Carbon Nanotube-, Boron Nitride-, and Graphite-Filled Polyketone Composites for Thermal Energy Management.

In order to improve the thermal conductivity of 30 wt % synthetic graphite (SG)-filled polyketones (POKs), conductive fillers such as multiwall carbon nanotubes (CNTs) and hexagonal boron nitride (BN) were used in this study. Individual and synergistic effects of CNTs and BN on 30 wt % synthetic graphite-filled POK on thermal conductivity were investigated. 1, 2, and 3 wt % CNT loading enhanced the in-plane and through-plane thermal conductivities of POK-30SG by 42, 82, and 124% and 42, 94, and 273%, respectively. 1, 2, and 3 wt % BN loadings enhanced the in-plane thermal conductivity of POK-30SG by 25, 69, and 107% and through-plane thermal conductivity of POK-30SG by 92, 135, and 325%. It was observed that while CNT shows more efficient in-plane thermal conductivity than BN, BN shows more efficient through-plane thermal conductivity. The electrical conductivity value of POK-30SG-1.5BN-1.5CNT was obtained to be 1.0 × 10-5 S/cm, the value of which is higher than that of POK-30SG-1CNT and lower than that of POK-30SG-2CNT. While BN loading led to a higher heat deflection temperature (HDT) than CNT loading, the hybrid fillers of BNT and CNT led to the highest HDT value. Moreover, BN loading led to higher flexural strength and Izod-notched impact strength values than CNT loading.

Improving Flame Retardant Properties of Aliphatic Polyketone (POK)-Based Composites.

The effect of zinc borate (ZB) and high-molecular-weight siloxane (SIL) on flame retardancy, mechanical, and thermal properties of aliphatic polyketone (POK)-containing aluminum diethyl phosphinate (OF) was investigated in this study. Ten wt % OF is sufficient to obtain V0 rating according to the UL94 test. As the weight fraction of OF was increased, the flame retardancy properties and LOI values improved, while the tensile and impact properties decreased. To avoid the degradation in mechanical and impact properties as much as possible and obtain the same and better flame retardancy properties, synergists such as SIL and ZB were used. Flame retardancy of POK-based composites was determined by the limiting oxygen index (LOI) test, UL94 measurement, and cone calorimeter test. The additions of 1 wt % SIL and ZB have not led to a considerable decrease in the tensile strength and impact properties of POK-10OF. While ZB and SIL are very efficient in decreasing the smoke density, ZB is more efficient than SIL in increasing the LOI value of the composite. The addition of 1, 2, and 4 wt % ZB and SIL synergists did not lower their UL94 ratings. Moreover, it can be added that ZB is more efficient than SIL in decreasing the fire growth rate (FIGRA) and maximum average rate of heat emission (MARHE) values. Using OF (10 wt %) and ZB (4 wt %), LOI values higher than 32% and smoke density values lower than 150 were obtained.

Comparison of the Thermal and Mechanical Properties of Poly(phenylene sulfide) and Poly(phenylene sulfide)-Syndiotactic Polystyrene-Based Thermal Conductive Composites.

Syndiotactic polystyrene (SPS) has attracted considerable attention recently due to its high melting temperature, low cost, and relatively low density value. The aim of the study is to reveal whether a blend of PPS and SPS (PPS-SPS) can be used instead of PPS for high thermal stability, high mechanical performance, and high thermal conductive material applications. For this aim, poly(phenylene sulfide)/syndiotactic polystyrene-based carbon-loaded composite materials were prepared using a twin screw extruder. Two carbon-based materials, carbon fiber (CF) and synthetic graphite (SG), were used to improve the mechanical properties and thermal conductivity of the PPS-SPS blends. Through-plane conductivity values of PPS-30SG-10CF and PPS-SPS-30SG-10CF were obtained to be 13.67 and 12.92 W/mK, with densities of 1.55 and 1.50 g/cm3, respectively. It was demonstrated that PPS-SPS blend-based carbon-loaded composites have great potential to be used in thermal management applications with the advantages of relatively low cost and lightweight compared to PPS-based composites.

Investigation of the Fire Performance of Polyamide 6-Based Composites with Halogen-free Flame Retardants and Synergistic Materials.

In this study, halogen-free flame retardants and metal synergist materials were used to enhance the flammability of PA6. PA6-based composites including various fractions of additives were manufactured using a twin-screw extruder and an injection molding machine. Mechanical, thermal, physical, morphological, and flame retardant properties were investigated with several characterization methods. The study aims to meet R22 requirements based on the EN45545 standard for fire protection of railway vehicles, according to which limiting oxygen index (LOI), smoke density, and conventional index of toxicity (CIT) values under HL3 hazard levels have to be min 32%, max 300, and max 1.5, respectively. 15FR-2MH, 15FR-5MH, 15FR-1MH-1ZB, 15FR-1MH-1BOH, and 15FR-1MH-1SIL composites exhibited both the required smoke density, CIT, and LOI values for R22. It can be said that hybrid synergists provide all requirements according to the R22-EN45545 standard. Instead of using 15FR-2MH, 15FR-1MH-1BOH led to a lower smoke density value for PA6.

Characterization​ and ​analysis of ​m​otion ​m​echanism​ of electroactive​ chitosan-based actuator.

In order to analyze the bending mechanism of the electroactive​ chitosan-based actuator, different amounts of poly(diallyldimethylammonium chloride) (PDAD) were incorporated in chitosan solution. The effects of PDAD concentration on electromechanical performance of chitosan actuator were investigated under various excitation voltages. With the incorporation of PDAD into chitosan solution, crosslinked chitosan film acts as an actuator showing a considerable displacement behavior. However it can be noted that higher incorporation of PDAD into chitosan solution decreased the performance of the actuators. Thermal, viscoelastic, and crystallographic properties of the chitosan films were examined by thermogravimetric analysis, dynamic mechanical analysis, and X-ray diffraction analysis, respectively. The effect of incorporation of PDAD in chitosan-based film on morphological properties of chitosan film was determined by scanning electron microscopy. It was observed that the films involving PDAD have larger pore size than the PDAD free film.

Application of carboxymethylcellulose hydrogel based silver nanocomposites on cotton fabrics for antibacterial property.

In this study, fumaric acid (FA) crosslinked carboxymethylcellulose (CMC) hydrogel (CMCF) based silver nanocomposites were coated on cotton fabric for antibacterial property for the first time. The performance of the nanocomposite treated cotton fabric was tested for different mixing times of hydrogel solution, padding times and concentrations of silver. The cotton fabrics treated with CMC hydrogel based silver nanocomposites demonstrated 99.9% reduction for both Staphylococcus aureus (Sa) and Klebsiella pneumonia (Kp). After one cycle washing processes of treated cotton fabric, there is no significant variation observed in antibacterial activity. From SEM and AFM analyses, silver particles in nano-size, homogenously distributed, were observed. The treated samples were also evaluated by tensile strength, thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR) analysis, fluid absorbency properties, and whiteness index. The treatment of cotton fabric with CMCF hydrogel did not affect the whiteness considerably, but increased the absorbency values of cotton.

Preparation of pH- and ionic-strength responsive biodegradable fumaric acid crosslinked carboxymethyl cellulose.

A novel biodegradable sodium carboxymethyl cellulose (NaCMC)-based hydrogel was synthesized by using fumaric acid (FA) as a crosslinking agent at various ratios. Hydrogels (CMCF) were characterized using Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), X-ray diffraction analysis (XRD), scanning electron microscopy (SEM), and atomic force microscopy (AFM). Swelling behaviors of hydrogels were investigated in distilled water, various salt, and pH solutions. The FTIR results indicated the crosslinking between carboxyl groups of FA with hydroxyl group of NaCMC through ester formation. AFM analyses showed that roughness of hydrogel surface decreased with increasing crosslinker concentration. The swelling capacity decreased with an increase in charge of the metal cation (Al(3+)

A natural sorbent, Luffa cylindrica for the removal of a model basic dye.

In this work, application of Luffa cylindrica in malachite green (MG) removal from aqueous solution was studied in a batch system. The effect of contact time, pH and temperature on removal of malachite green was also investigated. By the time pH was increased from 3 to 5, the amount of sorbed malachite green also increased. Beyond the pH value of 5, the amount of sorbed malachite green remains constant. The fits of equilibrium sorption data to Langmuir, Freundlich and Dubinin-Radushkevich equations were investigated. Langmuir isotherm exhibited best fit with the experimental data. Monolayer sorption capacity increased with the increasing of temperature. Sorption kinetic was evaluated by pseudo-first-order, pseudo-second-order, Elovich rate equations and intraparticle diffusion models. It was inferred that sorption follows pseudo-second-order kinetic model. Thermodynamic parameters for sorption process were also found out. Spontaneous and endothermic nature of sorption was obtained due to negative value of free energy (DeltaG(o)) and positive value of enthalpy (DeltaH(o)) changes. FTIR analyses were also conducted to confirm the sorption of malachite green onto L. cylindrica.

Removal of malachite green by using an invasive marine alga Caulerpa racemosa var. cylindracea.

The biosorption of a cationic dye, malachite green oxalate (MG) from aqueous solution onto an invasive marine alga Caulerpa racemosa var. cylindracea (CRC) was investigated at different temperatures (298, 308 and 318 K). The dye adsorption onto CRC was confirmed by FTIR analysis. Equilibrium data were analyzed using Freundlich, Langmuir and Dubinin-Radushkevich (DR) equations. All of the isotherm parameters were calculated. The Freundlich model gave a better conformity than Langmuir equation. The mean free energy values (E) from DR isotherm were also estimated. In order to clarify the sorption kinetic, the fit of pseudo-first-order kinetic model, second-order kinetic model and intraparticle diffusion model were investigated. It was obtained that the biosorption process followed the pseudo-second-order rate kinetics. From thermodynamic studies the free energy changes were found to be -7.078, -9.848 and -10.864 kJ mol(-1) for 298, 308 and 318 K, respectively. This implied the spontaneous nature of biosorption and the type of adsorption as physisorption. Activation energy value for MG sorption (E(a)) was found to be 37.14 kJ mol(-1). It could be also derived that this result supported physisorption as a type of adsorption.

Sorption of malachite green on chitosan bead.

Chitosan bead was synthesized for the removal of a cationic dye malachite green (MG) from aqueous solution. The effects of temperature (303, 313 and 323 K), pH of the solution (2-11) on MG removal was investigated. Preliminary kinetic experiment was carried out up to 480 min. The sorption equilibrium was reached within 5 h (300 min). In order to determine the adsorption capacity, the sorption data were analyzed using linear form of Langmuir and Freundlich equation. Langmuir equation showed higher conformity than Freundlich equation. Ninety-nine percent removal of MG was reached at the optimum pH value of 8. From kinetic experiments, it was obtained that sorption process followed the pseudo-second-order kinetic model. This study showed that chitosan beads can be excellent adsorbents at high pH values. Activation energy value for sorption process was found to be 85.6 kJ mol(-1). This indicates that sorption process can be assumed as chemical process. Due to negative values of Gibbs free energy, sorption process can be considered as a spontaneous. In order to determine the interactions between MG and chitosan bead, FTIR analysis was also conducted.

Application of iron-rich natural clays in Camlica, Turkey for boron sorption from water and its determination by fluorimetric-azomethine-H method.

In this study, iron-rich natural Camlica Bentonites, CB1 and CB2, were used for the sorption of boron in water samples. Boron was determined by newly progressed fluorimetric azomethine-H method. The optimum conditions found using factorial designs are pH 10, 45 degrees C, 0.250 g of clay and 20 mL of sample volume. It was found that 180 min is enough time for the equilibrium state to be reached in boron adsorption. At these conditions, boron sorption percentage was 80% for CB1 and 30% for CB2. The adsorption isotherms are well described by linear Freundlich model. Various geothermal waters in our country were also studied for boron sorption.

Removal of boron from aqueous solution by adsorption on Al2O3 based materials using full factorial design.

This paper aims the adsorption of boron from aqueous solution onto Siral 30 and Pural using 2(3) full factorial design. The effect of individual variables and their interactional effects for boron adsorption were also determined. From the statistical analysis, it is inferred that as pH and temperature increased boron adsorption from aqueous solution decreased. Siral 30 was found to be more efficient adsorbent than Pural. The unimportant factor affecting boron adsorption from aqueous solution was also verified by using Fisher adequacy test. At the 90% confidence level, the type of adsorbent, temperature and type of adsorbent-temperature interaction was effective on boron adsorption from aqueous solution. The experimental results were fitted to the Langmuir, Freundlich and Dubinin-Radushkevich (DR) equations to find out adsorption capacities. In most cases, the results indicate that Freundlich and DR equations are well described with the sorption data. The adsorption capacity values of Siral 30 calculated from Freundlich and DR equation was greater than that of Pural. The thermodynamic parameters were also estimated and the adsorption process was not spontaneous nature.

Equilibrium and kinetics for the sorption of promethazine hydrochloride onto K10 montmorillonite.

This study presents the adsorption of cationic drug, promethazine hydrochloride from aqueous solution onto K10 montmorillonite. The effects of pH and temperature on adsorption process were investigated. Maximum adsorption pH was obtained to be about 7.5. Thermodynamic parameters found in this study depict the exothermic nature of adsorption. The process was favorable and spontaneous. From kinetic studies, it was found that adsorption process obeyed the pseudo-second-order kinetic model. The Langmuir, Freundlich, Dubinin-Radushkevich (DR) models were applied to describe the equilibrium isotherms and the isotherm constants were determined. The fit of the Langmuir and DR models appeared to be good. Physisorption mainly controls the whole adsorption process but chemisorption also shows a particular contribution.

Removal of boron from aqueous solution by clays and modified clays.

In order to increase the adsorption capacities of bentonite, sepiolite, and illite for the removal of boron form aqueous solution, the clay samples were modified by nonylammonium chloride. Specific surface areas of the samples were determined as a result of N2 adsorption-desorption at 77 K using the BET method. X-ray powder diffraction analysis of the clays and modified clays was used to determine the effects of modifying agents on the layer structure of the clays. The surface characterization of clays and modified clay samples was conducted using the FTIR technique before and after the boron adsorption. For the optimization of the adsorption of boron on clays and modified clays, the effect of pH and ionic strength was examined. The results indicate that adsorption of boron can be achieved by regulating pH values in the range of 8-10 and high ionic strength. In order to find the adsorption characteristics, Langmuir, Freundlich, and Dubinin-Radushkevich adsorption isotherms were applied to the adsorption data. The data were well described by Freundlich and Dubinin-Radushkevich adsorption isotherms while the fit of Langmuir equation to adsorption data was poor. It was reached that modification of bentonite and illite with nonylammonium chloride increased the adsorption capacity for boron sorption from aqueous solution.

Equilibrium studies for trimethoprim adsorption on montmorillonite KSF.

In this study, the adsorption of trimethoprim (TMP) on montmorillonite KSF was studied under different conditions (pH, ionic strength, temperature). The results indicate that a pH value of 5.04 is optimum value for the adsorption of TMP on KSF. The adsorption kinetics was interpreted using pseudo-first-order kinetic model, pseudo-second-order kinetic model and intraparticle diffusion model. The pseudo-second-order model provides the best correlation with the experimental data of KSF adsorption. The adsorption data could be fitted with Freundlich, Langmuir and Dubinin-Radushkevich equation to find the characteristic parameters of each model. It was found that linear form of Langmuir isotherm seems to produce a better model than linear form of Freundlich equation. From the Langmuir and Freundlich equation, the adsorption capacity values raised as the solution temperature decreased. From DR isotherm, it was also determined that the type of adsorption can be considered as ion-exchange mechanism. Determination of the thermodynamic parameters DeltaH(0), DeltaS(0) and DeltaG(0) showed that adsorption was spontaneous and exothermic in nature. It was also added that adsorption of TMP by KSF may involve physical adsorption.

Kinetic and thermodynamic studies of boron removal by Siral 5, Siral 40, and Siral 80.

In this study, adsorption of boron onto Siral 5, Siral 40, and Siral 80 samples was studied in a batch system with a function of temperature and contact time. The results of adsorption studies indicate that adsorption process was well described with the Freundlich equation and Dubinin-Radushkevich (DR) equation. The Langmuir model does not appear to fit the adsorption better than Freundlich or DR. It has also been found that the magnitudes of free energies are less than 8 kJ mol(-1) and within the energy range of physical adsorption. The intraparticle diffusion model and pseudo-first-order and pseudo-second-order kinetic model were tested to find out rate constants of adsorption. From kinetic experiments, it is realized that boron adsorption onto Siral samples obeyed the pseudo-second-order kinetic model. The thermodynamic studies showed that adsorption process was not spontaneous nature and endothermic. It could also be added that the randomness increased during the adsorption.