ABSTRACT
In this study, we systematically characterized the airborne dust generated from grinding engineered and natural stone products using a laboratory testing system designed and operated to collect representative respirable dust samples. Four stone samples tested included two engineered stones consisting of crystalline silica in a polyester resin matrix (formulations differed with Stones A having up to 90wt% crystalline silica and Stone B up to 50wt% crystalline silica), an engineered stone consisting of recycled glass in a cement matrix (Stone C), and a granite. Aerosol samples were collected by respirable dust samplers, total dust samplers, and a Micro-Orifice Uniform Deposit Impactor. Aerosol samples were analyzed by gravimetric analysis and x-ray diffraction to determine dust generation rates, crystalline silica generation rates, and crystalline silica content. Additionally, bulk dust settled on the floor of the testing system was analyzed for crystalline silica content. Real-time particle size distributions were measured using an Aerodynamic Particle Sizer. All stone types generated similar trimodal lognormal number-weighted particle size distributions during grinding with the most prominent mode at an aerodynamic diameter of about 2.0-2.3 µm, suggesting dust formation from grinding different stones is similar. Bulk dust from Stone C contained no crystalline silica. Bulk dust from Stone A, Stone B, and granite contained 60, 23, and 30wt% crystalline silica, respectively. In Stones A and B, the cristobalite form of crystalline silica was more plentiful than the quartz form. Only the quartz form was detected in granite. The bulk dust, respirable dust, and total dust for each stone had comparable amounts of crystalline silica, suggesting that crystalline silica content in the bulk dust could be representative of that in respirable dust generated during grinding. Granite generated more dust per unit volume of material removed than the engineered stones, which all had similar normalized dust generation rates. Stone A had the highest normalized generation rates of crystalline silica, followed by granite, Stone B, and Stone C (no crystalline silica), which likely leads to the same trend of respirable crystalline silica (RCS) exposure when working with these different stones. Manufacturing and adoption of engineered stone products with formulations such as Stone B or Stone C could potentially lower or eliminate RCS exposure risks. Combining all the effects of dust generation rate, size-dependent silica content, and respirable fraction, the highest normalized generation rate of RCS consistently occurs at 3.2-5.6 µm for all the stones containing crystalline silica. Therefore, removing particles in this size range near the generation sources should be prioritized when developing engineering control measures.
Subject(s)
Air Pollutants, Occupational , Occupational Exposure , Humans , Occupational Exposure/analysis , Dust/analysis , Air Pollutants, Occupational/analysis , Quartz/analysis , Inhalation Exposure/analysis , Silicon Dioxide/analysis , Aerosols/analysisABSTRACT
Artificial countertop materials, including solid surface composites (SSC) and engineered stone (ES) may pose significant pulmonary health risks for workers who manipulate them. These materials have rapidly become popular in the multibillion-dollar countertop industry, rivaling that of natural materials such as granite and marble due to their variety of desirable esthetic qualities and reduced costs. Both SSC and ES consist of a mineral substrate bound together in a polymer matrix. For SSC the mineral is about 70% aluminum trihydrate (ATH) while ES contains up to 95% crystalline silica by weight. Both materials emit airborne dusts when being manipulated with power tools during the fabrication process. Several deaths and dozens of cases of silicosis have been identified worldwide in workers who fabricate ES, while a single case of fatal pulmonary fibrosis has been associated with SCC dust exposure. This review examines the current state of knowledge for both SSC and ES regarding the composition, particle emission characteristics, workplace exposure data, particle constituent toxicity, and possible methods for reducing worker exposure.
Subject(s)
Occupational Exposure , Pulmonary Fibrosis , Silicosis , Humans , Dust , Occupational Exposure/analysis , Silicon Dioxide , LungABSTRACT
We conducted laboratory experiments to investigate a suspected effect of tetrahydrofuran (THF) on quantifying crystalline silica in samples collected from working with engineered stone when THF is used to process samples prior to the X-ray diffraction (XRD) analysis. Two groups of samples from grinding either engineered stone or granite were simultaneously taken from a laboratory testing system, with one group of samples using THF for processing and another group using muffle furnace for ashing. For each stone type, we also tested four levels of respirable dust loading on the samples by varying the grinding time from 1 to 8 min. Statistical analysis of the experimental results on crystalline silica contents of the two groups of samples showed that the difference between the two methods was not significant (P ≥ 0.05) for the granite at all four levels of respirable dust loading and for the engineered stone at the two levels of respirable dust loading greater than 0.5 mg. However, the crystalline silica content from using THF processing was significantly lower (P = 0.001) than that from using muffle furnace ashing for engineered stone when the respirable dust loading levels were less than 0.5 mg. For the engineered stone dust samples with grinding times of 1 and 2 min, the average respirable dust loading was about 0.19 and 0.34 mg, respectively; while the crystalline silica content from using THF processing was 30.9 and 21.5% lower than that from using muffle furnace ashing, respectively. Since most full-shift samples from field assessments in this industry are expected to have respirable dust loading less than 0.5 mg, muffle furnace or radio frequency plasma ashing should be specified as the preferred sample processing method instead of the THF processing method for quantification of crystalline silica when engineered stone is expected to present to avoid artificially reduced silica content values, which are likely caused by the reactions between THF and the resins in engineered stone.
Subject(s)
Air Pollutants, Occupational , Occupational Exposure , Humans , Inhalation Exposure/analysis , Occupational Exposure/analysis , Silicon Dioxide/analysis , Dust/analysis , Furans/analysis , Air Pollutants, Occupational/analysisABSTRACT
This study investigated the inhalation toxicity of the emissions from 3-D printing with acrylonitrile butadiene styrene (ABS) filament using an air-liquid interface (ALI) in vitro model. Primary normal human-derived bronchial epithelial cells (NHBEs) were exposed to ABS filament emissions in an ALI for 4 hours. The mean and mode diameters of ABS emitted particles in the medium were 175 ± 24 and 153 ± 15 nm, respectively. The average particle deposition per surface area of the epithelium was 2.29 × 107 ± 1.47 × 107 particle/cm2, equivalent to an estimated average particle mass of 0.144 ± 0.042 µg/cm2. Results showed exposure of NHBEs to ABS emissions did not significantly affect epithelium integrity, ciliation, mucus production, nor induce cytotoxicity. At 24 hours after the exposure, significant increases in the pro-inflammatory markers IL-12p70, IL-13, IL-15, IFN-γ, TNF-α, IL-17A, VEGF, MCP-1, and MIP-1α were noted in the basolateral cell culture medium of ABS-exposed cells compared to non-exposed chamber control cells. Results obtained from this study correspond with those from our previous in vivo studies, indicating that the increase in inflammatory mediators occur without associated membrane damage. The combination of the exposure chamber and the ALI-based model is promising for assessing 3-D printer emission-induced toxicity.
Subject(s)
Acrylonitrile , Air Pollution, Indoor , Acrylonitrile/toxicity , Air Pollution, Indoor/analysis , Butadienes/toxicity , Epithelial Cells , Humans , Particle Size , Particulate Matter , Printing, Three-Dimensional , Styrene/analysis , Styrene/toxicityABSTRACT
Copper-based preservatives consisting of micronized and nanoscale copper particles have been widely used in applications for wood protection. The widespread use of these preservatives along with the potential release of copper-containing nanoparticles (Cu NPs) during the life cycle of treated wood, has raised concerns over the impacts on the environment and occupational exposure. Along with assessing the potential hazards of these materials, a critical step is determining the chemical and morphological characteristics of the copper species released from copper-treated wood. Therefore, a combination of scanning transmission electron microscopy (STEM) and electron energy-loss spectroscopy (EELS) was utilized to characterize and differentiate the released copper-containing particles based on their structures, sizing, and chemical properties. Airborne wood dust samples were collected during the abrasion and sawing of micronized copper (MC) treated wood in a laboratory testing system. Based on the signature Cu L2,3 edge of EEL spectra, three different copper species (i.e., basic copper carbonate, copper, and copper-wood complex) were identified as major components of the embedded particles in wood dust. In addition, two types of individual Cu NPs consisting of basic copper carbonate and copper were identified. The variation of morphologies and chemical properties of copper-containing particles indicates the importance of copper-wood interactions to determine the formation and distribution of copper species in wood components. Our findings will advance the fundamental understanding of their released forms, potential transformation, and environmental fate during the life cycle.
ABSTRACT
Laboratory tests were conducted to characterize the composition of emissions from sanding Corian®, a solid-surface composite material mainly composed of alumina trihydrate (ATH) and acrylic polymer. Three sandpaper materials (ceramic, silicon carbide, and aluminum oxide) were tested to distinguish the contribution of aluminum-containing dust in the emission from Corian® and sandpaper itself. The result can help identify the main cause of the pulmonary fibrosis from exposure to aluminum-containing dust while sanding Corian®. Airborne dust samples were measured using direct-reading instruments and collected using a Micro-Orifice Uniform Deposit Impactor (MOUDI) for estimating the normalized dust generation rate. The size-classified dust samples from MOUDI were analyzed for elemental aluminum content. Additionally, air samples were analyzed for characterizing methyl methacrylate (MMA). The results from the direct-reading instruments reveal that the size distribution of particulate from sanding Corian® differs from that of sawing Corian®, showing that the size distribution of dust is affected by the fabrication process. The normalized respirable dust generation rate indicates that more respirable dust was generated during sanding Corian® board. However, the use of aluminum oxide sandpaper does not result in a higher aluminum content in the respirable dust from sanding Corian®, suggesting that the aluminum content of the respirable dust is primarily originated from Corian® itself. The generation rates of MMA from sanding did not vary much among all types of sandpapers, and they were much lower than that of sawing, likely due to the higher temperature in the sawing process.
ABSTRACT
BACKGROUND: Fused filament fabrication 3-D printing with acrylonitrile butadiene styrene (ABS) filament emits ultrafine particulates (UFPs) and volatile organic compounds (VOCs). However, the toxicological implications of the emissions generated during 3-D printing have not been fully elucidated. AIM AND METHODS: The goal of this study was to investigate the in vivo toxicity of ABS-emissions from a commercial desktop 3-D printer. Male Sprague Dawley rats were exposed to a single concentration of ABS-emissions or air for 4 hours/day, 4 days/week for five exposure durations (1, 4, 8, 15, and 30 days). At 24 hours after the last exposure, rats were assessed for pulmonary injury, inflammation, and oxidative stress as well as systemic toxicity. RESULTS AND DISCUSSION: 3-D printing generated particulate with average particle mass concentration of 240 ± 90 µg/m³, with an average geometric mean particle mobility diameter of 85 nm (geometric standard deviation = 1.6). The number of macrophages increased significantly at day 15. In bronchoalveolar lavage, IFN-γ and IL-10 were significantly higher at days 1 and 4, with IL-10 levels reaching a peak at day 15 in ABS-exposed rats. Neither pulmonary oxidative stress responses nor histopathological changes of the lungs and nasal passages were found among the treatments. There was an increase in platelets and monocytes in the circulation at day 15. Several serum biomarkers of hepatic and kidney functions were significantly higher at day 1. CONCLUSIONS: At the current experimental conditions applied, it was concluded that the emissions from ABS filament caused minimal transient pulmonary and systemic toxicity.
Subject(s)
Acrylic Resins/toxicity , Air Pollution, Indoor/adverse effects , Butadienes/toxicity , Inhalation Exposure/adverse effects , Particulate Matter/toxicity , Polystyrenes/toxicity , Printing, Three-Dimensional , Respiratory System/drug effects , Volatile Organic Compounds/toxicity , Acrylic Resins/pharmacokinetics , Aerosols , Air Pollution, Indoor/analysis , Animals , Biomarkers/metabolism , Blood Cell Count , Bronchoalveolar Lavage Fluid/chemistry , Butadienes/pharmacokinetics , Cytokines/blood , Male , Microscopy, Electron, Scanning , Oxidative Stress/drug effects , Particle Size , Particulate Matter/analysis , Particulate Matter/pharmacokinetics , Polystyrenes/pharmacokinetics , Rats, Sprague-Dawley , Respiratory System/metabolism , Respiratory System/ultrastructure , Volatile Organic Compounds/analysis , Volatile Organic Compounds/pharmacokineticsABSTRACT
Solid surface composites (SSCs) are a class of popular construction materials composed of aluminum trihydrate and acrylic polymers. Previous investigations have demonstrated that sawing SSC releases substantial airborne dusts, with a number-based geometric mean diameter of 1.05 µm. We reported that in mice, aspiration exposure to airborne SSC dusts induced symptoms of pulmonary inflammation at 24-h postexposure: neutrophilic influx, alveolitis, and increased lactate dehydrogenase (LDH) and pro-inflammatory cytokine levels in lavage fluid. The particles appeared to be poorly cleared, with 81% remaining at 14-day postexposure. The objective of this study was to determine the toxicity specifically of respirable particles on a model of human alveolar macrophages (THP-1). The relative toxicities of subfractions (0.07, 0.66, 1.58, 5.0, and 13.42 µm diameter) of the airborne particles were also determined. THP-1 macrophages were exposed for 24 h to respirable particles from sawing SSC (0, 12.5, 25, 50, or 100 µg/ml) or size-specific fractions (100 µg/ml). Exposure to respirable SSC particles induced THP-1 macrophage toxicity in a dose-dependent manner. Viability was decreased by 15% and 19% after exposure to 50 and 100 µg/ml SSC, respectively, which correlated with increased cell culture supernatant LDH activity by 40% and 70% when compared to control. Reactive oxygen species (ROS) production and inflammatory cytokines were increased in a dose-dependent manner. A size-dependent cytotoxic effect was observed in the cells exposed to subfractions of SSC particles. SSC particles of 0.07, 0.66, and 1.58 µm diameter killed 36%, 17%, and 22% of cells, respectively. These results indicate a potential for cytotoxicity of respirable SSC particles and a relationship between particle size and toxicity, with the smallest fractions appearing to exhibit the greatest toxicity.
Subject(s)
Construction Materials/toxicity , Macrophages, Alveolar/drug effects , Animals , Dust , Humans , In Vitro Techniques , Inhalation Exposure , Macrophages, Alveolar/pathology , Mice , Particle Size , Toxicity TestsABSTRACT
During extrusion of some polymers, fused filament fabrication (FFF) 3-D printers emit billions of particles per minute and numerous organic compounds. The scope of this study was to evaluate FFF 3-D printer emission-induced toxicity in human small airway epithelial cells (SAEC). Emissions were generated from a commercially available 3-D printer inside a chamber, while operating for 1.5â¯h with acrylonitrile butadiene styrene (ABS) or polycarbonate (PC) filaments, and collected in cell culture medium. Characterization of the culture medium revealed that repeat print runs with an identical filament yield various amounts of particles and organic compounds. Mean particle sizes in cell culture medium were 201⯱â¯18â¯nm and 202⯱â¯8â¯nm for PC and ABS, respectively. At 24â¯h post-exposure, both PC and ABS emissions induced a dose dependent significant cytotoxicity, oxidative stress, apoptosis, necrosis, and production of pro-inflammatory cytokines and chemokines in SAEC. Though the emissions may not completely represent all possible exposure scenarios, this study indicate that the FFF could induce toxicological effects. Further studies are needed to quantify the detected chemicals in the emissions and their corresponding toxicological effects.
Subject(s)
Acrylic Resins/toxicity , Butadienes/toxicity , Epithelial Cells/drug effects , Nanoparticles/toxicity , Polycarboxylate Cement/toxicity , Polystyrenes/toxicity , Printing, Three-Dimensional , Respiratory Mucosa/drug effects , Apoptosis/drug effects , Cells, Cultured , Cytokines/metabolism , Dose-Response Relationship, Drug , Epithelial Cells/metabolism , Epithelial Cells/ultrastructure , Humans , Inflammation Mediators/metabolism , Necrosis , Oxidative Stress/drug effects , Particle Size , Respiratory Mucosa/metabolism , Respiratory Mucosa/ultrastructure , Risk Assessment , Time FactorsABSTRACT
Corian®, a solid-surface composite (SSC), is composed of alumina trihydrate and acrylic polymer. The aim of the present study was to examine the pulmonary toxicity attributed to exposure to SSC sawing dust. Male mice were exposed to either phosphate buffer saline (PBS, control), 62.5, 125, 250, 500, or 1000 µg of SSC dust, or 1000 µg silica (positive control) via oropharyngeal aspiration. Body weights were measured for the duration of the study. Bronchoalveolar lavage fluid (BALF) and tissues were collected for analysis at 1 and 14 days post-exposure. Enhanced-darkfield and histopathologic analysis was performed to assess particle distribution and inflammatory responses. BALF cells and inflammatory cytokines were measured. The geometric mean diameter of SSC sawing dust following suspension in PBS was 1.25 µm. BALF analysis indicated that lactate dehydrogenase (LDH) activity, inflammatory cells, and pro-inflammatory cytokines were significantly elevated in the 500 and 1000 µg SSC exposure groups at days 1 and 14, suggesting that exposure to these concentrations of SSC induced inflammatory responses, in some cases to a greater degree than the silica positive control. Histopathology indicated the presence of acute alveolitis at all doses at day 1, which was largely resolved by day 14. Alveolar particle deposition and granulomatous mass formation were observed in all exposure groups at day 14. The SSC particles were poorly cleared, with 81% remaining at the end of the observation period. These findings demonstrate that SSC sawing dust exposure induces pulmonary inflammation and damage that warrants further investigation. Abbreviations: ANOVA: Analysis of Variance; ATH: Alumina Trihydrate; BALF: Bronchoalveolar Lavage Fluid; Dpg: Geometric Mean Diameter; FE-SEM: Field Emission Scanning Electron Microscopy; IACUC: Institutional Animal Care and Use Committee; IFN-γ: Interferon Gamma; IL-1 Β: Interleukin-1 Beta; IL-10: Interleukin-10; IL-12: Interleukin-12; IL-2: Interleukin-2; IL-4: Interleukin-4; IL-5: Interleukin-5; IL-6: Interleukin-6; KC/GRO: Neutrophil-Activating Protein 3; MMAD: Mass Median Aerodynamic Diameter; PBS: Phosphate-Buffered Saline; PEL: Permissible Exposure Limit; PM: Polymorphonuclear Leukocytes; PNOR: Particles Not Otherwise Regulated; SEM/EDX: Scanning Electron Microscope/Energy-Dispersive X-Ray; SSA: Specific Surface Area; SSC: Solid Surface Composite; TNFα: Tumor Necrosis Factor-Alpha; VOC: Volatile Organic Compounds; σg: Geometric Standard Deviation.
Subject(s)
Dust , Lung Diseases/chemically induced , Animals , Bronchoalveolar Lavage Fluid/chemistry , Bronchoalveolar Lavage Fluid/cytology , Construction Materials , Cytokines/chemistry , Cytokines/metabolism , Inflammation/chemically induced , Inhalation Exposure , Male , Mice , Mice, Inbred C57BL , Specific Pathogen-Free OrganismsABSTRACT
Micronized copper azole (MCA) is a lumber treatment improve longevity. In this study, the in vivo response to PM2.5 sanding dust generated from MCA-treated lumber was compared to that of untreated yellow pine (UYP) or soluble copper azole-treated (CA-C) lumber to determine if the MCA was more bioactive than CA-C. Mice were exposed to doses (28, 140, or 280 µg/mouse) of UYP, MCA, or CA-C sanding dust using oropharyngeal aspiration. Bronchoalveolar lavage fluid (BALF) lactate dehydrogenase activity was increased at 1 day post-exposure to 280 µg/mouse of MCA and CA-C compared to UYP. BALF polymorphonuclear cells were increased by MCA and CA-C. There were increases in BALF cytokines in MCA and CA-C-exposed groups at 1 day post-exposure. Lung histopathology indicated inflammation with infiltration of neutrophils and macrophages. Pulmonary responses were more severe in MCA and CA-C-exposed groups at 1 day post-exposure. MCA caused more severe inflammatory responses than CA-C at 1 day post-exposure. These findings suggest that the MCA and CA-C sanding dusts are more bioactive than the UYP sanding dust, and, moreover, the MCA sanding dust is more bioactive in comparison to the CA-C sanding dust. No chronic toxic effects were observed among all observed sanding dusts.
Subject(s)
Copper/toxicity , Inhalation Exposure/adverse effects , Particulate Matter/toxicity , Animals , Bronchoalveolar Lavage Fluid/chemistry , Bronchoalveolar Lavage Fluid/immunology , Copper/analysis , L-Lactate Dehydrogenase/analysis , Lung/pathology , Mice , Toxicity Tests , WoodABSTRACT
We conducted detailed analyses of the composition of emissions from sawing Corian®, a solid surface composite material, in a laboratory testing system. The analyses included the aluminum content of size-selective dust samples, semivolatile organic compounds (SVOCs) in respirable dust samples, and volatile organic compounds (VOCs). The normalized respirable dust generation rate found using a Micro-Orifice Uniform Deposit Impactor was 5.9 milligrams per gram (mg g-1) suggesting that 0.59% of the mass removed from sawing Corian® becomes respirable dust. The alumina trihydrate content of the dust was consistently above 85% in most parts of the respirable size range, verifying an earlier finding that it is the dominant composition of the airborne particles of all sizes, including ultrafine particles. VOC analyses revealed that methyl methacrylate (MMA) was the most abundant compound, with a generation rate of 6.9 mg g-1 (0.69% of the mass removed from sawing Corian® became MMA vapor). The SVOC analysis only found a small amount of MMA (0.55%) in the bulk dust.
Subject(s)
Air Pollutants, Occupational/analysis , Aluminum/analysis , Dust/analysis , Occupational Exposure/analysis , Volatile Organic Compounds/analysis , Aluminum/chemistry , Humans , Particulate Matter/analysisABSTRACT
Fused deposition modeling (FDM™) 3-dimensional printing uses polymer filament to build objects. Some polymer filaments are formulated with additives, though it is unknown if they are released during printing. Three commercially available filaments that contained carbon nanotubes (CNTs) were printed with a desktop FDM™ 3-D printer in a chamber while monitoring total particle number concentration and size distribution. Airborne particles were collected on filters and analyzed using electron microscopy. Carbonyl compounds were identified by mass spectrometry. The elemental carbon content of the bulk CNT-containing filaments was 1.5 to 5.2 wt%. CNT-containing filaments released up to 1010 ultrafine (d < 100 nm) particles/g printed and 106 to 108 respirable (d ~0.5 to 2 µm) particles/g printed. From microscopy, 1% of the emitted respirable polymer particles contained visible CNTs. Carbonyl emissions were observed above the limit of detection (LOD) but were below the limit of quantitation (LOQ). Modeling indicated that, for all filaments, the average proportional lung deposition of CNT-containing polymer particles was 6.5%, 5.7%, and 7.2% for the head airways, tracheobronchiolar, and pulmonary regions, respectively. If CNT-containing polymer particles are hazardous, it would be prudent to control emissions during use of these filaments.
Subject(s)
Imaging, Three-Dimensional , Nanotubes, Carbon , Polymers/chemistry , Environmental Monitoring/methods , Inhalation Exposure , Particulate Matter/analysisABSTRACT
To protect against decay and fungal invasion into the wood, the micronized copper, copper carbonate particles, has been applied in the wood treatment in recent years; however, there is little information on the health risk associated with sanding micronized copper-treated lumber. In this study, wood dust from the sanding of micronized copper azole-treated lumber (MCA) was compared to sanding dust from solubilized copper azole-treated wood (CA-C) and untreated yellow pine (UYP). The test found that sanding MCA released a much higher concentration of nanoparticles than sanding CA-C and UYP, and the particles between about 0.4-2 µm from sanding MCA had the highest percentage of copper. The percentage of copper in the airborne dust from sanding CA-C had a weak dependency on particle size and was lower than that from sanding MCA. Nanoparticles were seen in the MCA PM2.5 particles, while none were detected in the UYP or CA-C. Inductively coupled plasma mass spectrometry (ICP-MS) analysis found that the bulk lumber for MCA and CA-C had relatively equal copper content; however, the PM2.5 particles from sanding the MCA had a higher copper concentration when compared to the PM2.5 particles from sanding UYP or CA-C. The cellular toxicity assays show that exposure of RAW 264.7 macrophages (RAW) to MCA and CA-C wood dust suspensions did not induce cellular toxicity even at the concentration of 200 µg PM2.5 wood dust/mL. Since the copper from the treated wood dust can leach into the wood dust supernatant, the supernatants of MCA, CA-C and UYP wood dusts were subjected to the cellular toxicity assays. The data showed that at the higher concentrations of copper (≥5 µg/ml), both MCA and CA-C supernatants induced cellular toxicity. This study suggests that sanding MCA-treated lumber releases copper nanoparticles and both the MCA and CA-C-treated lumber can release copper, which are potentially related to the observed in vitro toxicity.
Subject(s)
Copper/analysis , Dust/analysis , Wood/chemistry , Animals , Azoles/chemistry , Copper/toxicity , Mice , Nanoparticles/chemistry , Nanoparticles/toxicity , Particle Size , RAW 264.7 CellsABSTRACT
OBJECTIVES: Workers who fabricate stone countertops using hand tools are at risk of silicosis from overexposure to respirable crystalline silica. This study explored the efficacy of simple engineering controls that can be used for dust suppression during use of hand tools by stone countertop fabricators. METHODS: Controlled experiments were conducted to measure whether wet methods and on-tool local exhaust ventilation (LEV) reduced respirable dust (RD) exposures during use of various powered hand tools on quartz-rich engineered stone. RD samples collected during edge grinding with a diamond cup wheel and a silicon carbide abrasive wheel were analyzed gravimetrically as well as by X-ray diffraction to determine silica content. A personal optical aerosol monitor was used simultaneously with the RD samples and also for rapid assessment of controls for polishing, blade cutting, and core drilling. RESULTS: On-tool LEV and sheet-flow-wetting were effective in reducing exposures, especially when used in combination. Sheet-flow-wetting with LEV reduced geometric mean exposures by as much as 95%. However, typical water-spray-wetting on a grinding cup was less effective when combined with LEV than without LEV. Mean silica content of RD samples from grinding operations was 53%, and respirable mass and silica mass were very highly correlated (r = 0.980). Optical concentration measures were moderately well correlated with gravimetric measures (r = 0.817), but on average the optical measures during a single trial using the factory calibration were only one-fifth the simultaneous gravimetric measures. CONCLUSIONS: Sheet-flow-wetting combined with on-tool LEV is an effective engineering control for reducing RD exposures during engineered stone edge grinding and blade cutting. On the other hand, addition of LEV to some water-spray-wetted tools may reduce the effectiveness of the wet method.
Subject(s)
Air Pollutants, Occupational/analysis , Construction Materials , Dust/analysis , Engineering , Inhalation Exposure/analysis , Occupational Exposure/analysis , Quartz/analysis , Engineering/methods , Humans , Inhalation Exposure/prevention & control , Occupational Exposure/prevention & control , Pilot Projects , Silicosis , Ventilation/methods , Wetting AgentsABSTRACT
This article describes the evaluation of the generation rate of respirable dust (GAPS, defined as the mass of respirable dust generated per unit linear length cut) from cutting fiber cement siding using different tools in a laboratory testing system. We used an aerodynamic particle sizer spectrometer (APS) to continuously monitor the real-time size distributions of the dust throughout cutting tests when using a variety of tools, and calculated the generation rate of respirable dust for each testing condition using the size distribution data. The test result verifies that power shears provided an almost dust-free operation with a GAPS of 0.006 g m-1 at the testing condition. For the same power saws, the cuts using saw blades with more teeth generated more respirable dusts. Using the same blade for all four miter saws tested in this study, a positive linear correlation was found between the saws' blade rotating speed and its dust generation rate. In addition, a circular saw running at the highest blade rotating speed of 9068 rpm generated the greatest amount of dust. All the miter saws generated less dust in the 'chopping mode' than in the 'chopping and sliding' mode. For the tested saws, GAPS consistently decreased with the increases of the saw cutting feed rate and the number of board in the stack. All the test results point out that fewer cutting interactions between the saw blade's teeth and the siding board for a unit linear length of cut tend to result in a lower generation rate of respirable dust. These results may help guide optimal operation in practice and future tool development aimed at minimizing dust generation while producing a satisfactory cut.
Subject(s)
Air Pollutants, Occupational/analysis , Construction Materials , Dust/analysis , Inhalation Exposure/analysis , Silicon Dioxide/analysis , Environmental Monitoring/methods , Equipment Design/standards , Humans , Occupational Exposure/analysis , Particle Size , Ventilators, MechanicalABSTRACT
A low-flow miniature differential mobility analyzer (mDMA) has been developed for compact field-portable mobility spectrometers to classify the submicrometer aerosol. The mDMA was designed for an ultra-low aerosol flow rate of 0.05 L/min. At a sheath flow rate of 0.2 L/min, the mDMA's upper size limit was estimated to be about 921 nm. The mDMA has a classification zone of 2.54 cm long, an outer diameter of 2.54 cm, and an inner diameter of 1.778 cm. The design allows low-cost fabrication and easy assembly. Tandem DMA (TDMA) measurements were carried out to evaluate the performance of the mDMA. Its transfer function was described using Stolzenburg's model. The experimentally measured transfer function shows close agreement with the theory. The transmission efficiency was comparable to that of the Knutson-Whitby DMA for particles in the range of 10-1000 nm. The mobility resolution was comparable to that of the TSI 3085 nanoDMA at the same aerosol flow rate. The design features and performance of the mDMA make it suitable for compact field portable mobility size spectrometers for measurement of nanoparticles and submicrometer aerosol.
ABSTRACT
We conducted a laboratory test to characterize dust from cutting Corian(®), a solid-surface composite material, with a circular saw. Air samples were collected using filters and direct-reading instruments in an automatic laboratory testing system. The average mass concentrations of the total and respirable dusts from the filter samples were 4.78±0.01 and 1.52±0.01mg cm(-3), respectively, suggesting about 31.8% mass of the airborne dust from cutting Corian(®) is respirable. Analysis of the metal elements on the filter samples reveals that aluminum hydroxide is likely the dominant component of the airborne dust from cutting Corian(®), with the total airborne and respirable dusts containing 86.0±6.6 and 82.2±4.1% aluminum hydroxide, respectively. The results from the direct-reading instruments confirm that the airborne dust generated from cutting Corian(®) were mainly from the cutting process with very few particles released from the running circular saw alone. The number-based size distribution of the dusts from cutting Corian(®) had a peak for fine particles at 1.05 µm with an average total concentration of 871.9 particles cm(-3), and another peak for ultrafine particles at 11.8nm with an average total concentration of 1.19×10(6) particles cm(-3) The small size and high concentration of the ultrafine particles suggest additional investigation is needed to study their chemical composition and possible contribution to pulmonary effect.
Subject(s)
Air Pollutants, Occupational/analysis , Dust/analysis , Occupational Exposure/analysis , Construction Materials , Environmental Monitoring/methods , Particle SizeABSTRACT
We describe development of a Portable Aerosol Mobility Spectrometer (PAMS) for size distribution measurement of submicrometer aerosol. The spectrometer is designed for use in personal or mobile aerosol characterization studies and measures approximately 22.5 × 22.5 × 15 cm and weighs about 4.5 kg including the battery. PAMS uses electrical mobility technique to measure number-weighted particle size distribution of aerosol in the 10-855 nm range. Aerosol particles are electrically charged using a dual-corona bipolar corona charger, followed by classification in a cylindrical miniature differential mobility analyzer. A condensation particle counter is used to detect and count particles. The mobility classifier was operated at an aerosol flow rate of 0.05 L/min, and at two different user-selectable sheath flows of 0.2 L/min (for wider size range 15-855 nm) and 0.4 L/min (for higher size resolution over the size range of 10.6-436 nm). The instrument was operated in voltage stepping mode to retrieve the size distribution, which took approximately 1-2 minutes, depending on the configuration. Sizing accuracy and resolution were probed and found to be within the 25% limit of NIOSH criterion for direct-reading instruments (NIOSH 2012). Comparison of size distribution measurements from PAMS and other commercial mobility spectrometers showed good agreement. The instrument offers unique measurement capability for on-person or mobile size distribution measurements of ultrafine and nanoparticle aerosol.
ABSTRACT
A laboratory testing system was developed to systematically characterize the dust generation rate and size-dependent crystalline silica content when cutting or shaping silica containing materials. The tests of cutting fiber cement siding in this system verify that it provides high test repeatability, making it suitable for the targeted characterizations. The mass-based size distributions obtained from a gravimetric-based instrument and a direct reading instrument both show bimodal lognormal distributions with a larger mode ~13 µm and another mode <5 µm for the dusts from cutting four different brands of fiber cement siding. The generation rates of respirable dust obtained from the two instruments are comparable, and the results from each instrument are similar for the four brands. The silica content in the airborne dusts, however, strongly depends on the amount of silica used in the respective product. It is also observed that the silica content in the airborne dust from cutting the four brands of fiber cement siding showed the same trend of an increase with the aerodynamic diameter of the dust, approaching the silica content levels found in their respective bulk samples. Combining the results for both the dust size distribution and size-dependent silica content, it is found that most of the respirable crystalline silica (RCS) resides in the dust ~2.5 µm in aerodynamic diameter. These results would help guide the development of specific engineering control measures targeted at lowering workers' exposure to RCS while cutting fiber cement siding. With the high repeatability using the laboratory testing system, the dust generation rate could then be characterized under different operating conditions, and with the deployment of various engineering control measures. This would greatly facilitate the systematic evaluation of the control effectiveness and the selection of the optimal control solutions for field trials.