Pressure dependent conduction of individual multi-walled carbon nanotubes: the effect of mechanical distortions.

Multi-walled carbon nanotubes (MWCNTs) show an oscillation in electrical resistance (from I-V measurements) during mechanical distortion in which peak separation is inversely correlated with the diameter of the MWCNTs. These results provide the first experimental support of the theoretical prediction that distortion causes Van Hove singularities and Dirac cones in MWCNTs to misalign and cause the opening of the band gap, and suggest that when fabricating contacts for CNTs for device applications, the pressure caused by the contact deposition method must be taken into account for manufacturing devices with consistent properties.

Experimental Measurement of Angular and Overlap Dependence of Conduction between Carbon Nanotubes of Identical Chirality and Diameter.

Measurement of the angular and overlap dependence of the conduction between two identical carbon nanotubes (CNTs), with the same diameter and chirality, has only been possible through theoretical calculations; however, our observation of increased resistance adjacent to the junction between two CNTs facilitates such measurements. Since electrical resistance was found to increase with increased diameter ratio, applying 10 V to one of dissimilar diameter CNTs results in cleavage at the junction. Manipulation of the resulting identical CNTs (created by cutting a single CNT) allows for the direct measurement of the angular and parallel overlap conduction. Angular (13° < θ < 63°) dependence shows two minima (22° and 44°) and a maximum at 30°, and conduction between parallel CNTs increases with overall tip separation but shows a sinusoidal relationship with contact length, consistent with the concept of atomic scale registry.

Aqueous electromigration of single-walled carbon nanotubes and co-electromigration with copper ions.

The electromigration behaviour of raw and acid purified single walled carbon nanotubes (SWCNTs) in dilute aqueous systems (0.0034 mg mL-1), in the absence of surfactant, with the addition of either 0.85 M acetic acid or 0.1 M CuSO4, was evaluated using a 2-inch copper cathode and either a 2-inch copper or 0.5-inch platinum anode. The results showed that the electromigration of raw SWCNTs (with a high catalyst residue) in the presence of CuSO4 resulted in the formation of a Cu-SWCNT composite material at the cathode. In contrast, acid purified SWCNTs were observed to diffuse to a copper anode, creating fibrillated agglomerates with "rice-grain"-like morphologies. Upon acidification with acetic acid (or addition of CuSO4) the direction of electromigration reversed towards the cathode as a result of coordination of Cu2+ to the functional groups on the SWCNT overcoming the inherent negative charge of the acid purified SWCNTs. The result was the co-deposition of SWCNTs and Cu metal on the cathode. Addition of 0.005 M EDTA sequesters some of the Cu2+ and resulted in the separation of metal decorated SWCNTs to the cathode and un-decorated SWCNTs to the anode. The resulting SWCNT and Cu/SWCNT deposits were characterized by Raman spectroscopy, XPS, SEM, EDS, and TEM.

Spatial and Contamination-Dependent Electrical Properties of Carbon Nanotubes.

Two-point probe and Raman spectroscopy have been used to investigate the effects of vacuum annealing and argon bombardment on the conduction characteristics of multiwalled carbon nanotubes (MWCNTs). Surface contamination has a large effect on the two-point probe conductivity measurements which results in inconsistent and nonreproducible contacts. The electric field under the contacts is enhanced which results in overlapping depletion regions when probe separations are small (<4 µm) causing very high resistances. Annealing at 200 and 500 °C reduced the surface contamination on the MWCNT, but high resistance contacts still did not allow intrinsic conductivity measurements of the MWCNT. The high resistance measured due to the overlapping depletion regions was not observed after annealing to 500 °C. Argon bombardment reduced the surface contamination more than vacuum annealing at 500 °C but caused a slight increase in the defects concentration, enabling the resistivity of the MWCNT to be calculated, which is found to be dependent on the CNT diameter. The observations have significant implications for future CNT-based devices.

Understanding the Effect of Functional Groups on the Seeded Growth of Copper on Carbon Nanotubes for Optimizing Electrical Transmission.

We present a study of the seeded growth of copper on the surface of two classes of single-walled carbon nanotubes (SWNTs) in order to compare the effects of surface functional groups. Pyridine-functionalized HiPco SWNTs and ultrashort SWNTs (US-SWNTs) were synthesized (py-SWNTs and py-US-SWNTs, respectively), and the functionality was used as seed sites for copper, via an aqueous electroless deposition reaction, as a comparison to the carboxylic acid functionality present on piranha-etched SWNTs and the native US-SWNTs. UV-vis spectroscopy demonstrated the take-up of Cu(II) ions by the functionalized SWNTs. TEM showed that the SWNTs with pyridine functionality more rapidly produced a more even distribution of copper seeds with a narrower size distribution (3-12 nm for py-US-SWNTs) than those SWNTs with oxygen functional groups (ca. 30 nm), showing the adventitious role of the pyridine functional group in the seeding process. Seed composition was confirmed as Cu(0) by XPS and SAED. Copper growth rate and morphology were shown to be affected by degree of pyridine functionality, the length of the SWNT, and the electroless reaction solvent used.