Preparation and Performance Study of Boron Adsorbent from Plasma-Grafted Polypropylene Melt-Blown Fibers.

In this study, the plasma graft polymerization technique was used to graft glycidyl methacrylate (GMA) onto polypropylene (PP) melt-blown fibers, which were subsequently aminated with N-methyl-D-glucamine (NMDG) by a ring-opening reaction, resulting in the formation of a boron adsorbent denoted as PP-g-GMA-NMDG. The optimal conditions for GMA concentration, grafting time, grafting temperature, and the quantity of NMDG were determined using both single factor testing and orthogonal testing. These experiments determined the optimal process conditions to achieve a high boron adsorption capacity of PP-g-GMA-NMDG. Fourier-transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), energy dispersion spectrum analysis (EDS), and water contact angle measurements were performed to characterize the prepared adsorbent. Boron adsorption experiments were carried out to investigate the effects of pH, time, temperature, and boron concentration on the boron adsorption capacity of PP-g-GMA-NMDG. The adsorption isotherms and kinetics of PP-g-GMA-NMDG for boron were also studied. The results demonstrated that the adsorption process followed a pseudo-second-order kinetic model and a Langmuir isothermal model. At a pH of 6, the maximum saturation adsorption capacity of PP-g-GMA-NMDG for boron was 18.03 ± 1 mg/g. In addition, PP-g-GMA-NMDG also showed excellent selectivity for the adsorption of boron in the presence of other cations, such as Na+, Mg2+, and Ca2+, PP-g-GMA-NMDG, and exhibited excellent selectivity towards boron adsorption. These results indicated that the technique of preparing PP-g-GMA-NMDG is both viable and environmentally benign. The PP-g-GMA-NMDG that was made has better qualities than other similar adsorbents. It has a high adsorption capacity, great selectivity, reliable repeatability, and easy recovery. These advantages indicated that the adsorbents have significant potential for widespread application in the separation of boron in water.

Preparation and Adsorption Performance of Boron Adsorbents Derived from Modified Waste Feathers.

This research focuses on modifying discarded feathers by grafting glycidyl methacrylate (GMA) onto their surface through thiolation, followed by an epoxy ring-opening reaction with N-methyl-D-glucamine (NMDG) to synthesize feather-based boron adsorbents. Optimization of the adsorbent preparation conditions was achieved through single-factor experiments, varying temperature, time, GMA concentration, and initiator dosage. The synthesized adsorbent (F-g-GMA-NMDG) underwent characterization using Fourier transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and X-ray diffraction (XRD). The adsorption behavior of the adsorbent was studied, and its boron adsorption capacity at different temperatures was determined through static adsorption kinetic curves. Analysis of adsorption isotherms, kinetics, and thermodynamics was conducted. Results indicate that the boron adsorption process by F-g-GMA-NMDG follows a pseudo-second-order model. The adsorption process is endothermic, with higher temperatures promoting adsorption efficiency. Gibbs free energy (ΔG) confirms the spontaneity of the adsorption process. Enhanced adsorption efficacy was observed under neutral and acidic pH conditions. After four cycles, the adsorbent maintained its adsorption efficiency, demonstrating its stability and potential for reuse. This study provides novel insights into both the treatment of discarded feathers and the development of boron adsorbents.

Intravoxel incoherent motion magnetic resonance imaging reconstruction from highly under-sampled diffusion-weighted PROPELLER acquisition data via physics-informed residual feedback unrolled network.

Objective. The acquisition of diffusion-weighted images for intravoxel incoherent motion (IVIM) imaging is time consuming. This work aims to accelerate the scan through a highly under-sampling diffusion-weighted turbo spin echo PROPELLER (DW-TSE-PROPELLER) scheme and to develop a reconstruction method for accurate IVIM parameter mapping from the under-sampled data.Approach.The proposed under-sampling DW-TSE-PROPELLER scheme for IVIM imaging is that a few blades perb-value are acquired and rotated along theb-value dimension to cover high-frequency information. A physics-informed residual feedback unrolled network (PIRFU-Net) is proposed to directly estimate distortion-free and artifact-free IVIM parametric maps (i.e., the perfusion-free diffusion coefficientDand the perfusion fractionf) from highly under-sampled DW-TSE-PROPELLER data. PIRFU-Net used an unrolled convolution network to explore data redundancy in the k-q space to remove under-sampling artifacts. An empirical IVIM physical constraint was incorporated into the network to ensure that the signal evolution curves along theb-value follow a bi-exponential decay. The residual between the realistic and estimated measurements was fed into the network to refine the parametric maps. Meanwhile, the use of synthetic training data eliminated the need for genuine DW-TSE-PROPELLER data.Main results.The experimental results show that the DW-TSE-PROPELLER acquisition was six times faster than full k-space coverage PROPELLER acquisition and within a clinically acceptable time. Compared with the state-of-the-art methods, the distortion-freeDandfmaps estimated by PIRFU-Net were more accurate and had better-preserved tissue boundaries on a simulated human brain and realistic phantom/rat brain/human brain data.Significance.Our proposed method greatly accelerates IVIM imaging. It is capable of directly and simultaneously reconstructing distortion-free, artifact-free, and accurateDandfmaps from six-fold under-sampled DW-TSE-PROPELLER data.

Boron Adsorption Using NMDG-Modified Polypropylene Melt-Blown Fibers Induced by Ultraviolet Grafting.

Boron is in high demand in many sectors, yet there are significant flaws in current boron resource utilization. This study describes the synthesis of a boron adsorbent based on polypropylene (PP) melt-blown fiber using ultraviolet (UV)-induced grafting of Glycidyl methacrylate (GMA) onto PP melt-blown fiber, followed by an epoxy ring-opening reaction with N-methyl-D-glucosamine (NMDG). Using single-factor studies, grafting conditions such as the GMA concentration, benzophenone dose, and grafting duration were optimized. Fourier transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), X-ray diffraction (XRD), and water contact angle were used to characterize the produced adsorbent (PP-g-GMA-NMDG). The PP-g-GMA-NMDG adsorption process was examined by fitting the data with different adsorption settings and models. The results demonstrated that the adsorption process was compatible with the pseudo-second-order model and the Langmuir model; however, the internal diffusion model suggested that the process was impacted by both extra- and intra-membrane diffusion. According to thermodynamic simulations, the adsorption process was exothermic. At pH 6, the greatest saturation adsorption capacity to boron was 41.65 mg·g-1 for PP-g-GMA-NMDG. The PP-g-GMA-NMDG preparation process is a feasible and environmentally friendly route, and the prepared PP-g-GMA-NMDG has the advantages of high adsorption capacity, outstanding selectivity, good reproducibility, and easy recovery when compared to similar adsorbents, indicating that the reported adsorbent is promising for boron separation from water.

Selective and rapid removal of Mo(VI) from water using functionalized Fe3O4-based Mo(VI) ion-imprinted polymer.

Fe3O4 nanoparticles-based magnetic Mo(VI) surface ion-imprinted polymer (Mo(VI)-MIIP) was elaborated employing 4-vinyl pyridine as a functional monomer. The adsorbent preparation was confirmed by Fourier-transform infrared spectroscopy, scanning electron microscopy, energy dispersive X-ray spectrometry, X-ray diffraction, vibrating sample magnetometer, thermogravimetric analysis, and surface area analysis. Batch adsorption experiments showed that the maximum adsorption capacity of Mo(VI)-MIIP was 296.40 mg g-1 at pH 3, while that of the magnetic non-imprinted polymer (MNIP) was only 147.10 mg g-1. The adsorption isotherm model was well fitted by the Langmuir isotherm model. The adsorption experiments revealed that Mo(VI)-MIIP reached adsorption equilibrium within 30 min, and the kinetics data fitting showed that the pseudo-second-order kinetics model suitably described the adsorption process. Mo(VI)-MIIP exhibited an excellent adsorption selectivity to Mo(VI) in binary mixtures of Mo(VI)/Cr(VI), Mo(VI)/Cu(II), Mo(VI)/H2PO44-, Mo(VI)/Zn(II), and Mo(VI)/I-, with relative selectivity coefficients toward MNIP of 13.71, 30.27, 20.01, 23.53, and 15.89, respectively. After six consecutive adsorption-desorption cycles, the adsorption capacity of Mo(VI)-MIIP decreased by 9.5% (from 228.4 mg g-1 to 206.7 mg g-1 at initial Mo(VI) concentration of 250 mg L-1), demonstrating its reusability.

Ion-Imprinted Polypropylene Fibers Fabricated by the Plasma-Mediated Grafting Strategy for Efficient and Selective Adsorption of Cr(VI).

To improve the adsorption selectivity towards hexavalent chromium anion (Cr(VI)), surface Cr(VI)-imprinted polypropylene (PP) fibers were fabricated by the plasma-mediated grafting strategy. Hence, a non-thermal Rradio frequency discharge plasma irradiation followed by a gaseous phase grafting was used to load acrylic acid (AA) onto PP fibers, which was afterwards amidated with triethylenetetramine and subjected to imprinting with a Cr(VI) template. The plasma irradiation conditions, i.e., gas species, output power, pressure, and time, were optimized and then the influence of grafting time, pressure, and temperature on the grafting degree of AA was investigated. Scanning electron microscopy and Fourier transform infrared spectroscopy were used for the characterization of pristine and modified fibers and to confirm the synthesis success. The hydrophilicity of modified fibers was greatly improved compared with pristine PP fibers. The adsorption thermodynamics and kinetics of Cr(VI) were investigated, as well as the elution efficiency and reusability. The prepared imprinted fibers showed superior adsorption selectivity to Cr(VI) compared with non-imprinted fibers. Finally, the stability of the imprinted fibers against the oxidation ability of Cr(VI) is discussed.

Determination of total arsenic in coal and wood using oxygen flask combustion method followed by hydride generation atomic absorption spectrometry.

A simple and sensitive procedure for the determination of total arsenic in coal and wood was conducted by use of oxygen flask combustion (OFC) followed by hydride generation atomic absorption spectrometry (HGAAS). The effect of various items (composition of absorbent, standing time between the combustion and filtration, particle size and mass of sample) was investigated. Under the optimized conditions of the OFC method, nine certified reference materials were analyzed, and the values of arsenic concentration obtained by this method were in good accordance with the certified values. The limit of detection (LOD) and relative standard deviation (RSD) of the method were 0.29 microg g(-1) and less than 8%, respectively. In addition, eight kinds of coals and four chromated copper arsenate (CCA)-treated wood wastes were analyzed by the present method, and the data were compared to those from the microwave-acid digestion (MW-AD) method. The determination of arsenic in solid samples was discussed in terms of applicable scope and concentration range of arsenic.

Arsenic speciation in marine product samples: comparison of extraction-HPLC method and digestion-cryogenic trap method.

For the arsenic speciation in marine product samples, two types of pretreatment-analysis combination were compared. One is the combination of solvent extraction and high performance liquid chromatography (HPLC) followed by a highly sensitive arsenic detection, while the other is the combination of alkaline digestion and cryogenic trap (CT) method followed by a highly sensitive arsenic detection. For six certified reference materials (CRMs) of marine animal samples, the concentrations of arsenobetaine (AsB) obtained from the extraction-HPLC method were very consistent with those of trimethylated arsenic species measured by the digestion-CT method. For four seaweed samples, the determination of three arsenosugars (Sugar-1, Sugar-2, and Sugar-3) was favorably carried out by the extraction-HPLC method. Those seaweed samples were also subjected to the digestion-CT method, and the amounts of dimethylated arsenic species measured by the method were approximately equal to the sum of the amounts of dimethylarsinic acid (DMAA) and three arsenosugars (Sugar-1+Sugar-2+Sugar-3) obtained from the extraction-HPLC method.

Determination of mercury in ash and soil samples by oxygen flask combustion method--cold vapor atomic fluorescence spectrometry (CVAFS).

A simple method was developed for the determination of mercury (Hg) in coal fly ash (CFA), waste incineration ash (WIA), and soil by use of oxygen flask combustion (OFC) followed by cold vapor atomic fluorescence spectrometry (CVAFS). A KMnO4 solution was used as an absorbent in the OFC method, and the sample containing a combustion agent and an ash or soil sample was combusted by the OFC method. By use of Hg-free graphite as the combustion agent, the determination of Hg in ash and soil was successfully carried out; the Hg-free graphite was prepared by use of a mild pyrolysis procedure at 500 degrees C. For six certified reference materials (three CFA samples and three soil samples), the values of Hg obtained by this method were in good agreement with the certified or reference values. In addition, real samples including nine CFAs collected from some coal-fired power plants, five WIAs collected from waste incineration plants, and two soils were analyzed by the present method, and the data were compared to those from microwave-acid digestion (MW-AD) method.