ABSTRACT
High open-circuit voltage (Voc) organic solar cells (OSCs) have received increasing attention because of their promising application in tandem devices and indoor photovoltaics. However, the lack of a precise correlation between molecular structure and stacking behaviors of wide band gap electron acceptors has greatly limited its development. Here, we adopted an asymmetric halogenation strategy (AHS) and synthesized two completely non-fused ring electron acceptors (NFREAs), HF-BTA33 and HCl-BTA33. The results show that AHS significantly enhances the molecular dipoles and suppresses electron-phonon coupling, resulting in enhanced intramolecular/intermolecular interactions and decreased nonradiative decay. As a result, PTQ10 : HF-BTA33 realizes a power conversion efficiency (PCE) of 11.42 % with a Voc of 1.232â V, higher than that of symmetric analogue F-BTA33 (PCE=10.02 %, Voc=1.197â V). Notably, PTQ10 : HCl-BTA33 achieves the highest PCE of 12.54 % with a Voc of 1.201â V due to the long-range ordered π-π packing and enhanced surface electrostatic interactions thereby facilitating exciton dissociation and charge transport. This work not only proves that asymmetric halogenation of completely NFREAs is a simple and effective strategy for achieving both high PCE and Voc, but also provides deeper insights for the precise molecular design of low cost completely NFREAs.
ABSTRACT
Supramolecular chiral organization gives π-conjugated molecules access to fascinating specific interactions with circularly polarized light (CPL). Such a feature enables the fabrication of high-performance chiral organic electronic devices that detect or emit CPL directly. Herein, it is shown that chiral fused-ring electron-acceptor BTP-4F single-crystal-based phototransistors demonstrate distinguished CPL discrimination capability with current dissymmetry factor exceeding 1.4, one of the highest values among state-of-the-art direct CPL detectors. Theoretical calculations prove that the chirality at the supramolecular level in these enantiomeric single crystals originates from chiral exciton coupling of a unique quasi-2D supramolecular organization consisting of interlaced molecules with opposite helical conformation. Impressively, such supramolecular organization produces a higher dissymmetry factor along the preferred growth direction of the chiral single crystals in comparison to that of the short axis direction. Furthermore, the amplified, inverted, and also anisotropic current dissymmetry compared to optical dissymmetry is studied by finite element simulations. Therefore, a unique chiral supramolecular organization that is responsible for the excellent chiroptical response and anisotropic electronic properties is developed, which not only enables the construction of high-performance CPL detection devices but also allows a better understanding of the structure-property relationships in chiral organic optoelectronics.
ABSTRACT
Organic solar cells (OSCs) have attracted wide research attention in the past decades. Very recently, oligomerized fused-ring electron acceptors (OFREAs) have emerged as a promising alternative to small-molecular/polymeric acceptor-based OSCs due to their unique advantages such as well-defined structures, batch reproducibility, good film formation, low diffusion coefficient, and excellent stability. So far, rapid advances have been made in the development of OFREAs consisting of directly/rigidly/flexibly linked oligomers and fused ones. In this Minireview, we systematically summarized the recent research progress of OFREAs, including structural diversity, synthesis approach, molecular conformation and packing, and long-term stability. Finally, we conclude with future perspectives on the challenges to be addressed and potential research directions. We believe that this Minireview will encourage the development of novel OFREAs for OSC applications.
ABSTRACT
Efficient exciton diffusion and charge transport play a vital role in advancing the power conversion efficiency (PCE) of organic solar cells (OSCs). Here, a facile strategy is presented to simultaneously enhance exciton/charge transport of the widely studied PM6:Y6-based OSCs by employing highly emissive trans-bis(dimesitylboron)stilbene (BBS) as a solid additive. BBS transforms the emissive sites from a more H-type aggregate into a more J-type aggregate, which benefits the resonance energy transfer for PM6 exciton diffusion and energy transfer from PM6 to Y6. Transient gated photoluminescence spectroscopy measurements indicate that addition of BBS improves the exciton diffusion coefficient of PM6 and the dissociation of PM6 excitons in the PM6:Y6:BBS film. Transient absorption spectroscopy measurements confirm faster charge generation in PM6:Y6:BBS. Moreover, BBS helps improve Y6 crystallization, and current-sensing atomic force microscopy characterization reveals an improved charge-carrier diffusion length in PM6:Y6:BBS. Owing to the enhanced exciton diffusion, exciton dissociation, charge generation, and charge transport, as well as reduced charge recombination and energy loss, a higher PCE of 17.6% with simultaneously improved open-circuit voltage, short-circuit current density, and fill factor is achieved for the PM6:Y6:BBS devices compared to the devices without BBS (16.2%).
ABSTRACT
Fine-tuning the crystallinity and self-aggregation features of donors/acceptor materials toward high-efficiency organic solar cells (OSCs) is of crucial importance. Here, a convenient yet effective way to simultaneously control the crystallinity and self-aggregation of the fused ring electron acceptor (FREA) is demonstrated by altering the length of the first-position branched alkyl chain on the cyclic unit. Specifically, three carbazole-based FREAs, 4TC-4F-C6C6, 4TC-4F-C8C8, and 4TC-4F-C10C10, are synthesized by changing the length of the first-position branched alkyl chain on the carbazole unit. The crystallinity of the studied acceptors decreases as the branched alkyl chain is lengthened. The ability of the acceptors to undergo self-aggregation decreases in the order 4TC-4F-C10C10, 4TC-4F-C6C6, and 4TC-4F-C8C8. The medium crystallinity and lower self-aggregation properties of 4TC-4F-C8C8 result in favorable phase separation when blended with poly-[(2,6-(4,8-bis(5-(2-ethylhexyl-3-fluoro)thiophen-2-yl)-benzo[1,2-b:4,5-b']dithiophene))-alt-(5,5-(1',3'-di-2-thienyl-5',7'-bis(2-ethylhexyl)benzo[1',2'-c:4',5'-c']dithiophene-4,8-dione))] (PM6), which is conducive to effective exciton dissociation and charge transport. Consequently, the OSC device based on PM6:4TC-4F-C8C8 delivers the best power conversion efficiency of 14.85%.
ABSTRACT
The A-DA'D-A fused-ring electron acceptors with an angular fusion mode and electron-deficient core has significantly boosted organic photovoltaic efficiency. Here, the intrinsic role of the peculiar structure is revealed by comparing representative A-DA'D-A acceptor Y6 with its A-D-A counterparts having different fusion modes. Owing to the more delocalized HOMO and deeper LUMO level, Y6 exhibits stronger and red-shifted absorption relative to the linear and angular fused A-D-A acceptors, respectively. Moreover, the change from linear to angular fusion substantially reduces the electron-vibration couplings, which is responsible for the faster exciton diffusion, exciton dissociation, and electron transport for Y6 than the linear fused A-D-A acceptor. Notably, the electron-vibration coupling for exciton dissociation is further decreased by introducing the electron-deficient core, thus contributing to the efficient charge generation under low driving forces in the Y6-based devices.
ABSTRACT
The innovation of high-performance fused-ring electron acceptors (FREAs) has carried the field of organic solar cells (OSCs) toward a new stage of development. However, due to high synthetic complexity and production costs, FREAs may not be the most promising candidates for future commercialization applications. To address these disadvantages of FREAs, a series of low-cost acceptors, named as noncovalently FREAs (NFREAs), is successfully constructed by employing the strategy of noncovalently conformational locks. Herein, a novel NFREA (BDTO-4F) based on 3,7-dialkyloxybenzo[1,2-b:4,5-b']dithiophene is synthesized and fully characterized. Benefiting from the complementary absorption of the donor and acceptor, balanced charge transport, and favorable film morphology, J52:BDTO-4F based OSCs afford a satisfied power conversion efficiency of 12.09%, much higher than PBDB-T:BDTO-4F-based devices (8.30%). It is worth mentioning that BDTO-4F possesses a higher figure-of-merit value of 55.65 in comparison with several representative FREAs based on a cost-efficiency evaluation. This work demonstrates the potential of the novel benzo[1,2-b:4,5-bâ³]dithiophene derivative for constructing low-cost and high-performance NFREAs, providing a valuable insight on the materials design.
ABSTRACT
Two new fused-ring electron acceptor (FREA) isomers with nonlinear and linear molecular conformation, m-BAIDIC and p-BAIDIC, are designed and synthesized. Despite the similar light absorption range and energy levels, the two isomers exhibit distinct electron reorganization energies and molecular packing motifs, which are directly related to the molecular conformation. Compared with the nonlinear acceptor, the linear p-BAIDIC shows more ordered molecular packing and higher crystallinity. Furthermore, p-BAIDIC-based devices exhibit reduced nonradiative energy loss and improved charge transport mobilities. It is beneficial to enhance the open-circuit voltage (VOC ) and short-current current density (JSC ) of the devices. Therefore, the linear FREA, p-BAIDIC yields a relatively higher efficiency of 7.71% in the binary device with PM6, in comparison with the nonlinear m-BAIDIC. When p-BAIDIC is incorporated into the binary PM6/BO-4Cl system to form a ternary system, synergistic enhancements in VOC , JSC , fill factor (FF), and ultimately a high efficiency of 17.6% are achieved.
ABSTRACT
Small donor molecules based on fused ring acceptors exhibit encouraging photovoltaic properties and expeditious advancement in organic solar cells. Central core modification of non-fullerene acceptor materials is a favorable methodology to enhance electronic properties and efficiency for OSCs. Herein, four new donor molecules, namely, BDTM1, PYRM2, ANTM3, and NM4 are designed with a strong donor moiety triphenylamine, tetracyanobutadiene as acceptor unit, and thiophene as spacer linked to a modified central core. Geometric parameters, optical, electrical properties, effect of central core modification on tailored molecules BDTM1-NM4 are investigated and compared with reference DPPR. DFT together with TDDFT approaches using MPW1PW91 functional is used to study key parameters like absorption maximum (λmax), frontier molecular approach, ionization potential, electron affinity, the density of states, transition density matrix along with open-circuit voltage (VOC), dipole moment and reorganization energy. Among all these molecules, BDTM1 shows maximum calculated absorption λmax (817 nm) and the lowest band gap (2.54 eV). This bathochromic shift in BDTM1 is due to the presence of 4,8-dimethoxy-2,6-di-2-thienylbenzodithiophene as a strong electron-withdrawing group. Computed reorganization energies (RE) shows that BDTM1 has the highest hole and electron mobility among all designed molecules. Combination of BDTM1 donor and PC61BM acceptor further verifies charge transfer and their interaction. The results illustrate that designed donor molecules (BDTM1-NM4) are better in performance and are recommended for experimentation to develop efficient OSCs. Four new donor molecules, namely, BDTM1, PYRM2, ANTM3, and NM4 are designed with a strong donor moiety triphenylamine, tetracyanobutadiene as acceptor unit and thiophene as spacer linked to a modified central core. Geometric parameters, optical, electrical properties, effect of central core modification on tailored molecules BDTM1-NM4 are investigated and compared with reference DPPR.
ABSTRACT
Side-chain engineering is an effective strategy to regulate the solubility and packing behavior of organic materials. Recently, a unique strategy, so-called terminal side-chain (T-SC) engineering, has attracted much attention in the field of organic solar cells (OSCs), but there is a lack of deep understanding of the mechanism. Herein, a new noncovalently fused-ring electron acceptor (NFREA) containing two T-SCs (NoCA-5) was designed and synthesized. Introduction of T-SCs can enhance molecular rigidity and intermolecular π-π stacking, which is confirmed by the smaller Stokes shift value, lower reorganization free energy, and shorter π-π stacking distance in comparison to NoCA-1. Hence, the NoCA-5-based device exhibits a record power conversion efficiency (PCE) of 14.82 % in labs and a certified PCE of 14.5 %, resulting from a high electron mobility, a short charge-extraction time, a small Urbach energy (Eu ), and a favorable phase separation.
ABSTRACT
Noncovalently fused-ring electron acceptors (NFREAs) have attracted much attention in recent years owing to their advantages of simple synthetic routes, high yields and low costs. However, the efficiencies of NFREAs based organic solar cells (OSCs) are still far behind those of fused-ring electron acceptors (FREAs). Herein, a series of NFREAs with Sâ â â O noncovalent intramolecular interactions were designed and synthesized with a two-step synthetic route. Upon introducing π-extended end-groups into the backbones, the electronic properties, charge transport, film morphology, and energy loss were precisely tuned by fine-tuning the degree of multi-fluorination. As a result, a record PCE of 14.53 % in labs and a certified PCE of 13.8 % for NFREAs based devices were obtained. This contribution demonstrated that combining the strategies of noncovalent conformational locks and π-extended end-group engineering is a simple and effective way to explore high-performance NFREAs.
ABSTRACT
The introduction of the IDIC/ITIC families of non-fullerene acceptors has boosted the photovoltaic performances of bulk-heterojunction organic solar cells. The fine tuning of the photophysical, morphological and processability properties with the aim of reaching higher and higher photocurrent efficiencies has prompted uninterrupted worldwide research on these peculiar families of organic compounds. The main strategies for the modification of IDIC/ITIC compounds, described in several contributions published in the past few years, can be summarized and classified into core modification strategies and end-capping group modification strategies. In this review, we analyze the more recent advances in this field (last two years), and we focus our attention on the molecular design proposed to increase photovoltaic performance with the aim of rationalizing the general properties of these families of non-fullerene acceptors.
Subject(s)
Electric Power Supplies , Fullerenes/chemistry , Photochemical Processes , Solar Energy , HumansABSTRACT
A new fluorinated electron acceptor (FINIC) based on 6,6,12,12-tetrakis(3-fluoro-4-hexylphenyl)-indacenobis(dithieno[3,2-b;2',3'-d]thiophene) as the electron-donating central core and 5,6-difluoro-3-(1,1-dicyanomethylene)-1-indanone as the electron-deficient end groups is rationally designed and synthesized. FINIC shows similar absorption profile in dilute solution to the nonfluorinated analogue INIC. However, compared with INIC, FINIC film shows red-shifted absorption, down-shifted frontier molecular orbital energy levels, enhanced crystallinity, and more ordered molecular packing. Single-crystal structure data show that FINIC molecules pack into closer 3D "network" motif through H-bonding and π-π interaction, while INIC molecules pack into incompact "honeycomb" motif through only π-π stacking. Theoretical calculations reveal that FINIC has stronger electronic coupling and more molecular interactions than INIC. FINIC has higher electron mobilities in both horizontal and vertical directions than INIC. Moreover, FINIC and INIC support efficient 3D exciton transport. PBD-SF/FINIC blend has a larger driving force for exciton splitting, more efficient charge transfer and photoinduced charge generation. Finally, the organic solar cells based on PBD-SF/FINIC blend yield power conversion efficiency of 14.0%, far exceeding that of the PBD-SF/INIC-based devices (5.1%).
ABSTRACT
Classical fused-ring electron acceptors (FREAs) with a linear acceptor-donor-acceptor (A-D-A) architecture continuously break records of power conversion efficiency (PCE) in nonfullerene organic solar cells. In contrast, the development of star-shaped FREAs still lags behind. Herein, a new C3h-symmetric and electron-rich core, benzotri(cyclopentadithiophene) (BTCDT) in which the central benzo[1,2-b:3,4-b':5,6-bâ³]trithiophene fused with three outer thiophenes via three cyclopentadienyl rings, is synthesized and used for the construction of star-shaped FREAs (BTCDT-IC and BTCDT-ICF). Owing to the strong electron-donating ability of the BTCDT unit, both acceptors exhibit the effective intramolecular charge transfer, leading to the strong absorption in the region of 500-800 nm with narrow band gaps below 1.70 eV as well as suitable highest occupied molecular orbital and lowest unoccupied molecular orbital levels. Compared with nonfluorinated BTCDT-IC, fluorinated BTCDT-ICF red-shifts the absorption peak to 688 nm and reduces the band gap to 1.62 eV, which induces a broader external quantum efficiency (EQE) response ranging from 300 to 800 nm and a higher maximum EQE of 70% while blending with a wide band gap polymer donor J61. The J61:the BTCDT-ICF blend film exhibits more suitable phase morphology compared with the J61:BTCDT-IC blend film, which is responsible for the enhanced EQE value, increased short-circuit current density (JSC), and fill factor (FF) in organic solar cell devices. As a result, the J61:BTCDT-ICF-based device yields a best PCE of 8.11% with a high JSC of 16.93 mA cm-2 and a high FF of 65.6%, demonstrating that the BTCDT-based star-shaped FREAs hold great potential for nonfullerene organic solar cells.
ABSTRACT
The quest for sustainable energy sources has led to accelerated growth in research of organic solar cells (OSCs). A solution-processed bulk-heterojunction (BHJ) OSC generally contains a donor and expensive fullerene acceptors (FAs). The last 20 years have been devoted by the OSC community to developing donor materials, specifically low bandgap polymers, to complement FAs in BHJs. The current improvement from ≈2.5% in 2013 to 17.3% in 2018 in OSC performance is primarily credited to novel nonfullerene acceptors (NFA), especially fused ring electron acceptors (FREAs). FREAs offer unique advantages over FAs, like broad absorption of solar radiation, and they can be extensively chemically manipulated to tune optoelectronic and morphological properties. Herein, the current status in FREA-based OSCs is summarized, such as design strategies for both wide and narrow bandgap FREAs for BHJ, all-small-molecule OSCs, semi-transparent OSC, ternary, and tandem solar cells. The photovoltaics parameters for FREAs are summarized and discussed. The focus is on the various FREA structures and their role in optical and morphological tuning. Besides, the advantages and drawbacks of both FAs and NFAs are discussed. Finally, an outlook in the field of FREA-OSCs for future material design and challenges ahead is provided.
ABSTRACT
Fused-ring electron acceptors (FREAs), as a family of non-fullerene (NF) acceptors, have achieved tremendous success in pushing the power conversion efficiency of organic solar cells. Here, the detailed molecular packing motifs of two extensively studied FREAs-ITIC and ITIC-Th are reported. It is revealed for the first time the long-range structure ordering along the backbone direction originated from favored end group π-π stacking. The backbone ordering could be significantly enhanced in the ternary film by the mutual mixing of ITIC and ITIC-Th, which gives rise to an improved in-plane electron mobility and better ternary device performance. The backbone ordering might be a common morphological feature of FREAs, providing explanations to previously observed small open circuit voltage loss and superior performance of FREA-based devices and guiding the future molecular design of high-performance NF acceptors.
ABSTRACT
Relative to electron donors for bulk heterojunction organic solar cells (OSCs), electron acceptors that absorb strongly in the visible and even near-infrared region are less well developed, which hinders the further development of OSCs. Fullerenes as traditional electron acceptors have relatively weak visible absorption and limited electronic tunability, which constrains the optical and electronic properties required of the donor. Here, high-performance fullerene-free OSCs based on a combination of a medium-bandgap polymer donor (FTAZ) and a narrow-bandgap nonfullerene acceptor (IDIC), which exhibit complementary absorption, matched energy levels, and blend with pure phases on the exciton diffusion length scale, are reported. The single-junction OSCs based on the FTAZ:IDIC blend exhibit power conversion efficiencies up to 12.5% with a certified value of 12.14%. Transient absorption spectroscopy reveals that exciting either the donor or the acceptor component efficiently generates mobile charges, which do not suffer from recombination to triplet states. Balancing photocurrent generation between the donor and nonfullerene acceptor removes undesirable constraints on the donor imposed by fullerene derivatives, opening a new avenue toward even higher efficiency for OSCs.
ABSTRACT
Naphtho[1,2-b:5,6-b']dithiophene is extended to a fused octacyclic building block, which is end capped by strong electron-withdrawing 2-(5,6-difluoro-3-oxo-2,3-dihydro-1H-inden-1-ylidene)malononitrile to yield a fused-ring electron acceptor (IOIC2) for organic solar cells (OSCs). Relative to naphthalene-based IHIC2, naphthodithiophene-based IOIC2 with a larger π-conjugation and a stronger electron-donating core shows a higher lowest unoccupied molecular orbital energy level (IOIC2: -3.78 eV vs IHIC2: -3.86 eV), broader absorption with a smaller optical bandgap (IOIC2: 1.55 eV vs IHIC2: 1.66 eV), and a higher electron mobility (IOIC2: 1.0 × 10-3 cm2 V-1 s-1 vs IHIC2: 5.0 × 10-4 cm2 V-1 s-1 ). Thus, IOIC2-based OSCs show higher values in open-circuit voltage, short-circuit current density, fill factor, and thereby much higher power conversion efficiency (PCE) values than those of the IHIC2-based counterpart. In particular, as-cast OSCs based on FTAZ: IOIC2 yield PCEs of up to 11.2%, higher than that of the control devices based on FTAZ: IHIC2 (7.45%). Furthermore, by using 0.2% 1,8-diiodooctane as the processing additive, a PCE of 12.3% is achieved from the FTAZ:IOIC2-based devices, higher than that of the FTAZ:IHIC2-based devices (7.31%). These results indicate that incorporating extended conjugation into the electron-donating fused-ring units in nonfullerene acceptors is a promising strategy for designing high-performance electron acceptors.
ABSTRACT
A fused hexacyclic electron acceptor, IHIC, based on strong electron-donating group dithienocyclopentathieno[3,2-b]thiophene flanked by strong electron-withdrawing group 1,1-dicyanomethylene-3-indanone, is designed, synthesized, and applied in semitransparent organic solar cells (ST-OSCs). IHIC exhibits strong near-infrared absorption with extinction coefficients of up to 1.6 × 105 m-1 cm-1 , a narrow optical bandgap of 1.38 eV, and a high electron mobility of 2.4 × 10-3 cm2 V-1 s-1 . The ST-OSCs based on blends of a narrow-bandgap polymer donor PTB7-Th and narrow-bandgap IHIC acceptor exhibit a champion power conversion efficiency of 9.77% with an average visible transmittance of 36% and excellent device stability; this efficiency is much higher than any single-junction and tandem ST-OSCs reported in the literature.
ABSTRACT
A new fluorinated nonfullerene acceptor, ITIC-Th1, has been designed and synthesized by introducing fluorine (F) atoms onto the end-capping group 1,1-dicyanomethylene-3-indanone (IC). On the one hand, incorporation of F would improve intramolecular interaction, enhance the push-pull effect between the donor unit indacenodithieno[3,2-b]thiophene and the acceptor unit IC due to electron-withdrawing effect of F, and finally adjust energy levels and reduce bandgap, which is beneficial to light harvesting and enhancing short-circuit current density (JSC ). On the other hand, incorporation of F would improve intermolecular interactions through CF···S, CF···H, and CF···π noncovalent interactions and enhance electron mobility, which is beneficial to enhancing JSC and fill factor. Indeed, the results show that fluorinated ITIC-Th1 exhibits redshifted absorption, smaller optical bandgap, and higher electron mobility than the nonfluorinated ITIC-Th. Furthermore, nonfullerene organic solar cells (OSCs) based on fluorinated ITIC-Th1 electron acceptor and a wide-bandgap polymer donor FTAZ based on benzodithiophene and benzotriazole exhibit power conversion efficiency (PCE) as high as 12.1%, significantly higher than that of nonfluorinated ITIC-Th (8.88%). The PCE of 12.1% is the highest in fullerene and nonfullerene-based single-junction binary-blend OSCs. Moreover, the OSCs based on FTAZ:ITIC-Th1 show much better efficiency and better stability than the control devices based on FTAZ:PC71 BM (PCE = 5.22%).