Research on the Mechanical and Thermal Properties of Carbon-Fiber-Reinforced Rubber Based on a Finite Element Simulation.

The comprehensive performance of rubber products could be significantly improved by the addition of functional fillers. To improve research efficiency and decrease the experimental cost, the mechanical and thermal properties of carbon-fiber-reinforced rubber were investigated using finite element simulations and theoretical modeling. The simplified micromechanical model was constructed through the repeatable unit cell with periodic boundary conditions, and the corresponding theoretical models were built based on the rule of mixture (ROM), which can be treated as the mutual verification. The simulation results suggest that, in addition to the fiber volume fraction Vfc increasing from 10% to 70%, the longitudinal Young's modulus, transversal Young's modulus, in-plane shear modulus, longitudinal thermal expansion coefficient, and transversal thermal expansion coefficient changed from 2.31 × 1010 Pa to 16.09 × 1010 Pa, from 0.54 × 107 Pa to 2.59 × 107 Pa, from 1.66 × 106 Pa to 10.11 × 106 Pa, from -4.98 × 10-7 K-1 to -5.89 × 10-7 K-1, and from 5.72 × 10-4 K-1 to 1.66 × 10-4 K-1, respectively. The mechanism by which Vfc influences the properties of carbon-fiber-reinforced rubber was revealed through the distribution of Von Mises stress. This research will contribute to improving the performance of carbon-fiber-reinforced rubber and promote its application.

Design and Computational Validation of γ-Ray Shielding Effectiveness in Heavy Metal/Rare Earth Oxide-Natural Rubber Composites.

This study involved the preparation of natural rubber-based composites incorporating varying proportions of heavy metals and rare earth oxides (Sm2O3, Ta2O5, and Bi2O3). The investigation analyzed several parameters of the samples, including mass attenuation coefficients (general, photoelectric absorption, and scattering), linear attenuation coefficients (µ), half-value layers (HVLs), tenth-value layers (TVLs), mean free paths (MFPs), and radiation protection efficiencies (RPEs), utilizing the Monte Carlo simulation software Geant4 and the WinXCom database across a gamma-ray energy spectrum of 40-150 keV. The study also compared the computational discrepancies among these measurements. Compared to rubber composites doped with single-component fillers, multi-component mixed shielding materials significantly mitigate the shielding deficiencies observed with single-component materials, thereby broadening the γ-ray energy spectrum for which the composites provide effective shielding. Subsequently, the simulation outcomes were juxtaposed with experimental data derived from a 133Ba (80 keV) γ-source. The findings reveal that the simulated results align closely with the experimental observations. When compared to the WinXCom database, the Geant4 software demonstrates superior accuracy in deriving radiation shielding parameters and notably enhances experimental efficiency.

Correlating the Segmental Relaxation Time of Polystyrene.

A previous related paper dealing with the density relaxation of polystyrene (PS) has shown that the equilibrium relaxation time (τeq) has a purely exponential temperature dependence (ETD) below ≈100 °C. Such an ETD is now also confirmed based upon available dielectric spectra data for PS. By combining the ETD behavior of τeq (or aT) at low temperatures with a VFTH behavior at higher temperatures (based mainly on available recoverable shear compliance data), a composite correlation for τeq (or aT) is developed, which is continuous with continuous slope at a crossover temperature that is found to be 99.22 °C, where τeq = 92.15 s. This composite representation is shown to describe (without any adjustable parameters) available independent data for the segmental relaxation time over a finite range both above and below Tcrossover (i.e., the glass transition temperature).

Study on Basic Pavement Performance of High-Elasticity Asphalt Concrete.

In order to improve the basic pavement performance of high-elastic asphalt concrete filled in the expansion longitudinal joints of seamless bridges, rubber particles and polyester fibers were added to optimize the mix proportion of elastic asphalt concrete, and the optimal asphalt-aggregate ratio was determined. The influence of rubber particles and polyester fibers on the basic pavement performance of high-elastic asphalt concrete was studied. The results show that when the dosage of polyester fiber is not more than 0.6%, the optimal asphalt-aggregate ratio is 1:5, and when it exceeds 0.6%, the optimal asphalt-aggregate ratio is 1:4. The incorporation of rubber particles reduces the compressive strength of high-elastic asphalt concrete but enhances its high-temperature stability, fracture performance, and deformation recovery ability. The incorporation of polyester fibers improves its compressive strength, high-temperature stability, fracture performance, and deformation recovery ability. In addition, the incorporation of rubber granules and polyester fibers promotes the use of green building materials and provides strong support for sustainable building practices.

A Cost-Effective Approach to Creating Large Silicone Rubber Molds Using Advanced Rigid Polyurethane Foam.

In practical applications, polyurethane (PU) foam must be rigid to meet the demands of various industries and provide comfort and protection in everyday life. PU foam components are extensively used in structural foam, thermal insulation, decorative panels, packaging, imitation wood, and floral foam, as well as in models and prototypes. Conventional technology for producing PU foam parts often leads to defects such as deformation, short shots, entrapped air, warpage, flash, micro-bubbles, weld lines, and voids. Therefore, the development of rigid PU foam parts has become a crucial research focus in the industry. This study proposes an innovative manufacturing process for producing rigid PU foam parts using silicone rubber molds (SRMs). The deformation of the silicone rubber mold can be predicted based on its wall thickness, following a trend equation with a correlation coefficient of 0.9951. The volume of the PU foam part can also be predicted by the weight of the PU foaming agent, as indicated by a trend equation with a correlation coefficient of 0.9824. The optimal weight ratio of the foaming agent to water, yielding the highest surface hardness, was found to be 5:1. The surface hardness of the PU foam part can also be predicted based on the weight of the water used, according to a proposed prediction equation with a correlation coefficient of 0.7517. The average surface hardness of the fabricated PU foam part has a Shore O hardness value of approximately 75. Foam parts made with 1.5 g of water added to 15 g of a foaming agent have the fewest internal pores, resulting in the densest interior. PU foam parts exhibit excellent mechanical properties when 3 g of water is added to the PU foaming agent, as evidenced by their surface hardness and compressive strength. Using rigid PU foam parts as a backing material in the proposed method can reduce rapid tool production costs by about 62%. Finally, an innovative manufacturing process for creating large SRMs using rigid PU foam parts as backing material is demonstrated.

Composites Based on Eucalyptus Nitens Leaves and Natural Rubber as a Valuable Alternative for the Development of Elastomeric Materials with Low Microbiological Impact.

The forest industry produces several low-value by-products, such as bark, sawdust, limbs, and leaves, that are not ultimately disposed of and remain in the forests and sawmill facilities. Among these by-products are leaves, which contain not only cellulose fibers and lignin but also essential oils such as terpenes. These are biosynthesized in a similar way as cis-1,4-polyisoprene. In this context, this work evaluates the use of screened and unscreened dried Eucalyptus nitens leaves in natural rubber. Among the most relevant results of this work is a significant increase in mechanical properties, such as tensile strength and elongation at break, reaching values of 9.45 MPa and 649% of tensile strength and elongation at break, respectively, for a sample of natural rubber containing sieved dried leaves of Eucalyptus nitens. In addition, it is observed that the content of this vegetable filler allows for inhibiting the antibacterial effect of vulcanized rubber against several bacteria, such as Bacillus subtilis, Staphylococcus aureus, Escherichia coli K 12, Escherichia coli FT 17 and Pseudomonas fluorescens. These results are promising because they not only add value to a by-product of the forestry industry, improving the mechanical properties of natural rubber from a sustainable approach but also increase the affinity of rubber with bacterial microorganisms that may play a role in certain ecosystems.

Thermoplastic Vulcanizates with an Integration of High Wear-Resistant and Anti-Slip Properties Based on Styrene Ethylene Propylene Styrene Block Copolymer/Styrene Ethylene Butylene Styrene Block Copolymer/Solution-Polymerization Styrene-Butadiene Rubber.

Distinguished from traditional vulcanized rubber, which is not reusable, thermoplastic elastomer (TPV) is a material that possesses both the excellent resilience of traditional vulcanized rubber and the recyclability of thermoplastic, and TPVs have been widely studied in both academia and industry because of their outstanding green properties. In this study, new thermoplastic elastomers based on solution polymerized styrene butadiene rubber (SSBR) and thermoplastic elastomers (SEPSs/SEBSs) were prepared by the first dynamic vulcanization process. The high slip resistance and abrasion resistance of SSBR are utilized to improve the poor slip resistance of SEPSs/SEBSs, which provides a direction for the recycling of shoe sole materials. In this paper, the effects of different ratios of the rubber/plastic phase (R/P) on the mechanical properties, rheological properties, micro-morphology, wear resistance, and anti-slip properties of SSBR/TPE TPVs are investigated. The results show that the SSBR/TPE TPVs have good mechanical properties. The tensile strength, tear strength, hardness, and resilience of the TPVs decrease slightly with an increasing R/P ratio. Still, TPVs have a tensile strength of 18.1 MPa when the ratio of R/P is 40/100, and this reaches the performance of the vulcanized rubber sole materials commonly used in the market. In addition, combined with microscopic morphology analysis (SEM), it was found that, with the increase in the R/P ratio, the size of the rubber particles gradually increased, forming a stronger crosslinking network, but the rheological properties of TPVs gradually decreased; crosslinking network enhancement led to the increase in the size of the rubber particles, and the increase in the size of rubber particles made the material in the abrasion of rubber particles fall easily, thus increasing its abrasion volume. Through dynamic mechanical analysis and anti-slip tests, when the R/P ratio was 40/100, the tan δ of TPVs at 0 °C was 0.35, which represents an ordinary vulcanized rubber sole material in the market. The viscoelasticity of TPVs increased with the increase in the R/P ratio, which improved the anti-slip performance of TPVs. SSBR/TPE TPVs are expected to be used in footwear and automotive fields due to their excellent abrasion resistance and anti-slip performance.

Outcome and predictive factors for perforation in orthodontic rubber band-assisted endoscopic submucosal dissection of fibrotic colorectal lesions.

Endoscopic submucosal dissection (ESD) of fibrotic colorectal lesions is difficult and has a high complication rate. There are only a few reports on the utility of orthodontic rubber band (ORB) traction in reducing the difficulty of this procedure. This study aimed to investigate the risk factors for perforation when applying ORB traction during ESD of fibrotic colorectal lesions. We continuously collected the clinical data of 119 patients with fibrotic colorectal lesions who underwent ESD with ORB and clip traction between January 2019 and January 2024. Possible risk factors for perforation were analyzed. The median ORB-ESD operative time was 40 (IQR 28-62) min, and the en bloc and R0 resection rates were 94.1% and 84.0%, respectively. Perforation occurred in 16 of 119 patients (13.4%). The lesion size, lesion at the right half of the colon or across an intestinal plica, the degree of fibrosis, operation time, and the surgeon's experience were associated with perforation during ORB-ESD (P < 0.05). Multivariate logistic regression analysis showed that lesions in the right colon (OR 9.027; 95% CI 1.807-45.098; P = 0.007) and those across an intestinal plica (OR 7.771; 95% CI 1.298-46.536; P = 0.025) were independent risk factors for perforation during ORB-ESD. ORB-ESD is an effective and feasible approach to treat fibrotic colorectal lesions. Adequate preoperative evaluation is required for lesions in the right colon and across intestinal plicas to mitigate the risk of perforation.

Precipitation contributes to alleviating pollution of rubber-derived chemicals in receiving watersheds: Combining confluent stormwater runoff from different functional areas.

The release of rubber-derived chemicals (RDCs) in road surface runoff has received significant attention. Urban surface runoff is often the confluence of stormwater runoff from specific areas. However, the impact of precipitation on RDCs contamination in confluent stormwater runoff and receiving watersheds remains poorly understood. Herein, we investigated the profiles of RDCs and their transformation products in confluent stormwater runoff and receiving rivers affected by precipitation events. The results showed that 34 RDCs are ubiquitously present in confluent stormwater runoff and surface water, with mean concentrations of 1.03-2749 and 0.28-436 ng/L, respectively. The most dominant target compounds in each category were N-(1,3-dimethylbutyl)-N'-phenyl-p-phenylenediamine (6PPD), 6PPD-quinone, 2-benzothiazolol, and 1,3-diphenylguanidine. Total RDCs concentrations in confluent stormwater runoff decreased spatially from industrial areas to business districts to college towns. A significant decrease in RDCs levels in surface water after rainfall was observed (P < 0.01), indicating that precipitation contributes to alleviating RDCs pollution in receiving watersheds. To our knowledge, this is the first report of N,N'-ditolyl-p-phenylenediamine quinone (DTPD-Q) levels in surface waters in China. The annual mass load of ∑RDCs reached 72,818 kg/y in confluent stormwater runoff, while 38,799 kg/y in surface water. The monitoring of confluent stormwater runoff is an efficient measure for predicting contamination loads from RDCs in rivers. Risk assessment suggested that most RDCs posed at least medium risks to aquatic organisms, especially 6PPD-quinone. The findings help to understand the environmental fate and risks of RDCs in the confluent stormwater runoff and receiving environments after precipitation events.

Revealing the dual impact of VOCs on recycled rubber workers: Health risk and odor perception.

Volatile organic compounds (VOCs) pose potential hazards to human health and contribute significantly to odor pollution. This study examined VOC emissions from a representative recycled rubber industry, evaluating the occupational health risks for frontline workers in various workshops. Variables such as gender and workshop-specific concentration variations were considered using Monte Carlo simulation methods. Employees in the five production workshops and office areas face noncarcinogenic health risks with hazard indices (HIs) greater than 1, with the rubber compounding phase presenting the highest risk. Acetaldehyde is identified as the primary noncarcinogenic health risk substance, with hazard quotient (HQ) values exceeding 1 in all workshops. Carcinogenic health risks vary by area, with the highest risks found in compounding and refining workshops. Formaldehyde poses the greatest risk in rubber grinding workshops and offices, with cumulative weights exceeding unacceptable levels of M80.58 % and W77.56 % in grinding and M94.98 % and W92.24 % in the office. Male workers face 4-7 % greater noncarcinogenic VOC health risks than females and 5-14 % greater carcinogenic risks from individual VOCs, increasing their susceptibility to health risks caused by VOCs. Additionally, our analysis of odor identification and intensity classification revealed that 53 VOCs are capable of causing odor pollution, with several substances reaching odor levels of 2 or higher. The predominant perceived odors, as reflected in the odor wheel, include categories such as "solvent/aromatic" and "sweet/fruit," with aldehydes being the primary odor-causing substances. In summary, emissions of VOCs from rubber industrial processes not only pose substantial health risks to workers but also contribute significantly to odor pollution. Consequently, enterprises must prioritize optimizing workplace conditions to ensure the occupational health and well-being of their employees.

Graphene-Infused Sustainable Rubber-Based Triboelectric Nanogenerator For Real-Time Human Motion Monitoring.

Triboelectric nanogenerators (TENG) are promising alternatives for clean energy harvesting. However, the material utilization in the development of TENG relies majorly on polymers derived from non-renewable resources. Therefore, minimizing the carbon footprint associated with such TENG development demands a shift toward usage of sustainable materials. This study pioneers using natural rubber (NR) as a sustainable alternative in TENG development. Infusing graphene in NR, its dielectric constant and tribonegativity are optimized, yielding a remarkable enhancement. The optimized sample exhibits a dielectric constant of 411 (at 103 Hz) and a contact potential difference (CPD) value of 1.85 V. In contrast, the pristine NR sample showed values of 6 and 3.06 V for the dielectric constant and CPD. Simulation and experimental studies fine-tune the TENG's performance, demonstrating excellent agreement between theoretical predictions and practical studies. Sensors developed via stencil printing technique possess a remarkably low layer thickness of 270 µm, and boast a power density of 420 mW m-2, a staggering 250% increase over conventional NR. Moreover, the material is pressure sensitive, enabling precise real-time human motion detection, including finger contact, finger bending, neck bending, and arm bending. This versatile sensor offers wireless monitoring, empowering healthcare monitoring based on the Internet of Things.

Endoscopic polidocanol foam sclerobanding for the treatment of grade II-III internal hemorrhoids: A prospective, multi-center, randomized study.

BACKGROUND: Endoscopic rubber band ligation (ERBL) is a nonsurgical technique for the treatment of symptomatic internal hemorrhoids but is limited by recurrence and post-procedural pain. AIM: To evaluate satisfaction, long-term recurrence, and post-procedural pain in managing internal hemorrhoids using a combination of polidocanol foam sclerotherapy and ERBL. METHODS: This was a prospective, multicenter, randomized study. A total of 195 consecutive patients diagnosed with grade II-III internal hemorrhoids were enrolled from four tertiary hospitals and randomly divided into a cap-assisted endoscopic polidocanol foam sclerobanding (EFSB) or an ERBL group. All patients were followed-up for 12 months. Symptom-based severity and post-procedural pain were assessed using a hemorrhoid severity score (HSS) and a visual analog scale (VAS). Continuous variables were reported as medians and interquartile range. RESULTS: One hundred and ninety-five patients were enrolled, with 98 in the EFSB group. HSS was lower in the EFSB group than in the ERBL group at 8 weeks [4.0 (3.0-5.0) vs 5.0 (4.0-6.0), P = 0.003] and 12-month [2.0 (1.0-3.0) vs 3.0 (2.0-3.0), P < 0.001] of follow-up. The prolapse recurrence rate was lower in the EFSB group at 12 months (11.2% vs 21.6%, P = 0.038). Multiple linear regression analysis demonstrated that EFSB treatment [B = -0.915, 95% confidence interval (CI): -1.301 to -0.530, P = 0.001] and rubber band number (B = 0.843, 95%CI: 0.595-1.092, P < 0.001) were negatively and independently associated with the VAS score 24 hours post-procedure. The median VAS was lower in the EFSB group than in the ERBL [2.0 (1.0-3.0) vs 3.0 (2.0-4.0), P < 0.001]. CONCLUSION: Cap-assisted EFSB provided long-term satisfaction and effective relief from the recurrence of prolapse and pain 24 hours post-procedure.

A multicenter, open-label, parallel-group, randomized controlled trial of Tongluo-Qutong rubber plaster for the treatment of cervical spondylotic radiculopathy.

BACKGROUND: In China, Tongluo-Qutong rubber plaster (TQRP) is commonly used for cervical spondylotic radiculopathy, but lacks high-quality trials. OBJECTIVE: This study aimed to conduct a multicenter, open-label, parallel-group, randomized controlled trial in China to investigate the practical efficacy and safety of TQRP in the treatment of CSR. METHODS: A total of 240 patients diagnosed with CSR were recruited for the investigation from multiple hospitals in Gansu province, China. The patients were randomly assigned to either an experimental or a control group. The experimental group received treatment with TQRP, whereas the control group was administered a diclofenac sodium patch (DSP) for a maximum duration of 21 days. The visual analogue scale (VAS) score for pain, the proportion of patients experiencing 50% or more pain relief, the neck disability index (NDI), changes as per the Eaton trial, and recurrence during the follow-up period were evaluated for both groups. The safety and adverse events associated with the concurrent drug therapy were also evaluated. RESULTS: At each time point, the mean VAS and NDI scores of both groups demonstrated a downward trend. The experimental group exhibited a greater decline in VAS score at each time point compared to the control group (P< 0.01). In the Eaton trial, both the percentage of patients experiencing pain relief of 50% or more and the number of abnormal results exhibited improvement. However, the outcomes in the 21 ± 3d experimental group were significantly superior to those in the control group (P< 0.01). During the follow-up period, the recurrence events in the experimental group were reduced compared to the control group. The difference between the two groups was statistically significant (P< 0.05). The incidence of adverse reactions was 1.74% for TQRP and 3.54% for DSP. CONCLUSION: TQRP is effective and safe in the treatment of CSR.

High toughness and fast home-compost biodegradable packaging films derived from polylactic acid/thermoplastic starch/para-rubber ternary blends.

This research aims to formulate biobased and biodegradable packaging films with high toughness and fast home-compost biodegradation using ternary blends of polylactic acid (PLA), Para rubber (NR), and thermoplastic starch (TPS) through blown-film extrusion. The TPS content in this work ranges from 5 to 20 wt%, while the PLA: NR ratio is fixed at 70:30. At this PLA: NR ratio, the blend with 10 wt% TPS (PNT10) exhibited the highest % elongation at break and tensile toughness. Peroxide radical initiator was investigated as a potential additive for improving the properties of the ternary blend. Our binary interaction study indicated that peroxide initiated grafting reactions of PLA-NR and NR-TPS pairs, while no grafting occurred between PLA and TPS. In ternary blends, the highest peroxide content (0.5 wt%) increased the % elongation at break up to 120%, with the tensile toughness reaching 7255 MJ/m3. The improved compatibility induced by peroxide addition was supported by enhanced dispersion of TPS in the PLA/NR matrices. Results from the room-temperature soil burial test indicated that the presence of TPS could significantly accelerate the home-compost degradation of PNT films compared to films produced from neat PLA and PLA/NR. This suggests its potential as both a cost reducer and a biodegradation accelerator.

TkJAZs-TkMYC2-TkSRPP/REF Regulates the Biosynthesis of Natural Rubber in Taraxacum kok-saghyz.

Taraxacum kok-saghyz (TKS) is a natural rubber (NR)-producing plant and a model plant for studying the biosynthesis of NR. Analyzing and studying the biosynthetic mechanism of NR is an important way to cultivate high-yield rubber TKS varieties. JAZ proteins, which belong to the Jasmonate ZIM domain family, function as negative regulators in the jasmonic acid (JA) signal transduction pathway. MYC2 is typically regarded as a regulatory factor for the target genes of JAZ proteins; JAZ proteins indirectly influence the gene expression regulated by MYC2 by modulating its activity. Theoretically, JAZ is expected to participate in growth, development, and responses to environmental cues related to rubber and biomass accumulation in TKS, all of which rely on the interaction between JAZ and MYC2. In this study, we identified 11 TkJAZs through homology searching of the TKS genomes and bioinformatics analyses. Subcellular localization, Y2H, and BiFC analysis demonstrate that TkJAZs and TkMYC2 are localized in the nucleus, with all TkJAZs and TkMYC2 showing nuclear colocalization interactions. Overexpression of TkMYC2 in TKS inhibited leaf development, promoted root growth, and simultaneously increased NR production. RNA-seq and qRT-PCR analysis revealed that the TkSRPP/REF genes exhibit varying degrees of upregulation compared to the wild type, upregulating the TkREF1 gene by 3.7-fold, suggesting that TkMYC2 regulates the synthesis of NR by modulating the TkSRPP/REF genes.

Study on the Tribological Properties of Multilayer Concentric Hexagonal Laser Texturing on Rubber Surfaces of Screw Pumps.

Given the friction and drag reduction effects observed in various biological hexagonal structures in nature, a new design was implemented on the rubber surface of the stator of a submersible screw pump. This design featured a multilayer concentric hexagonal groove structure. Furthermore, a composite multilayer hexagonal structure integrating grooves and pits was also developed and applied. This study investigated the influence of groove layer number, groove depth, pit depth, and multilayer hexagonal groove texture arrangement on the rubber surface flow characteristics. Additionally, the pressure field state, the degree of influence on the oil film-bearing capacity, and the biomimetic and hydrodynamic lubrication theories were tested using the finite element analysis method. Tribological experiments were conducted on nanosecond laser-processed rubber textures under simulated liquid lubrication conditions, reflecting actual shale oil well experiments. These experiments aimed to investigate the influence of multilayer hexagonal shape parameters on the tribological characteristics of the stator-rotor friction pair of a submersible screw pump. The results indicated that with a constant overall size, a multilayer hexagonal structure with ~0.1 mm groove depth enhanced the oil film-bearing capacity, providing significant friction and drag reduction. For composite textures, a deeper pit depth within the study area enhanced the oil film-bearing capacity. Furthermore, a gradient arrangement of groove textures featuring wider outer grooves and shallower depth exhibited superior performance in terms of bearing capacity.

Hydroxyapatite-Filled Acrylonitrile-Butadiene Rubber Composites with Improved Cure Characteristics and Reduced Flammability.

The goal of this work was to develop acrylonitrile-butadiene (NBR) elastomer composites filled with hydroxyapatite (HAP) characterized by improved cure characteristics and resistance to burning. Silane, i.e., (3-aminopropyl)-triethoxysilane, ionic liquid, i.e., 1-decyl-3-methylimidazolium bromide and surfactant, i.e., cetyltrimethylammonium bromide, were used to improve the filler's dispersibility in the elastomer matrix and to reduce the time and temperature of vulcanization. The effects of HAP and dispersants on the cure characteristics, crosslink density and physico-chemical properties of NBR composites were explored. The additives used, especially the ionic liquid and surfactant, effectively improved the dispersion of HAP in the NBR matrix. The amount of HAP and the dispersant used strongly affected the cure characteristics and crosslink density of NBR. The optimal vulcanization time significantly increased with HAP content and was pronouncedly reduced when ionic liquid and surfactant were applied. In addition, ionic liquid and surfactant significantly lowered the onset vulcanization temperature and improved the crosslink density and hardness of the vulcanizates while impairing their elasticity. HAP and dispersants did not significantly affect the damping properties or chemical resistance of NBR vulcanizates. Above all, application of HAP considerably enhanced the resistance of vulcanizates to thermo-oxidative aging and reduced their flammability compared with the unfilled NBR.

Characterization of WO3/Silicone Rubber Composites for Hydrogen-Sensitive Gasochromic Application.

WO3 and silicone rubber (SR)-based gasochromic composites were fabricated to detect hydrogen leaks at room temperature. WO3 rod-like nanostructures were uniformly distributed in the SR matrix, with a particle size of 60-100 nm. The hydrogen permeability of these composites reached 1.77 cm3·cm/cm2·s·cmHg. At a 10% hydrogen concentration, the visible light reflectance of the composite decreased 49% during about 40 s, with a color change rate of 6.4% s-1. Moreover, the composite detected hydrogen concentrations as low as 0.1%. And a color scale was obtained for easily assessing hydrogen concentrations in the environment based on the color of composites. Finally, the composite materials as disposable sensors underwent testing at several Sinopec hydrogen refueling stations.

Comparing the Efficacy of 5% EMLA Cream and 20% Benzocaine Gel on Gingival Tissue Surrounding Non-Carious Cervical Lesions for Reduction of Pain Following Rubber Dam Clamp Placement: A Split-Mouth Randomized Clinical Trial.

Aim The aim of this study was to evaluate the effectiveness of 5% eutectic mixture of local anesthetics (EMLA) cream and 20% benzocaine gel in reduction of pain during rubber dam clamp placement in the treatment of non-carious cervical lesions (NCCLs). Methodology In this split-mouth single-blind randomized clinical trial, 50 adult participants were selected from the outpatient department. The test group was treated using 5% EMLA cream for three minutes, and visual analog scale (VAS) scores were recorded. The comparison group was treated using 20% benzocaine gel and procedure was repeated as that in the test group. After recording the VAS scores, NCCLs in both the groups were restored using composite restoration. Results In the included 50 participants, 70% were males, with an age group of 31-67 years. The mean VAS score at 3 minutes in EMLA group was significantly lower than that in benzocaine group. Conclusion Application of 5% EMLA cream for 3 minutes showed greater pain reduction during rubber dam clamp placement as compared to 20% benzocaine gel in adult patients with NCCLs.

Facile preparation and characterization of biodegradable and biocompatible UV shielding transdermal patches based on natural rubber latex- dextrin blends.

The physico-chemical and biological properties of natural rubber latex (NRL), entailing its biodegradability and biocompatibility, render it a promising material for various biomedical applications. This research explores the facile blending of NRL with dextrin in different compositions to investigate its potential as a prospective UV shielding transdermal patch for biomedical applications. The superior compatibility between the polymers after blending and the improved thermal stability have been established through FTIR, DSC, and TGA examinations, respectively. Optimization of blended polymers for compatibility, wettability, crystallinity, and static mechanical properties has been performed. Morphology characterization conducted via SEM and AFM techniques suggests a uniform morphology for the optimized blend system. The UV shielding ability of the blend has been confirmed by the evaluation of in-vitro UV shielding performance, UV protection factor (UPF), and the superior protection of the optimized system on living cells upon UV irradiation. The observed cell viability, swelling, erosion, porosity, hemocompatibility, and soil degradation properties suggest the NRL-DXT combination for the possible development of high-quality transdermal patches.