Li-Ga Alloy-Contained Hybrid Solid Electrolyte Interphase Induced by In Situ Polymerization for High-Performance Lithium Metal Batteries.

Construction of quasi-solid-state lithium metal batteries (LMBs) by in situ polymerization is considered a key strategy for the next generation of energy storage systems with high specific energy and safety. Poly(1,3-dioxolane) (PDOL)-based electrolytes have attracted wide attention among researchers, benefiting from the low cost and high ionic conductivity. However, interfacial deterioration and uncontrollable growth of lithium dendrites easily appeared in LMBs due to the high reactivity of lithium metal, resulting in the failure of LMBs. In this work, a strategy is developed of using Ga(OTF)3 as the initiator to obtain a PDOL-based gel electrolyte (GaPD). In addition, a hybrid stable solid electrolyte interphase (SEI) of lithium fluoride/Li2O/Li-Ga alloys is observed on the surface of lithium metal. Combined with density functional theory calculations, the hybrid SEI shows high affinity toward Li+, indicating that a uniform deposition of Li+ could be achieved. Therefore, the Li/GaPD/Li cell operates stably for 1600 h at room temperature. In addition, the LiFePO4/GaPD/Li cell retains a capacity retention rate of 90.2% over 200 cycles at 1 C. This work provides a reference for the practical application of in situ polymerization technology in high-performance and safe LMBs.

Supramolecular polymer cross-linking gel electrolyte for highly stable quasi-solid-state lithium metal batteries.

Lithium (Li) metal batteries have the advantage of high energy density, but the Li dendrites risk piercing the separator and causing a short circuit in the battery. Replacing the liquid electrolytes with gel electrolytes is considered an effective strategy to solve the issues. Herein, a poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP)-based gel electrolyte, improved with multifunctional supramolecular polymer (MSP), was prepared to enhance the cycling stability and energy density of quasi-solid-state Li metal batteries. The MSP addictive constructs a cross-linked network structure with PVDF-HFP matrix and lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) through hydrogen bonding, improving the mechanical strength of the composite gel electrolyte (PH-10%MSP-GE) to against the growth of Li dendrites. Moreover, the pre-lithiated sulfonic acid groups, conductive polyether groups of MSP, and the attraction of TFSI- anions, promote the Li-ion transportation of the composite gel electrolyte. Finally, the Li||Li symmetric cell cycle stably for over 450 h. The Li||LiFePO4 full cell demonstrates a high energy density and excellent cycling stability for over 600 cycles, with a capacity retention rate of up to 98.7%. This work provides valuable insights into the preparation of multifunctional composite gel polymer electrolytes and competitive quasi-solid-state Li metal batteries.

Four-State Electrochromism in Tris(4-aminophenyl)amine-terephthalaldehyde-based Covalent Organic Framework.

Covalent organic frameworks (COFs) are of massive interest due to their potential application spanning diverse fields such as gas storage and separation, catalysis, drug delivery systems, sensing, and organic electronics. In view of their application-oriented quest, the field of electrochromism marked a significant stride with the reporting of the first electrochromic COF in 2019 [J. Am. Chem. Soc. 2019, 141, 19831-19838]. Since then, new and novel COF structures with electrochromic features (denoted as ecCOFs) have been searched continuously. Yet, only a handful of ecCOFs have been constructed to date. A closer look at these reports suggests that multielectrochromism (showing at least three redox color states) in a COF assembly has only been achieved once, manifested through three-state electrochromism [Angew. Chem. 2021, 133, 12606 - 1261]. Herein, we report four-state electrochromism in tris(4-aminophenyl)amine-terephthalaldehyde (TAPA-PDA)-based COF constructed through the metal-catalyst free Schiff base approach. The four-state (orange, pear, green, and cyan) electrochromism demonstrated by the TAPA-PDA ecCOF opens several futuristic avenues for ecCOF's end use in flip-flop logic gates, intelligent windows, decorative displays, and energy-saving devices.

Ether-Based Gel Polymer Electrolyte for High-Voltage Potassium Ion Batteries.

Low-concentration ether electrolytes cannot efficiently achieve oxidation resistance and excellent interface behavior, resulting in severe electrolyte decomposition at a high voltage and ineffective electrode-electrolyte interphase. Herein, we utilize sandwich structure-like gel polymer electrolyte (GPE) to enhance the high voltage stability of potassium-ion batteries (PIBs). The GPE contact layer facilitates stable electrode-electrolyte interphase formation, and the GPE transport layer maintains good ionic transport, which enabled GPE to exhibit a wide electrochemical window and excellent electrochemical performance. In addition, Al corrosion under a high voltage is suppressed through the restriction of solvent molecules. Consequently, when using the designed GPE (based on 1 m), the K||graphite cell exhibits excellent cycling stability of 450 cycles with a capacity retention of 91%, and the K||FeFe-Prussian blue cell (2-4.2 V) delivers a high average Coulombic efficiency of 99.9% over 2200 cycles at 100 mA g-1. This study provides a promising path in the application of ether-based electrolytes in high-voltage and long-lasting PIBs.

Long-Cycling Cellulose-Based Gel Polymer Electrolyte Utilizing Nanohydrotalcite as a Li+ Transport Redistributor.

The hydroxyl groups on the surface of the cellulose-based gel polymer electrolyte lead to poor interfacial compatibility due to side reactions with lithium sheets. In this paper, a novel cellulose-based gel polymer electrolyte was prepared by uniformly coating the surface of a cellulose membrane with a nanohydrotalcite/PVDF-HFP composite using electrospinning technology. This cellulose-based gel polymer electrolyte exhibits good interfacial compatibility and excellent cycling stability (91.7% specific capacity retention after 500 cycles at 0.5C). Theory and experiments have shown that nanohydrotalcite on the surface of cellulose membrane can effectively prevent the contact of hydroxyl groups with lithium sheets to reduce the side reactions. In addition, nanohydrotalcite can also act as a Li+ transport redistributor to facilitate the uniform deposition of Li+ and reduce the formation of lithium dendrites to extend the cycle life.

Poly(Vinyl Alcohol)/Poly(Acrylic Acid) Gel Polymer Electrolyte Modified with Multi-Walled Carbon Nanotubes and SiO2 Nanospheres to Increase Rechargeability of Zn-Air Batteries.

Zn-air batteries (ZABs) are a promising technology; however, their commercialization is limited by challenges, including those occurring in the electrolyte, and thus, gel polymer electrolytes (GPEs) and hydrogels have emerged as substitutes for traditional aqueous electrolytes. In this work, PVA/PAA membranes were synthesized by the solvent casting method and soaked in 6 M KOH to act as GPEs. The thickness of the membrane was modified (50, 100, and 150 µm), and after determining the best thickness, the membrane was modified with synthesized SiO2 nanospheres and multi-walled carbon nanotubes (CNTs). SEM micrographs revealed that the CNTs displayed lengths of tens of micrometers, having a narrow diameter (95 ± 7 nm). In addition, SEM revealed that the SiO2 nanospheres had homogeneous shapes with sizes of 110 ± 10 nm. Physicochemical experiments revealed that SiO2 incorporation at 5 wt.% increased the water uptake of the PVA/PAA membrane from 465% to 525% and the ionic conductivity to 170 mS cm-1. The further addition of 0.5 wt.% CNTs did not impact the water uptake but it promoted a porous structure, increasing the power density and the stability, showing three-times-higher rechargeability than the ZAB operated with the PVA/PAA GPE.

Photo-Crosslinked Polyurethane-Containing Gel Polymer Electrolytes via Free-Radical Polymerization Method.

Using a novel technique, crosslinked gel polymer electrolytes (GPEs) designed for lithium-ion battery applications have been created. To form the photo crosslink via free-radical polymerization, a mixture of polyurethane acrylate (PUA), polyurethane methacrylate (PUMA), vinyl phosphonic acid (VPA), and bis[2-(methacryloyloxy)ethyl] phosphate (BMEP) was exposed to ultraviolet (UV) radiation during the fabrication process. The unique crosslinked configuration of the membrane increased its stability and made it suitable for use with liquid electrolytes. The resulting GPE has a much higher ionic conductivity (1.83 × 10-3 S cm-1) than the commercially available Celgrad2500 separator. A crosslinked structure formed by the hydrophilic properties of the PUA-PUMA blend and the higher phosphate content from BMEP reduced the leakage of the electrolyte solution while at the same time providing a greater capacity for liquid retention, significantly improving the mechanical and thermal stability of the membrane. GPP2 shows electrochemical stability up to 3.78 V. The coin cell that was assembled with a LiFePO4 cathode had remarkable cycling characteristics and generated a high reversible capacity of 149 mA h g-1 at 0.1 C. It also managed to maintain a consistent Coulombic efficiency of almost 100%. Furthermore, 91.5% of the original discharge capacity was maintained. However, the improved ionic conductivity, superior electrochemical performance, and high safety of GPEs hold great promise for the development of flexible energy storage systems in the future.

In Situ Formed Gel Polymer Electrolytes Enable Stable Solid Electrolyte Interface for High-Performance Lithium Metal Batteries.

Carbonate-based electrolytes show distinct advantages in high-voltage cathodes but generate nonuniform and mechanically fragile solid-electrolyte interphase (SEI) in lithium (Li) metal batteries. Herein, we propose a LiF-rich SEI incorporating an in situ polymerized poly(hexamethylene diisocyanate)-based gel polymer electrolyte (GPE) to improve the homogeneity and mechanical stability of SEI. Fluoroethylene carbonate (FEC) as a fluorine-based additive for building LiF-rich SEI on Li metal electrodes. With this strategy, the assembled Li symmetric batteries cycled stably for 700 h, and the formation of byproducts on the Li electrode surface was significantly inhibited. The Li/LiFePO4 battery delivered significant capacity retention (91% retention after 800 cycles) at 1 C. With high-voltage LiNi0.8Co0.1Mn0.1O2 (NCM811) as cathode, the Li/GPE-FEC/NCM811 cell delivered a discharge capacity of 168.9 mAh g-1 with a capacity retention of 82% after 300 cycles at 0.5 C. From the above, the work could assist the rapid development of high-energy-density rechargeable Li metal batteries toward remarkable performance.

Quasi-Gel Polymer Electrolyte Interfaced with Electrodes through Solvent-Swollen Poly(ethylene oxide) for High-Performance Lithium/Lithium-Ion Batteries.

Solid polymer electrolytes (SPEs) are regarded as a superior alternative to traditional liquid electrolytes of lithium-ion batteries (LIBs) due to their improved safety features. The practical implementation of SPEs faces challenges, such as low ionic conductivity at room temperature (RT) and inadequate interfacial contact, leading to high interfacial resistance across the electrode and electrolyte interfaces. In this study, we addressed these issues by designing a quasi-gel polymer electrolyte (QGPE), a blend of poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP), poly(ethylene oxide) (PEO), and succinonitrile (SN), with the desired mechanical strength, ionic conductivity, and interfacial stability through a simple solution casting technique. The QGPE features a thin solvated PEO layer on its surface, which wets the electrode, reducing the interfacial resistance and ensuring a homogeneous Li-ion flux across the interface. The optimized QGPE exhibits a good lithium-ion conductivity of 1.14 × 10-3 S cm-1 with a superior lithium-ion transference number of 0.7 at 25 °C. The Li/QGPE/Li symmetric cell exhibits a highly reversible lithium plating/stripping process for over 1300 h with minimal voltage polarization of ∼20 mV. The Li/QGPE/LiFePO4 full cell demonstrates good rate capability and excellent long-term cycling performance at a 0.1 C rate at 25 °C, maintaining a specific discharge capacity of 148 mAh g-1 over 200 cycles. The effectiveness of QGPE for LIBs is proven using a graphite/QGPE/LiFePO4 4 × 4 cm pouch cell, showcasing outstanding flexibility and tolerance against intentional abuse.

Gel Polymer Electrolyte Enables Low-Temperature and High-Rate Lithium-Ion Batteries via Bionic Interface Design.

Traditional ethylene carbonate (EC)-based electrolytes constrain the applications of silicon carbon (Si-C) anodes under fast-charging and low-temperature conditions due to sluggish Li+ migration kinetics and unstable solid electrolyte interphase (SEI). Herein, inspired by the efficient water purification and soil stabilization of aquatic plants, a stable SEI with a 3D desolvation interface is designed with gel polymer electrolyte (GPE), accelerating Li+ desolvation and migration at the interface and within stable SEI. As demonstrated by theoretical simulations and experiment results, the resulting poly(1,3-dioxolane) (PDOL), prepared by in situ ring-opening polymerization of 1,3-dioxolane (DOL), creates a 3D desolvation area, improving the Li+ desolvation at the interface and yielding an amorphous GPE with a high Li+ ionic conductivity (5.73 mS cm-1). Furthermore, more anions participate in the solvated structure, forming an anion-derived stable SEI and improving Li+ transport through SEI. Consequently, the Si-C anode achieves excellent rate performance with GPE at room temperature (RT) and low temperature (-40 °C). The pouch full cell coupled with LiFePO4 cathode obtains 97.42 mAh g-1 after 500 cycles at 5 C/5 C. This innovatively designed 3D desolvation interface and SEI represent significant breakthroughs for developing fast-charging and low-temperature batteries.

Unveiling potential of cellulose gel electrolyte: Molecular engineering for enhanced electrostatic interactions with Mg adatoms in Mg-ion battery.

The Mg-ion battery faces significant limitations due to its liquid electrolyte, which suffers from inherent issues such as leakage and the growth of Mg dendrites. In contrast, gel polymer electrolytes (GPEs) offer heightened safety, a wide voltage window, and excellent flexibility, making them a promising alternative with outstanding electrochemical performance. In this study, a cyano-modified cellulose (CEC) GPE was engineered to aim at enhancing ion transportation and promoting uniform ion-flux through interactions between N and Mg2+ ions. The resulting CEC-based GPE demonstrated a high ionic conductivity of 1.73 mS cm-1 at room temperature. Furthermore, it exhibited remarkable Mg plating/stripping performance (coulombic efficiency ∼96.7 %) and compatibility with electrodes. Importantly, when employed in a Mo6S8//Mg battery configuration, the CEC GPE displayed exceptional cycle stability, with virtually no degradation observed even after 650 cycles at 1C, thereby significantly advancing Mg-ion battery technology due to its excellent electrochemical properties. This study provides valuable insights into the molecular engineering of cellulose-based GPEs.

Methacrylated Wood Flour-Reinforced Gelatin-Based Gel Polymer as Green Electrolytes for Li-O2 Batteries.

With its very high theoretical energy density, the Li-O2 battery could be considered a valid candidate for future advanced energy storage solutions. However, the challenges hindering the practical application of this technology are many, as for example electrolyte degradation under the action of superoxide radicals produced upon cycling. In that frame, a gel polymer electrolyte was developed starting from waste-derived components: gelatin from cold water fish skin, waste from the fishing industry, and wood flour waste from the wood industry. Both were methacrylated and then easily cross-linked through a one-pot ultraviolet (UV)-initiated free radical polymerization, directly in the presence of the liquid electrolyte (0.5 M LiTFSI in DMSO). The wood flour works as cross-linking points, reinforcing the mechanical properties of the obtained gel polymer electrolyte, but it also increases Li-ion transport properties with an ionic conductivity of 3.3 mS cm-1 and a transference number of 0.65 at room temperature. The Li-O2 cells assembled with this green gel polymer electrolyte were able to perform 180 cycles at 0.1 mA cm-2, at a fixed capacity of 0.2 mAh cm-2, under a constant O2 flow. Cathodes post-mortem analysis confirmed that this electrolyte was able to slow down solvent degradation, but it also revealed that the higher reversibility of the cells could be explained by the formation of Li2O2 in the amorphous phase for a higher number of cycles compared to a purely gelatin-based electrolyte.

Porous wood composite as a green approach for enhancing electrochemical performance of gel polymer electrolytes for supercapacitors.

Delignified wood (DW) is a kind of environment-friendly porous material, and its unique hierarchical porous structure and excellent wettability are conducive to the rapid transfer and storage of ions, which can be used as electrolyte matrix of supercapacitors. In order to solve the deficiency of mechanical properties of DW as electrolyte materials, a novel cross-linked polyurethane (CPU) with high water absorption is designed as a reinforced matrix to improve the mechanical properties of electrolytes while maintaining high ionic conductivity. First, DW is immersed in CPU precursor solution, and the DW/CPU composite (W-CPC) is obtained by thermal crosslinking. Finally, W-CPC is soaked in 1M LiClO4 aqueous electrolyte to obtain the composite gel polymer electrolyte (W-CPC-GPE). Benefiting from the good hydrophilicity of W-CPC, the anisotropic vertical channels inside the DW, and the synergism of hydrogen bond and covalent bond. The highest ionic conductivity and mechanical strength of W-CPC-GPE are 3.5×10-2 S cm-1 and 0.67 GPa, respectively. The W-CPC-5-G based supercapacitor exhibits a high specific capacitance of 146.52 F g-1 and favorable capacitance retention rate of 90.7% after 5000 cycles. The results show that compounding with DW is an efficient and green way to develop high-performance gel polymer electrolytes for supercapacitors.

Immobile polyanionic backbone enables a 900-µm-thick electrode for compact energy storage with unprecedented areal capacitance.

Thickening of electrodes is crucial for maximizing the proportion of active components and thus improving the energy density of practical energy storage cells. Nevertheless, trade-offs between electrode thickness and electrochemical performance persist because of the considerably increased ion transport resistance of thick electrodes. Herein, we propose accelerating ion transport through thick and dense electrodes by establishing an immobile polyanionic backbone within the electrode pores; and as a proof of concept, gel polyacrylic electrolytes as such a backbone are in situ synthesized for supercapacitors. During charge and discharge, protons rapidly hop among RCOO- sites for oriented transport, fundamentally reducing the effects of electrode tortuosity and polarization resulting from concentration gradients. Consequently, nearly constant ion transport resistance per unit thickness is achieved, even in the case of a 900-µm-thick dense electrode, leading to unprecedented areal capacitances of 14.85 F cm-2 at 1 mA cm-2 and 4.26 F cm-2 at 100 mA cm-2. This study provides an efficient method for accelerating ion transport through thick and dense electrodes, indicating a significant solution for achieving high energy density in energy storage devices, including but not limited to supercapacitors.

Favored Amorphous LixSi Process with Restrained Volume Change Enabling Long Cycling Quasi-Solid-State SiOx anode.

Silicon-based anodes are becoming promising materials due to their high specific capacity. However, the intrinsically large volume change brought about by the alloying reaction results in the crushing of the active particles and destruction of the electrode structure, which severely limits its practical application. Various structured and modified silica-based anodes exhibit improved cycling stability and the demonstrated ability to mitigate their volume changes through interfacial and binder strategies. However, the issue of large volume changes in silicon-based anodes remains. Herein, we report a gel polymer electrolyte (GPE) prepared through an in situ thermal polymerization process that is suitable for SiOx anode materials and achieving long-term cycling stability. GPE-based cells essentially mitigate the volume change of SiOx anodes by guiding the unique lithiation/delithiation mechanism that tends to favor the formation and delithiation of amorphous-LixSi (a-LixSi) with smaller volume change, thereby mitigating electrode damage and cracking, and achieving the significant improvement in cycling performance. The prepared GPE-SiOx cells retained 693.80 mAh g-1 reversible capacity after 450 cycles at 500 mA g-1. In addition, the prelithiation process was incorporated to mitigate capacity fluctuations and improve the Initial Coulombic Efficiency (ICE), and a reversible capacity of 641.90 mAh g-1 was retained after 480 cycles.

Highly tough slide-crosslinked gel polymer electrolyte for stable lithium metal batteries.

Gel polymer electrolytes (GPEs) hold great promise for the practical application of lithium metal batteries. However, conventional GPEs hardly resists lithium dendrites growth and maintains long-term cycling stability of the battery due to its poor mechanical performance. Inspired by the slide-ring structure of polyrotaxanes (PRs), herein we developed a dynamic slide-crosslinked gel polymer electrolyte (SCGPE) with extraordinary stretchability of 970.93% and mechanical strength of 1.15 MPa, which is helpful to buffer the volume change of electrodes and maintain mechanical integrity of the battery structure during cycling. Notably, the PRs structures can provide fast ion transport channels to obtain high ionic conductivity of 1.73×10-3 S cm-1 at 30°C. Additionally, the strong polar groups in SCGPE restrict the free movement of anions to achieve high lithium-ion transference number of 0.71, which is favorable to enhance Li+ transport dynamics and induce uniform Li+ deposition. Benefiting from these features, the constructed Li|SCGPE-3|LFP cells exhibit ultra-long and stable cycle life over 1000 cycles and high-capacity retention (89.6% after 1000 cycles). Even at a high rate of 16C, the cells deliver a high capacity of 79.2 mAh g-1. The slide-crosslinking strategy in this work provides a new perspective on the design of advanced GPEs for LMBs.

Diagnostic Protocols for Evaluating the Degradation Mechanisms in Gel-Polymer Lithium Batteries.

Gel polymer electrolytes (GPEs) present a promising alternative to standard liquid electrolytes (LE) for Lithium-ion Batteries (LIBs) and Lithium Metal Batteries bridging the advantages of both liquid and solid polymer electrolytes. However, their cycle life still lags behind that of standard LIBs, and their degradation mechanisms remain poorly understood. A significant challenge is the need for specific diagnostic protocols to systematically study the degradation mechanisms of GPE-based cells. Challenges include the separation of cell components and effective washing, as well as the study of the solid electrolyte interfaces, all complicated by the semi-solid nature of GPEs. This paper provides a brief review of existing literature and proposes a comprehensive set of diagnostic tools for dismantling and evaluating the degradation of GPE-based LIBs. Finally, these methods and recommendations are applied to LiNi0.5Mn1.5O4 (LNMO)-graphite cells, revealing electrolyte oxidation as a major source of cell degradation.

In Situ-Initiated Poly-1,3-dioxolane Gel Electrolyte for High-Voltage Lithium Metal Batteries.

To realize high-energy-density Li metal batteries at low temperatures, a new electrolyte is needed to solve the high-voltage compatibility and fast lithium-ion de-solvation process. A gel polymer electrolyte with a small-molecular-weight polymer is widely investigated by combining the merits of a solid polymer electrolyte (SPE) and liquid electrolyte (LE). Herein, we present a new gel polymer electrolyte (P-DOL) by the lithium difluoro(oxalate)borate (LiDFOB)-initiated polymerization process using 1,3-dioxolane (DOL) as a monomer solvent. The P-DOL presents excellent ionic conductivity (1.12 × 10-4 S cm-1) at -20 °C, with an oxidation potential of 4.8 V. The Li‖LiCoO2 cell stably cycled at 4.3 V under room temperature, with a discharge capacity of 130 mAh g-1 at 0.5 C and a capacity retention rate of 86.4% after 50 cycles. Moreover, a high-Ni-content LiNi0.8Co0.1Mn0.1O2 (NCM811) cell can steadily run for 120 cycles at -20 °C, with a capacity retention of 88.4%. The underlying mechanism of high-voltage compatibility originates from the dense and robust B- and F-rich cathode interface layer (CEI) formed at the cathode interface. Our report will shed light on the real application of Li metal batteries under all-climate conditions in the future.

Preparation and Evaluation of PVDF-HFP-Based Gel Electrolyte for Ge-Sensitized Thermal Cell.

The semiconductor-sensitized thermal cell (STC) is a new thermoelectric conversion technology. The development of nonliquid electrolytes is the top priority for the practical application of the STC. In this study, a novel gel polymer electrolyte (PH-based GPE) composed of poly(vinylidenefluoride-co-hexafluoropropylene) (PH), 1-Methyl-2-pyrrolidone (NMP), and Cu ions was synthesized and applied to the STC system. The PH-based GPE synthesized at 45 °C showed higher open-circuit voltage (-0.3 V), short-circuit current density (59 µA cm-2) and diffusion coefficient (7.82 × 10-12 m2 s-1), indicating that a well-balanced structure among the NMP molecules was formed to generate a high-efficiency conduction path of the Cu ions. Moreover, the ion diffusion lengths decreased with decreasing content rates of NMP for the PH-based GPEs, indicating that the NMP plays an important role in the diffusion of Cu ions. Furthermore, the activation energy was calculated to be 107 kJ mol-1, and that was smaller compared to 150 kJ mol-1 for the poly(ethylene glycol)-based liquid electrolyte. These results play an important reference role in the development of electrolytes for STC systems. At the same time, they also provide a new avenue and reference indicator for the synthesis of high-performance and safe GPEs.

In Situ Polymerization Bi-Functional Gel Polymer Electrolyte for High Performance Quasi-Solid-State Lithium-Sulfur Batteries.

Lithium-sulfur (Li-S) batteries are expected to be the next-generation energy storage system due to the ultrahigh theoretical energy density and low cost. However, the notorious shuttle effect of higher-order polysulfides and the uncontrollable lithium dendrite growth are the two biggest challenges for commercially viable Li-S batteries. Herein, these two main challenges are solved by in situ polymerization of bi-functional gel polymer electrolyte (GPE). The initiator (SiCl4) not only drives the polymerization of 1,3-dioxolane (DOL) but also induces the construction of a hybrid solid electrolyte interphase (SEI) with inorganic-rich compositions on the Li anode. In addition, diatomaceous earth (DE) is added and anchored in the GPE to obtain PDOL-SiCl4-DE electrolyte through in situ polymerization. Combined with density functional theory (DFT) calculations, the hybrid SEI provides abundant adsorption sites for the deposition of Li+, inhibiting the growth of lithium dendrites. Meanwhile, the shuttle effect is greatly alleviated due to the strong adsorption capacity of DE toward lithium polysulfides. Therefore, the Li/Li symmetric cell and Li-S full cell assembled with PDOL-SiCl4-DE exhibit excellent cycling stability. This study offers a valuable reference for the development of high performance and safe Li-S batteries.