a time on a microchip device. The PCR products were then analyzed, either individually or together on the same device, by microchip gel electrophoresis. A standard PCR protocol was used to amplify 199- and 500-base pair (bp) regions of bacteriophage lambda DNA and 346- and 410-bp regions of E. coli genomic and plasmid DNAs, respectively. Thermal lysis of the bacteria was integrated into the PCR cycle. A product sizing medium, poly(dimethylacrylamide), and an intercalating dye for fluorescence detection were used in the electrophoretic analysis of the products. PCR product sizes were determined by coelectrophoresis with marker DNA.

Degenerate oligonucleotide primed-polymerase chain reaction and capillary electrophoretic analysis of human DNA on microchip-based devices.

Random amplification of the human genome using the degenerate oligonucleotide primed-polymerase chain reaction (DOP-PCR) was performed in a silicon-glass chip. An aliquot of the DOP-PCR amplified genomic DNA was then introduced into another silicon-glass chip for a locus-specific, multiplex PCR of the dystrophin gene exons in order to detect deletions causing Duchenne/Becker muscular dystrophy. Amplicons were analyzed by both conventional capillary electrophoresis and microchip electrophoresis and results were compared to those obtained using standard non-chip-based PCR assays. Results from microchip electrophoresis were consistent with those from conventional capillary electrophoresis. Whole genome amplification products obtained by DOP-PCR proved to be a suitable template for multiplex PCR as long as amplicon size was < 250 bp. Successful detection and resolution of all PCR products from the multiplex PCR clearly shows the feasibility of performing complex PCR assays using microfabricated devices.

Microchip device for cell lysis, multiplex PCR amplification, and electrophoretic sizing.

The steps of cell lysis, multiplex PCR amplification, and electrophoretic analysis are executed sequentially on a monolithic microchip device. The entire microchip is thermally cycled to lyse cells and to amplify DNA, and the products are then analyzed using a sieving medium for size separation and an intercalating dye for fluorescence detection. Using a standard PCR protocol, a 500-base pair (bp) region of bacteriophage lambda DNA and 154-, 264-, 346-, 410-, and 550-bp regions of E. coli genomic and plasmid DNAs are amplified. The electrophoretic analysis of the products is executed in <3 min following amplification using hydroxyethyl cellulose or poly(dimethylacrylamide) sieving gels. Product sizing is demonstrated by proportioning the amplified product with a DNA sizing ladder.