Ultrasound-assisted matrix solid-phase extraction based on deep eutectic solvents and zinc oxide: Extraction and determination of six active ingredients in Ligustri Lucidi Fructus.

In this study, we propose a novel strategy utilizing deep eutectic solvents (DESs) as both the extraction solvent and dispersing liquid, with nanometer zinc oxide (ZnO) serving as the adsorbent. This method incorporates ultrasound-assisted matrix solid phase dispersion (UA-MSPD) for the extraction of six active components (salidroside, echinacoside, acteoside, specnuezhenide, nuezhenoside G13, and oleanolic acid) from Ligustri Lucidi Fructus samples. The extracts were then analyzed using high-performance liquid chromatography equipped with a diode array detector. The effects of various parameters such as dispersant dosage, DESs volume, grinding time, ultrasonication duration, and eluent volume on extraction recovery were investigated and optimized using a central composite design under response surface methodology. The optimized conditions yielded detection limits ranging from 0.003 to 0.01 mg/g and relative standard deviations of 8.7% or lower. Extraction recoveries varied between 93% and 98%. The method demonstrated excellent linearity for the analytes (R2 ≥ 0.9997). The simple, green, and efficient DESs/ZnO-UA-MSPD technique proved to be rapid, accurate, and reliable for extracting and analyzing the six active ingredients in Ligustri Lucidi Fructus samples.

Photomutagenicity of N-nitrosoproline dissolved in non-aqueous solvent, oleic acid.

In the present study, we investigated the genotoxicity of the active products formed from N-nitrosoproline (NPRO) dissolved in oleic acid following ultraviolet A (UVA) irradiation, bypassing the need for metabolic activation. We previously demonstrated the photomutagenicity of NPRO dissolved in a phosphate-buffered solution. It has been suggested that the association of the nitrosamine group with acid ions facilitates rapid photodissociation and photoactivation. We hypothesized that NPRO's inherent carboxyl group may mimic an acid, inducing photodissociation and photomutagenicity, even in a non-aqueous solvent lacking acidic ions. Following UVA irradiation, NPRO dissolved in oleic acid exhibited a dose-dependent mutagenic activity. Similar results were obtained when NPRO was dissolved in linoleic acid and triolein. Nitric oxide formation, which is dependent on NPRO concentration, is accompanied by mutagenic activity. The mutagenicity spectrum obtained in response to NPRO irradiation followed the absorption curve of NPRO dissolved in oleic acid. Irradiated NPRO in oleic acid displayed relative stability, retaining approximately 18, 36, and 63 % of initial mutagenicity after 10 days of storage at 25, 4, and -20 °C, respectively. Thus NPRO stored in a fatty environment undergoes photoactivation upon irradiation, leading to genotoxicity.

Solvent induced amyloid polymorphism and the uncovering of the elusive class 3 amyloid topology.

Aggregation-prone-motifs (APRs) of proteins are short segments, which - as isolated peptides - form diverse amyloid-like crystals. We introduce two APRs - designed variants of the incretin mimetic Exendin-4 - that both display crystal-phase polymorphism. Crystallographic and spectroscopic analysis revealed that a single amino-acid substitution can greatly reduce topological variability: while LYIQWL can form both parallel and anti-parallel ß-sheets, LYIQNL selects only the former. We also found that the parallel/anti-parallel switch of LYIQWL can be induced by simply changing the crystallization temperature. One crystal form of LYIQNL was found to belong to the class 3 topology, an arrangement previously not encountered among proteinogenic systems. We also show that subtle environmental changes lead to crystalline assemblies with different topologies, but similar interfaces. Spectroscopic measurements showed that polymorphism is already apparent in the solution state. Our results suggest that the temperature-, sequence- and environmental sensitivity of physiological amyloids is reflected in assemblies of the APR segments, which, complete with the new class 3 crystal form, effectively sample all the originally proposed basic topologies of amyloid-like aggregates.

Enhancing Cellulose and Lignin Fractionation from Acacia Wood: Optimized Parameters Using a Deep Eutectic Solvent System and Solvent Recovery.

Cellulose and lignin, sourced from biomass, hold potential for innovative bioprocesses and biomaterials. However, traditional fractionation and purification methods often rely on harmful chemicals and high temperatures, making these processes both hazardous and costly. This study introduces a sustainable approach for fractionating acacia wood, focusing on both cellulose and lignin extraction using a deep eutectic solvent (DES) composed of choline chloride (ChCl) and levulinic acid (LA). A design of experiment was employed for the optimization of the most relevant fractionation parameters: time and temperature. In the case of the lignin, both parameters were found to be significant variables in the fractionation process (p-values of 0.0128 and 0.0319 for time and temperature, respectively), with a positive influence. Likewise, in the cellulose case, time and temperature also demonstrated a positive effect, with p-values of 0.0103 and 0.028, respectively. An optimization study was finally conducted to determine the maximum fractionation yield of lignin and cellulose. The optimized conditions were found to be 15% (w/v) of the wood sample in 1:3 ChCl:LA under a treatment temperature of 160 °C for 8 h. The developed method was validated through repeatability and intermediate precision studies, which yielded a coefficient of variation lower than 5%. The recovery and reuse of DES were successfully evaluated, revealing remarkable fractionation yields even after five cycles. This work demonstrates the feasibility of selectively extracting lignin and cellulose from woody biomass using a sustainable solvent, thus paving the way for valorization of invasive species biomass.

Optimization of Phenolic-Enriched Extracts from Olive Leaves via Ball Milling-Assisted Extraction Using Response Surface Methodology.

This study aims to extract phenolic-enriched compounds, specifically oleuropein, luteoloside, and hydroxytyrosol, from olive leaves using ball milling-assisted extraction (BMAE). Response surface methodology (RSM) and the Box-Behnken design (BBD) were used to evaluate the effects of the temperature, solvent-to-solid ratio, and milling speed on extraction recovery. The contents of the extract were determined by ultra-high-performance liquid chromatography-mass spectrometry (UPLC-MS) and converted to recoveries to evaluate the extraction efficiency. The optimal extraction conditions for oleuropein, luteoloside, and hydroxytyrosol were identified. Oleuropein had a recovery of 79.0% ± 0.9% at a temperature of 56.4 °C, a solvent-to-solid ratio of 39.1 mL/g, and a milling speed of 429 rpm. Luteoloside's recovery was 74.6% ± 1.2% at 58.4 °C, 31.3 mL/g, and 328 rpm. Hydroxytyrosol achieved 43.1% ± 1.3% recovery at 51.5 °C, 32.7 mL/g, and 317 rpm. The reason for the high recoveries might be that high energy ball milling could reduce the sample size further, breaking down the cell walls of olive leaves, to enhance the mass transfer of these components from the cell to solvent. BMAE is displayed to be an efficient approach to extracting oleuropein, luteoloside, and hydroxytyrosol from olive leaves, which is easy to extend to industrial production.

Green Approaches for the Extraction of Banana Peel Phenolics Using Deep Eutectic Solvents.

Banana peels, comprising about 35% of the fruit's weight, are often discarded, posing environmental and economic issues. This research focuses on recycling banana peel waste by optimizing advanced extraction techniques, specifically microwave-assisted (MAE) and ultrasound-assisted extraction (UAE), for the isolation of phenolic compounds. A choline chloride-based deep eutectic solvent (DES) with glycerol in a 1:3 ratio with a water content of 30% (w/w) was compared to 30% ethanol. Parameters, including sample-to-solvent ratio (SSR), extraction time, and temperature for MAE or amplitude for UAE, were varied. Extracts were analyzed for hydroxycinnamic acid (HCA) and flavonoid content, and antioxidant activity using FRAP and ABTS assays. DES outperformed ethanol, with HCA content ranging from 180.80 to 765.92 mg/100 g and flavonoid content from 96.70 to 531.08 mg/100 g, accompanied by higher antioxidant activity. Optimal MAE conditions with DES were an SSR of 1:50, a temperature of 60 °C, and a time of 10 min, whereas an SSR of 1:60, time of 5 min, and 75% amplitude were optimal for UAE. The polyphenolic profile of optimized extracts comprised 19 individual compounds belonging to the class of flavonols, flavan-3-ols, and phenolic acids. This study concluded that DESs, with their superior extraction efficiency and environmental benefits, are promising solvents for the extraction of high-value bioactive compounds from banana peels and offer significant potential for the food and pharmaceutical industries.

Influence of Solvent Polarity on the Conformer Ratio of Bicalutamide in Saturated Solutions: Insights from NOESY NMR Analysis and Quantum-Chemical Calculations.

The study presents a thorough and detailed analysis of bicalutamide's structural and conformational properties. Quantum chemical calculations were employed to explore the conformational properties of the molecule, identifying significant energy differences between conformers. Analysis revealed that hydrogen bonds stabilise the conformers, with notable variations in torsion angles. Conformers were classified into 'closed' and 'open' types based on the relative orientation of the cyclic fragments. NOE spectroscopy in different solvents (CDCl3 and DMSO-d6) was used to study the conformational preferences of the molecule. NOESY experiments provided the predominance of 'closed' conformers in non-polar solvents and a significant presence of 'open' conformers in polar solvents. The proportions of open conformers were 22.7 ± 3.7% in CDCl3 and 59.8 ± 6.2% in DMSO-d6, while closed conformers accounted for 77.3 ± 3.7% and 40.2 ± 6.2%, respectively. This comprehensive study underscores the solvent environment's impact on its structural behaviour. The findings significantly contribute to a deeper understanding of conformational dynamics, stimulating further exploration in drug development.

Green Extraction of Reed Lignin: The Effect of the Deep Eutectic Solvent Composition on the UV-Shielding and Antioxidant Properties of Lignin.

Lignin, the second most abundant natural polymer, is a by-product of the biorefinery and pulp and paper industries. This study was undertaken to evaluate the properties and estimate the prospects of using lignin as a by-product of the pretreatment of common reed straw (Phragmites australis) with deep eutectic solvents (DESs) of various compositions: choline chloride/oxalic acid (ChCl/OA), choline chloride/lactic acid (ChCl/LA), and choline chloride/monoethanol amine (ChCl/EA). The lignin samples, hereinafter referred to as Lig-OA, Lig-LA, and Lig-EA, were obtained as by-products after optimizing the conditions of reed straw pretreatment with DESs in order to improve the efficiency of subsequent enzymatic hydrolysis. The lignin was studied using gel penetration chromatography, UV-vis, ATR-FTIR, and 1H and 13C NMR spectroscopy; its antioxidant activity was assessed, and the UV-shielding properties of lignin/polyvinyl alcohol composite films were estimated. The DES composition had a significant impact on the structure and properties of the extracted lignin. The lignin's ability to scavenge ABTS+• and DPPH• radicals, as well as the efficiency of UV radiation shielding, decreased as follows: Lig-OA > Lig-LA > Lig-EA. The PVA/Lig-OA and PVA/Lig-LA films with a lignin content of 4% of the weight of PVA block UV radiation in the UVA range by 96% and 87%, respectively, and completely block UV radiation in the UVB range.

Prediction of Degradation Profiles for Various Sartans under Solvent-Free Mechanochemical Conditions.

For the approval of a drug, the stability data must be submitted to regulatory authorities. Such analyses are often time-consuming and cost-intensive. Forced degradation studies are mainly carried out under harsh conditions in the dissolved state, often leading to extraneous degradation profiles for a solid drug. Oxidative mechanochemical degradation offers the possibility of generating realistic degradation profiles. In this study, a sustainable mechanochemical procedure is presented for the degradation of five active pharmaceutical ingredients (APIs) from the sartan family: losartan potassium, irbesartan, valsartan, olmesartan medoxomil, and telmisartan. High-resolution mass spectrometry enabled the detection of impurities already present in untreated APIs and allowed the elucidation of degradation products. Significant degradation profiles could already be obtained after 15-60 min of ball milling time. Many of the identified degradation products are described in the literature and pharmacopoeias, emphasizing the significance of our results and the applicability of this approach to predict degradation profiles for drugs in the solid state.

Fabrication of 3D PCL/PVP scaffolds using monosodium glutamate as porogen by solvent casting/particulate leaching method for oral and maxillofacial bone tissue engineering.

The design of three-dimensional (3D) scaffolds should focus on creating highly porous, 3D structures with an interconnected pore network that supports cell growth. The scaffold's pore interconnectivity is directly linked to vascularization, cell seeding, guided cell migration, and transportation of nutrients and metabolic waste. In this study, different types of food flavors including monosodium glutamate, sugar, and sodium chloride were used as the porogens along with PCL/PVP blend polymer for solvent casting/particulate leaching method. The morphology, porosity, interconnectivity, chemical composition, water absorption, and mechanical properties of the fabricated scaffolds are carefully characterized. The scaffolds are biocompatible in bothin vitroandin vivoexperiments and do not trigger any inflammatory response while enhancing new bone formation and vascularization in rabbit calvaria critical-sized defects. The new bone merges and becomes denser along with the experiment timeline. The results indicate that the 3D PCL/PVP scaffolds, using monosodium glutamate as porogen, exhibited suitable biological performance and held promise for bone tissue engineering in oral and maxillofacial surgery.

Non-Invasive, Continuous, Quantitative Detection of Solvent Content in Vacuum Tray Drying.

A non-invasive capacitance instrument was embedded in the base of a vacuum-drying tray to monitor continuously the residual amount of solvent left in a pharmaceutical powder. Proof of concept was validated with Microcrystalline Cellulose laced with water, as well as water/acetone mixtures absorbed in a spray-dried Copovidone powder. To illustrate the role of impermeability of the base, we derive a model of vapor sorption that reveals the existence of a kinetic limit when solids are thinly spread, and a diffusion limit with greatly diminished effective diffusivity at large powder thickness. By monitoring the residual solvent content of powders, this new in situ technique offers advantages over indirect methods like mass spectrometry of vapor effluents, but without complications associated with probe fouling. To prescribe design guidelines and interpret signals, we model the electric field shed by the probe when a powder holds variable solvent mass fraction in the vertical direction.

A multi-stimuli-responsive fluorescence material based on 1,8-naphthalimide.

A pair of 1,8-naphthalimides (NPIs) were designed and successfully synthesized through embellishing amino-containing NPI with 4-diethylaminosalicyladehyde and 4-diethylaminobenzaldehyde, respectively. Their structures were fully confirmed by 1H/13C NMR, HR-MS and FT-IR spectroscopic studies. Their photophysical properties were systematically investigated in different solvents of varied polarity, in THF/water mixtures with varying water fractions (fw), and in THF solvent with varying concentrations of NPIs. It inferred that the distinct differences in emission between two NPIs during self-assembled process could be ascribed that the hydroxyl-containing NPI allowed the excited-state intramolecular proton transfer process between -OH and CH=N units in the aggregation state. Interestingly, the solid of 4-diethylaminosalicyladehyde-functionalized NPI exhibited multi-stimuli-responsive fluorescence changes involving mechanofluorochromism and HCl/NH3 vapor stimulus-induced conversion. However, no remarkable change was observed in the photoluminescence (PL) spectra for the solid of 4-diethylaminobenzaldehyde-functionalized NPI under the stimuli of mechanical force and organic solvent.

Eco-friendly solvent-based liquid-liquid extraction of phenolic acids from winery wastewater streams.

This study proposes liquid-liquid extraction (LLE) for the recovery of phenolic acids from winery wastewater replacing common volatile organic compounds (VOCs) with environmentally friendly solvents. On one hand, terpenes (α-pinene and p-cymene) and terpenoids (eucalyptol and linalool) were selected as green solvents and compared to common VOCs (ethyl acetate or 1-butanol). On the other hand, gallic acid (GA), vanillic acid (VA), syringic acid (SA) and caffeic acid (CA) were selected as phenolic acids to be recovered. The extraction performance was evaluated under different operation conditions: solvent-to-feed ratio, initial concentration of phenolic acids and temperature. This work also evaluated the back-extraction whole process global recovery and solvent regeneration, by means of aqueous NaOH solution. Eucalyptol has shown the highest overall global extraction performance (21.07 % for GA, 93.21 % for VA, 78.79 % for SA, and 80.57 % for CA) and lower water solubility compared to the best performing VOC solvent (1-butanol). Therefore, eucalyptol can be a potential eco-friendly solvent to replace VOCs for sustainable phenolic acid recovery from winery wastewater. Finally, to ensure a clean water stream after the LLE, the traces of solvent were completely removed by electrooxidation with boron-doped diamond anode at a current density of 422.54 A/m2.

Dependency of fentanyl analogue protomer ratios on solvent conditions as measured by ion mobility-mass spectrometry.

Recently, our group has shown that fentanyl and many of its analogues form prototropic isomers ("protomers") during electrospray ionization. These different protomers can be resolved using ion mobility spectrometry and annotated using mobility-aligned tandem mass spectrometry fragmentation. However, their formation and the extent to which experimental variables contribute to their relative ratio remain poorly understood. In the present study, we systematically investigated the effects of mixtures of common chromatographic solvents (water, methanol, and acetonitrile) and pH on the ratio of previously observed protomers for 23 fentanyl analogues. Interestingly, these ratios (N-piperidine protonation vs. secondary amine/O = protonation) decreased significantly for many analogues (e.g., despropionyl ortho-, meta-, and para-methyl fentanyl), increased significantly for others (e.g., cis-isofentanyl), and remained relatively constant for the others as solvent conditions changed from 100% organic solvent (methanol or acetonitrile) to 100% water. Interestingly, pH also had significant effects on this ratio, causing the change in ratio to switch in many cases. Lastly, increasing conditions to pH ≥ 4.0 also prompted the appearance of new mobility peaks for ortho- and para-methyl acetyl fentanyl, where all previous studies had only showed one single distribution. Because these ratios have promise to be used qualitatively for identification of these (and emerging) fentanyl analogues, understanding how various conditions (i.e., mobile phase selection and/or chromatographic gradient) affect their ratios is critically important to the development of advanced ion mobility and mass spectrometry methodologies to identify fentanyl analogues.

Dataset for quantum-mechanical exploration of conformers and solvent effects in large drug-like molecules.

We here introduce the Aquamarine (AQM) dataset, an extensive quantum-mechanical (QM) dataset that contains the structural and electronic information of 59,783 low-and high-energy conformers of 1,653 molecules with a total number of atoms ranging from 2 to 92 (mean: 50.9), and containing up to 54 (mean: 28.2) non-hydrogen atoms. To gain insights into the solvent effects as well as collective dispersion interactions for drug-like molecules, we have performed QM calculations supplemented with a treatment of many-body dispersion (MBD) interactions of structures and properties in the gas phase and implicit water. Thus, AQM contains over 40 global and local physicochemical properties (including ground-state and response properties) per conformer computed at the tightly converged PBE0+MBD level of theory for gas-phase molecules, whereas PBE0+MBD with the modified Poisson-Boltzmann (MPB) model of water was used for solvated molecules. By addressing both molecule-solvent and dispersion interactions, AQM dataset can serve as a challenging benchmark for state-of-the-art machine learning methods for property modeling and de novo generation of large (solvated) molecules with pharmaceutical and biological relevance.

Preparation of Microsponge Drug Delivery System (MSDDS) Followed by a Scale-Up Approach.

In 1987, Won invented the solid-phase porous microsphere (MS), which stores bioactive compounds in many interconnected voids. Spherical particles (5-300 µm), MS, may form clusters of smaller spheres, resulting in many benefits. The current investigation focussed on gel-encased formulation, which can be suitable for dermal usage. First, quasi-emulsion (w/o/w) solvent evaporation was used to prepare 5-fluorouracil (5 FU) MS particles. The final product was characterized (SEM shows porous structure, FTIR and DSC showed drug compatibility with excipients, and gel formulation is shear-thinning) and further scaled up using the 8-fold method. Furthermore, CCD (Central Composite Design) was implemented to obtain the optimized results. After optimizing the conditions, including the polymer (600 mg, ethyl cellulose (EC), eudragit RS 100 (ERS)), stirring speed (1197 rpm), and surfactant concentration (2% w/v), we achieved the following results: optimal yield (63%), mean particle size (152 µm), drug entrapment efficiency (76%), and cumulative drug release (74.24% within 8 h). These findings are promising for industrial applications and align with the objectives outlined in UN Sustainable Development Goals 3, 9, and 17, as well as the goals of the G20 initiative.

Evaluation of wound healing and anti-inflammatory activity of hydro-alcoholic extract and solvent fractions of the leaves of Clerodendrum myricoides (Lamiaceae) in mice.

BACKGROUND: Wounds significantly affect people's quality of life and the clinical and financial burden of healthcare systems around the world. Many of the current drugs used to treat wounds have problems such as; allergies and drug resistance. Hence, the exploration of new therapeutic agents from natural origin may avert this problem. Clerodendrum myricoides have long been used to treat wounds in Ethiopia. Despite this, nothing has so far been reported about the wound healing and anti-inflammatory activity of C. myricoides. This study aimed to evaluate the wound healing and anti-inflammatory activity of 80% methanol extract and solvent fractions of C. myricoides leaves in mice. METHODS: Leaves of C. myricoides were extracted using the maceration technique. The extract was formulated as 5% and 10% w/w ointments. The wound healing activity of the extract was evaluated using excision, incision, and burn wound models whereas the healing activities of solvent fractions were evaluated using the excision wound model. A carrageenan-induced paw edema model was used for the anti-inflammatory test. RESULTS: In the dermal toxicity test, 2000 mg/kg of 10% extract was found to be safe. In excision and burn wound models, treatment with 10% and 5% extract showed a significant (p<0.001) wound contraction. Solvent fractions of the extract significantly reduced wound contraction. A significant reduction in periods of epithelialization and favorable histopathology changes were shown by extract ointments. In incision wounds, 10% (p<0.001) and 5% (p<0.01) extracts significantly increase skin-breaking strength. After one hour of treatment, 400 mg/kg (p<0.001) and 200 mg/kg (p<0.05) showed significant reduction in paw edema. CONCLUSION: Results of this study indicate that 80% methanol extract and the solvent fraction of the leaves of C. myricoides possess wound-healing and anti-inflammatory activity and support traditional claims.

HSPiP, Computational, and Thermodynamic Model-Based Optimized Solvents for Subcutaneous Delivery of Tolterodine Tartrate and GastroPlus­Based In Vivo Prediction in Humans: Part II.

In part I, we reported Hansen solubility parameters (HSP, HSPiP program), experimental solubility at varied temperatures for TOTA delivery. Here, we studied dose volume selection, stability, pH, osmolality, dispersion, clarity, and viscosity of the explored combinations (I-VI). Ex vivo permeation and deposition studies were performed to observe relative diffusion rate from the injected site in rat skin. Confocal laser scanning microscopy (CLSM) study was conducted to support ex vivo findings. Moreover, GastroPlus predicted in vivo parameters in humans and the impact of various critical factors on pharmacokinetic parameters (PK). Immediate release product (IR) contained 60% of PEG400 whereas controlled release formulation (CR) contained PEG400 (60%), water (10%) and d-limonene (30%) to deliver 2 mg of TOTA. GastroPlus predicted the plasma drug concentration of weakly basic TOTA as function of pH (from pH 2.0 to 9). The cumulative drug permeation and drug deposition were found to be in the order as B-VI˃ C-VI˃A-VI across rat skin. This finding was further supported with CLSM. Moreover, IR and CR were predicted to achieve Cmax of 0.0038 µg/ mL and 0.00023 µg/mL, respectively, after sub-Q delivery. Added limonene in CR extended the plasma drug concentration over period of 12 h as predicted in GastroPlus. Parameters sensitivity analysis (PSA) assessment predicted that sub-Q blood flow rate is the only factor affecting PK parameters in IR formulation whereas this was insignificant for CR. Thus, sub-Q delivery CR would be promising alternative with ease of delivery to children and aged patient.

Sustainable and Biomimetic Methodology for Extraction of High-Value-Added Compounds in Almond Hulls.

Almond trees are the most cultivated nut tree in the world. The production of almonds generates large amounts of by-products, much of which goes unused. Herein, this study aimed to develop a green chemistry approach to identify and extract potentially valuable compounds from almond by-products. Initially, a screening was performed with 10 different Natural Deep Eutectic Solvents (NADESs). The mixture lactic acid/glycerol, with a molar ratio 1:1 (1:50 plant material to NADES (w/v) with 20% v/v of water) was identified as the best extraction solvent for catechin, caffeoylquinic acid, and condensed tannins in almond hulls. Subsequently, a method was optimized by a Design of Experiment (DoE) protocol using a miniaturized extraction technique, Microwave-Assisted Extraction (MAE), in conjunction with the chosen NADESs. The optimal conditions were found to be 70 °C with 15 min irradiation time. The optimal extraction conditions determined by the DoE were confirmed experimentally and compared to methods already established in the literature. With these conditions, the extraction of metabolites was 2.4 times higher, according to the increase in total peak area, than the established literature methods used. Additionally, by applying the multiparameter Analytical Greenness Metric (AGREE) and Green Analytical Process Index (GAPI) metrics, it was possible to conclude that the developed method was greener than the established literature methods as it includes various principles of green analytical chemistry.

Optimizing the Extraction of the Polyphenolic Fraction from Defatted Strawberry Seeds for Tiliroside Isolation Using Accelerated Solvent Extraction Combined with a Box-Behnken Design.

Tiliroside is a natural polyphenolic compound with a wide range of biological activity, and defatted strawberry seeds are its rich source. The goal of this study was to optimize accelerated solvent extraction (ASE) conditions, including temperature, solvent composition, and the number of extraction cycles, using Box-Behnken design to maximize the yield of tiliroside. UPLC-DAD-MS was applied to investigate the polyphenolic composition of the extracts, and preparative liquid chromatography (pLC) was used for isolation. All obtained mathematical models generally showed an increase in the efficiency of isolating polyphenolic compounds with an increase in temperature, ethanol content, and the number of extraction cycles. The optimal established ASE conditions for tiliroside were as follows: a temperature of 65 °C, 63% ethanol in water, and four extraction cycles. This allowed for the obtainment of a tiliroside-rich fraction, and the recovery of isolated tiliroside from plant material reached 243.2 mg from 100 g. Our study showed that ASE ensures the isolation of a tiliroside-rich fraction with high effectiveness. Furthermore, defatted strawberry seeds proved to be a convenient source of tiliroside because the matrix of accompanying components is relatively poor, which facilitates separation.