Enhanced LWIR response of InP/InAsP quantum discs-in-nanowire array photodetectors by photogating and ultra-thin ITO contacts.

Here we report on an experimental and theoretical investigation of the long-wavelength infrared (LWIR) photoresponse of photodetectors based on arrays of three million InP nanowires with axially embedded InAsP quantum discs. An ultra-thin top indium tin oxide contact combined with a novel photogating mechanism facilitates an improved LWIR normal incidence sensitivity in contrast to traditional planar quantum well photodetectors. The electronic structure of the quantum discs, including strain and defect-induced photogating effects, and optical transition matrix elements were calculated by an 8-bandk·psimulation along with solving drift-diffusion equations to unravel the physics behind the generation of narrow linewidth intersubband signals observed from the quantum discs.

Branched-gallium phosphide nanowires seeded by palladium nanoparticles.

Palladium nanoparticles were produced by a chemical reagent-free and versatile method called spark ablation with control over particle size and density. These nanoparticles were used as catalytic seed particles for gallium phosphide nanowire growth by metalorganic vapour-phase epitaxy. Controlled growth of GaP nanowires using significantly small Pd nanoparticles between 10 and 40 nm diameter was achieved by varying several growth parameters. Low V/III ratios below 2.0 promote higher Ga incorporation into the Pd nanoparticles. Moderate growth temperatures under 600 °C avoid kinking and undesirable GaP surface growth. In addition, a second batch of palladium nanoparticles of concentration up to 1000 particlesµm-2was deposited onto the GaP nanowires. Subsequently, three-dimensional nanostructures evolved, with branches growing along the surface of the GaP nanowires. The GaP nanowires revealed a zinc blende structure with multiple twinning and a PdGa phase at the tip of the nanowires and branches.

Size-resolved characterization of particles >10 nm emitted to air during metal recycling.

BACKGROUND: In the strive towards a circular economy, metal waste recycling is a growing industry. During the recycling process, particulate matter containing toxic and allergenic metals will be emitted to the air causing unintentional exposure to humans and environment. OBJECTIVE: In this study detailed characterization of particle emissions and workplace exposures were performed, covering the full size range from 10 nm to 10 µm, during recycling of three different material flows: Waste of electrical and electronic equipment (WEEE), metal scrap, and cables. METHODS: Both direct-reading instruments (minute resolution), and time-integrated filter measurements for gravimetric and chemical analysis were used. Additionally, optical sensors were applied and evaluated for long-term online monitoring of air quality in industrial settings. RESULTS: The highest concentrations, in all particle sizes, and with respect both to particle mass and number, were measured in the WEEE flow, followed by the metal scrap flow. The number fraction of nanoparticles was high for all material flows (0.66-0.86). The most abundant metals were Fe, Al, Zn, Pb and Cu. Other elements of toxicological interest were Mn, Ba and Co. SIGNIFICANCE: The large fraction of nanoparticles, and the fact that their chemical composition deviate from that of the coarse particles, raises questions that needs to be further addressed including toxicological implications, both for humans and for the environment.

Mo3Ni2N Nanoparticle Generation by Spark Discharge.

Spark ablation is an advantageous method for the generation of metallic nanoparticles with defined particle sizes and compositions. The reaction of the metal particles with the carrier gas during the synthesis and, therefore, the incorporation of those light elements into structural voids or even compound formation was confirmed for hydrides and oxides but has only been suspected to occur for nitrides. In this study, dispersed nanoparticles of Mo3Ni2N and Mo with Janus morphology, and defined particle sizes were obtained by spark discharge generation as a result of carrier gas ionization and characterized using transmission electron microscopy and powder X-ray diffraction. Metal nitrides possess beneficial catalytic and thermoelectric properties, as well as high hardness and wear resistance. Therefore, this method offers the possibility of controlled synthesis of materials which are interesting for numerous applications.

Critical assessment of the performance of next-generation carbon-based adsorbents for CO2 capture focused on their structural properties.

Carbon dioxide emissions and their sharply rising effect on global warming have encouraged research efforts to develop efficient technologies and materials for CO2 capture. Post-combustion CO2 capture by adsorption using solid materials is considered an attractive technology to achieve this goal. Templated materials, such as Zeolite Templated-Carbons and MOF-Derived Carbons, are considered as the next-generation carbon adsorbent materials, owing to their outstanding textural properties (high surface areas of ca. 4000 m2 g-1 and micropore volumes of ca. 1.7 cm3 g-1) and their versatility for surface functionalization. These materials have demonstrated remarkable CO2 adsorption capacities and CO2/N2 selectivities up to ca. 5 mmol g-1 and 100, respectively, at 298 K and 1 bar, and low isosteric heat of adsorption at zero coverage of ca. 12 kJ mol-1. Herein, a review of the advances in preparation of ZTCs and MDCs for CO2 capture is presented, followed by a critical analysis of the effects of textural properties and surface functionality on CO2 adsorption, including CO2 uptake, CO2/N2 selectivity, and isosteric heat of adsorption. This analysis led to the introduction of a Vmicrox N-content factor to evaluate the interplay between N-content and textural properties to maximize the CO2 uptake. Despite their promising performance in CO2 uptake, further testing using mixtures and impurities, and studies on adsorbent regeneration, and cyclic operation are desirable to demonstrate the stability of the MDCs and ZTCs for large scale processes. In addition, advances in scale-up syntheses and their economics are needed.