An Optical Device Based on a Chemical Chip and Surface Plasmon Platform for 2-Furaldehyde Detection in Insulating Oil.

2-Furaldehyde (2-FAL) is one of the main by-products of the degradation of hemicellulose, which is the solid material of the oil-paper insulating system of oil-filled transformers. For this reason, it has been suggested as a marker of the degradation of the insulating system; sensing devices for 2-FAL analysis in a wide concentration range are of high interest in these systems. An optical sensor system is proposed; this consists of a chemical chip, able to capture 2-FAL from the insulating oil, coupled with a surface plasmon resonance (SPR) probe, both realized on multimode plastic optical fibers (POFs). The SPR platform exploits gold nanofilm or, alternatively, a double layer of gold and silicon oxide to modulate the sensor sensitivity. The capturing chip is always based on the same molecularly imprinted polymer (MIP) as a receptor specific for 2-FAL. The system with the SPR probe based on a gold nanolayer had a higher sensitivity and a lower detection limit of fractions of µg L-1. Instead, the SPR probe, based on a double layer (gold and silicon oxide), has a lower sensitivity with a worse detection limit, and it is suitable for the detection of 2-FAL at concentrations of 0.01-1 mg L-1.

Splitter-Based Sensors Realized via POFs Coupled by a Micro-Trench Filled with a Molecularly Imprinted Polymer.

An optical-chemical sensor based on two modified plastic optical fibers (POFs) and a molecularly imprinted polymer (MIP) is realized and tested for the detection of 2-furaldehyde (2-FAL). The 2-FAL measurement is a scientific topic of great interest in different application fields, such as human health and life status monitoring in power transformers. The proposed sensor is realized by using two POFs as segmented waveguides (SW) coupled through a micro-trench milled between the fibers and then filled with a specific MIP for the 2-FAL detection. The experimental results show that the developed intensity-based sensor system is highly selective and sensitive to 2-FAL detection in aqueous solutions, with a limit of detection of about 0.04 mg L-1. The proposed sensing approach is simple and low-cost, and it shows performance comparable to that of plasmonic MIP-based sensors present in the literature for 2-FAL detection.

Exploring albumin-sulfonephthalein dyes interactions by a chemometric-assisted and multi-technique equilibria analysis in solution.

Albumin is undoubtedly the most studied protein thanks to its widespread diffusion and biochemistry; despite its binding ability towards different dyes, provoking dye's colour change, has been exploited for decades for quantification purposes, the joint effect of working pH, ionic strength, and dye's pKa still remains only sporadically discussed. In the present study, the interaction of Bovine Serum Albumin (BSA) with five dyes belonging to the sulfonephthalein group, Bromophenol Blue (BPB, pKa = 3.75), Bromocresol Green (BCG, pKa = 4.42), Chlorophenol Red (CPR, pKa = 5.74), Bromocresol Purple (BCP, pKa = 6.05) and Bromothymol Blue (BTB, pKa = 6.72), is investigated at four working pH values (3.5, 6.0, 7.5 and 9.0) and two ionic strength conditions by UV-Vis spectroscopy. Principal Component Analysis is then applied to rationalize dye behavior upon BSA addition at each pH value and to summarize the protein effect on dyes' spectral features, identifying three general behaviors. The most relevant systems are then submitted to further characterization involving a solution equilibria study aimed at determining conditional binding constants for the selected DSA-dye adducts and fluorescence, CD, and 1H NMR spectroscopy to evaluate the binding effect on the species involved.

A Screen-Printed Voltammetric Sensor Modified with Electropolymerized Molecularly Imprinted Polymer (eMIP) to Determine Gallic Acid in Non-Alcoholic and Alcoholic Beverages.

This paper presents a low-cost disposable sensor for gallic acid (GA) detection in non-alcoholic and alcoholic beverages using a screen-printed cell (SPC) whose working electrode (in graphite) is modified with electrosynthesized molecularly imprinted polypyrrole (eMIP). Our preliminary characterization of the electrochemical process shows that gallic acid (GA) undergoes irreversible oxidation at potentials of about +0.3 V. The peak potential is not affected by the presence of the eMIP film and alcohol percentages (ethanol) up to 20%. The GA determination is based on a differential pulse voltammetry (DPV) analysis leveraging its oxidation peak. The calibration data and the figures of merit of the analytical method (LOD, LOQ, and linear range) are calculated. To validate the feasibility of the sensor's application for the dosing of GA in real matrices, some non-alcoholic and alcoholic beverages are analyzed. The results are then compared with those reported in the literature and with the total polyphenol content determined by the Folin-Ciocalteu method. In all cases, the concentrations of GA align with those previously found in the literature for the beverages examined. Notably, the values are consistently lower than the total polyphenol content, demonstrating the sensor's selectivity in discriminating the target molecule from other polyphenols present.

Molecularly Imprinted Polymer-based voltammetric sensor for amino acids/indazole derivatives synthetic cannabinoids detection.

BACKGROUND: Synthetic cannabinoids (SCs) are a broad class of illicit drugs that are classified according to the chemical structure of the aromatic core that they present (i.e., indole, imidazole, pyrrole) and their detection is still a challenge, despite their widespread diffusion. The identification of a specific class of SC in complex matrices, such as real samples with a rapid, economic analytical device useable directly in the field, is highly desirable, as it can provide immediate and reliable information that eventually addresses more targeted analyses. RESULTS: The present paper proposes a Molecularly Imprinted Polymer (MIP)-based voltammetric sensor for the rapid and selective detection of indazole-type SCs. In this context, a polyacrylate-based MIP was used to functionalize a Pt electrode. The MIP composition was optimized through a Design of Experiments approach, and for the sake of safety, a non-psychotropic compound structurally related to the selected SCs was employed as the template in the MIP formulation. A complete characterization of the electrochemical behavior of the selected SCs was performed, and differential pulse voltammetry (DPV) in acetonitrile/lithium perchlorate 0.1 M was the technique applied for their quantification. LOD around 0.01 mM and linearity up to 0.8 mM were found. Comparison with the non-imprinted (NIP) modified and bare electrodes showed better selectivity and reproducibility of the MIP-based sensor. Recovery tests (in the 70-115 % range) were performed on simulated pills and smoking mixtures to test the reliability of the proposed method. SIGNIFICANCE: The method proposed allows the identification and quantification of indazole-based SCs as a class in complex matrices. Due to the selectivity of the obtained device, no clean-up of the sample before analyses is needed. For the same reason, the interference of cutting substances and natural cannabinoids was negligible.

Colorimetric Paper-Based Analytical Devices (PADs) Backed by Chemometrics for Pd(II) Detection.

This paper presents the development of cheap and selective Paper-based Analytical Devices (PADs) for selective Pd(II) determination from very acidic aqueous solutions. The PADs were obtained by impregnating two cm-side squares of filter paper with an azoic ligand, (2-(tetrazolylazo)-1,8 dihydroxy naphthalene-3,6,-disulphonic acid), termed TazoC. The so-obtained orange TazoC-PADs interact quickly with Pd(II) in aqueous solutions by forming a complex purple-blue-colored already at pH lower than 2. The dye complexes no other metal ions at such an acidic media, making TazoC-PADs highly selective to Pd(II) detection. Besides, at higher pH values, other cations, for example, Cu(II) and Ni(II), can interact with TazoC through the formation of stable and pink-magenta-colored complexes; however, it is possible to quantify Pd(II) in the presence of other cations using a multivariate approach. To this end, UV-vis spectra of the TazoC-PADs after equilibration with the metal ions solutions were registered in the 300-800 nm wavelength range. By applying Partial Least Square regression (PLS), the whole UV-vis spectra of the TazoC-PADs were related to the Pd(II) concentrations both when present alone in solution and also in the presence of Cu(II) and Ni(II). Tailored PLS models obtained with matrix-matched standard solutions correctly predicted Pd(II) concentrations in unknown samples and tap water spiked with the metal cation, making the method promising for quick and economical sensing of Pd(II).

Synthesis, Characterization and Application of a MIP-polyHIPE for Selective Extraction of Angiotensin II Receptor Antagonists Residues in Natural Waters.

Polymers via high internal phase emulsion (polyHIPEs) were molecularly imprinted with Irbesartan, an antihypertensive drug belonging to the class of angiotensin II receptor antagonists (sartan drugs), chosen for the proof-of-concept extraction of hazardous emerging contaminants from water. Different analyte-functional monomer molar ratios (1:100, 1:30 and 1:15) were investigated, and the MIP polyHIPEs have been characterized, parallel to the not imprinted polymer (NIP), by batch sorption experiments. The material with the highest template-functional monomer ratio was the best for Irbesartan removal, showing a sorption capacity fivefold higher than the NIP. Regarding the adsorption kinetics, the analyte-sorbent equilibrium was reached after about 3 h, and the film diffusion model best fitted the kinetic profile. Selectivity was further demonstrated by testing Losartan, another sartan drug, observing a fourfold lower sorption capacity, but still higher than that of NIP. The polymers were also synthesized in cartridges for solid-phase extraction (SPE), which was helpful for evaluating the breakthrough curves and performing pre-concentrations. These have been done in tap and river water samples (100-250 mL, 15-500 µg L-1 Irbesartan), obtaining quantitative sorption/desorption on the MIP-polyHIPE (RSD < 14%, n = 3). The NIP provided a recovery of just around 30%, evidence of partial uptake of the target from water.

Chemometric-Assisted Litmus Test: One Single Sensing Platform Adapted from 1-13 to Narrow pH Ranges.

A novel 3 × 4 colorimetric sensing platform, named the chemometric-assisted litmus test (CLT), has been developed by covalently anchoring commercial pH indicators to ethylene vinyl alcohol (EVOH). The proposed device can be exploited for pH determinations in a wide range from 1 to 13 and in specific narrow ranges, achieving sufficient accuracy and errors below 0.5 pH units. The experimental procedure is simple, quick and reliable; equilibration is reached in less than 2 h, CLT pictures are acquired by a camera, and data treatment is performed applying chemometric techniques such as principal component analysis (PCA) and partial least square regression (PLS) to RGB indices.

The colorful world of sulfonephthaleins: Current applications in analytical chemistry for "old but gold" molecules.

Sulfonephthaleins represent one of the most common and widely employed reactive dyes in analytical chemistry, thanks to their stability, low-cost, well-visible colors, reactivity and possibilities of chemical modification. Despite being first proposed in 1916, nowadays, these molecules play a fundamental role in biological and medical applications, environmental analyses, food quality monitoring and other fields, with a particular focus on low-cost and disposable devices or methods for practical applications. Since up to our knowledge, no reviews or book chapters focused explicitly on sulfonephthaleins have ever been published, in this review, we will briefly describe sulfonephthaleins history, their acid-base properties will be discussed, and the most recent applications in different fields will be presented, focusing on the last ten years literature (2014-2023). Finally, safety and environmental issues will be briefly discussed, despite being quite controversial.

Potentiometric MIP-Modified Screen-Printed Cell for Phenoxy Herbicides Detection.

In this study, a molecularly imprinted polymer (MIP)-based screen-printed cell is developed for detecting phenoxy herbicides using 2-methyl-4-chlorophenoxyacetic acid (MCPA) as the template. MCPA is a phenoxy herbicide widely used since 1945 to control broadleaf weeds via growth regulation, primarily in pasture and cereal crops. The potentiometric cell consists of a silver/silver chloride pseudo-reference electrode and a graphite working electrode coated with a MIP film. The polymeric layer is thermally formed after drop-coating of a pre-polymeric mixture composed of the reagents at the following molar ratio: 1 MCPA: 15 MAA (methacrylic acid): 7 EGDMA (ethylene glycol dimethacrylate). After template removal, the recognition cavities function as the ionophore of a classical ion selective electrode (ISE) membrane. The detected ion is the deprotonated MCPA specie, negatively charged, so the measurements were performed in phosphate buffer at pH 5.5. A linear decrease of the potential with MCPA concentration, ranging from 4 × 10-8 to 1 × 10-6 mol L-1, was obtained. The detection limit and the limit of quantification were, respectively, 10 nmol L-1 and 40 nmol L-1. A Nernstian slope of about -59 mV/dec was achieved. The method has precision and LOD required for MCPA determination in contaminated environmental samples.

Detection of 2-Furaldehyde in Milk by MIP-Based POF Chips Combined with an SPR-POF Sensor.

An innovative optical-chemical sensor has been used to detect the 2-furaldehyde (2-FAL) in milk. The proposed sensing approach exploits the refractive index changing in a microstructured chip based on a plastic optical fiber (POF) with orthogonal micro-holes containing a specific molecularly imprinted polymer (MIP). This POF-MIP chemical chip modifies the surface plasmon resonance (SPR) phenomena excited in another sensor chip realized in POFs (SPR-POF) and connected in series. The proposed sensor configuration exploits MIP receptors avoiding any modification of the gold film of the SPR platform. This work reports the performance, particularly the high sensitivity and low detection limit, in complex matrices such as buffalo milk fortified with 2-FAL and in different commercial kinds of cow milk thermally treated for pasteurization. The measurements were carried out in about ten minutes by dropping the solution under-test on the planar D-shaped POF surface of the chemical chip. In contrast, on the gold surface of the SPR-POF platform, a water drop is always placed to excite the SPR phenomenon, which is modulated by the chemical chip via MIP-2-FAL binding. Furthermore, the experimental results demonstrated the pros and cons of the proposed sensor system. Thanks to the high sensitivity of the sensor system, the detection of 2-FAL in the diluted milk sample (1:50) was achieved. The dilution is required to reduce the interferent effect of the complex matrix.

RGB-Detector: A Smart, Low-Cost Device for Reading RGB Indexes of Microfluidic Paper-Based Analytical Devices.

A user-friendly, low-cost detector able to read the RGB indexes of microfluidic paper-based analytical devices (µPADs) was developed. The RGB-detector was built with 3D printing using PLA+ and reused Li-ion batteries. It is Arduino-based, which provides an easy interface between the sensor TCS3200, which reads the quadratic wave of the times corresponding to the RGB numbers, the Arduino itself, whose software translates the times into RGB values, and the touchscreen display, NX3224T028, which shows the results. This detector permits multi-sample analysis since it has a sample holder that can keep up to six µPADs simultaneously and rotate after the display's request. This work shows how the readings of the RGB indexes by the proposed RGB-detector implement the measurements' reproducibility. As a proof-of-concept, the RGB-detector application to a green array of µPADs for pH measurement coupled with chemometric analysis allowed us to achieve good results in terms of precision and agreement with the pH values measured by a classical pH-meter.

Quick and Easy Covalent Grafting of Sulfonated Dyes to CMC: From Synthesis to Colorimetric Sensing Applications.

Carboxymethyl cellulose, the most promising cellulose-derivatives, pulls together low cost, abundancy, biocompatibility, unique properties and, unlike the precursor, chemical reactivity. This latter aspect arouses the curiosity of chemists around the possibility of chemical modification and the production of interesting functional materials. Here, a two-step reaction is proposed for the covalent anchoring of a wide variety of molecules containing sulfonic groups to CMC. The strength points of the proposed pathway have to be found in the quick and easy reactions and workup that allow to obtain ready-to-use functional materials with very high yields. Having in this case exploited a pH-sensitive dye as a sulfonated molecule, the functional material is an interesting candidate for the development of colorimetric miniaturized sensors via the following drop-casting deposition: once optimized sensors preparation by design of experiments, an example of application on real samples is reported.

An Optical Fiber Sensor for Uranium Detection in Water.

An optical sensor for uranyl has been prepared based on a gold-plated D-shaped plastic optical fiber (POF) combined with a receptor consisting of a bifunctional synthetic molecule, 11-mercaptoundecylphosphonic acid (MUPA), with a phosphonic group for complexing the considered ion, and a sulfide moiety through which the molecule is fixed at the gold resonant surface as a molecular layer in an easy and reproducible way. The sensor is characterized by evaluating the response in function of the uranyl concentration in aqueous solutions of different compositions and real-life samples, such as tap water and seawater. The mechanism of the uranyl/MUPA interaction was investigated. Two different kinds of interactions of uranyl with the MUPA layer on gold from water are observed: a strong one and a weak one. In the presence of competing metal ions as Ca2+ and Mg2+, only the strong interaction takes place, with a high affinity constant (around 107 M-1), while a somewhat lower constant (i.e., around 106 M-1) is obtained in the presence of Mg2+ which forms stronger complexes with MUPA than Ca2+. Due to the high affinity and the good selectivity of the recognition element MUPA, a detection limit of a few µg L-1 is reached directly in natural water samples without any time-consuming sample pretreatment, making it possible for rapid, in situ controls of uranyl by the proposed sensor.

Towards intelligent packaging: BCP-EVOH@ optode for milk freshness measurement.

Intelligent packaging represents an emerging trend in the food industry, especially for highly perishable foods like milk and dairy products. Despite the apparent simplicity, miniaturized BCP-EVOH@ sensor, made of bromocresol purple (BCP) covalently bound to ethylene-vinyl alcohol (EVOH) copolymer, meets the goal of milk freshness monitoring during chilled storage, allowing both naked-eye evaluation and chemometric-assisted spoilage modelling and measurements.

Cathode Active Material Recycling from Spent Lithium Batteries: A Green (Circular) Approach Based on Deep Eutectic Solvents.

The transition to a circular economy vision must handle the increasing request of metals required to satisfy the battery industry; this can be obtained by recycling and feeding back secondary raw materials recovered through proper waste management. Here, a novel and green proof-of-concept was developed, based on deep eutectic solvents (DESs) to fully and easily recover valuable metals from various cathode active materials, including LiMn2 O4 , LiNi0.5 Mn1.5 O4 , and LiNi0.8 Co0.2 O2 . DES composed of choline chloride and lactic acid could leach Li, Mn, Co, and Ni, achieving efficiency of 100 % under much milder conditions with respect to the previous literature. For the first time, to our best knowledge, a two-step approach was reported in the case of LiNi0.8 Co0.2 O2 for selective recovery of Li, Co, and Ni with high yield and purity. Furthermore, other cathode components, namely aluminum current collector and binder, were found to be not dissolved by the proposed DES, thus making a simple separation from the active material possible. Finally, this strategy was designed to easily regenerate and reuse the leaching solvents for more than one extraction, thus further boosting process sustainability.

SPR-Optical Fiber-Molecularly Imprinted Polymer Sensor for the Detection of Furfural in Wine.

A surface plasmon resonance (SPR) platform, based on a D-shaped plastic optical fiber (POF), combined with a biomimetic receptor, i.e., a molecularly imprinted polymer (MIP), is proposed to detect furfural (2-furaldheide, 2-FAL) in fermented beverages like wine. MIPs have been demonstrated to be a very convenient biomimetic receptor in the proposed sensing device, being easy and rapid to develop, suitable for on-site determinations at low concentrations, and cheap. Moreover, the MIP film thickness can be changed to modulate the sensing parameters. The possibility of performing single drop measurements is a further favorable aspect for practical applications. For example, the use of an SPR-MIP sensor for the analysis of 2-FAL in a real life matrix such as wine is proposed, obtaining a low detection limit of 0.004 mg L-1. The determination of 2-FAL in fermented beverages is becoming a crucial task, mainly for the effects of the furanic compounds on the flavor of food and their toxic and carcinogenic effect on human beings.

Disposable and Low-Cost Colorimetric Sensors for Environmental Analysis.

Environmental contamination affects human health and reduces the quality of life. Therefore, the monitoring of water and air quality is important, ensuring that all areas are acquiescent with the current legislation. Colorimetric sensors deliver quick, naked-eye detection, low-cost, and adequate determination of environmental analytes. In particular, disposable sensors are cheap and easy-to-use devices for single-shot measurements. Due to increasing requests for in situ analysis or resource-limited zones, disposable sensors' development has increased. This review provides a brief insight into low-cost and disposable colorimetric sensors currently used for environmental analysis. The advantages and disadvantages of different colorimetric devices for environmental analysis are discussed.

Chelating Agents in Soil Remediation: A New Method for a Pragmatic Choice of the Right Chelator.

Soil pollution by metal ions constitutes one of the most significant environmental problems in the world, being the ecosystems of extended areas wholly compromised. The remediation of soils is an impelling necessity, and different methodologies are used and studied for reaching this goal. Among them, the application of chelating agents is one of the most promising since it could allow the removal of metal ions while preserving the most meaningful properties of the original soils. The research in this field requires the joined contribute of different expertise spanning from biology to chemistry. In this work, we propose a parsimonious and pragmatic approach for screening among a range of potential chelating agents. This methodology, the Nurchi's method, is based on an extension of the Reilley procedure for EDTA titrations. This allows forecasting the binding ability of chelating agents toward the target polluting metal ions and those typically found in soils, based on the knowledge of the related protonation and complex formation constants. The method is thoroughly developed, and then tested by application to some representative cases. Its use and relevance in biomedical and industrial applications is also discussed.

Development of a Dye-Based Device to Assess the Poultry Meat Spoilage. Part II: Array on Act.

This work presents a colorimetric dye-based array for naked-eye detection of chicken meat spoilage. The array is obtained by fixing five acid-base indicators, m-cresol purple (1), o-cresol red (2), bromothymol blue (3), thymol blue (4), and chlorophenol red (5), and a sensing molecule specific for thiols, 5,5'-dithiobis(2-nitrodibenzoic acid), called Ellman's reagent (6), on a cellulose-based support. The dyes, being permanently charged, are fixed on the support via ion-exchange. The entire degradation process of beast poultry meat, at ambient temperature and in a domestic fridge, is followed by the change of the color of the array, placed in the headspace over the meat samples. The device is set after selection of the most suitable starting form, which could be the acidic or the basic color of indicators, being the proper dye concentration and the dimension of the spots already established. Basing on sensors colors, we identified three levels of the degradation process of chicken meat, named SAFE, WARNING, and HAZARD. By instrumental analysis, we demonstrated that sensors response was correlated to volatile organic compounds (VOCs) composition in the headspace and, thus, to meat spoilage progress. We demonstrated that biogenic amines (BAs), commonly considered a critical spoilage marker, are indeed produced into the samples but never present in the headspace, even in traces, during the investigated time-lapse. The VOC evolution nevertheless allows one to assign the sample as WARNING and further HAZARD. Some indicators turned out to be more informative than others, and the best candidates for a future industrial application resulted in a bromothymol blue (3)-, chlorophenol red (5)-, and Ellman's reagent (6)-based array.