CuCl2/FeCl3 Bimetallic Photocatalyst for Sustainable Ethylene Production from Ethanol via Recoverable Redox Cycles.

Photocatalytic conversions of ethanol to valuable chemicals are significant organic synthesis reactions. Herein, we developed a CuCl2/FeCl3 bimetallic photocatalyst for sustainable dehydration of ethanol to ethylene by recoverable redox cycles. The selectivity of ethylene was 98.3% for CuCl2/FeCl3, which is much higher than that of CuCl2 (34.5%) and FeCl3 (86.5%). Due to the ligand-to-metal charge transfer (LMCT) process involved in generating the liquid products, the CuCl2/FeCl3 catalyst will be reduced to CuCl/FeCl2. Oxygen (O2) is required for the recovery of CuCl2/FeCl3 to avoid exhaustion. The soluble Fe3+/Fe2+ redox species deliver catalyst regeneration properties more efficiently than single metal couples, making a series of redox reactions (Cu2+/Cu+, Fe3+/Fe2+, and O2/ethanol couples) recyclable with synergistic effects. A flow reactor was designed to facilitate the continuous production of ethylene. The understanding of bimetallic synergism and consecutive reactions promotes the industrial application process of photocatalytic organic reactions.

Multifunctionally Reusing Waste Solder to Prepare Highly Efficient Sn-Pb Perovskite Solar Cells.

The preparation of perovskite components (PbI2 and SnI2 ) using waste materials is of great significance for the commercialization of perovskite solar cells (PSCs). However, this goal is difficult to achieve due to the purity of the recovered products and the easy oxidation of Sn2+ . Here, a simple one-step synthetic process to convert waste Sn-Pb solder into SnI2 /PbI2 and then applied as-prepared SnI2 /PbI2 to PSCs for high additional value is adopted. During fabrication, Sn-Pb waste solder is also employed to serve as a reducing agent to reduce the Sn4+ in Sn-Pb mixed narrow perovskite precursor and hence remove the deep trap states in perovskite. The target PSCs achieved an efficiency of 21.04%, which is better than the efficiency of the device with commercial SnI2 /PbI2 (20.10%). Meanwhile, the target PSC maintained an initial efficiency of 80% even after 800 h under continuous illumination, which is significantly better than commercial devices. In addition, the method achieved a recovery rate of 90.12% for Sn-Pb waste solder, with a lab-grade purity (over 99.8%) for SnI2 /PbI2 , and the cost of perovskite active layer reduced to 39.81% through this recycling strategy through calculation.

Advances in the Application of Perovskite Materials.

Nowadays, the soar of photovoltaic performance of perovskite solar cells has set off a fever in the study of metal halide perovskite materials. The excellent optoelectronic properties and defect tolerance feature allow metal halide perovskite to be employed in a wide variety of applications. This article provides a holistic review over the current progress and future prospects of metal halide perovskite materials in representative promising applications, including traditional optoelectronic devices (solar cells, light-emitting diodes, photodetectors, lasers), and cutting-edge technologies in terms of neuromorphic devices (artificial synapses and memristors) and pressure-induced emission. This review highlights the fundamentals, the current progress and the remaining challenges for each application, aiming to provide a comprehensive overview of the development status and a navigation of future research for metal halide perovskite materials and devices.

Nanograin-Boundary-Abundant Cu2O-Cu Nanocubes with High C2+ Selectivity and Good Stability during Electrochemical CO2 Reduction at a Current Density of 500 mA/cm2.

Surface and interface engineering, especially the creation of abundant Cu0/Cu+ interfaces and nanograin boundaries, is known to facilitate C2+ production during electrochemical CO2 reductions over copper-based catalysts. However, precisely controlling the favorable nanograin boundaries with surface structures (e.g., Cu(100) facets and Cu[n(100)×(110)] step sites) and simultaneously stabilizing Cu0/Cu+ interfaces is challenging, since Cu+ species are highly susceptible to be reduced into bulk metallic Cu at high current densities. Thus, an in-depth understanding of the structure evolution of the Cu-based catalysts under realistic CO2RR conditions is imperative, including the formation and stabilization of nanograin boundaries and Cu0/Cu+ interfaces. Herein we demonstrate that the well-controlled thermal reduction of Cu2O nanocubes under a CO atmosphere yields a remarkably stable Cu2O-Cu nanocube hybrid catalyst (Cu2O(CO)) possessing a high density of Cu0/Cu+ interfaces, abundant nanograin boundaries with Cu(100) facets, and Cu[n(100)×(110)] step sites. The Cu2O(CO) electrocatalyst delivered a high C2+ Faradaic efficiency of 77.4% (56.6% for ethylene) during the CO2RR under an industrial current density of 500 mA/cm2. Spectroscopic characterizations and morphological evolution studies, together with in situ time-resolved attenuated total reflection-surface enhanced infrared absorption spectroscopy (ATR-SEIRAS) studies, established that the morphology and Cu0/Cu+ interfacial sites in the as-prepared Cu2O(CO) catalyst were preserved under high polarization and high current densities due to the nanograin-boundary-abundant structure. Furthermore, the abundant Cu0/Cu+ interfacial sites on the Cu2O(CO) catalyst acted to increase the *CO adsorption density, thereby increasing the opportunity for C-C coupling reactions, leading to a high C2+ selectivity.

CeO2/Cu2O/Cu Tandem Interfaces for Efficient Water-Gas Shift Reaction Catalysis.

Metal-oxide interfaces on Cu-based catalysts play very important roles in the low-temperature water-gas shift reaction (LT-WGSR). However, developing catalysts with abundant, active, and robust Cu-metal oxide interfaces under LT-WGSR conditions remains challenging. Herein, we report the successful development of an inverse copper-ceria catalyst (Cu@CeO2), which exhibited very high efficiency for the LT-WGSR. At a reaction temperature of 250 °C, the LT-WGSR activity of the Cu@CeO2 catalyst was about three times higher than that of a pristine Cu catalyst without CeO2. Comprehensive quasi-in situ structural characterizations indicated that the Cu@CeO2 catalyst was rich in CeO2/Cu2O/Cu tandem interfaces. Reaction kinetics studies and density functional theory (DFT) calculations revealed that the Cu+/Cu0 interfaces were the active sites for the LT-WGSR, while adjacent CeO2 nanoparticles play a key role in activating H2O and stabilizing the Cu+/Cu0 interfaces. Our study highlights the role of the CeO2/Cu2O/Cu tandem interface in regulating catalyst activity and stability, thus contributing to the development of improved Cu-based catalysts for the LT-WGSR.

Reversible Stacking of 2D ZnIn2 S4 Atomic Layers for Enhanced Photocatalytic Hydrogen Evolution.

It is technically challenging to reversibly tune the layer number of 2D materials in the solution. Herein, a facile concentration modulation strategy is demonstrated to reversibly tailor the aggregation state of 2D ZnIn2 S4 (ZIS) atomic layers, and they are implemented for effective photocatalytic hydrogen (H2 ) evolution. By adjusting the colloidal concentration of ZIS (ZIS-X, X = 0.09, 0.25, or 3.0 mg mL-1 ), ZIS atomic layers exhibit the significant aggregation of (006) facet stacking in the solution, leading to the bandgap shift from 3.21 to 2.66 eV. The colloidal stacked layers are further assembled into hollow microsphere after freeze-drying the solution into solid powders, which can be redispersed into colloidal solution with reversibility. The photocatalytic hydrogen evolution of ZIS-X colloids is evaluated, and the slightly aggregated ZIS-0.25 displays the enhanced photocatalytic H2 evolution rates (1.11 µmol m-2 h-1 ). The charge-transfer/recombination dynamics are characterized by time-resolved photoluminescence (TRPL) spectroscopy, and ZIS-0.25 displays the longest lifetime (5.55 µs), consistent with the best photocatalytic performance. This work provides a facile, consecutive, and reversible strategy for regulating the photo-electrochemical properties of 2D ZIS, which is beneficial for efficient solar energy conversion.

Strain-Engineering of Mesoporous Cs3 Bi2 Br9 /BiVO4 S-Scheme Heterojunction for Efficient CO2 Photoreduction.

Slow charge kinetics and unfavorable CO2 adsorption/activation strongly inhibit CO2 photoreduction. In this study, a strain-engineered Cs3 Bi2 Br9 /hierarchically porous BiVO4 (s-CBB/HP-BVO) heterojunction with improved charge separation and tailored CO2 adsorption/activation capability is developed. Density functional theory calculations suggest that the presence of tensile strain in Cs3 Bi2 Br9 can significantly downshift the p-band center of the active Bi atoms, which enhances the adsorption/activation of inert CO2 . Meanwhile, in situ irradiation X-ray photoelectron spectroscopy and electron spin resonance confirm that efficient charge transfer occurs in s-CBB/HP-BVO following an S-scheme with built-in electric field acceleration. Therefore, the well-designed s-CBB/HP-BVO heterojunction exhibits a boosted photocatalytic activity, with a total electron consumption rate of 70.63 µmol g-1 h-1 , and 79.66% selectivity of CO production. Additionally, in situ diffuse reflectance infrared Fourier transform spectroscopy reveals that CO2 photoreduction undergoes a formaldehyde-mediated reaction process. This work provides insight into strain engineering to improve the photocatalytic performance of halide perovskite.

Additive-Stabilized Emission Centers for Blue Perovskite Light-Emitting Diodes.

The performance of the blue perovskite light-emitting diodes (PeLEDs) is limited by the low photoluminescence quantum yields (PLQYs) and the unstable emission centers. In this work, we incorporate sodium bromide and acesulfame potassium into a quasi-2D perovskite to control the dimension distribution and promote the PLQYs. Benefiting from the efficient energy cascade channel and passivation, the sky-blue PeLED has an external quantum efficiency of 9.7% and no shift of the electroluminescence center under operation voltages from 4 to 8 V. Moreover, the half lifetime of the devices reaches 325 s, 3.3 times that of control devices without additives. This work provides new insights into enhancing the performance of blue PeLEDs.

Self-Generated Buried Submicrocavities for High-Performance Near-Infrared Perovskite Light-Emitting Diode.

Embedding submicrocavities is an effective approach to improve the light out-coupling efficiency (LOCE) for planar perovskite light-emitting diodes (PeLEDs). In this work, we employ phenethylammonium iodide (PEAI) to trigger the Ostwald ripening for the downward recrystallization of perovskite, resulting in spontaneous formation of buried submicrocavities as light output coupler. The simulation suggests the buried submicrocavities can improve the LOCE from 26.8 to 36.2% for near-infrared light. Therefore, PeLED yields peak external quantum efficiency (EQE) increasing from 17.3% at current density of 114 mA cm-2 to 25.5% at current density of 109 mA cm-2 and a radiance increasing from 109 to 487 W sr-1 m-2 with low rolling-off. The turn-on voltage decreased from 1.25 to 1.15 V at 0.1 W sr-1 m-2. Besides, downward recrystallization process slightly reduces the trap density from 8.90 × 1015 to 7.27 × 1015 cm-3. This work provides a self-assembly method to integrate buried output coupler for boosting the performance of PeLEDs.

Atomic-Interface Effect of Single-Atom Ru/CoOx for Selective Electrooxidation of 5-Hydroxymethylfurfural.

The development of single-atom catalysts with effective interfaces for biomass conversion is a promising but challenging research area. In this study, a Ru1/CoOx catalyst was successfully fabricated with the impregnation method, which featured Ru single atoms on a cobalt oxide substrate. The Ru1/CoOx catalyst showed superior performance in the selective electrooxidation of 5-hydroxymethylfurfural (HMF) to produce 2,5-furandicarboxylic acid (FDCA), a high value-added product. The introduction of Ru single atoms with an ultralow loading of ∼0.5 wt % was revealed to accelerate the electroredox of Co2+/Co3+/Co4+ and improve the intrinsic activity of the CoOx substrate with an FDCA selectivity of 76.5%, which is better than that of the pristine CoOx electrocatalysts (62.7%). The interfacial synergistic effect of the Ru1/CoOx interface clarified that Ru single atoms can enhance the adsorption of HMF at the Ru1/CoOx interface, which promoted the rate-determining step of the selective C-H bond activation for FDCA production. This finding provides valuable insights into the rational design of single-atom catalysts with functional interfaces for biomass upgrading.

CuC(O) Interfaces Deliver Remarkable Selectivity and Stability for CO2 Reduction to C2+ Products at Industrial Current Density of 500 mA cm-2.

The electrocatalytic CO2 reduction reaction (CO2 RR) is an attractive technology for CO2 valorization and high-density electrical energy storage. Achieving a high selectivity to C2+ products, especially ethylene, during CO2 RR at high current densities (>500 mA cm-2 ) is a prized goal of current research, though remains technically very challenging. Herein, it is demonstrated that the surface and interfacial structures of Cu catalysts, and the solid-gas-liquid interfaces on gas-diffusion electrode (GDE) in CO2 reduction flow cells can be modulated to allow efficient CO2 RR to C2+ products. This approach uses the in situ electrochemical reduction of a CuO nanosheet/graphene oxide dots (CuOC(O)) hybrid. Owing to abundant CuOC interfaces in the CuOC(O) hybrid, the CuO nanosheets are topologically and selectively transformed into metallic Cu nanosheets exposing Cu(100) facets, Cu(110) facets, Cu[n(100) × (110)] step sites, and Cu+ /Cu0 interfaces during the electroreduction step, the faradaic efficiencie (FE) to C2+ hydrocarbons was reached as high as 77.4% (FEethylene  ≈ 60%) at 500 mA cm-2 . In situ infrared spectroscopy and DFT simulations demonstrate that abundant Cu+ species and Cu0 /Cu+ interfaces in the reduced CuOC(O) catalyst improve the adsorption and surface coverage of *CO on the Cu catalyst, thus facilitating CC coupling reactions.

A Bifunctional Carbazide Additive For Durable CsSnI3 Perovskite Solar Cells.

Inorganic CsSnI3 with low toxicity and a narrow bandgap is a promising photovoltaic material. However, the performance of CsSnI3 perovskite solar cells (PSCs) is much lower than that of Pb-based and hybrid Sn-based (e.g., CsPbX3 and CH(NH2 )2 SnX3 ) PSCs, which may be attributed to its poor film-forming property and the deep traps induced by Sn4+ . Here, a bifunctional additive carbazide (CBZ) is adapted to deposit a pinhole-free film and remove the deep traps via two-step annealing. The lone electrons of the NH2 and CO units in CBZ can coordinate with Sn2+ to form a dense film with large grains during the phase transition at 80 °C. The decomposition of CBZ can reduce Sn4+ to Sn2+ during annealing at 150 °C to remove the deep traps. Compared with the control device (4.12%), the maximum efficiency of the CsSnI3 :CBZ PSC reaches 11.21%, which is the highest efficiency of CsSnI3 PSC reported to date. A certified efficiency of 10.90% is obtained by an independent photovoltaic testing laboratory. In addition, the unsealed CsSnI3 :CBZ devices maintain initial efficiencies of ≈100%, 90%, and 80% under an inert atmosphere (60 days), standard maximum power point tracking (650 h at 65 °C), and ambient air (100 h), respectively.

Photodehydration of Ethanol Mediated by CuCl2-Ethanol Complex.

Biomass ethanol is regarded as a renewable resource but it is not economically viable to transform it to high-value industrial chemicals at present. Herein, a simple, green, and low-cost CuCl2-ethanol complex is reported for ethanol dehydration to produce ethylene and acetal simultaneously with high selectivity under sunlight irradiation. Under N2 atmosphere, the generation rates of ethylene and acetal were 165 and 3672 µmol g-1 h-1, accounting for 100% in gas products and 97% in liquid products, respectively. An outstanding apparent quantum yield of 13.2% (365 nm) and the maximum conversion rate of 32% were achieved. The dehydration reactions start from the photoexcited CuCl2-ethanol complex, and then go through the energy transfer (EnT) and ligand to metal charge transfer (LMCT) mechanisms to produce ethylene and acetal, respectively. The formation energies of the CuCl2-ethanol complex and the key intermediate radicals (e.g., ·OH, CH3CH2·, and CH3CH2O·) were validated to clarify the mechanisms. Different from previous CuCl2-based oxidation and addition reactions, this work is anticipated to supply new insights into the dehydration reaction of ethanol to produce useful chemical feedstocks.

High Efficiency Near-Infrared Perovskite Light Emitting Diodes With Reduced Rolling-Off by Surface Post-Treatment.

The rolling-off phenomenon of device efficiency at high current density caused by quenching of luminescence in perovskite light-emitting diodes (PeLED) is challenging to be solved. Here, 2-amino-5-iodopyrazine (AIPZ) is dissolved in a mixed solvent of chlorobenzene (CB)/isopropanol (IPA) (7:3 volume ratio) for surface post-treatment of FAPbI3 perovskite film. The interaction of AIPZ and perovskite surface not only balances the charge injection but also passivates defects to enhance radiative recombination in PeLED. Therefore, the PeLED champion yields peak external quantum efficiency reaching 23.2% at the current density of 45 mA cm-2 with a radiance brightness of 290 W sr-1 m-2 . More importantly, the rolling-off of device efficiency is significantly reduced. The lowest rolling-off devices can maintain 80% of peak EQE (22.1%) at a high current density of 460 mA cm-2 , whereas the control device only retains 25% of the peak EQE value. This work provides an effective strategy to improve performance and reduce the EQE rolling-off of PeLED for practical application.

Reexamining the Post-Treatment Effects on Perovskite Solar Cells: Passivation and Chloride Redistribution.

Post-treatment is an essential passivation step for the state-of-the-art perovskite solar cells (PSCs) but the additional role is not yet exploited. In this work, perovskite film is fabricated under ambient air with wide humidity window and identify that chloride redistribution induced by post-treatment plays an important role in high performance. The chlorine/iodine ratio on the perovskite surface increases from 0.037 to 0.439 after cyclohexylmethylammonium iodide (CHMAI) treatment and the PSCs deliver a champion power conversion efficiency (PCE) of 24.42% (certificated 23.60%). The maximum external quantum efficiency of electroluminescence (EQEEL ) reaches to 10.84% with a radiance of 170 W sr-1  m-2 , forming the reciprocity relation between EQEEL and nonradiative open-circuit voltage loss (86.0 mV). After thermal annealing, 2D component of perovskite will increase while chloride decline, leading to improved photovoltage but reduced fill factor. Hence, it distinguishes that chloride enrichment can improve charge transport/recombination simultaneously and 2D passivation can suppress the nonradiative recombination. Moreover, CHMAI can leverage their roles in charge transport/recombination for better performance than phenylethylammonium iodide (Cl/I = 0.114, PCE = 23.32%), due to the stronger binding energy of Cl- . This work provides the insight that the chloride fixation can improve the photovoltaic performance.

Synergistic Effects of Interfacial Energy Level Regulation and Stress Relaxation via a Buried Interface for Highly Efficient Perovskite Solar Cells.

An electron-transport layer with appropriate energy alignment and enhanced charge transfer is critical for perovskite solar cells (PSCs). In addition, interface stress and lattice distortion are inevitable during the crystallization process of perovskite. Herein, IT-4F is introduced into PSCs at the buried SnO2 and perovskite interface, which assists in releasing the residual stress in the perovskite layer. Meanwhile, the work function of SnO2/IT-4F is lower than that of SnO2, which facilitates charge transfer from perovskite to ETL and consequently leads to a significant improvement in the power conversion efficiency (PCE) to 23.73%. The VOC obtained is as high as 1.17 V, corresponding to a low voltage deficit of 0.38 V for a 1.55 eV bandgap. Consequently, the device based on IT-4F maintains 94% of the initial PCE over 2700 h when stored in N2 and retains 87% of the initial PCE after operation for 1000 h.

4-Terminal Inorganic Perovskite/Organic Tandem Solar Cells Offer 22% Efficiency.

After fast developing of single-junction perovskite solar cells and organic solar cells in the past 10 years, it is becoming harder and harder to improve their power conversion efficiencies. Tandem solar cells are receiving more and more attention because they have much higher theoretical efficiency than single-junction solar cells. Good device performance has been achieved for perovskite/silicon and perovskite/perovskite tandem solar cells, including 2-terminal and 4-terminal structures. However, very few studies have been done about 4-terminal inorganic perovskite/organic tandem solar cells. In this work, semi-transparent inorganic perovskite solar cells and organic solar cells are used to fabricate 4-terminal inorganic perovskite/organic tandem solar cells, achieving a power conversion efficiency of 21.25% for the tandem cells with spin-coated perovskite layer. By using drop-coating instead of spin-coating to make the inorganic perovskite films, 4-terminal tandem cells with an efficiency of 22.34% are made. The efficiency is higher than the reported 2-terminal and 4-terminal inorganic perovskite/organic tandem solar cells. In addition, equivalent 2-terminal tandem solar cells were fabricated by connecting the sub-cells in series. The stability of organic solar cells under continuous illumination is improved by using semi-transparent perovskite solar cells as filter.

Molecular Assembled Electrocatalyst for Highly Selective CO2 Fixation to C2+ Products.

In certain metalloenzymes, multimetal centers with appropriate primary/secondary coordination environments allow carbon-carbon coupling reactions to occur efficiently and with high selectivity. This same function is seldom realized in molecular electrocatalysts. Herein we synthesized rod-shaped nanocatalysts with multiple copper centers through the molecular assembly of a triphenylphosphine copper complex (CuPPh). The assembled molecular CuPPh catalyst demonstrated excellent electrochemical CO2 fixation performance in aqueous solution, yielding high-value C2+ hydrocarbons (ethene) and oxygenates (ethanol) as the main products. Using density functional theory (DFT) calculations, in situ X-ray absorption spectroscopy (XAS) and quasi-in situ X-ray photoelectron spectroscopy (XPS), and reaction intermediate capture, we established that the excellent catalytic performance originated from the large number of double copper centers in the rod-shaped assemblies. Cu-Cu distances in the absence of CO2 were as long as 7.9 Å, decreasing substantially after binding CO2 molecules indicating dynamic and cooperative function. The double copper centers were shown to promote carbon-carbon coupling via a CO2 transfer-coupling mechanism involving an oxalate (OOC-COO) intermediate, allowing the efficient production of C2+ products. The assembled CuPPh nanorods showed high activity, excellent stability, and a high Faradaic efficiency (FE) to C2+ products (65.4%), with performance comparable to state-of-the-art copper oxide-based catalysts. To our knowledge, our findings demonstrate that harnessing metalloenzyme-like properties in molecularly assembled catalysts can greatly improve the selectivity of CO2RR, promoting the rational design of improved CO2 reduction catalysts.

In Situ Engineering of the Cu+/Cu0 Interface to Boost C2+ Selectivity in CO2 Electroreduction.

The Cu+/Cu0 interface in the Cu-based electrocatalyst is essential to promote the electrochemical reduction of carbon dioxide (ERCO2) to produce multi-carbon hydrocarbons and alcohols with high selectivity. However, due to the high activity of the Cu+/Cu0 interface, it is easy to be oxidized in the air. How to control and prepare a Cu-based electrocatalyst with an abundant and stable Cu+/Cu0 interface in situ is a huge challenge. Here, combined with density functional theory (DFT) calculations and experimental studies, we found that the trace halide ions adsorbed on Cu2O can slow the reduction kinetics of Cu+ → Cu0, which allowed us to in-situ well control the synthesis of the CuO-derived electrocatalyst with rich Cu+/Cu0 interfaces. Our Cu catalyst with a rich Cu+/Cu0 interface exhibits excellent ERCO2 performance. Under the operation potential of -0.98 V versus RHE, the Faraday efficiency of C2H4 and C2+ products are 55.8 and 75.7%, respectively, which is about 16% higher than that of CuO-derived electrocatalysts that do not use halide ions. The high FEC2+ comes from the improvement of the coupling efficiency of reaction intermediates such as CO-CO, which is proved by DFT calculations, and the suppression of hydrogen evolution reaction. Therefore, we provide an in-situ engineering strategy, which is simple and effective for the design and preparation of high-performance ERCO2 catalysts.

Si/SnSe-Nanorod Heterojunction with Ultrafast Infrared Detection Enabled by Manipulating Photo-Induced Thermoelectric Behavior.

Photothermal detectors have attracted tremendous research interest in uncooled infrared imaging technology but with a relatively slow response. Here, Si/SnSe-nanorod (Si/SnSe-NR) heterojunctions are fabricated as a photothermal detector to realize high-performance infrared response beyond the bandgap limitation. Vertically standing SnSe-NR arrays are deposited on Si by a sputtering method. Through manipulating the photoinduced thermoelectric (PTE) behavior along the c-axis, the Si/SnSe-NRs heterojunction exhibits a unique four-stage photoresponse with a high photoresponsivity of 106.3 V W-1 and high optical detectivity of 1.9 × 1010 cm Hz1/2 W-1 under 1342 nm illumination. Importantly, an ultrafast infrared photothermal response is achieved with the rise/fall time of 11.3/258.7 µs. Moreover, the coupling effect between the PTE behavior and external thermal excitation enables an improved response by 288.4%. The work not only offers a new strategy to develop high-speed photothermal detectors but also performs a deep understanding of the PTE behavior in a heterojunction system.