Seasonal toxicity of urban road dust in runoff process-studies in Poland.

Urban road dust (URD) is one of the most important non-point sources of pollution in agglomerations. The aim of this study was to assess the seasonal toxic effects of URD runoff in two regions of Poland. The concentrations of elements in URD and leachate were studied. The impact of pollutants in URD runoff on water organisms was evaluated using Daphtoxkit F and Rotoxkit F (LC50). The acute toxicity tests for crustaceans and rotifers were selected as the response of these taxa reflects the impact on zooplankton, a key component of aquatic ecosystem and the basis of most food webs. The concentrations of elements were found to vary depending on the site, although URD samples collected in Katowice agglomeration (Upper Silesia) had higher values of elements (Mn, Cu, Zn, As) compared to Wroclaw (Lower Silesia). The concentrations of Mn, Zn, As, Cr, and Mg in water-soluble fraction of URD were higher in summer and winter in the Upper Silesia region due to rainwater runoff resulting from traffic, industries, post-industrial waste, and the presence of old heating systems. When comparing the content of elements in the water-soluble fraction between seasons, Zn, As, Cr, and Al concentrations were slightly higher in winter. The highest mortality of Daphnia magna and Brachiouns calyciflorus was observed in URD from both agglomerations in winter. However, the mortality is likely due to the concentration of elements or/and the coexistence of an unknown compound or a synergistic effect of the studied elements. This study highlights the alarming seasonal sources of elements in URD runoff, which will directly enter the food chain and affect the entire ecosystem, and human health.

The use of spider webs in the monitoring of air quality-A review.

Methods for using spider webs as passive air samplers have been developed over recent years and reported in more than a dozen articles. In this article, we present the typical procedures followed when using this new tool and critically review its application in air pollution assessment. To understand the state of research and application of spider webs in this field, we describe some advantages and disadvantages of their use in the analyses of air contaminants. The aim is to summarize the current knowledge on this subject, highlight gaps in the present studies, and arouse the interest of scientists on this issue. The increased effort could result in the standardization of the method at the national and international level. Integr Environ Assess Manag 2023;19:32-44. © 2022 SETAC.

Is Poland at risk of urban road dust? Comparison studies on mutagenicity of dust.

Depopulation concerns many polish cities, with the exception of a few metropolises such as Wroclaw (Lower Silesia) and Katowice (Upper Silesia) where investments are growing and therefore more humans are exposed to urban environmental pollution. Accumulation of toxic substances on road surfaces is a major global challenge requiring methods of assessing risk that initiate the proper management strategies. In this study urban road dust (URD) has been collected at seventeen sites in Lower and Upper Silesia regions in Poland renowned for their elevated level of pollution. The aim of the study was: (i) to determine PAH concentration in URD in both regions with the identification of their possible sources based on diagnostic ratio; (ii) to assess possible mutagenic effects of URD with the application of Ames test (Salmonella assay); (iii) to define a possible carcinogenic risk related to URD in both studied regions. We found that the total PAH content of collected URD samples ranged from 142.4 to 1349.4 ng g-1. The diagnostic ratio of PAHs in URD for all studied sites showed that pyrogenic combustion predominated indicating traffic-related and biomass sources of pollution. The Ames assay, which has never been used in studies of URD in Poland, demonstrated that in both regions, URD samples (from eight sites), were characterised by the highest mutagenicity values. Additionally, Incremental Lifetime Cancer Risk (ILCR) values, based on PAH content only, were between 10 and 6 to 10-4 indicating potential risk of cancer. Reassuming, humans in both agglomerations are exposed to factors or compounds with carcinogenic properties which may have an adverse health effect through the urban road dust mainly due to vehicular traffic, heating systems and industrial activities.

The Comprehensive Health Risk Assessment of Polish Smelters with Ecotoxicological Studies.

Air pollution connected to smelter activity can significantly deteriorate the quality of soil due to the precipitation of rain or simple deposition of the air particulates into the ground. Hence, in this study, we focused on the analysis of the soil which can inform us about the general state of the environment in the area and the possible health hazard for humans. If the top layer of the soil is in bad condition, it can indicate that air pollution in the area is also not in good condition, and the lives of the inhabitants of these areas can be at serious risk. To comprehensively identify the level of contamination in the soils from the areas of Polish smelters, studies of the concentration of potentially toxic elements (PTEs) in the soil were conducted. On the basis of the obtained results, health risk assessment was performed to verify the possible influence on human health. The results showed that the non-carcinogenic risk existed only for Olawa, while the possibility of the carcinogenic risk occurred in all of the studied places. The outcome is very disturbing and certain steps must be undertaken in order to protect the lives of the inhabitants. Additionally, in order to assess the suitability of soils for the cultivation of edible plants, phytotoxicity tests were conducted. The obtained results revealed that in all the studied areas, a visible inhibition of roots and shoots can be observed. The conducted study indicated the most polluted regions and the possible health hazard, and it can provide the general information about the impact of smelters on the environment.

Site environment type - The main factor of urban road dust toxicity?

The main objective of the study was to determine the effects of the water extracts of urban road dust (URD) samples on the growth inhibition and mortality rate of Heterocypris incongruens in various site environment type. We collected 24 samples of the road dust close to highways, main roads, crossroads as well as at other places i.e. residential area, and suburbs. We determined the selected metals (Al, As, Ba, Cd, Co, Cr, Cu, Ga, Mg, Mn, Mo, Ni, Pb, Rb, Sr, Ti, Tl, V and Zn) content of the water extracts of these samples as well as we tested the toxicity of the water extracts of URD samples using a commercial test Ostracodtoxkit F. We observed the lowest values of the growth inhibition of H. incongruens for residential areas and suburbs (<50%). The highest growth inhibition we found for water extracts of URD samples collected at the main roads in the Katowice urban area and crossroads in the urban areas. Although the mortality and growth inhibition of H. incongruens were related to the road traffic emissions it was impossible to clearly relate this finding with the urban site category.

The influence of the Kinesio Taping on selected ultrasonography measurements, and quality of life in patients with rotator cuff lesions.

The assessment of the six-week influence of Kinesio Taping combined with a rehabilitation on selected ultrasonography measurements, the level of disability, and the quality of life in patients with rotator cuff lesions. 60 participants were randomly assigned into a taping group (KT combined with a six-week rehabilitating protocol) and a control group (only rehabilitation protocol). In all patients the following assessments were performed twice: USG, UEFI and NHP questionnaires. In the examination of the subacromial space and the subacromial bursa in the taping group, no statistical significance was observed. A statistically significant change in the thickness of the muscles was obtained only for the thickness of the infraspinatus in the taping group. A statistically significant change was obtained in the assessment of tendinopathy only for the supraspinatus muscle in both groups. Within both groups a statistically significant difference was observed in the average UEFI and NHP scores; however, the differences in the scores obtained between the groups were not statistically significant. The use of KT with a rehabilitation program did not yield statistically significantly better results in the improvement of selected shoulder region indicators, the function of the upper limb and the quality of life.

Effects of polystyrene diet on Tenebrio molitor larval growth, development and survival: Dynamic Energy Budget (DEB) model analysis.

The presence of polystyrene (PS) waste increases constantly. Styrofoam, the most popular form of PS, is one of the major plastic pollutants in the environment. An efficient and environmentally friendly method of PS recycling is still needed. The biodegradation of PS by insects has been presented by researchers as a promising alternative to chemical, mechanical and thermal methods. The main aim of this study was to assess the survival, growth, and development of yellow mealworms (the larvae of Tenebrio molitor) fed with PS to determine if the insects are able to use PS as a source of mass and energy. The Dynamic Energy Budget (DEB) model was used to analyze the effects of food type on the growth trajectory and metabolism of tested organisms. We investigated five possible modes of influence of PS diet on DEB model parameters including a decrease of food availability, an increase in somatic maintenance power, an increase in costs for structure, allocation of energy, and a decrease in somatic maintenance power. Our results show that changes in the development of larvae fed with PS are mainly caused by a decrease in reserves density and reaction of the organism to the insufficient food supply. The inability or difficulty in completing the life cycle of T. molitor larvae fed with PS raises doubts about the use of mealworms as an effective technology for utilizing polystyrene.

A comprehensive assessment of microbiome diversity in Tenebrio molitor fed with polystyrene waste.

Recently it was demonstrated that mealworm (Tenebrio molitor) larvae consume and biodegrade polystyrene. Thus, in this study a breeding investigation with various types of polystyrene was performed to follow the changes in the gut microbiome diversity. Polystyrene used for packaging purposes (PSp) and expanded polystyrene (EPS) were perceived as more favorable and attacked more frequently by mealworms compared to raw polystyrene (PS) and material commercially available for parcels (PSp). Although our studies showed that larvae could bite and chew selected materials, they are not able to degrade and use them for consumption purposes. In a next-generation sequencing experiment, among all samples, seven classes, Gammaproteobacteria, Bacilli, Clostridia, Acidobacteria, Actinobacteria, Alphaproteobacteria and Flavobacteria, were indicated as the most abundant, whereas the predominant genera were Enterobacter, Lactococcus and Enterococcus. Additionally, we isolated three bacteria strains able to use diverse types of bioplastic as a sole carbon source. The strains with biodegradable activity against bioplastic were identified as species of the genera Klebsiella, Pseudomonas and Serratia. The presence of a bacterial strain able to degrade bioplastic may suggest a potential niche for further investigations.

Prediction of short-term newborn infectious morbidity based on maternal characteristics in patients with PPROM and Ureaplasma species infection.

OBJECTIVES: Preterm premature rupture of membranes (PPROM) complicates about 5% of pregnancies. Ureaplasma species is the most common pathogen found in the amniotic fluid in pregnancieneonatal outcome. The aim of the following study was to evaluate the impact of colonization with the Ureaplasma spp. on pregnant women with PPROM, coin fection with different microorganisms, and antimicrobial treatment on neonatal outcome. MATERIAL AND METHODS: The study included 30 women with PPROM hospitalized in Division of Reproduction in s complicated by PPROM. It is speculated that it requires a coin fection to produce unfavorable Poznan's K. Marcinkowski University of Medical Sciences. Swabs from cenvical canal were obtained for the identifidation of bacterial and ureaplasma tic infections by culture and POR. RESULTS: The presence of any infection during the pregnancy a fter PP ROM was con firmed in 22 patients (Ureaplasma spp. in 12 patients, coin fection in 10 women). The cure rate for Ureaplasma species and other infections was 17% (2/12 patients) and 23% (5/22 patients), respectively There was no correlation between Ureaplasma species infection, coin fection, and cure status with the infection in the newborn. The PPROM to delivery duration also did not affect the newborn infection status. A negative relationship with leukocyte level was detected in patient with newborn infection. CONCLUSIONS: The presence of colonization with Ureaplasma species is not attributable to neonatal short-term morbidity The evaluation of maternal biochemical and microbiological data, regardless of the duration of the pregnancy after PPROM or the cure status, does not add any insight into the newborn infection status.

[Concentration of pro-inflammatory interleukins in cervical secretions of women with PROM and in the umbilical cord blood of their newborns]. / Analiza stezenia prozapalnych interleukin w wydzielinie szyjkowej kobiet z PROM i we krwi pepowinowej ich noworodków.

OBJECTIVES: The aim of the study was to analyze the levels of pro-inflammatory interleukins in cervical secretions of women with PROM, depending on Ureaplasma spp. infection and the time elapsed since the rupture of the membranes, and to correlate their concentration in cervical secretions and in cord blood of the newborns. MATERIAL AND METHODS: The study included 30 women with PROM between 24 and 33+6 weeks of gestation. Cervical swabs from women with confirmed rupture of membranes taken at certain intervals and umbilical cord blood of their newborns constituted the study material. Cervical secretions were evaluated microbiologically and by the PCR method. Concentrations of IL-6, IL-19, IL-10 and TNF-α were analyzed by ELISA. RESULTS: Ureaplasma spp. were the most frequently isolated microorganisms in cervical secretions of women with PROM. Secretion of interleukins in the cervix was not influenced by time elapsed since the PROM. Comparison of interleukin levels in cord blood of newborns born to mothers with and without Ureaplasma spp infection revealed significantly higher levels of IL-6 in the case of Ureaplasma spp. A positive correlation between IL-6 and TNF-α levels in cervical secretions and in cord blood of mothers with PROM and Ureaplasma spp. was detected. CONCLUSIONS: 1. Cervical culture method appears to be sufficient for detecting Ureaplasma spp. 2. Pro-inflammatory interleukins, especially IL-6, obtained by non-invasive methods can be used to predict fetal inflammatory response.

Motion and interaction of aspirin crystals at aqueous-air interfaces.

Small-molecule amphiphiles such as aspirin have unique properties arising from a combination of an aromatic hydrophobic part and a hydrophilic part. We show that crystals of aspirin are capable of generating convective flows at the air-aqueous interface from both Marangoni effects (through weak surface activity) and capillarity (surface deformations). The flow-driven motion of millimeter-sized crystals was found to depend on the presence of other ions in solution as well as the distance and orientation of the crystals. The interactions lead to the formation of groups of two or more crystals that also underwent motion. The convective flows created by small amphiphile crystals might be exploited in the dynamic self-organization of particles at interfaces.

pH wave-front propagation in the urea-urease reaction.

The urease-catalyzed hydrolysis of urea displays feedback that results in a switch from acid (pH ~3) to base (pH ~9) after a controllable period of time (from 10 to >5000 s). Here we show that the spatially distributed reaction can support pH wave fronts propagating with a speed of the order of 0.1-1 mm min(-1). The experimental results were reproduced qualitatively in reaction-diffusion simulations including a Michaelis-Menten expression for the urease reaction with a bell-shaped rate-pH dependence. However, this model fails to predict that at lower enzyme concentrations, the unstirred reaction does not always support fronts when the well-stirred reaction still rapidly switches to high pH.

Base-catalyzed feedback in the urea-urease reaction.

The bell-shaped rate-pH curve coupled to production of base in the urea-urease reaction was utilized to give feedback-driven behavior: an acid-to-base pH clock (a kinetic switch), bistability and hysteresis between an acid/base state when the initial pH was adjusted by a strong acid, and aperiodic pH oscillations when the initial pH was adjusted by a weak acid in an open reactor. A simple model of the reaction reproduced most of the experimental results and provided insight into the role of self-buffering in the dynamics. This reaction suggests new possibilities in the development of biocompatible feedback to couple to pH-sensitive processes for bioinspired applications in medicine, engineering, or materials science.

Comparison of the utility of five commercial kits for extraction of DNA from Aspergillus fumigatus spores.

The aim of this study was to compare the efficiency of DNA extraction from water as well as from blood samples spiked with A. fumigatus spores, using selected commercial kits. Extraction of DNA according to manufacturer's protocols was preceded by blood cells lysis and disruption of fungal cells by enzymatic digestion or bead beating. The efficiency of DNA extraction was measured by PCR using Aspergillus-specific primers and SYBR Green I dye or TaqMan probes targeting 28S rRNA gene. All methods allowed the detection of Aspergillus at the lowest tested density of water suspensions of spores (10¹ cells/ml). The highest DNA yield was obtained using the ZR Fungal/Bacterial DNA kit, YeastStar Genomic DNA kit, and QIAamp DNA Mini kit with mechanical cell disruption. The ZR Fungal/Bacterial DNA and YeastStar kits showed the highest sensitivity in examination of blood samples spiked with Aspergillus (100 % for the detection of 10² spores and 75 % for 10¹ spores). Recently, the enzymatic method ceased to be recommended for examination of blood samples for Aspergillus, thus ZR Fungal/Bacterial DNA kit and QIAamp DNA Mini kit with mechanical cell disruption could be used for extraction of Aspergillus DNA from clinical samples.

Polyhydroxybutyrate synthesis in transgenic flax.

Flax (Linum usitatissimum L.) is an annual plant species widely cultivated in temperate climates for bast fibres and linseed oil. Apart from traditional textile use, the fibres are fast becoming an integral part of new composite materials utilized in automobile and constructive industry. Especially attractive for environmental safety demands are biodegradable and renewable biocomposities based on polyhydroxybutyrate (PHB) polymer as a matrix and reinforced with the flax fibres. Manufacturing of PHB by bacteria fermentation is however substantially more expansive as compared to technologies producing conventional plastics. We report for the first time generation of transgenic plants which produce both components of flax/PHB composites, i.e. the fibres and the thermoplastic matrix in the same plant organ of a crop. The flax (cv. Nike) plants were transformed using constructs bearing either single cDNA, encoding the beta-ketothiolase enzyme (C plants), or all three of the genes necessary for poly-beta-hydroxybutyrate (PHB) synthesis (M plants). Both constructs contained a plastidial targeting sequence. The amount of PHB produced by the transgenic plants was up to over 70-fold higher than in wild-type plants, when analysed using the gas chromatography/mass spectrometry (GC-MS method). The PHB accumulation in plastids caused change both in their shape and size. The use of a stem-specific promoter for transgene expression protected the transgenic plant from growth retardation and also provided higher PHB synthesis than in the case of constructs governed by the 35S CaMV constitutive promoter. None toxic effects that could lead to stunted growth or the loss of fertility were observed, when 14-3-3 promoter was used as the stem-specific. Significant modifications in stem mechanical properties were accompanied to the PHB accumulation in growing cell of fibres in the transgenic plants. The Young's modulus E, the average measure of stem tissues resistance to tensile loads increased up to twice in M plants as compared to a single gene transformed ones. However, a wide range of E values, from 24.1 to 54.4 MPa, was observed in dependence of tested strain. Potential commercial significance of the genetic manipulation approach enabling synthesis of thermoplastic in crops cultivated for fibres is discussed.