ABSTRACT
Two-dimensional (2D) mesoporous transition metal oxides are highly desired in various applications, but their fast and low-cost synthesis remains a great challenge. Herein, a Maillard reaction inspired microexplosion approach is applied to rapidly synthesize ultrathin 2D mesoporous tin oxide (mSnO2). During the microexplosion between granular ammonia nitrate with melanoidin at high temperature, the organic species can be carbonized and expanded rapidly due to the instantaneous release of gases, thus producing ultrathin carbonaceous templates with rich functional groups to effectively anchor SnO2 nanoparticles on the surface. The subsequent removal of carbonaceous templates via calcination in air results in the formation of 2D mSnO2 due to the confinement effect of the templates. Pd nanoparticles are controllably deposited on the surface of 2D mSnO2 via in situ reduction, forming ultrathin 2D Pd/mSnO2 nanocomposites with thicknesses of 6-8 nm. Owing to the unique 2D mesoporous structure with rich oxygen defects and highly exposed metal-metal oxide interfaces, 2D Pd/mSnO2 exhibits excellent sensing performance toward acetone with high sensitivity, a short response time, and good selectivity under low working temperature (100 °C). This fast and convenient microexplosion synthesis strategy opens up the possibility of constructing 2D porous functional materials for various applications including high-performance gas sensors.
ABSTRACT
A sustainable photocatalyst of Ti3+ self-doped elongated anatase nanowires combined with reduced graphene oxide (TiO2 NWs@rGO) was prepared via a facile one-step reductive synthesis process using NaBH4 as reductant for the first time. The obtained optimal TiO2 NWs@rGO composite has a large surface area,182â¯m2 â¯g-1, which demonstrates strong adsorption capacity due to the multilayered structure built by highly crystallized nanowires of TiO2 and ultrathin rGO layers. When the photocatalyst was applied in removing waste engine oil (100â¯mL, 50â¯mgâ¯L-1), it exhibited outstanding performance with up to COD 98.6% removal extent (from 145 initial to 2â¯mgâ¯L-1 final COD) after 5â¯h, which is 34.1% higher than that of TiO2 NWs (64.5% COD removal extent). Gas chromatography-mass spectrometry analyses of residual waste engine oil after photocatalysis shows significant reductions of C6-C19 chemicals as well as total disappear of C15,C16, C17, C18 chemicals. The outstanding photocatalytic activity of TiO2 NWs@rGO benefits from sensitive response to visible light, improved surface reactivity and high electron flux enabled by rGO and Ti3+ in TiO2. In addition, this composite catalyst can be self-cleaned, and recycled for reuse, which suggests promising potential for waste engine oil treatment.
ABSTRACT
This work shows that mesoporous polymeric films with spherical and elliptical pores can be obtained by in situ structure inversion of the azo polymer colloid arrays through selective interaction with solvent. The epoxy-based azo polymer contained both the pseudo-stilbene-type azo chromophores and the hydrophilic carboxyl groups. The colloidal spheres of the azo polymer were prepared by gradual hydrophobic aggregation of the polymeric chains in THF-H2O media, induced by a steady increase in the water content. Ordered 2D arrays of the hexagonally close-packed colloidal spheres were obtained by the vertical deposition method. After the solvent (THF) annealing, the ordered 2D arrays were directly transformed to mesoporous films through the sphere-pore inversion. Under the same condition, the 2D arrays composed of the ellipsoidal colloids, which were obtained by the irradiation of a polarized Ar+ laser beam on the colloidal sphere arrays, could be transformed to films with ordered elliptical pores. To our knowledge, this is the first example to demonstrate that mesoporous structures can be directly formed from the colloidal arrays of a homopolymer through structure inversion. This observation can shed new light on the nature of self-assembly processes and provide a feasible approach to fabricate mesoporous structures without the infiltration-removal step. By exploring the photoresponsive properties of the materials, mesoporous film with special pore structure and properties can be expected.
ABSTRACT
This work shows that a linearly polarized Ar+ laser single-beam irradiation can cause stretching deformation of azo polymer colloidal spheres along the polarization direction of the laser beam. An epoxy-based polymer, containing 4-amino-4'-carboxyazobenzene at each repeat unit, was used to construct the colloidal spheres. The colloidal spheres were prepared by gradual hydrophobic aggregation of the polymeric chains in a THF/H2O dispersion medium, which was induced by a steady increase in the water content. When the obtained colloidal spheres were exposed to the spatially filtered and collimated Ar+ laser beam (488 nm, 150 mW/cm2), the colloids were stretched along the polarization direction of the laser beam. In the testing period (20 min), the colloids were deformed continuously as the irradiation time increased. When 2D close-packed arrays of the colloidal spheres were irradiated by the polarized laser single-beam, the colloidal spheres were all uniformly stretched along the polarization direction of the laser beam. On the contrary, when the arrays were irradiated by the interfering p-polarized laser beams, only the colloidal spheres in the bright regions of the interference pattern were significantly deformed.
ABSTRACT
In this work, azobenzene-containing colloidal spheres have been fabricated and used to construct photoresponsive monolayers. The colloidal spheres were prepared from an amphiphilic azobenzene-containing random copolymer through hydrophobic aggregation of the polymer chains, which was induced by adding the selective solvent (H2O) into a THF solution of the polymer. The size and size distribution of the spheres depended on the initial concentration of the azo polymer in THF and the H2O/THF ratio. Adjusting those factors and optimizing other preparation conditions, uniform colloidal spheres could be obtained. Monolayers composed of hexagonally close-packed colloidal spheres were prepared by the capillary-force-driven method. The colloidal monolayers showed obvious dichroism after laser irradiation due to the photoinduced azo-chromophore orientation occurred in the spheres. The orientation order parameter was related to the irradiation time and estimated to be 0.09 at the photostationary state. The colloidal spheres and their monolayers can potentially be used as building blocks or media for reversible optical data storage, photo-switching, sensors, and other photo-driven devices.
ABSTRACT
Photoinduced shape deformation of colloidal spheres made of an amphiphilic azo polymer has been demonstrated in this work. The polymer contains the donor-and-acceptor-type azobenzene chromophores and can form uniform colloidal spheres by dropwise adding water into its THF solution. When the colloidal spheres obtained were exposed to the interfering p-polarized Ar+ laser beams (150 mW/cm2), the colloidal spheres changed to prolates (i.e., "rugby-balls"), "spindles", and finally "rods", depending on the irradiation times. The elongated direction of the spheres was observed to be the same as the polarization direction of the laser beam. The average major-to-minor ratio of the ellipsoids could be easily adjusted by controlling the irradiation time. The deformation effect observed in this work can offer a new way to prepare nonspherical colloids from colloidal spheres and will shed new light on the correlation between the photodriven shape deformation and photoinduced surface relief gratings for the same type of polymers.