ABSTRACT
BACKGROUND: Dental implantology's success relies on adequate bone volume and quality, necessitating bone augmentation for implant placement. Primary lateral bone augmentation, utilizing autogenous block grafts, addresses horizontal bone loss. OBJECTIVE: This study aims to evaluate the efficacy of autogenous block grafting, specifically ramus and fibula blocks, in addressing severe atrophic ridges before and after implant placement. METHODS: Twenty-one patients underwent block grafting, predominantly using the ramus technique (80/20 ratio). CBCT measurements assessed horizontal grafting outcomes. Implant success and bone volume changes were analyzed. RESULTS: Post-grafting, bone width increased from 1.8-3.1 mm to 4.5-6 mm, exceeding critical thresholds. Implant success reached 95%, indicating the grafting techniques' effectiveness. CONCLUSION: Autogenous block grafting, especially with ramus and fibula blocks, transforms severe atrophic ridges, enabling successful implant integration. Long-term follow-up is essential for a comprehensive evaluation. CLINICAL RELEVANCE: This study provides crucial insights into autogenous block grafting's transformative impact on challenging cases, guiding future applications in reconstructive dentistry.
ABSTRACT
INTRODUCTION: Over the years, implant therapy has been a commonly used treatment option for individuals who are partially or totally edentulous, with a long-term success rate of over 90%. With significant advancements in biomaterials and technology, implant dentistry can now conduct prosthetic rehabilitations in the majority of patients catering to all types of needs. However, in order to meet the demands of a patient base that is always growing, new trends in implantology are emerging in recent years that are focused on minimally invasive surgery and financial sustainability. In certain clinical scenarios, connecting teeth and implants to support fixed partial prosthesis (FPPs) may be a predictable and workable course of treatment. MATERIALS AND METHODS: 22 patients were selected for this study who had tooth and implant supported prosthesis placed as a final restoration. Out of these 22 patients; 12 were male and 10 were female patients. Implants were placed following proper protocol and if grafting procedures were required they were carried out. A second stage surgical procedure was carried out and delayed loading protocols were followed. The statistical analysis was done using the IBM SPSS 24.0, Chicago, USA. The survival of the implants and teeth were measured by the Kaplan Meier survival scale. Bone loss was assessed at baseline(upon loading), 12 months and 24 months. RESULTS: The implant survival rate was measured at 6 months, 12 months, 18 months and 24 months. At 24 months, one implant showed failure, so the survival rate of the implants were 95.4%. Bone loss of 1 mm was seen around one implant at 12 months. Bone loss of 1 and 2 mm was present around two implants and one implant respectively at 24 months. CONCLUSION: From the results of this study, we can conclude that tooth implant supported prosthesis show very good survival when used in rehabilitation cases.
Subject(s)
Alveolar Bone Loss , Dental Implants , Immediate Dental Implant Loading , Humans , Male , Female , Dental Implants/adverse effects , Follow-Up Studies , Dental Implantation, Endosseous/methods , Dental Implantation , Dental Prosthesis, Implant-Supported , Dental Restoration Failure , Treatment Outcome , Dental Prosthesis Design , Alveolar Bone Loss/etiologyABSTRACT
INTRODUCTION: The prevalence of adults with partially dental arches is expected to be more than imagined and patients requiring replacement of missing teeth are slowly increasing in number too. Removable partial dentures are known to provide for substantial replacement for the missing teeth with also added advantages when compared to fixed or implant prosthesis, mainly in elderly patients. Denture base material performance and durability are greatly influenced by wettability and water contact angle. In the case of dentures; adequate moisture distribution is necessary to ensure excellent wettability which has an influence on comfort and oral health. The purpose of conducting this study was to find out whether the advancements made using PEEK (Polyether ether ketone) would prove to be more beneficial than the current upgrades in the current material spectrum. MATERIALS AND METHODS: This study was performed under in vitro conditions. All the fabrication and processing was done only by one operator. The materials used were divided into three groups each comprising 20 samples. Group A was modified polymethylmethacrylate (Bredent Polyan), Group B was polyoxymethylene acetal resin (Biodentaplast) and Group C was PEEK. An Ossila Goniometer was used to measure the contact angle. The three types of liquids used for the testing included distilled water, natural saliva and mouth wetting solution (Wet Mouth Liquid, ICPA India). Human saliva was collected from an individual with no medical conditions and normal salivary secretion. RESULTS: The data was analyzed using One-way ANOVA test and a pairwise comparison using the Post Hoc Tukey's Honest Significant Difference. Table 1 consists of the mean water contact angles of the denture base materials and mean contact angles of various denture base materials. In saliva, mouth wetting solution and distilled water, the highest mean and least mean contact angle was seen in Polyan and Biodentaplast respectively. A signicant difference was seen between PEEK and Polyan and Biodentaplast and Polyan on further comparison. CONCLUSION: From the resources and the materials at our disposal, it could be concluded that Polyan, Biodentaplast and PEEK and could be used as viable options in cast partial denture framework.