Measurement of atmospheric amines and aminoamides by column adsorption/extraction and hydrophilic liquid chromatography-electrospray-tandem mass spectrometry.

Sampling and chromatography-mass spectrometry methods were investigated to measure atmospheric amines and aminoamides. Amines and their amide derivatives play significant roles in new particle formation (NPF) in the atmosphere, especially diamines and aminoamides have higher NPF potentials compared to monoamines. For amine sampling, silica gel tube collection and formic acid extraction gave good overall recoveries (>93 ± 8%) for mono-, di-, tri-, tetramines, and aminoamides. Two chromatography methods were subjected to analyze the extracted amines. One involved direct analysis using hydrophilic interaction liquid chromatography with carboxyl or diol group functioned separation column (carboxyl-HILIC or diol-HILIC), and the other utilized derivatization with 4-(N,N-dimethylaminosulfonyl)-7-fluoro-2,1,3-benzoxadiazole (DBD-F) and subsequent reversed-phase chromatography (HPLC). Separated amines were detected by electrospray ionization and tandem mass spectrometry in both cases. DBD-F-HPLC method provided good sensitivity for mono- and all polyamines (limit of detection (LOD) < 4.6 nM, relative standard deviation (RSD) for 100 nM < 9.2%). However, aminoamides could not be detected by DBD-F-HPLC. Carboxyl-HILIC provided good sensitivities for mono- and diamines and aminoamides (LOD < 1.6 nM, RSD < 4.8%). Forest air measurement was performed and data obtained by carboxyl-HILIC and DBD-F-HPLC showed good agreement for 1,3-diaminopropane, 1,4-diaminobutane (putrescine) and 1,5-diaminopentane (cadaverine) (R2 = 0.9215-0.9739, n = 7-14). Carboxyl-HILIC method was the best for the amine analysis, and combination with silica gel tube sampling provides atmospheric monitoring available. The developed method can be used not only to study atmospheric chemistry of diamines and aminoamides but also to analyze flavor/odor of foods, flowers and wastes.

Two-step extraction for the evaluation of metal-organic framework impregnated materials.

Metal-organic frameworks (MOFs) are widely used for gas adsorption, separation, and sensing materials. In most cases, MOFs are not used in their crystal form but as impregnated materials because the fine crystals result in high-pressure drops. One key characteristic of MOF-impregnated materials is the amount of MOF in the material. This is evaluated using the wet digestion method; however, it is limited to determining only the metal content. Moreover, some metal, denoted as free metal, will not react with ligands to form MOFs. Additionally, it is crucial to determine the ligand amount, which cannot be determined using wet digestion. In the present study, a two-step extraction method for copper (II) benzene-1,3,5-tricarboxylate (Cu-BTC MOF) impregnated materials was developed to determine the MOF formed and free metals and ligands. Various solvents were applied to evaluate the extraction efficiencies. The results led to the selection of ethanol (EtOH) for extracting free Cu2+ and BTC, while 0.3 M HNO3 was chosen to extract MOF-formed Cu2+ and BTC. The MOF-impregnated sample material was first extracted using EtOH and then 0.3 M HNO3. The Cu2+ and BTC in the obtained extract solutions, as well as EtOH and HNO3, were analyzed using flame atomic absorption spectroscopy and high-performance liquid chromatography, respectively. In standard addition tests, free and MOF-formed Cu2+ and BTC were quantitatively extracted from MOF-impregnated materials. The developed two-step analysis method was successfully applied to Cu-BTC-impregnated materials used in gas sensing.

Real-world prostate-specific antigen response and progression to castration-resistant prostate cancer among men with metastatic castration-sensitive prostate cancer treated with apalutamide: a multi-institutional study in the Chu-shikoku Japan Urological Consortium.

BACKGROUND: Japanese men receiving apalutamide often experience skin-adverse events (AEs), possibly requiring treatment interruption or dose reduction. However, concerns have arisen regarding the impact of these adjustments on the efficacy of apalutamide. Our study evaluated the efficacy, safety, and persistence of apalutamide in men with metastatic castration-sensitive prostate cancer (mCSPC). METHODS: We retrospectively reviewed the medical records of 108 men with mCSPC from 14 Japanese institutions. The primary outcomes were the efficacy of apalutamide: prostate-specific antigen (PSA) response (50%, 90% and < 0.2 decline) and progression to castration-resistant prostate cancer (CRPC). The secondary outcomes were the skin-AE and compliance of apalutamide. RESULTS: PSA50%, PSA90% and PSA < 0.2 declines were observed in 89.8, 84.3 and 65.7%, and the median time to CRPC progression was not reached. PSA < 0.2 decline and an initial full dose of apalutamide were significantly associated with a longer time to CRPC. The most common AE was skin-AE (50.9%), and there was no association between the occurrence of skin-AE and the time to CRPC (P = 0.72). The median apalutamide persistence was 29 months, which was longer in the initial full dose recipients than in the reduced dose recipients. The dosage is reduced in about 60% of patients within the first year of treatment in the initial full dose recipients. CONCLUSIONS: Our findings indicate the effectiveness of apalutamide in Japanese men with mCSPC, despite a substantial portion requiring dose reduction within a year among the initial full dose recipients.

Abundant production of dimethylsulfoniopropionate as a cryoprotectant by freshwater phytoplanktonic dinoflagellates in ice-covered Lake Baikal.

Phytoplanktonic dinoflagellates form colonies between vertical ice crystals during the ice-melting season in Lake Baikal, but how the plankton survive the freezing conditions is not known. Here we show that the phytoplankton produces large amounts of dimethylsulfoniopropionate (DMSP), which is best-known as a marine compound. Lake-water DMSP concentrations in the spring season are comparable with those in the oceans, and colony water in ice exhibits extremely high concentrations. DMSP concentration of surface water correlates with plankton density and reaches a maximum in mid-April, with temperature-dependent fluctuations. DMSP is released from plankton cells into water in warm days. DMSP is a characteristic osmolyte of marine algae; our results demonstrate that freshwater plankton, Gymnodinium baicalense, has DMSP-producing ability, and efficiently uses the limited sulfur resource (only 1/500 of sea sulfate) to survive in freshwater ice. Plankton in Lake Baikal do not need an osmolyte, and our results clearly indicate that DMSP plays a cryoprotective role. DMSP, although a characteristic marine compound, could also be an important zwitterion for algae of other boreal lakes, alpine snow, and glaciers.

Summary of the clinical practice manual for late-onset hypogonadism.

Testosterone plays an important role in maintaining both physical and mental function. Age-related testosterone depletion contributes to the development of angina, arteriosclerosis, obesity, metabolic syndrome, dementia, frailty, and a range of other conditions. A condition involving age-related testosterone depletion and the associated clinical symptoms is defined as late-onset hypogonadism (LOH). LOH is treated by testosterone replacement therapy. Indications for testosterone replacement therapy are determined by evaluating symptoms and signs.

Radioactive isotope separation with 3D-printed flow-based device.

Radioactive isotope (RI) metals are a new type of tracer for positron emission tomography generated from the target metal by proton irradiation using a cyclotron. The generated metal RIs need to be separated from the target metal rapidly and effectively. In the present study, we developed a 3D-printed flow device to separate metal RIs from target metals. The separation was performed with selective formation of ethylenediaminetetraacetic acid (EDTA) complex based on the difference in formation constants. The RI metal selectively formed a EDTA complex, thus changing its ionic charge in solution. The solution was then introduced into a cation exchange column for selective adsorption of the target metal. The solution with added chelator and controlled pH was introduced into the developed system and automatically separated metal RI from target metals within 14 min. The separation method was applied to separate RI 67Ga from target metal Zn using a mixture of 107 pg L-1 67Ga in 250 mg L-1 Zn2+. The recoveries of 67Ga and Zn were 97% and 100%, respectively. Furthermore, an ultraviolet (UV) radiation reactor was integrated into the system to decompose the EDTA complex and recover the Ga3+ ion. Ga3+ recovery by UV radiation was effective, 87%. The developed system was also successfully applied to the separation of Zr and Y. Therefore, the method and system can be applied to separate other metal RIs from target metals.

A concise synthesis of thioaurones via NBS-induced cyclization of MOM-protected 2'-mercaptochalcones.

A mild and efficient approach for the synthesis of thioaurones via NBS-induced cyclization of methoxymethyl-protected mercapto-chalcones has been developed. This simple method is highly functional group tolerant and provides straightforward access to thioaurones in good to high yields.

The Urinary Bladder is Rich in Glycosphingolipids Composed of Phytoceramides.

Glycosphingolipids (GSLs) are composed of a polar glycan chain and a hydrophobic tail known as ceramide. Together with variation in the glycan chain, ceramides exhibit tissue-specific structural variation in the long-chain base (LCB) and N-acyl chain moieties in terms of carbon chain length, degree of desaturation, and hydroxylation. Here, we report the structural variation in GSLs in the urinary bladders of mice and humans. Using TLC, we showed that the major GSLs are hexosylceramide, lactosylceramide, globotriaosylceramide, globotetraosylceramide, Neu5Ac-Gal-Glc-Ceramide, and Neu5Ac-Neu5Ac-Gal-Glc-Ceramide. Our LC-MS analysis indicated that phytoceramide structures with a 20-carbon LCB (4-hydroxyeicosasphinganine) and 2-hydroxy fatty acids are abundant in hexosylceramide and Neu5Ac-Gal-Glc-Ceramide in mice and humans. In addition, quantitative PCR demonstrated that DES2 and FA2H, which are responsible for the generation of 4-hydroxysphinganine and 2-hydroxy fatty acid, respectively, and SPTLC3 and SPTSSB, which are responsible for the generation of 20-carbon LCBs, showed significant expressions in the epithelial layer than in the subepithelial layer. Immunohistochemically, dihydroceramide:sphinganine C4-hydroxylase (DES2) was expressed exclusively in urothelial cells of the urinary bladder. Our findings suggest that these ceramide structures have an impact on membrane properties of the stretching and shrinking in transitional urothelial cells.

Electrodialytic Universal Synthesis of Highly Pure and Mixed Ionic Liquids.

Ionic liquids (ILs) have attracted significant attention from researchers in various fields as a result of their unique properties. As new and important applications are identified for these materials, there is also a drive to develop methods for accessing a wider range of ILs. However, despite this demand, only a few techniques have so far been reported and, more importantly, general but efficient processes for IL synthesis have been lacking. Thus, it would be beneficial to devise a cost-effective, environmentally friendly means of producing a wide variety of pure ILs. The present work demonstrates a general purpose electrodialysis approach to the formation of highly pure ILs, based on the formation of nine different ILs from various combinations of cations and anions. In each case, the IL is obtained with a purity of greater than 99%. This method offers the advantages of avoiding the use of hazardous organic solvents and eliminating tedious and costly purification processes. Unlike conventional methods, this membrane-based technology also prevents the generation of side products. Mixed ILs have many potential applications, and the present technique readily generates various mixed ILs based on a simple adjustment of the applied current.

Highly Efficient Separation of Ultratrace Radioactive Copper Using a Flow Electrolysis Cell.

Preparing compounds containing the radioisotope 64Cu for use in positron emission tomography cancer diagnostics is an ongoing area of research. In this study, a highly efficient separation method to recover 64Cu generated by irradiating the target 64Ni with a proton beam was developed by employing a flow electrolysis cell (FE). This system consists of (1) applying a reduction potential for the selective adsorption of 64Cu from the target solution when dissolved in HCl and (2) recovering the 64Cu deposited onto the carbon working electrode by desorbing it from the FE during elution with 10 mmol/L HNO3, which applies an oxidation potential. The 64Cu was selectively eluted at approximately 30 min under a flow rate of 0.5 mL/min from the injection to recovery. The newly developed flow electrolysis system can separate the femtomolar level of ultratrace radioisotopes from the larger amount of target metals as an alternative to conventional column chromatography.

Real-world analysis of apalutamide-associated skin adverse events in Japanese patients with advanced prostate cancer: a multi-institutional study in the Chu-shikoku Japan Urological Consortium.

BACKGROUND: Apalutamide-associated skin adverse events are more common in the Japanese than in the global population. However, limited clinical data have hampered further understanding. This real-world study investigated the clinical characteristics of skin adverse events in patients with advanced prostate cancer. METHODS: We retrospectively reviewed 119 patient records from 16 institutions in Japan. Skin adverse events were graded according to the Common Terminology Criteria for Adverse Events (v5.0). The incidence and characteristics of skin adverse events (along with the clinical risk factors for their incidence, worsening, and recurrence) were evaluated. RESULTS: Fifty-five patients (46.2%) experienced skin adverse events. The median times to the incidence and remission of skin adverse events were 62 and 30 days, respectively. Grade 3 skin adverse events were observed in 15 patients (12.6%). The median time from the first incidence to apalutamide interruption was significantly longer in patients with progression to grade 3 skin adverse events than in those without such a progression (8 vs. 0 days, p = 0.005). Skin adverse events were observed in 45.2% of patients who resumed apalutamide treatment (median treatment interruption time: 31.5 days). Sixteen patients (13.4%) permanently discontinued apalutamide due to skin adverse events. No significant clinical risk factors for the incidence, worsening and recurrence of apalutamide-associated skin adverse events were observed. CONCLUSIONS: Nearly half of the Japanese patients in this study experienced skin adverse events following apalutamide administration. The time to apalutamide discontinuation after the incidence of skin adverse events was positively correlated with the worsening of these events.

Electrodialytic Enrichment and Matrix Conversion for the Determination of Trace Metals in Ultra-Pure Water.

The presence of trace contaminants in ultra-pure water (UPW) used in fabrication process can greatly affect the yield and quality of industrial products. In the present study, the electrodialytic enrichment of metal cations as a means of continuously monitoring the UPW quality was studied. A newly designed electrodialytic enrichment device (EED) was used to quantitatively transfer metal ions from samples to dilute nitric acid, which was then directly introduced into an inductively coupled plasma-mass spectrometry (ICP-MS) instrument. This process could be performed without contamination of the sample, and the enrichment factor was solely dependent on the flow rate ratio of the sample and acceptor solutions. The transference of analytes into the acidic solution improved the responsivity of the ICP-MS analysis, especially at low concentrations of less than 1 µg/L. Blank solutions to support the analysis of UPW could be produced using the EED effluent, from which metal ions were quantitatively removed. In addition, calibration curves with concentration ranges of several nanograms per liter were obtained by preparing standards using a dynamic gravimetric method while employing a single bottle and continuous mass monitoring to avoid any contamination from the volumetric flasks. The sensitivities associated with the ICP-MS analysis of a number of trace metal ions were improved by one or two orders of magnitude. The data show that the present EED is able to continuously produce enriched analyte solutions to allow the ongoing monitoring of UPW quality.

An in vitro system for experimentally induced cryptorchidism.

Cryptorchidism is one of the most common abnormalities of male sexual development, and is characterized by the failure of the testis to descend into the scrotum. Despite extensive studies of cryptorchidism over the past century, the mechanisms for temperature-induced germ-cell loss are not well understood. All of the main cell types in the testis are believed to be affected by the elevated testis temperature induced by cryptorchidism. The cooler temperature in the special environment of the scrotum is required for maintaining optional conditions for normal spermatogenesis. Many studies reported that experimentally induced cryptorchidism caused germ cell apoptosis and suppressed spermatogenesis. However, other factors including hormones must also be examined for cryptorchidism. To explore the mechanism for cryptorchidism, in vitro cultures of testes have been used, but complete spermatogenesis using in vitro methods was not accomplished until 2011. In 2011, Sato et al. (Nature, 471, 504-507) reported the in vitro production of functional sperm in cultured neonatal mouse testes. Using this in vitro system, for the first time, we report that spermatogenesis was abrogated at 37 °C, in accordance with in vivo surgery-mediated cryptorchidism, while spermatogenesis proceeded at 34 °C in cultured testes. This result clearly showed that temperature is the sole determinant of cryptorchidism. Moreover, we found that spermatogenesis was arrested before early spermatocytes at 37 °C. In conclusion, using our in vitro system, we have demonstrated that (1) temperature is the determining factor for cryptorchidism, and (2) higher temperature (37 °C) suppresses DNA synthesis in spermatogenesis.

Rapid Flow-Based System for Separation of Radioactive Metals by Selective Complex Formation.

Short-lived radioactive metals are important tracers in clinical diagnosis. Radioactive metals for clinical use are produced from suitable target metals in cyclotrons. The trace amount of radioactive metal produced is contained in a relatively large amount of target metal. A rapid and effective method is required to isolate the radioactive metal. In the present study, selective complex formation followed by cation-exchange adsorption was performed in a continuous flow-based system. Ethylenediamine-N,N,N',N'-tetraacetic acid (EDTA) was selected as the ligand after simulation of the separation of radioactive Ga from the target (Zn). Selectively, the Ga-EDTA complex passed through the cation trap, while Zn2+ was trapped. This separation principle is opposite to that of typical solid-phase extraction, which captures the target ion. The proposed separation was performed in a flow-based system with a parallel, open-channel ion trap. The performance was optimized by altering the channel dimensions, channel-filling mesh, and flow rate. Finally, the target radioactive metal, Ga, was selectively and effectively (>99%) separated from a mixture of 50 fg Ga/L and 100 mg Zn/L. The concentration of Zn remaining in the Ga solution was 2.3 µg/L. The complexed Ga was converted to free Ga3+ by a simple UV irradiation method. The proposed method effectively and rapidly separates trace amounts of radioactive metals contained in larger amounts of target metals using a simple flow system that can be operated on site.

Indirect Potentiometric pH Detection of Weak Acids with Absolute Quantitation by a Theoretical Approach.

A fast response potentiometric flow-through pH sensor was applied for organic acid determination. The analyte response with the pH sensor was obtained by eluent pH modification following ion exclusion chromatography with HClO4 as an eluent. The response characteristics depend on the adjusted baseline pH. The baseline pH adjustment was successfully done with an ammonia permeation device without solution mixing, which may cause analyte dilution, dispersion, and mixing noise. After pH adjustment, the pH response was universal to the equivalent of introduced analyte acids because the pH response was obtained by the titration of the permeant ammonia by the analytes. The average of limit of detections (S/N = 3) was 0.06 mM for seven target organic acids. Furthermore, the pH response follows the theoretical pH calculation with the concentrations of the eluent, pH modifier, and analyte. Thus, the analyte concentration in the sample can be theoretically calculated from the pH response without calibration by the analyte standard. Predicted concentrations of injected standards were within 5% of the actual standard concentration. Additionally, analysis of real samples was performed and compared with the conventional post-column reaction with a bromothymol blue (BTB) method. The results obtained with the present system (absolute quantification with theoretical calculation) and conventional BTB method agreed within 10% of errors.

Natural dimethyl sulfide gradients would lead marine predators to higher prey biomass.

Finding prey is essential to survival, with marine predators hypothesised to track chemicals such as dimethyl sulfide (DMS) while foraging. Many predators are attracted to artificially released DMS, and laboratory experiments have shown that zooplankton grazing on phytoplankton accelerates DMS release. However, whether natural DMS concentrations are useful for predators and correlated to areas of high prey biomass remains a fundamental knowledge gap. Here, we used concurrent hydroacoustic surveys and in situ DMS measurements to present evidence that zooplankton biomass is spatially correlated to natural DMS concentration in air and seawater. Using agent simulations, we also show that following gradients of DMS would lead zooplankton predators to areas of higher prey biomass than swimming randomly. Further understanding of the conditions and scales over which these gradients occur, and how they are used by predators, is essential to predicting the impact of future changes in the ocean on predator foraging success.

Measurement Device for Ambient Carbonyl Sulfide by Means of Catalytic Reduction Followed by Wet Scrubbing/Fluorescence Detection.

A portable chemical analysis system for monitoring ambient carbonyl sulfide (COS) was investigated for the first time. COS is paid attention to from the perspectives of photosynthesis tracer, breath diagnosis marker, and new process-use in the manufacture of semiconductors. Recently, the threshold level value of COS was settled at 5 ppm in volume ratio (ppmv) for workplace safety management. In this work, COS was converted to H2S by a small column packed with alumina catalyzer at 65 °C. Then, the H2S produced was collected in a small channel scrubber to react with fluorescein mercuric acetate (FMA), and the resulting fluorescence quenching was monitored using an LED/photodiode-based miniature detector. The miniature channel scrubber was re-examined to determine its robustness and easy fabrication, and conditions of the catalyzer were optimized. When the FMA concentration used was 1 µM, the limit of detection and dynamic range, which were both proportional to the FMA concentration, were 0.07 and 25 ppbv, respectively. Ambient COS in the background level and even contaminated COS in the nitrogen gas cylinder could be detected. If necessary, H2S was removed selectively by reproducible adsorbent columns. COS concentrations of engine exhaust were measured by the proposed method and by cryo-trap-gas chromatography-flame photometric detection, and the results obtained (0.5-5.9 ppbv) by the two methods agreed well (R 2 = 0.945, n = 19). COS in ambient air and exhaust gases was successfully measured without any batchwise pretreatment.

Electrodialytic Handling of Radioactive Metal Ions for Preparation of Tracer Reagents.

Radioactive metals are applied in biochemistry, medical diagnosis such as positron emission tomography (PET), and cancer therapy. However, the activity of radioisotopes exponentially decreases with time; therefore, rapid and reliable probe preparation methods are strongly recommended. In the present study, electrodialytic radioactive metal ion handling is studied for counter ion conversion and in-line probe synthesis. Presently, counter ion conversion and probe synthesis are achieved by evaporative dryness and solution mixing, respectively. Evaporative dryness is time-consuming and is a possible process that can lead to loss of radioactive metal ions. Mixing of solutions for synthesis makes dilution and undesirable effects of counter ion on the synthesis. An optimized electrodialytic flow device can transfer a radioisotope, 64Cu2+, with high recovery from HCl matrices to HNO3 (∼100%). Matrices can also be transferred into acetic acid and citric acid, even though the concentration of the metal ion is at the picomolar level. The ion transfer can also be achieved with simultaneous counter ion conversion, complex synthesis, and enrichment. When the ligand was dissolved in an acceptor solution, the transferred metal ions from the donor were well mixed and formed a complex with the ligand in-line. The efficiency of the synthesis was ∼100% for 1.0 pM 64Cu. A relatively larger donor-to-acceptor flow rate can enrich the metal ion in the acceptor solution continuously. The flow rate ratio of 10 (donor/acceptor) can achieve 10 times enrichment. The present electrodialytic ion handling method can treat ultra-trace radioisotopes in a closed system. With this method, rapid, effective, and safe radioisotope treatments were achieved.

Determination of oxoanions and water-soluble species of arsenic, selenium, antimony, vanadium, and chromium eluted in water from airborne fine particles (PM2.5): effect of acid and transition metal content of particles on heavy metal elution.

Heavy metals in particulate matter (PM) are of great concern, and their effects on the environment and human health depend on their solubilities and species present. In this study, the solubility of As, Se, Sb, V and Cr and their species eluted in water was investigated. As, Se, Sb, and V were present mostly in fine particles, and they were predominantly water-soluble in fine particles (<2.5 µm, PM2.5) but insoluble in coarse particles (>2.5 µm). Solubility of Cr was poor even in fine particles. It was found that for fine particles, solubilities of the heavy metals were related to the nitrate and sulfate contents. This suggests that the higher the acidity of the particles, the higher the solubility of the heavy metals. Oxoanions of the five kinds of heavy metals in water extracts of fine particles were determined by inductively coupled plasma mass spectrometry preceded by ion chromatography. The results suggested the presence of atmospheric oxidation during the aerosol transportation. Also, the As(iii)/As(v) (arsenite/arsenate) ratios for the fine particle extracts were related to the transition metal concentrations, which indicated that Fe, Cu, etc. in fine particles affected the As redox equilibrium. It was suggested that the heavy metals exist as complexes with iron hydroxide and dissolved organic matter in addition to the free oxoanions. These investigations were performed for PM samples collected in winter and summer in Kumamoto, west Japan, where the site is strongly exposed to westerly winds from continental East Asia. The obtained results improve our understanding of the behavior of the heavy metals in airborne PM after depositing on a wet environment and biota.

Miniaturized crossflow ion transfer device for post-column enrichment in ion chromatography.

The sensitivity of an ion chromatography system was improved using electrodialytic post-column enrichment. Even though post-column reactions, such as suppression, have been used to enhance the sensitivity, there are only a few methods available to increase the concentration and improve the sensitivity. Post-column in-line enrichment was achieved with a miniaturized crossflow ion transfer device (ITD) prepared in our laboratory. In the crossflow ITD, separated ionic solutes in the suppressed eluent were transferred into the acceptor solution (in-line purified ultrapure water), which had a flow rate less than that of the eluent. Because of highly efficient ion transfer, the analytes were enriched in the acceptor solution and the enrichment factor was depending on flow rate ratio of acceptor to eluent. Furthermore, the crossflow ITD minimized peak dispersion in the channel. The limit of detection improved by 5.0 ± 0.3 times when the flow rate ratio was 10.