Environmental evaluation of flocculation efficiency in the separation of the microalgal biomass of Scenedesmus sp. cultivated in full-scale photobioreactors.

In this paper the environmental evaluation of the separation process of the microalgal biomass Scenedesmus sp. from full-scale photobioreactors was carried out at the Research and Development Nucleus for Sustainable Energy (NPDEAS), with different flocculants (iron sulfate - FeCl3, sodium hydroxide - NaOH, calcium hydroxide - Ca(OH)2 and aluminum sulphate Al2(SO4)3, by means of the life cycle assessment (LCA) methodology, using the SimaPro 7.3 software. Furthermore, the flocculation efficiency by means of optical density (OD) was also evaluated. The results indicated that FeCl3 and Al2(SO4)3 were highly effective for the recovery of microalgal biomass, greater than 95%. Though, when FeCl3 was used, there was an immediate change in color to the biomass after the orange colored salt was added, typical with the presence of iron, which may compromise the biomass use according to its purpose and Al2(SO4)3 is associated with the occurrence of Alzheimer's disease, restricting the application of biomass recovered through this process for nutritional purposes, for example. Therefore, it was observed that sodium hydroxide is an efficient flocculant, promoting recovery around 93.5% for the ideal concentration of 144 mg per liter. It had the best environmental profile among the compared flocculant agents, since it did not cause visible changes in the biomass or compromise its use and had less impact in relation to acidification, eutrophication, global warming and human toxicity, among others. Thus, the results indicate that it is important to consider both flocculation efficiency aspects and environmental impacts to identify the best flocculants on an industrial scale, to optimize the process, with lower amount of flocculant and obtain the maximum biomass recovery and decrease the impact on the extraction, production, treatment and reuse of these chemical compounds to the environment. However, more studies are needed in order to evaluate energy efficiency of the process coupled with other microalgal biomass recovery technologies. In addition, studies with natural flocculants, other polymers and changes in pH are also needed, as these are produced in a more sustainable way than synthetic organic polymers and have the potential to generate a biomass free of undesirable contaminants.

Coagulant Activity of Water-Soluble Moringa oleifera Lectin Is Linked to Lowering of Electrical Resistance and Inhibited by Monosaccharides and Magnesium Ions.

Moringa oleifera seeds contain a water-soluble lectin [water-soluble M. oleifera lectin (WSMoL)] that has shown coagulant activity. Magnesium ions are able to interfere with the ability of this lectin to bind carbohydrates. In this study, we performed structural characterization of WSMoL and analyzed its effect on the electrical resistance of a kaolin clay suspension in both presence and absence of monosaccharides (N-acetylglucosamine, glucose, or fructose) and magnesium ions. The coagulant activity of WSMoL was monitored by measuring optical density and electrical resistance over a period of 60 min. Native WSMoL had a molecular mass of 60 kDa and exhibited anionic nature (pI 5.5). In sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE), it appeared as three polypeptide bands of 30, 20, and 10 kDa. WSMoL reduced the optical density and electrical resistance of the kaolin suspension, which suggests that suspended particles are destabilized and that this is followed by formation of complexes. The coagulant activity of lectin decreased in the presence of Mg2+ ions and carbohydrates at concentrations that also inhibited hemagglutinating activity. This was most likely due to conformational changes in lectin structure. Our findings suggest that the coagulant activity of WSMoL is enhanced by lowering of electrical resistance of the medium and is impaired by lectin-carbohydrate and lectin-Mg2+ interactions.

Cytotoxicity of corrosion products of degradable Fe-based stents: relevance of pH and insoluble products.

Fe-based biodegradable metallic materials (Fe-BMMs) have been proposed for cardiovascular applications and are expected to disappear via corrosion after an appropriate period. However, in vivo studies showed that Fe ions release leads to accumulation of orange and brownish insoluble products at the biomaterial/cell interface. As an additional consequence, sharp changes in pH may affect the biocompatibility of these materials. In the present work, the experimental protocols were designed with the aim of evaluating the relative importance that these factors have on biocompatibility evaluation of BMMs. Mitochondrial activity (MTT assay) and thiobarbituric acid reactive substances (TBARS) assay on mammalian cells, exposed to 1-5 mM of added Fe3+ salt, were assessed and compared with results linked exclusively to pH effects. Soluble Fe concentration in culture medium and intracellular Fe content were also determined. The results showed that: (i) mitochondrial activity was affected by pH changes over the entire range of concentrations of added Fe3+ assayed, (ii) at the highest added Fe3+ concentrations (≥3 mM), precipitation was detected and the cells were able to incorporate the precipitate, that seems to be linked to cell damage, (iii) the extent of precipitation depends on the Fe/protein concentration ratio; and (iv) lipid peroxidation products were detected over the entire range of concentrations of added Fe3+. Hence, a new approach opens in the biocompatibility evaluation of Fe-based BMMs, since the cytotoxicity would not be solely a function of released (and soluble) ions but of the insoluble degradation product amount and the pH falling at the biomaterial/cell interface. The concentration of Fe-containing products at the interface depends on diffusional conditions in a very complex way that should be carefully analyzed in the future.