Structural retrofitting of RC slabs using bamboo fibre laminate: Flexural performance and crack patterns.

Enhancing the durability of structural elements is a viable approach to promote sustainability in civil engineering. Research has shown that well-maintained slabs outperform degraded ones, which deteriorate rapidly due to insufficient upkeep. The occurrence of cracking and deformation in slabs subjected to sustained loads significantly impacts their functionality. However, the implementation of appropriate retrofitting techniques utilizing locally available materials can effectively minimize deflection and crack propagation while also improving flexural capacity. This particular study aimed to evaluate the flexural performance of slabs that were retrofitted using bamboo fibre laminate (BFL). Also, the study investigated two alternative replacement methods alongside the conventional mix; one involved replacing all fine aggregates with ceramic fine aggregate and the other involved a complete replacement of coarse aggregates with ceramic coarse aggregate. These mixes were represented in both the retrofitted and non-retrofitted samples. The retrofitting process included using the combined external bonding and near surface-mounted method. Twelve slab samples were made, with six being non-retrofitted and the other six retrofitted with BFL. Each of the samples had dimensions of 300 mm × 300 mm × 50 mm for reinforced concrete (RC) slabs. The slabs were tested employing the three point-bending system, and the retrofitted slabs with the conventional mix exhibited the highest ultimate failure load and flexural strength (62.1 kN), which compared to the non-retrofitted slabs of the same mix was a 60.76% increase. Additionally, the study did a thorough analysis of the presence of flexural and diagonal shear cracks, as well as the occurrence of debonding between BFL and the slabs. Non-destructive tests were also conducted on the slab samples to further confirm accurate results. These findings offer helpful insights into the development and application of a sustainable retrofitting material that can remarkably improve RC slabs.

A study on the strength and durability characteristics of fiber-reinforced recycled aggregate concrete modified with supplementary cementitious material.

Recycled aggregate (RA) made from waste concrete is an environmentally friendly alternative to natural aggregate (NA) for concrete manufacturing. However, compared to NA concrete, concrete produced with recycled aggregates has poor characteristics. Supplementary cementitious materials (SCMs) can be used to enhance the poor properties of recycled aggregate concrete (RAC). Silica fume and fly ash are commonly used SCMs in the World, but their high usage led to a shortage of silica fume and fly ash. Still, the deficiency of these materials in large parts of the world is a challenge that requires exploring alternative feedstock materials for the construction industry in the coming years. Wheat straw ash (WSA) is an agricultural waste product that could be used as an alternative SCM due to its pozzolanic behavior to enhance the properties of RAC. In addition, concrete is brittle and needs reinforcement, for which polypropylene fibers (PPFs) can be used. The current research examines the mechanical characteristics of fiber-reinforced RAC, including compressive strength, splitting tensile strength, and ductility performance. Durability indicators, such as chloride diffusion, chloride penetration, acid resistance, and water absorption test, were also assessed. The results showed that concrete samples with 10% WSA, 50% RA and 1.5% PPFs had the highest compressive and splitting tensile strength, 60.2 MPa and 7.25 MPa, respectively, representing increases of 24.75% and 30.65%, as compared to plain samples at 56 days. In these samples, water absorption was reduced by 13% due to the finer WSA particles resulting in the lowest reduction in strength and mass recorded when exposing concrete samples to acidic media. The statistical analysis also validated that irrespective of WSA and PPFs, the concrete with 0% RA had the highest performance in strength and durability behavior. The study showed that WSA and PPFs might be employed in tandem to offset the poor behavior of RA, enhance the bond between fibers and concrete, and improve the mechanical strength and durability performance of RAC, thus demonstrating its suitability as a sustainable and economical construction material.

Determining engineering properties of ultra-high-performance fiber-reinforced geopolymer concrete modified with different waste materials.

Reprocessing solid waste materials is a low-cost method of preserving the environment, conserving natural resources, and reducing raw material consumption. Developing ultra-high-performance concrete materials requires an immense quantity of natural raw materials. The current study seeks to tackle this issue by evaluating the effect of various discarded materials, waste glass (GW), marble waste (MW), and waste rubber powder (WRP) as a partial replacement of fine aggregates on the engineering properties of sustainable ultra-high-performance fiber-reinforced geopolymer concrete (UHPGPC). Ten different mixtures were developed as a partial substitute for fine aggregate, each containing 2% double-hooked end steel fibers, 5%, 10%, and 15% GW, MW, and WRP. The present study assessed the fresh, mechanical, and durability properties of UHPGPC. In addition, to evaluate concrete development at the microscopic level due to the addition of GW, MW, and WRP. Spectra of X-ray diffraction (XRD), thermogravimetric analysis (TGA), and mercury intrusion (MIP) tests were conducted. The test results were compared to current trends and procedures identified in the literature. According to the study, adding 15% marble waste and 15% waste rubber powder reduced ultra-high-performance geopolymer concrete's strength, durability, and microstructure properties. Even so, adding glass waste improved the properties, as the sample with 15% GW had the highest compressive strength of 179 MPa after 90 days. Furthermore, incorporating glass waste into the UHPGPC resulted in a good reaction between the geopolymerization gel and the waste glass particles, enhancing strength properties and a packed microstructure. The inclusion of glass waste in the mix resulted in the control of crystal-shaped humps of quartz and calcite, according to XRD spectra. During the TGA analysis, the UHPGPC with 15% glass waste had the minimum weight loss (5.64%) compared to other modified samples.

Experimental study on the properties of ultra-high-strength geopolymer concrete with polypropylene fibers and nano-silica.

Because of the recent progress in materials properties, specifically high-strength concrete, further research is needed to evaluate its suitability, understanding, and performance in the modern-day world. This research aims to enhance the performance of ultra-high-strength geopolymer concrete (UHS-GPC) by adding nano-silica (NS) and polypropylene fibers (PPFs). Three 1%, 2%, and 3% different amounts of PPFs and three NS 5%, 10%, and 15% were utilized in the samples. Various performance parameters of UHS-GPC were evaluated, such as fresh property, compressive strength, modulus of elasticity split tensile, flexural and bonding strength, drying shrinkage, load-displacement test, fracture performance, and elevated temperature. The test outcomes showed that by raising the percentage of PPFs and NS to the allowable limit, the performance of UHS-GPC can be improved significantly. The most improved performance of UHS-GPC was obtained at 2% polypropylene fibers and 10% nano-silica, as the compressive, splitting tensile, flexural. Bond strength was improved by 17.07%, 47.1%, 36.52, and 37.58%, and the modulus of elasticity increased by 31.4% at 56 days. The study showed that the sample with 2% PPFs and 10% NS had excellent performance in the load-displacement test, drying shrinkage, fracture behavior, and elevated temperature. At 750°C elevated temperature, the samples' strength was reduced drastically, but at 250°C, the modified samples showed good resistance to heat by retaining their compressive strength to some degree. The present work showed the suitability of PPFs and NS to develop ultra-high-strength geopolymer concrete, which can be used as a possible alternate material for Portland cement-based concrete.

Behavior of Concrete Reinforced with Date Palm Fibers.

In recent decades, researchers have begun to investigate innovative sustainable construction materials for the development of greener and more environmentally friendly infrastructures. The main purpose of this article is to investigate the possibility of employing date palm tree waste as a natural fiber alternative for conventional steel and polypropylene fibers (PPFs) in concrete. Date palm fibers are a common agricultural waste in Middle Eastern nations, particularly Saudi Arabia. As a result, this research examined the engineering properties of high-strength concrete using date palm fibers, as well as the performance of traditional steel and PPF concrete. The concrete samples were made using 0.0%, 0.20%, 0.60%, and 1.0% by volume of date palm, steel, and polypropylene fibers. Ten concrete mixtures were made in total. Compressive strength, flexural strength, splitting tensile strength, density, ultrasonic pulse velocity (UPV), water absorption capability, and water permeability tests were performed on the fibrous-reinforced high-strength concrete. With a 1% proportion of date palm, steel, and polypropylene fibers, the splitting tensile strength improved by 17%, 43%, and 16%, respectively. By adding 1% fiber, flexural strength was increased by 60% to 85%, 67% to 165%, and 61% to 79%. In addition, date palm fibers outperformed steel and PPFs in terms of density, UPV, and water permeability. As a result, date palm fibers might potentially be employed in the present construction sector to improve the serviceability of structural elements.

Experimental Investigation of Hybrid Beams Utilizing Ultra-High Performance Concrete (UHPC) as Tension Reinforcement.

Ultra-high performance concrete (UHPC) is a new generation concrete with extremely high tensile and compressive strength, high durability, and ductility. UHPC offers tremendous opportunities for use in new thin and slender structural concrete elements and repair of existing concrete structures and has an excellent potential to replace conventional steel reinforcement in normal concrete (NC) members. This paper investigated the potential application of a hybrid NC-UHPC beam using a thin UHPC layer on the tension face to cater to tensile stresses, eliminating the need for passive steel reinforcement. Four-point flexural load tests were performed on 24 composite beams with a thin UHPC layer overlaid with NC. The parameters considered include the thickness of the UHPC layer, depth, and span of the beam. A linear behavior categorizes the flexural behavior of the hybrid NC-UHPC beam up to the ultimate load, after which the hybrid beam shows a non-brittle failure, and softening ensues associated with cracking, increased deflection, and loss of load resisting capacity. The unfinished top surface of the UHPC layer and the overlying NC developed a full composite action without any slip. It was found that a two-day self-curing of the UHPC layer was found to be essential for the development of a strong bond between the layers. The random dispersion and orientation of steel fibers in the UHPC can lead to a decreased tensile response for larger hybrid NC-UHPC beams. The experimental results validate the potential of hybrid NC-UHPC beams as an attractive, structurally feasible, and alternative sound form of construction in terms of their high flexural strength and corrosion-free service life. The proposed unreinforced hybrid system could be used in the construction of precast beams and slabs for residential as well as industrial buildings. Further research, including full-scale load testing of the hybrid beam, is needed prior to practical applications.

Rheological, Aging, and Microstructural Properties of Polycarbonate and Polytetrafluoroethylene Modified Bitumen.

Deterioration of asphalt pavements due to massive load of vehicles and climatic variation has demanded the use of pavements construction material with an excellent resilience characteristic, resistance to permanent deformation, and most importantly, a much longer service lifespan. The main structural distresses in pavement construction are permanent deformation at high temperatures and fatigue cracking under repetitive traffic loadings. To comprehensively investigate the performance of bitumen penetration grade (PG) 70 against rutting, fatigue, and high temperature cracking in hot mix asphalt (HMA) pavements, polycarbonate (PC) and polytetrafluoroethylene (PTFE) were used. The investigation of the internal structure, rheological, and physical properties of base and modified bitumen (MB) mixes with different percentages of modifiers (0%, 2.5%, and 5%) by weight were performed via scanning electron microscope (SEM), Fourier transform infrared spectroscopy (FTIR) analysis, X-ray diffraction (XRD) pattern analysis, rolling thin-film oven test (RTFOT), pressurized aging vessel (PAV), dynamic shear rheometer (DSR), rotational viscosity (RV), and bending beam rheometer (BBR). The results of the RV test indicate that modification of neat bitumen with polycarbonate and polytetrafluoroethylene increased the viscosity for polycarbonate-modified bitumen (PCMB), polytetrafluoroethylene-modified bitumen (PTFEMB), and for a blend of PCMB-PTFEMB by 44%, 50%, and 55.75% at 135 °C and 111.10%, 127.80%, and 138.88% at 165 °C, accordingly. BBR test results revealed that modifiers increased the rigidity of neat bitumen by 74.8%, 75.8%, and 74.5% at -16 °C, -22 °C, and -28 °C, respectively.

A Scientometric Review on Mapping Research Knowledge for 3D Printing Concrete.

The scientometric analysis is statistical scrutiny of books, papers, and other publications to assess the "output" of individuals/research teams, organizations, and nations, to identify national and worldwide networks, and to map the creation of new (multi-disciplinary) scientific and technological fields that would be beneficial for the new researchers in the particular field. A scientometric review of 3D printing concrete is carried out in this study to explore the different literature aspects. There are limitations in conventional and typical review studies regarding the capacity of such studies to link various elements of the literature accurately and comprehensively. Some major problematic phases in advanced level research are: co-occurrence, science mapping, and co-citation. The sources with maximum articles, the highly creative researchers/authors known for citations and publications, keywords co-occurrences, and actively involved domains in 3D printing concrete research are explored during the analysis. VOS viewer application analyses bibliometric datasets with 953 research publications were extracted from the Scopus database. The current study would benefit academics for joint venture development and sharing new strategies and ideas due to the graphical and statistical depiction of contributing regions/countries and researchers.

Investigating the Bond Strength of FRP Rebars in Concrete under High Temperature Using Gene-Expression Programming Model.

In recent times, the use of fibre-reinforced plastic (FRP) has increased in reinforcing concrete structures. The bond strength of FRP rebars is one of the most significant parameters for characterising the overall efficacy of the concrete structures reinforced with FRP. However, in cases of elevated temperature, the bond of FRP-reinforced concrete can deteriorate depending on a number of factors, including the type of FRP bars used, its diameter, surface form, anchorage length, concrete strength, and cover thickness. Hence, accurate quantification of FRP rebars in concrete is of paramount importance, especially at high temperatures. In this study, an artificial intelligence (AI)-based genetic-expression programming (GEP) method was used to predict the bond strength of FRP rebars in concrete at high temperatures. In order to predict the bond strength, we used failure mode temperature, fibre type, bar surface, bar diameter, anchorage length, compressive strength, and cover-to-diameter ratio as input parameters. The experimental dataset of 146 tests at various elevated temperatures were established for training and validating the model. A total of 70% of the data was used for training the model and remaining 30% was used for validation. Various statistical indices such as correlation coefficient (R), the mean absolute error (MAE), and the root-mean-square error (RMSE) were used to assess the predictive veracity of the GEP model. After the trials, the optimum hyperparameters were 150, 8, and 4 as number of chromosomes, head size and number of genes, respectively. Different genetic factors, such as the number of chromosomes, the size of the head, and the number of genes, were evaluated in eleven separate trials. The results as obtained from the rigorous statistical analysis and parametric study show that the developed GEP model is robust and can predict the bond strength of FRP rebars in concrete under high temperature with reasonable accuracy (i.e., R, RMSE and MAE 0.941, 2.087, and 1.620, and 0.935, 2.370, and 2.046, respectively, for training and validation). More importantly, based on the FRP properties, the model has been translated into traceable mathematical formulation for easy calculations.

Investigation of the effectiveness of CFRP strengthening of concrete made with recycled waste PET fine plastic aggregate.

In recent decades, several studies have considered the use of plastic waste as a partial substitute for aggregate in green concrete. Such concrete has been limited to non-structural applications due to its low strength. This raises whether such concrete can be enhanced for use in some structural applications. This paper reports an attempt to develop a structural-grade concrete containing plastic waste aggregate with high proportions of substitution and confined with carbon fiber reinforced polymer (CFRP) fabrics. Experimental research was conducted involving the casting and testing 54 plain and confined concrete cylinders. A concrete mixture was designed in which the fine aggregate was partially replaced by polyethylene terephthalate (PET) waste plastic at ratios of 0%, 25%, and 50%, and with different w/c ratios of 0.40, 0.45, and 0.55. The results show that confinement has a substantial positive effect on the compressive behavior of PET concrete. The enhancement efficiency increases by 8-190%, with higher enhancement levels for higher substitution ratios. Adding one layer of CFRP fabric raises the ultimate strength of samples that have lost compressive strength to a level close to that of unconfined samples not containing PET. This confinement is accompanied by an increase in the slope of the stress-strain curve and greater axial and lateral strain values at failure. For the specimens confined by CFRP fabric, PET aggregate can be used as a partial substitute for sand at a replacement ratio of up to 50% by volume for structural applications. This paper also considers the ability of existing models to predict the strength of confined-PET concrete circular cross-sections by comparing model predictions with experimental results. The strength of confined PET concrete elements can't be accurately predicted by any of the models that are already out there. It's important to come up with a new model for these elements.

Mechanical and Durability Performance of Coconut Fiber Reinforced Concrete: A State-of-the-Art Review.

The push for sustainability in the construction sector has demanded the use of increasingly renewable resources. These natural fibers are biodegradable and non-toxic, and their mechanical capabilities are superior to those of synthetic fibers in terms of strength and durability. A lot of research recommends coconut fibers as an alternative to synthetic fibers. However, the knowledge is scattered, and no one can easily judge the suitability of coconut fibers in concrete. This paper presents a summary of research progress on coconut fiber (natural fibers) reinforced concrete. The effects of coconut fibers on the properties of concrete are reviewed. Factors affecting the fresh, hardened, and durability properties of concrete reinforced with coconut fiber are discussed. Results indicate that coconut fiber improved the mechanical performance of concrete due to crack prevention, similar to the synthetic fibers but decreased the flowability of concrete. However, coconut fibers improved flexure strength more effectively than compressive strength. Furthermore, improvement in some durability performance was also observed, but less information is available in this regard. Moreover, the optimum dose is an important parameter for high-strength concrete. The majority of researchers indicate that 3.0% coconut fiber is the optimum dose. The overall study demonstrates that coconut fibers have the creditability to be used in concrete instead of synthetic fibers.

Advanced Machine Learning Modeling Approach for Prediction of Compressive Strength of FRP Confined Concrete Using Multiphysics Genetic Expression Programming.

The purpose of this article is to demonstrate the potential of gene expression programming (GEP) in anticipating the compressive strength of circular CFRP confined concrete columns. A new GEP model has been developed based on a credible and extensive database of 828 data points to date. Numerous analyses were carried out to evaluate and validate the presented model by comparing them with those presented previously by different researchers along with external validation comparison. In comparison to other artificial intelligence (AI) techniques, such as Artificial Neural Networks (ANN) and the adaptive neuro-fuzzy interface system (ANFIS), only GEP has the capability and robustness to provide output in the form of a simple mathematical relationship that is easy to use. The developed GEP model is also compared with linear and nonlinear regression models to evaluate the performance. Afterwards, a detailed parametric and sensitivity analysis confirms the generalized nature of the newly established model. Sensitivity analysis results indicate the performance of the model by evaluating the relative contribution of explanatory variables involved in development. Moreover, the Taylor diagram is also established to visualize how the proposed model outperformed other existing models in terms of accuracy, efficiency, and being closer to the target. Lastly, the criteria of external validation were also fulfilled by the GEP model much better than other conventional models. These findings show that the presented model effectively forecasts the confined strength of circular concrete columns significantly better than the previously established conventional regression-based models.

Flexural Performance of RC Beams Strengthened with Externally-Side Bonded Reinforcement (E-SBR) Technique Using CFRP Composites.

Reinforced concrete (RC) structures necessitate strengthening for various reasons. These include ageing, deterioration of materials due to environmental effects, trivial initial design and construction, deficiency of maintenance, the advancement of design loads, and functional changes. RC structures strengthening with the carbon fiber reinforced polymer (CFRP) has been used extensively during the last few decades due to their advantages over steel reinforcement. This paper introduces an experimental approach for flexural strengthening of RC beams with Externally-Side Bonded Reinforcement (E-SBR) using CFRP fabrics. The experimental program comprises eight full-scale RC beams tested under a four-point flexural test up to failure. The parameters investigated include the main tensile steel reinforcing ratio and the width of CFRP fabrics. The experimental outcomes show that an increase in the tensile reinforcement ratio and width of the CFRP laminates enhanced the first cracking and ultimate load-bearing capacities of the strengthened beams up to 141 and 174%, respectively, compared to the control beam. The strengthened RC beams exhibited superior energy absorption capacity, stiffness, and ductile response. The comparison of the experimental and predicted values shows that these two are in good agreement.