Sequential extraction of fucoidan, laminarin, mannitol, alginate and protein from brown macroalgae Ascophyllum nodosum and Fucus vesiculosus.

The study involves development of a green biorefinery process for obtaining fucoidan, laminarin, mannitol, alginate and protein from dry and fresh Fucus vesiculosus and Ascophyllum nodosum using hydrochloric acid and a green extraction solvent. After the extraction of fucoidan which was the targeted biomolecule, an extract and by-product (residual biomass) were obtained. The extract was passed through an ultrafiltration membrane, where fucoidan was obtained in the ultrafiltration retentate while ultrafiltration permeate was analysed for laminarin and mannitol. The residual biomass was used for obtaining alginate using ultrasound (20 kHz, 64 % amplitude and 32 min, optimum parameters for alginate extraction based on our previous study). All the samples, showed good results for alginate, laminarin and mannitol, indicating that the by-products can be utilised using this green extraction process. The comparison of both dry and fresh seaweed is relevant from an industry perspective, as fresh seaweed can directly be used for extraction, avoiding drying which adds significantly to the cost of the process. Life cycle impact assessment of the complete seaweed value chain has been carried out to identify the energy demand and key environmental hotspots. This biorefinery process can be used by industry to improve their processes and utilise the by-products generated efficiently.

Fabrication and Evaluation of Filtration Membranes from Industrial Polymer Waste.

Polyvinylidene fluoride (PVDF) polymers are known for their diverse range of industrial applications and are considered important raw materials for membrane manufacturing. In view of circularity and resource efficiency, the present work mainly deals with the reusability of waste polymer 'gels' produced during the manufacturing of PVDF membranes. Herein, solidified PVDF gels were first prepared from polymer solutions as model waste gels, which were then subsequently used to prepare membranes via the phase inversion process. The structural analysis of fabricated membranes confirmed the retention of molecular integrity even after reprocessing, whereas the morphological analysis showed a symmetric bi-continuous porous structure. The filtration performance of membranes fabricated from waste gels was studied in a crossflow assembly. The results demonstrate the feasibility of gel-derived membranes as potential microfiltration membranes exhibiting a pure water flux of 478 LMH with a mean pore size of ~0.2 µm. To further evaluate industrial applicability, the performance of the membranes was tested in the clarification of industrial wastewater, and the membranes showed good recyclability with about 52% flux recovery. The performance of gel-derived membranes thus demonstrates the recycling of waste polymer gels for improving the sustainability of membrane fabrication processes.

Comparison Study of an Optimized Ultrasound-Based Method versus an Optimized Conventional Method for Agar Extraction, and Protein Co-Extraction, from Gelidium sesquipedale.

Agar is a hydrocolloid found in red seaweeds, which has been of industrial interest over the last century due to its multiple applications in the food, cosmetic, and medical fields. This polysaccharide, extracted by boiling for several hours, is released from the cell wall of red seaweeds. However, the environmental impact coming from the long processing time and the energy required to reach the targeted processing temperature needs to be reduced. In this study, a response surface methodology was employed to optimize both conventional extraction and ultrasound-assisted extractions. Two different models were successfully obtained (R2 = 0.8773 and R2 = 0.7436, respectively). Additionally, a further re-extraction confirmed that more agar could be extracted. Protein was also successfully co-extracted in the seaweed residues. Optimized conditions were obtained for both the extractions and the re-extraction of the two methods (CE: 6 h, 100 °C; and UAE: 1 h, 100% power). Finally, FT-IR characterization demonstrated that the extracts had a similar spectrum to the commercial agar. Compared to commercial samples, the low gel strength of the agar extracts shows that these extracts might have novel and different potential applications.

Biodegradation of Poly (Butylene Succinate) (PBS)/Stearate Modified Magnesium-Aluminium Layered Double Hydroxide Composites under Marine Conditions Prepared via Melt Compounding.

In the present work, polybutylene succinate (PBS)/stearate modified magnesium-aluminium layered double hydroxide (St-Mg-Al LDH) composites were prepared via melt processing and the effect of different loadings of St-Mg-Al LDH on the degradation behaviour of PBS under marine conditions was investigated. The morphological, mechanical and thermal characteristics of the composites were studied using different characterisation techniques. Optical imaging and scanning electron microscopy revealed that the incorporation of St-Mg-Al LDH accelerates the degradation of PBS along with the activity of microorganisms adhered to the composite films. PBS/St-Mg-Al LDH composites are found to have lower thermal degradation temperatures than those of pure PBS. The decrease in thermal stability is correlated with the degradation of PBS due to the catalytic action Mg and Al present in LDH. Tensile and DMA analysis revealed that the addition of St-Mg-Al LDH did not have a significant impact on the mechanical properties of PBS.

Improved Surface Functional and Photocatalytic Properties of Hybrid ZnO-MoS2-Deposited Membrane for Photocatalysis-Assisted Dye Filtration.

The synergistic mechanism of photocatalytic-assisted dye degradation has been demonstrated using a hybrid ZnO-MoS2-deposited photocatalytic membrane (PCM). Few layers of MoS2 sheets were produced using the facile and efficient surfactant-assisted liquid-phase exfoliation method. In this process, hydrophilic moieties of an anionic surfactant were adsorbed on the surface of MoS2, which aided exfoliation and promoted a stable dispersion due to the higher negative zeta potential of the exfoliated MoS2 sheets. Further, the decoration of ZnO on the exfoliated MoS2 sheets offered a bandgap energy reduction to about 2.77 eV, thus achieving an 87.12% degradation of methylene blue (MB) dye within 15 min of near UV-A irradiation (365 nm), as compared with pristine ZnO achieving only 56.89%. The photocatalysis-enhanced membrane filtration studies on the ZnO-MoS2 PCM showed a complete removal of MB dye (~99.95%). The UV-assisted dye degradation on the ZnO-MoS2 PCM offered a reduced membrane resistance, with the permeate flux gradually improving with the increase in the UV-irradiation time. The regeneration of the active ZnO-MoS2 layer also proved to be quite efficient with no compromise in the dye removal efficiency.