Enhanced breakage of the aggregates of nanoscale zero-valent iron via ball milling.

Aggregates of nanoscale zero-valent iron (nZVI) are commonly encountered for nZVI in aqueous solution, particularly during large-scale nZVI applications where nZVI is often in a highly concentrated slurry, and such aggregates lower nZVI mobility during its in-situ remediation applications. Herein, we report that the ball milling is an effective tool to break the nZVI aggregates and thereby improve the nZVI mobility. Results show that the milling (in just five minutes) can break the aggregates of a few tens of microns to less than one micron, which is one-tenth of the size that is acquired via the breakage using the mechanical mixing and ultrasonication. The milling breakage can also improve the efficacy of the chemical conditioning method that is commonly used for the nanoparticle stabilization and dispersion. The milling breakage is further optimized via a study of the milling operational factors including milling time, bead velocity, bead diameter, and chamber porosity, and an empirical equation is proposed combining the bead collision number during the milling. Mechanistic study shows that the high efficacy of the milling to break the aggregates can be explained by the small eddy created by the high shear rate produced by the close contact of the milling beads and may also relate to the direct mechanical pulverization effect. This study provides a high efficacy physical method to break the nanoparticle aggregates. The method can be used to improve the nZVI mobility performance by milling the nZVI slurry before its injection for in-situ remediation, and the milling may also replace the mechanical mixing during the nZVI stabilization via surface modification.

Exploring effect of uniform dry ball-milling duration on pasting and rheological properties of pink potato and maize starch mixtures.

This study examined the potential effect of ball milling on maize starch (MS), pink potato starch (PPS), and their blends in various ratios (90:10, 80:20, and 70:30) on the pasting and rheological properties. Ball-milling led to changes in the particle size, ranging from 652.9 to 6488 nm, and a decrease in relative crystallinity (RC), as confirmed by XRD. Ball-milling increased amylose concentration in blend with the ratio of 90:10 up to 32.53 %, indicating structural alterations and molecular interactions. FESEM analysis confirms significant changes in the surface and particle sizes and starch gels with honeycomb structures. FTIR and Raman spectroscopy revealed a decrease in the intensity of the 1044 cm-1 and 480 cm-1 bands, respectively, signifying structural changes. Pasting parameters like peak viscosity and gelatinization behavior varied with PPS incorporation. The 80:20 blend had the highest viscosity, demonstrating PPS's capacity for high-viscosity starch paste. Rheological measurements of starch blends exhibited shear-thinning behavior, whereas the viscoelastic properties of the blends are influenced by particle size and the ratio of pink potato starch. Ball-milling treatment affects the granules and causes molecular-level interactions between the particles. This results in unique rheological properties of the starch blends, making them suitable for various applications.

Ball Milling Innovations Advance Mg-Based Hydrogen Storage Materials Towards Practical Applications.

Mg-based materials have been widely studied as potential hydrogen storage media due to their high theoretical hydrogen capacity, low cost, and abundant reserves. However, the sluggish hydrogen absorption/desorption kinetics and high thermodynamic stability of Mg-based hydrides have hindered their practical application. Ball milling has emerged as a versatile and effective technique to synthesize and modify nanostructured Mg-based hydrides with enhanced hydrogen storage properties. This review provides a comprehensive summary of the state-of-the-art progress in the ball milling of Mg-based hydrogen storage materials. The synthesis mechanisms, microstructural evolution, and hydrogen storage properties of nanocrystalline and amorphous Mg-based hydrides prepared via ball milling are systematically reviewed. The effects of various catalytic additives, including transition metals, metal oxides, carbon materials, and metal halides, on the kinetics and thermodynamics of Mg-based hydrides are discussed in detail. Furthermore, the strategies for synthesizing nanocomposite Mg-based hydrides via ball milling with other hydrides, MOFs, and carbon scaffolds are highlighted, with an emphasis on the importance of nanoconfinement and interfacial effects. Finally, the challenges and future perspectives of ball-milled Mg-based hydrides for practical on-board hydrogen storage applications are outlined. This review aims to provide valuable insights and guidance for the development of advanced Mg-based hydrogen storage materials with superior performance.

Recent Advances in the Preparation Methods of Magnesium-Based Hydrogen Storage Materials.

Magnesium-based hydrogen storage materials have garnered significant attention due to their high hydrogen storage capacity, abundance, and low cost. However, the slow kinetics and high desorption temperature of magnesium hydride hinder its practical application. Various preparation methods have been developed to improve the hydrogen storage properties of magnesium-based materials. This review comprehensively summarizes the recent advances in the preparation methods of magnesium-based hydrogen storage materials, including mechanical ball milling, methanol-wrapped chemical vapor deposition, plasma-assisted ball milling, organic ligand-assisted synthesis, and other emerging methods. The principles, processes, key parameters, and modification strategies of each method are discussed in detail, along with representative research cases. Furthermore, the advantages and disadvantages of different preparation methods are compared and evaluated, and their influence on hydrogen storage properties is analyzed. The practical application potential of these methods is also assessed, considering factors such as hydrogen storage performance, scalability, and cost-effectiveness. Finally, the existing challenges and future research directions in this field are outlined, emphasizing the need for further development of high-performance and cost-effective magnesium-based hydrogen storage materials for clean energy applications. This review provides valuable insights and references for researchers working on the development of advanced magnesium-based hydrogen storage technologies.

Starch nanoparticles with predictable size prepared by alternate treatments of ball milling and ultrasonication.

In this study, starch nanoparticles (SNPs) were prepared by alternate treatments of liquid nitrogen ball milling and ultrasonication. The impact, shear and friction forces produced by ball milling, and acoustic cavitation and shear effects generated by ultrasonication disrupted starch granules to prepare SNPs. The SNPs possessed narrow particle size distribution (46.91-210.52 nm) and low polydispersity index (0.28-0.45). Additionally, the SNPs exhibited the irregular fragments with good uniformity. The relative crystallinity decreased from 34.91 % (waxy corn starch, WCS) to 0-25.91 % (SNPs), and the absorbance ratios of R1047/1022 decreased from 0.81 (WCS) to 0.60-0.76 (SNPs). The SNPs had lower thermal stability than that of WCS, characterized by a decrease in Td (temperature at maximum weight loss) from 309.39 °C (WCS) to 300.39-305.75 °C (SNPs). Furthermore, the SNPs exhibited excellent swelling power (3.48-28.02 %) and solubility (0.34-0.97 g/g). Notably, oil absorption capacity of the SNPs (9.77-15.67 g/g) was rather greater than that of WCS (1.33 g/g). Furthermore, the SNPs possessed the lower storage modulus (G'), loss modulus (G″) and viscosity than that of WCS. The SNPs with predictable size and high dispersion capability prepared in this study lay a foundation for expanding the application of SNPs.

Bosentan monohydrate and sildenafil base as two companions in enabling formulations.

HYPOTHESIS: Sildenafil base and bosentan monohydrate are co-administered in a chronic therapy of pulmonary arterial hypertension (PAH). Both drugs are poorly soluble in water, and their bioavailability is limited to ca. 50 %. Since bosentan is a weak acid, whereas sildenafil is a weak base, we assumed that their co-amorphization could: (i) improve their solubility in the gastrointestinal fluids, (ii) enable to reach supersaturation and (iii) ensure stabilization of supersaturated solutions. If successful, this could accelerate the development of new fixed-dose combination drugs. EXPERIMENTS: The co-amorphous formulations were prepared using high energy ball milling. Their solid state properties were assessed using XRD, DSC, FT-MIR, and dielectric spectroscopy. Particle size distribution and surface wetting were also analyzed. Polarizing optical microscopy and scanning electron microscopy were applied to assess the microstructure of these powders. A new HPLC-DAD method was developed for a simultaneous quantification of both drugs. FINDINGS: It was shown that binary formulations in which bosentan was molecularly dispersed in sildenafil base (Tg = 64-78 °C) could be manufactured in the high energy ball milling process. When the sildenafil load was below 50 wt. %, the formulations showed the greatest thermal stability and formed long-lasting bosentan supersaturation in PBS.

Mechanochemical Synthesis of Silylcyclopentenes via Ball Milling.

The development of innovative methods for synthesizing silylcyclopentene compounds is particularly important for enriching and improving the synthetical toolbox of organosilicon compounds. Herein, a facile approach has been developed for the synthesis of silylcyclopentenes promoted by mechanochemically generated organolithium species as silicon nucleophiles under ball milling conditions, avoiding the requirement of large amounts of bulk solvent. This operationally simple method demonstrates good functional group compatibility, which provides a great opportunity for further exploration of the synthetic applications of silylcyclopentenes. Density functional theory calculations indicated that the transient lithiosilole intermediates undergo a stepwise nucleophilic addition process, which governs this mechanic-force-promoted [4+1] cycloaddition reaction.

Novel insights into the mechanism of dynamic changes in microstructure and physicochemical properties of corn straw pretreated by ball milling and feasibility analysis of anaerobic digestion.

In this study, the effects of Ball milling (BM) pretreatment (0-240 min) on the microstructure, physicochemical properties and subsequent methanogenesis performance of corn straw (CS) were explored, and the feasibility analysis was carried out. The results showed that BM pretreatment destroyed the dense structure of the CS, and the particle size was significantly reduced (D50: 13.85 µm), transforming it into a cell-scale granular form. The number of mesopores increased, the pore volume (PV) (0.032 cm3/g) and specific surface area (SSA) (4.738 m2/g) considerably increased, and the water-absorbent property was improved. The crystalline order of cellulose was disrupted and the crystallinity (CrI) (8.61 %) and crystal size (CrS) (3.37) were remarkably reduced. The cross-links between lignocelluloses were broken, and the relative content and functional groups did not alter obviously. The bulk density (BD), repose angle (RA) and slip angle (SA) dramatically increased. As a result, CS was more readily accessible, attached and utilized by microorganisms and enzymes, causing the hydrolysis and acidification of AD to be greatly facilitated. Compared with the untreated group, the cumulative methane production (CMP) increased by 35.83 %-101.97 %, and the lag phase time (λ) was shortened by 33.04 %-71.17 %. The results of redundancy analysis, Pearson analysis and Mantel test showed that BM pretreatment affects the process of AD by changing the physicochemical factors of CS. The normalization analysis showed that particle size (D90) and BD can be used as direct indicators to evaluate the performance of AD and predict the threshold of biodegradation of CS. Energy analysis and energy conversion assessment showed that BM is a green and efficient AD pretreatment strategy. This result provides a theoretical basis for the industrial application of BM pretreatment towards more energy-efficient and sustainable development.

Effect of Ball-Milling Treatment Combined with Glycosylation on the Structure and Functional Properties of Litopenaeus vannamei Protein.

Litopenaeus vannamei protein (LVP) is a high-quality protein. However, its functional properties do not fully meet the needs of food processing. In this study, LVP-xylose conjugates were prepared by conventional wet heat method (GLVP) and ball-milling-assisted wet heat method (GBLVP), respectively. The changes in structure and functional properties of the glycosylated LVP were explored. The findings revealed that ball-milling pretreatment increased the grafting degree to 35.21%. GBLVP had a sparser surface structure and lower particle size than GLVP. FTIR spectra showed that xylose was grafted onto LVP successfully and GBLVP had the lowest α-helix content. Compared with GLVP, GBLVP had a decrease in intrinsic fluorescence intensity and surface hydrophobicity, and an increase in UV absorption intensity. Moreover, GBLVP had higher foaming capacity, solubility and water-holding capacity, and lower allergenicity than GLVP. However, ball-milling pretreatment had a negative impact on the vitro digestibility and oil-holding capacity of GBLVP. In conclusion, ball-milling-assisted treatment of glycosylation could effectively improve the functional properties of LVP, benefiting the broader application of LVP in the food industry.

Impact of water combined wet ball milling extraction and functional evaluation of dietary fiber from papaya (Carica papaya L).

This study evaluates the structural, physicochemical, functional and rheological properties of papaya dietary fibers (DFs) extracted by alkaline, water and combination of water/wet ball milling. The particle size of DF subjected to water/wet ball milling (WB-DF) was considerably reduced compared to DF extracted by water (W-DF) or alkaline (AL-DF) methods. WB-DF in comparison AL-DF increased the water holding capacity (WHC) by 4.1 folds, oil holding capacity (OHC) by 1.7 folds and water swelling capacity (WSC) by 2.6 folds. WB-DF also improved the cholesterol adsorption capacity (CAC), glucose adsorption (GAC), nitrite-ion adsorption capacity (NIAC) and antioxidant activity. The FT-IR spectra displayed changes in peak intensities observed in the three modified DFs. In addition, WB-DF showed highest viscosity among all smaples. The distributions of monosaccharides in the DFs were affected by the different extractions. Consequently, DFs extracted through the water/wet ball milling exhibit significant potential for applications in the functional food industry.

Calcium Carbide (CaC2) as a C2-Synthon by Mechanochemistry.

Mechanochemical reactions by ball milling have opened new avenues in chemical synthesis. Particularly, mechanochemistry has facilitated the reaction of insoluble materials to simplify stablished synthetic protocols and develop new ones. One notable application involves the use of calcium carbide (CaC2) as a C2-synthon through mechanochemistry, which has offered a more practical alternative to incorporate C2-units compared to the conventional use of highly flammable gaseous acetylene. For example, by ball milling the acetylenic anions [C2]2- found in CaC2 have been harnessed for the synthesis of diverse functional carbon materials as well as discrete organic molecules. This Concept aims to contribute to the conceptualization of this innovative approach, while highlighting both its advantages and the challenges inherent in the use of CaC2.

Predictive computational models for assessing the impact of co-milling on drug dissolution.

Co-milling is an effective technique for improving dissolution rate limited absorption characteristics of poorly water-soluble drugs. However, there is a scarcity of models available to forecast the magnitude of dissolution rate improvement caused by co-milling. Therefore, this study endeavoured to quantitatively predict the increase in dissolution by co-milling based on drug properties. Using a biorelevant dissolution setup, a series of 29 structurally diverse and crystalline drugs were screened in co-milled and physically blended mixtures with Polyvinylpyrrolidone K25. Co-Milling Dissolution Ratios after 15 min (COMDR15 min) and 60 min (COMDR60 min) drug release were predicted by variable selection in the framework of a partial least squares (PLS) regression. The model forecasts the COMDR15 min (R2 = 0.82 and Q2 = 0.77) and COMDR60 min (R2 = 0.87 and Q2 = 0.84) with small differences in root mean square errors of training and test sets by selecting four drug properties. Based on three of these selected variables, applicable multiple linear regression equations were developed with a high predictive power of R2 = 0.83 (COMDR15 min) and R2 = 0.84 (COMDR60 min). The most influential predictor variable was the median drug particle size before milling, followed by the calculated drug logD6.5 value, the calculated molecular descriptor Kappa 3 and the apparent solubility of drugs after 24 h dissolution. The study demonstrates the feasibility of forecasting the dissolution rate improvements of poorly water-solube drugs through co-milling. These models can be applied as computational tools to guide formulation in early stage development.

Enhanced microstructure and mechanical properties of ZrN-reinforced AlSi10Mg aluminum matrix composite.

Aluminum matrix composites (AMCs), incorporating Zirconium Nitride (ZrN) as reinforcing additives, demonstrate immense promise for applications in aerospace, automotive, and power generation due to their unique combination of low density, superior mechanical properties, and excellent thermal/electrical conductivity. This study explores the influence of ZrN reinforcement on the microstructure and mechanical properties of AlSi10Mg metal-matrix composites. Utilizing high-energy ball milling (HEBM) and spark-plasma sintering (SPS), ZrN/AlSi10Mg composites were synthesized, achieving nearly full density with uniform ZrN distribution, while phase and chemical transformations were not observed in the bulk composites. The addition of ZrN resulted in a notable increase in hardness of 237% (182 ± 8 HV2), elastic modulus of 56% (114 ± 3 GPa), compressive and tensile strength of 183% (565 ± 15 GPa), and 125% (387 ± 9 GPa), respectively, for composites containing 30% ZrN, compared to the non-reinforced alloy. Experimentally determined coefficients of thermal expansion (CTEs) for composites with 10%, 20%, and 30% ZrN content were 19.8 × 10-6 °C-1, 19.1 × 10-6 °C-1, and 18 × 10-6 °C-1, respectively, which well relates to Schapery's model. These findings contribute to understanding the synthesis, mechanical behavior, and thermal properties of ZrN/AlSi10Mg composites, demonstrating their potential for diverse engineering applications.

Ball-milled biochar-modified zero-valent aluminum activates peroxodisulfate for phenol degradation: Enhancement of catalysis by membrane-breaking effect.

Zero-valent aluminum (ZVAl) is a potential activator for peroxodisulfate (PDS), yet the dense oxide film on its surface hampers electron transfer for the O-O bond cleavage of PDS. We synthesized zero-valent aluminum-biochar (BM-ZVAl@BC) composites through ball milling, which effectively disrupted the native oxide layer on BM-ZVAl@BC. Within the BM-ZVAl@BC/PDS system, biochar (BC) not only suppressed the rapid oxidation of BM-ZVAl@BC but also enhanced the dispersion and electron transfer rate of ZVAl, thereby improving the overall catalytic efficiency. Consequently, the phenol removal efficacy in the BM-ZVAl@BC/PDS system was notably improved. Optimal catalytic performance of the prepared BM-ZVAl@BC was achieved at a charcoal-to­aluminum mass ratio of 2:1, resulting in 95.7 % phenol removal after 180 min. Quenching experiments and electron paramagnetic resonance (EPR) analysis revealed that both free radicals (SO4•-, •OH, and O2•-) and non-radical species (1O2) contributed to phenol degradation, with SO4•- and •OH playing predominant roles. In summary, the BM-ZVAl@BC/PDS system represented an effective and promising technology for the remediation of phenolic water pollutants.

Characterization of bamboo shoots dietary fiber modified by ball milling and its role in altering the physicochemical properties of shrimp surimi.

A simple but robust strategy of ball milling (20 Hz, 30 Hz for 30 s, 60 s, 120 s, 180 s) was utilized to modify bamboo shoots fiber (BSDF) in shrimp surimi. The water holding capacity, swelling capacity, and oil binding capacity of 30 Hz-60 s milled BSDF exhibited the highest values of 5.61 g/g, 3.13 mL/g, and 6.93 g/g, significantly higher (P < 0.05) than untreated one (3.65 g/g, 2.03 mL/g, 4.57 g/g). Ball-milled BSDF exhibited a small-sized structure with the relative crystallinity decreased from 40.44 % (control) to 11.12 % (30 Hz-180 s). The myosin thermal stability, gelation properties of surimi were significantly enhanced by incorporating 20 Hz-120 s and 30 Hz-60 s BSDF via promoting protein unfolding, covalent hydrophobic interactions, and hydrogen bonding. A matrix-reinforcing and water entrapping effect was observed, exhibiting reinforced networks with down-sized water tunnels. However, BSDF modified at 180 s contributed to over-aggregated networks with fractures and enlarged gaps. Appropriate ball-milled BSDF (20 Hz-120 s, and 30 Hz-60 s) resulted in a significant decrease in α-helix (P < 0.05), accompanied by an increase of ß-sheets and ß-turn. This work could bring some insights into the applications of modified BSDF and its roles in the gelation of surimi-based food.

Enhancing the Electrochemical Performances of Disordered Li1.23Ni0.3Nb0.3Fe0.16O0.85F0.15 Cathode Material for Lithium-Ion Batteries by LiNbOx Coating.

For the next generation of lithium-ion batteries (LIBs), it is primary to seek high capacity and long-lifetime electrode materials. Li-excess disordered rock-salt structure (DRS) cathodes have gained much attention due to their high specific capacity. However, Li-excess can lead to a decrease in the structural stability of an electrode material. A new Li-rich DRS oxyfluorides, Li1.23Ni0.3Nb0.3Fe0.16O0.85F0.15 (F0.15) with a series amounts of LiNbOx (LN) coating (0, 5, 10, and 15 wt % denoted as F0.15-LN0, F0.15-LN5, F0.15-LN10, and F0.15-LN15, respectively), are successfully synthesized and evaluated as cathode materials in LIBs. Among them, F0.15-LN10 exhibits the highest initial discharge specific capacity of 296.1 mAh g-1 (at a current density of 20 mA g-1) with the capacity retention rate of 14% higher than that of the uncoated F0.15 after 80 cycles. Even at 300 mA g-1, F0.15-LN10 still delivers the highest discharge specific capacity of 130 mAh g-1. After 20 cycles, the charge-transfer impedance of F0.15-LN10 remained the smallest. The characterizations indicate that LN coating reduces the surface polarization of the cathode materials, slows the interfacial side reactions between the electrolyte and the electrode, and speeds up the Li+ diffusion. These results demonstrate that LN coating is an effective strategy to improve the electrochemical performance.

Extractability and chromatographic separation of proteins from potato (Solanum tuberosum L.) trimmings.

By-products from the potato processing industry, like potato trimmings, are sustainable sources of proteins. Here, a size-exclusion high performance liquid chromatography (SE-HPLC) method was applied to simultaneously determine the extractability and aggregation state of proteins from three batches of potato trimmings of different cultivars. Obtained SE-HPLC profiles allowed distinguishing between the patatin and protease inhibitor fractions of potato proteins. Moreover, only 75% of the crude proteins could be extracted in phosphate buffer containing sodium dodecyl sulfate and a reducing agent, indicating the presence of physical extraction barriers. Ball milling for 5 min significantly increased protein extractability, but prolonged treatment resulted in aggregation of native patatin and a reduced protein extractability. Microwave-dried trimmings had a lower protein extractability than freeze-dried trimmings. In future research, the SE-HPLC method can be used to examine changes in potato protein (fractions) as a result of processing.

Mechanical-Force-Induced Non-spontaneous Dehalogenative Deuteration of Aromatic Iodides Enabled by Using Piezoelectric Materials as a Redox Catalyst.

The development of green and efficient deuteration methods is of great significance for various fields such as organic synthesis, analytical chemistry, and medicinal chemistry. Herein, we have developed a dehalogenative deuteration strategy using piezoelectric materials as catalysts in a solid-phase system under ball-milling conditions. This non-spontaneous reaction is induced by mechanical force. D2O can serve as both a deuterium source and an electron donor in the transformation, eliminating the need for additional stoichiometric exogenous reductants. A series of (hetero)aryl iodides can be transformed into deuterated products with high deuterium incorporation. This method not only effectively overcomes existing synthetic challenges but can also be used for deuterium labelling of drug molecules and derivatives. Bioactivity experiments with deuterated drug molecule suggest that the D-ipriflavone enhances the inhibitory effects on osteoclast differentiation of BMDMs in vitro.

Aerobic Oxidative Desulfurization by Supported Polyoxometalate Ionic Liquid Hybrid Materials via Facile Ball Milling.

With the increasingly strict limitations on emission standards of vehicles, deep desulfurization in fuel is indispensable for social development worldwide. In this study, a series of hybrid materials based on SiO2-supported polyoxometalate ionic liquid were successfully prepared via a facile ball milling method and employed as catalysts in the aerobic oxidative desulfurization process. The composition and structure of prepared samples were studied by various techniques, including FT-IR, UV-vis DRS, wide-angle XRD, BET, XPS, and SEM images. The experimental results indicated that the synthesized polyoxometalate ionic liquids were successfully loaded on SiO2 with a highly uniform dispersion. The prepared catalyst (C16PMoV/10SiO2) exhibited good desulfurization activity on different sulfur compounds. Moreover, the oxidation product and active species in the ODS process were respectively investigated via GC-MS and ESR analysis, indicating that the catalyst can activate oxygen to superoxide radicals during the reaction to convert DBT to its corresponding sulfone in the fuel.

Promoting Effect of Ball Milling on the Functionalization and Catalytic Performance of Carbon Nanotubes in Glycerol Etherification.

A facile and eco-friendly approach using in situ-generated 4-benzenediazonium sulfonate (BDS) was applied to prepare highly functionalized carbon nanotubes (CNTs). The effectiveness of this functionalization was additionally enhanced by a green and short-time ball milling process applied beforehand. The obtained BDS-modified CNTs presented significant activity in glycerol etherification, producing tert-butyl glycerol ethers, which are considered promising fuel additives. Excellent results of ~56% glycerol conversion and ~10% yield of higher-substituted tert-butyl glycerol ethers were obtained within just 1 h of reaction at 120 °C using a low catalyst loading of only 2.5 wt.%. Furthermore, the sulfonated CNTs were reusable over several reaction cycles, with only a minor decrease in activity. Additionally, the sample activity could be restored by a simple regeneration approach. Finally, a clear correlation was found between the content of -SO3H groups on the surface of CNTs and the catalytic performances of these materials in glycerol etherification. Improved interaction between functionalized ball-milled CNTs and the reactants was also suggested to positively affect the activity of these catalysts in the tested process.