ABSTRACT
Municipal wastewater treatment systems use the chemical oxygen demand test (COD) to identify organic contaminants in industrial effluents that impede treatment due to their high concentration. This study reduced the COD levels in tannery wastewater using a multistage treatment process that included Fenton oxidation, chemical coagulation, and nanotechnology based on a synthetic soluble COD standard solution. At an acidic pH of 5, Fenton oxidation reduces the COD concentration by approximately 79%. It achieves this by combining 10 mL/L of H2O2 and 0.1 g/L of FeCl2. Furthermore, the author selected the FeCl3 coagulant for the coagulation process based on the best results of comparisons between different coagulants. At pH 8.5, the coagulation dose of 0.15 g/L achieved the maximum COD removal efficiency of approximately 56.7%. Finally, nano bimetallic Fe/Cu was used to complete the degradation and adsorption of the remaining organic pollutants. The XRD, SEM, and EDX analyses proved the formation of Fe/Cu nanoparticles. A dose of 0.09 g/L Fe/Cu NPs, 30 min of contact time, and a stirring rate of 200 rpm achieve a maximum removal efficiency of about 93% of COD at pH 7.5. The kinetics studies were analyzed using pseudo-first-order P.F.O., pseudo-second-order P.S.O., and intraparticle diffusion models. The P.S.O. showed the best fit among the kinetic models, with an R2 of 0.998. Finally, the authors recommended that technique for highly contaminated industrial effluents treatment for agriculture or industrial purposes.
ABSTRACT
The mechanism of interaction between magnesite mineral and phosphoric acid (0.001-0.5 M) in addition to the determination of the protective properties for Ti alloy (working electrode) in phosphoric acid both with and without an inhibitor have been investigated by electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization measurements. Results of electrochemical tests show that the corrosion resistance of titanium alloy in phosphoric acid solution only increased and hydrogen production decreased by either decreasing acid concentration or increasing immersion time associated with the thickening of the oxide film formed on the alloy surface. On adding magnesite, the corrosion resistance of Ti alloy is enhanced by increasing the phosphoric acid concentration (0.001-0.5 M) due to the formation of sparingly soluble magnesium phosphate film on the alloy surface that inhibits the effect of increasing hydrogen evolution reaction due to the pH value decreases. The increasing adsorption behavior of the magnesite inhibitor and decreasing its diffusion were deduced from EIS measurements. Thus, the addition of 3% magnesite minimizes the corrosion by forming a new protective film (Mg3(PO4)2), which differs from the traditional passive film and prevents the effect of the increase of hydrogen evolution. The surface morphology and chemical composition of the tested alloy were determined using scanning electron microscopy (SEM), Fourier transform Infra-Red spectroscopy (FTIR), X-ray diffraction (XRD), X-ray Fluorescence (XRF) and In situ Raman spectroscopy.
ABSTRACT
A novel environmental nano-catalyst based on zeolite (ZE) adjusted with carbon nanotube/silver nanoparticles (Ag/CNT) ornamented carbon paste electrode (CPE) is used for electrochemical oxidation of propylene glycol (PG) in 0.5 M H2SO4 solution. The techniques like cyclic voltammetry (CV), chronoamperometry (CA) and electrochemical impedance spectroscopy (EIS) are utilized to achieve the catalytic activity performance. Surface characteristics are achieved by means of scanning electron microscope (SEM) and Energy dispersive X-ray analysis (EDX) techniques. Enhancing the loading magnitude of CNT into catalyst's ingredient can meaningfully develop the catalytic activity of the electrocatalyst towards propylene oxidation. The impact of altering the concentration of propylene glycol and the scanning rate on the resulting electrocatalyst performance during the oxidation cycle is considered. Chronoamperograms present an amplify of the steady state oxidation current density values after addition of these nano-catalysts. A promising catalytic stability of nano-catalyst has been achieved in electing its use for propylene glycol electro-oxidation in fuel cells applications.
