ABSTRACT
Background: To evaluate the thermal insulation of protective liners and glass ionomer cement during light-curing procedures. Material and Methods: Human third molars underwent Class I preparations with dimensions 5 mm long × 4 mm wide × 4 mm deep in a standardized manner ensured a consistent ±0.5 mm dentin thickness at the pulpal floor. The teeth were attached to a customized oral cavity chamber simulator with a circulating bath at a standardized temperature of 34.2 ± 1oC. The temperature variations at the pulpal floor were captured in real-time by video using an infrared thermal camera (FLIR ONE Pro, FLIR Systems). The materials evaluated were: Dycal (Dentsply), TheraCal LC (Bisco), Activa (Pulpdent), and Fuji II LC (GC). All light-activation procedures were performed with the same light-curing unit (Valo Grand, Ultradent) in standard mode, 1000 mW/cm2, and time of exposure following manufacturer instructions. A power analysis was conducted to determine the sample size considering a minimal power of 0.8, with α=0.05. Statistical analyses were performed using ANOVA and Tukey's test for multiple comparisons. Results: The temperature at the pulpal floor increased above the 5.5 ºC safety threshold difference for clinical scenarios tested. None of the materials provided proper thermal insulation for light-curing procedures (p = 0.25). The higher the number of light-cured steps, the longer the pulp remained above the 5.5 ºC temperature threshold. Conclusions: The materials tested provided improper thermal insulation (Δ > 5.5 ºC). Thus, prolonged or multiple light-curing exposures can be harmful to the pulp tissues. Therefore, for indirect pulpal capping procedures, self-cured materials or a reduced number of steps requiring light curing must be adopted to reduce the amount of time the pulp remains above the 5.5 ºC safety temperature threshold. Key words:Dental Pulp Capping, Calcium hydroxide, Bioactive, Thermal Damage.
ABSTRACT
The present study examined different concentrations of the butylated hydroxytoluene (BHT) inhibitor on the kinetics of conversion, polymerization shrinkage stress, and other correlated physicochemical properties of experimental resin composites (ERC). A model composite was formulated with 75 wt% filler containing 0.5 wt% camphorquinone and 1 wt% amine with BHT concentrations of 0.01 wt% (BHT-0.01); 0.1 wt% (BHT-0.1); 0.25 wt% (BHT-0.25); 0.5 wt% (BHT-0.5); 1 wt% (BHT-1), and control (no BHT). They were tested on polymerization shrinkage stress (PSS; n = 5), degree of conversion (DC; n = 3), maximum polymerization rate (RpMAX; n = 5), water sorption (Wsp; n = 0), and solubility (Wsl; n = 10), flexural strength (FS; n = 10), flexural modulus (FM; n = 10), Knoop microhardness (KH; n = 10), and microhardness reduction (HR; n = 10). Data concerning these tests were submitted to one-way ANOVA and Tukey's test (α = 0.05; ß = 0.2). BHT-0.25, BHT-0.5, and BHT-1 showed a gradually significant decrease in PSS (p = 0.037); however, BHT-1 demonstrated a decrease in the physicochemical properties tested. Thus, within the limitations of this study, it was possible to conclude that BHT concentrations between 0.25 and 0.5 wt% are optimal for reducing shrinkage stress without affecting other physicochemical properties of ERCs.
Subject(s)
Butylated Hydroxytoluene , Composite Resins , Materials Testing , Polymerization , Stress, Mechanical , Butylated Hydroxytoluene/chemistry , Composite Resins/chemistry , Chemical Phenomena , Solubility , Water/chemistry , HardnessABSTRACT
This study aimed to evaluate the effect of an elastomeric urethane monomer (Exothane-24) in different concentrations on physicochemical properties, gap formation, and polymerization shrinkage stress of experimental resin composites. All experimental composites were prepared with 50 wt.% of Bis-GMA and 50 wt.% of TEGDMA, to which 0 wt.% (control), 10 wt.%, 20 wt.%, 30 wt.%, and 40 wt.% of Exothane-24 were added. Filler particles (65 wt.%) were then added to these resin matrixes. Ultimate tensile strength (UTS: n = 10), flexural strength (FS: n = 10), flexural modulus (FM: n = 10), hardness (H: n = 10), hardness reduction (HR: n = 10), degree of conversion (DC: n = 5), gap width (GW: n = 10), and polymerization shrinkage stress in Class I (SS-I: n = 10) and Class II (SS-II: n = 10) simulated configuration. All test data were analyzed using one-way ANOVA and Tukey's test (α = 0.05; ï¢ = 0.2). Exothane-24 in all concentrations decreased the H, HR, DC, GW, SS-I, and SS-II (p < 0.05) without affecting the UTS, and FS (p > 0.05). Reduction in FM was observed only in the Exothane 40% and 30% groups compared to the control (p < 0.05). Exothane-24 at concentrations 20% and 30% seems suitable since it reduced GW and polymerization SS without affecting the properties of the composite resins tested, except for H.
Subject(s)
Methacrylates , Urethane , Methacrylates/chemistry , Composite Resins/chemistry , Polymethacrylic Acids/chemistry , Bisphenol A-Glycidyl Methacrylate , Polyethylene Glycols/chemistry , Materials Testing , Polymerization , Surface PropertiesABSTRACT
Peri-implantitis is a major cause of dental implant failure. This disease is an inflammation of the tissues surrounding the implant, and, while the cause is multi-factorial, bacteria is the main culprit in initiating an inflammatory reaction. Dental implants with silicon carbonitride (SiCN) coatings have several potential advantages over traditional titanium implants, but their antibacterial efficiency has not yet been evaluated. The purpose of this study was to determine the anti-bacterial potential of SiCN by modifying the surface of SiCN-coated implants to have a positive charge on the nitrogen atoms through the quaternization of the surface atoms. The changes in surface chemistry were confirmed using contact angle measurement and XPS analysis. The modified SiCN surfaces were inoculated with Streptococcus mutans (S. mutans) and compared with a silicon control. The cultured bacterial colonies for the experimental group were 80% less than the control silicon surface. Fluorescent microscopy with live bacteria staining demonstrated significantly reduced bacterial coverage after 3 and 7 days of incubation. Scanning electron microscopy (SEM) was used to visualize the coated surfaces after bacterial inoculation, and the mechanism for the antibacterial properties of the quaternized SiCN was confirmed by observing ruptured bacteria membrane along the surface.
ABSTRACT
Abstract This study aimed to evaluate the effect of an elastomeric urethane monomer (Exothane-24) in different concentrations on physicochemical properties, gap formation, and polymerization shrinkage stress of experimental resin composites. All experimental composites were prepared with 50 wt.% of Bis-GMA and 50 wt.% of TEGDMA, to which 0 wt.% (control), 10 wt.%, 20 wt.%, 30 wt.%, and 40 wt.% of Exothane-24 were added. Filler particles (65 wt.%) were then added to these resin matrixes. Ultimate tensile strength (UTS: n = 10), flexural strength (FS: n = 10), flexural modulus (FM: n = 10), hardness (H: n = 10), hardness reduction (HR: n = 10), degree of conversion (DC: n = 5), gap width (GW: n = 10), and polymerization shrinkage stress in Class I (SS-I: n = 10) and Class II (SS-II: n = 10) simulated configuration. All test data were analyzed using one-way ANOVA and Tukey's test (α = 0.05; β= 0.2). Exothane-24 in all concentrations decreased the H, HR, DC, GW, SS-I, and SS-II (p < 0.05) without affecting the UTS, and FS (p > 0.05). Reduction in FM was observed only in the Exothane 40% and 30% groups compared to the control (p < 0.05). Exothane-24 at concentrations 20% and 30% seems suitable since it reduced GW and polymerization SS without affecting the properties of the composite resins tested, except for H.
Resumo Este estudo teve como objetivo avaliar o efeito de um monômero elastomérico de uretano (Exothane-24) em diferentes concentrações em propriedades físico-químicas, formação de fenda e tensão de contração de polimerização de resinas compostas experimentais. Todos os compósitos experimentais foram preparados com 50% em peso de Bis-GMA e 50% em peso de TEGDMA, nos quais 0% (controle), 10%, 20%, 30% e 40% em peso de Exothane-24 foram adicionados. Partículas de carga (65% em peso) foram então adicionadas as matrizes resinosas. Resistência coesiva (RC: n = 10), resistência à flexão (RF: n = 10), módulo de flexão (MF: n = 10), dureza (D: n = 10), redução de dureza (RD: n = 10), grau de conversão (GC: n = 5), largura de fenda (LF: n = 10) e tensão de contração de polimerização em simulações de cavidades Classe I (TC-I: n = 10) e Classe II (TC-II: n = 10). Todos os dados do teste foram analisados usando one-way ANOVA e teste de Tukey (α = 0,05; β = 0,2). O Exothane-24 em todas as concentrações diminuiu a D, RD, GC, LF, TC-I e TC-II (p < 0,05) sem afetar o RC e RF (p > 0,05). A redução da MF foi observada apenas nos grupos Exothane 40% e 30% em relação ao controle (p < 0,05). O Exothane-24 nas concentrações de 20% e 30% pareceu ser adequado, pois reduziu LF e TC de polimerização sem afetar as propriedades das resinas compostas testadas, exceto para D.
ABSTRACT
OBJECTIVE: This study investigated the ability of a laser, and a 'quad-wave' LCU, to photo-cure paste and flowable bulk-fill resin-based composites (RBCs). METHODS: Five LCUs and nine exposure conditions were used. The laser LCU (Monet) used for 1 s and 3 s, the quad-wave LCU (PinkWave) used for 3 s in the Boost and 20 s in the Standard modes, the the multi-peak LCU (Valo X) used for 5 s in the Xtra and 20 s in the Standard modes, were compared to the polywave PowerCure used in the 3 s mode and for 20 s in the Standard mode, and to the mono-peak SmartLite Pro used for 20 s. Two paste consistency bulk-fill RBCs: Filtek One Bulk Fill Shade A2 (3 M), Tetric PowerFill Shade IVA (Ivoclar Vivadent), and two flowable RBCs: Filtek Bulk Fill Flowable Shade A2 (3 M), Tetric PowerFlow Shade IVA (Ivoclar Vivadent) were photo-cured in 4-mm deep x 4-mm diameter metal molds. The light received by these specimens was measured using a spectrometer (Flame-T, Ocean Insight), and the radiant exposure delivered to the top surface of the RBCs was mapped. The immediate degree of conversion (DC) at the bottom, and the 24-hour Vickers Hardness (VH) at the top and bottom of the RBCs were measured and compared. RESULTS: The irradiance received by the 4-mm diameter specimens ranged from 1035 mW/cm2 (SmartLite Pro) to 5303 mW/cm2 (Monet). The radiant exposures between 350 and 500 nm delivered to the top surface of the RBCs ranged from 5.3 J/cm2 (Monet in 1 s) to 26.4 J/cm2 (Valo X), although the PinkWave delivered 32.1 J/cm2 in 20 s 350 to 900 nm. All four RBCs achieved their maximum DC and VH values at the bottom when photo-cured for 20 s. The Monet used for 1 s and the PinkWave used for 3 s on the Boost setting delivered the lowest radiant exposures between 420 and 500 nm (5.3 J/cm2 and 3.5 J/cm2 respectively), and they produced the lowest DC and VH values. CONCLUSIONS: Despite delivering a high irradiance, the short 1 or 3-s exposures delivered less energy to the RBC than 20-s exposures from LCUs that deliver> 1000 mW/cm2. There was an excellent linear correlation (r > 0.98) between the DC and the VH at the bottom. There was a logarithmic relationship between the DC and the radiant exposure (Pearson's r = 0.87-97) and between the VH and the radiant exposure (Pearson's r = 0.92-0.96) delivered in the 420-500 nm range.
Subject(s)
Acrylic Resins , Dental Materials , Polyurethanes , LasersABSTRACT
The aim was to evaluate the marginal-gap formation and curing profile of a new restorative technique using a liner with long-wavelength-absorbing photoinitiator (LWAP). Box-shaped preparations (6 mm × 4 mm × 4 mm) were made in third molars. All samples were treated with Clearfill SE Bond and divided into 4 groups (n = 5), according to restorative technique used: (1) incremental technique (INC-Technique); (2) camphorquinone-based liner (CQ-Liner) + bulk-fill resin composite; (3) LWAP-based liner (LWAP-Liner) + bulk-fill resin composite; and (4) bulk-fill technique without liner (BF-Technique). The marginal gaps (%) for all the samples were measured using micro-computed tomography. The restorations were cross-sectioned, and the degree of conversion (DC) and Knoop microhardness were evaluated at different depths (0.3, 1, 2, 3, and 4 mm). INC-Technique, CQ-Liner, and LWAP-Liner groups showed significantly fewer marginal gaps than those from the BF-Technique group. The BF-Technique specimens had the lowest DC and microhardness in depth. All the other techniques presented similar degree of conversion and microhardness at all the depths. The use of liners, regardless of the photoinitiator system, decreased the marginal-gap formation and improved the curing profile of bulk-filling restoration technique.
Subject(s)
Camphor , Composite Resins , X-Ray Microtomography , Materials Testing , Polymerization , Composite Resins/chemistry , Dental Restoration, PermanentABSTRACT
This article compares the accuracy of intraoral scanners (IOSs) used in the digital impression of full arches to fabricate implant-supported complete prostheses. This study followed the Preferred Reporting Items for Systematic Reviews and Meta-Analyses guidelines and was registered in the Open Science Framework (DOI 10.17605/OSF.IO/CPM9K). Six electronic databases, gray literature databases, and a manual search were performed in April 2022. Studies that evaluated the accuracy of intraoral scan impressions compared with conventional impressions in full-arch impressions were included for complete implant-supported prostheses. In addition, an adapted checklist for reporting in vitro studies was used to assess the risk of bias. Meta-analysis was conducted using a random-effects Hunter- Schmidt model. Nine studies were included in the analysis. IOS impressions present higher accuracy (137.86 µm) than conventional impressions (182.51 µm) (p<0.001). The heterogeneity of the study's methodology was I2»18.34. However, impression accuracy varies significantly with scan body type, IOS type, scanning strategy, and modification technique. For most IOS systems, the acceptable clinical threshold of linear accuracy of 200 µm can be achieved, except for the True Definition Scanner in one of the studies. Based on the results of the included studies, digital impressions using IOS present similar or better linear accuracy than conventional impression techniques.
ABSTRACT
OBJECTIVES: The aim of this study was to evaluate the accuracy of machine learning regression models in predicting the final color of leucite-reinforced glass CAD/CAM ceramic veneer restorations based on substrate shade, ceramic shade, thickness and translucency. METHODS: Leucite-reinforced glass ceramics in four different shades were sectioned in thicknesses of 0.3, 0.5, 0.7, and 1.2 mm. The CIELab coordinates of each specimen were obtained over four different backgrounds (black, white, A1, and A3) interposed with an experimental translucent resin cement using a calibrated spectrophotometer. The color change (CIEDE2000) values, as well as all the CIELab values for each one of the experimental groups, were submitted to 28 different regression models. Each regression model was adjusted according to the weights of each dependent variable to achieve the best-fitting model. RESULTS: Different substrates, ceramic shades, and thicknesses influenced the L, a, and b of the final restoration. Of all variables, the substrate influenced the final ceramic shade most, followed by the ceramic thickness and the L, a, and b of the ceramic. The decision tree regression model had the lowest mean absolute error and highest accuracy to predict the shade of the ceramic restoration according to the substrate shade, ceramic shade and thickness. CLINICAL SIGNIFICANCE: The machine learning regression model developed in the study can help clinicians predict the final color of the ceramic veneers made with leucite-reinforced glass CAD/CAM ceramic HT and LT when cemented with translucent cements, based on the color of the substrate and ceramic thicknesses.
Subject(s)
Artificial Intelligence , Dental Porcelain , Ceramics , Aluminum Silicates , Resin Cements , Color , Materials Testing , Surface PropertiesABSTRACT
Background: Intraoral scanners (IOS) are gaining interest in Dentistry for their ability to capture digital impressions of the oral cavity. These digital impressions facilitate the fabrication of indirect restorations using CAD/CAM technology. This study aimed to describe an elective course given to predoctoral dental students on the topic of Digital Dentistry and assess their learning outcomes and system preferences. Material and Methods: Three IOS were evaluated by eight students enrolled in a Digital Dentistry elective course. These systems included Emerald S (Planmeca), Cerec Omnicam (Denstply Sirona), and True Definition (3M/Midmark). After a literature review and a hands-on session were completed for each system, the students provided their perspectives on various factors such as ease of use, organization, and user-friendliness in a qualitative narrative of each system and quantitatively through a six-items survey. Results: Survey data suggests that the student cohort showed higher levels of previous familiarity, user preference, and clinical confidence in the Cerec and Planmeca systems as opposed to the True Definition system. Qualitatively, the students felt CEREC was the more educationally useful system to learn and presented with more ease of use, functionality, and efficacy than the other two systems. Conclusions: While each system proved to have its unique benefits and drawbacks, students' attitudes towards the Planmeca and Cerec systems were generally positive, while True Definition's evaluation was limited. Students appreciated their experiences throughout this elective, familiarizing themselves with various digital systems. Key words:Digital Dentistry, Intraoral Scanners, CAD/CAM, Dental Education, Learning Curve.
ABSTRACT
BACKGROUND: Dental zirconium oxide restorations are milled from pre-sintered blocks or disks which are produced either with high isostatic pressure (HIP) or, simpler, a slurry technique. The objective was to perform a fatigue test and an in vitro wear simulation of two ceramics, yttria-stabilized tetragonal zirconia polycrystal (3Y-TZP) ceramic and a hybrid zirconium oxide-aluminum oxide ceramic, (ATZ) both produced either the classical way using high isostatic pressure (HIP, control) or with a slurry technique. MATERIALS AND METHODS: Ten discs/group were subjected to a cyclic biaxial fatigue test using a staircase approach under water at 37 °C in a dynamic universal testing machine. The 2-body wear test was performed on eight lapped 12 mm thick cylindrical samples subjected to spherical (ø 6 mm) leucite ceramic antagonists in a CS-4 chewing simulator at 49 N force and 0.7 mm lateral movement for 600 k cycles and 4167 thermal cycles (5-55 °C). Volumetric wear was calculated based on laser-scanned surfaces. Selected samples of both tests were viewed in SEM. RESULTS: All the ceramic specimens produced using the HIP method survived up to 1.2 M cycles with the maximum load of the equipment (1000 N) loading the specimens up to 1527 MPa. The fatigue limit stress at 1.2 M cycles for the Slurry ATZ samples was 946 MPa. For the Slurry Y-TZP samples the fatigue limit stress at 1.2 M cycles was 658 MPa. At 600 k cycles, all zirconium oxide ceramics showed no measurable wear and had a highly polished appearance. The leucite ceramic antagonists wear developed in a linear way. There was no difference between the materials produced with the slurry and the HIP process. ATZ ceramic produced significantly more wear than 3Y- TZP ceramic. CONCLUSIONS: The HIP method provided higher fatigue strength than the Slurry manufacturing method. All HIP ceramics surpassed the limit threshold (1527 MPa) of the testing machine. The tested ceramics did not show any measurable wear but had worn the leucite reinforced glass ceramic antagonists for a considerable amount.
Subject(s)
Ceramics , Zirconium , Materials Testing , Surface Properties , Zirconium/chemistry , Ceramics/chemistry , Yttrium/chemistry , Dental PorcelainABSTRACT
This article focuses on the current understanding and concerns over the blue-light hazard when using dental light-curing units. It also provides information and safety protocols to guide the practitioner in making important decisions regarding dental personnel's health and the quality of dental restorations.
Subject(s)
Curing Lights, Dental , Light-Curing of Dental Adhesives , Composite Resins , HumansABSTRACT
This study aimed to evaluate the biomechanical behavior of Morse taper implants using different abutments (CMN abutment [(CMN Group] and miniconical abutments [MC Group]), indicated to support a screw-retained 3-unit fixed partial denture. For the in vitro test, polyurethane blocks were fabricated for both groups (n = 10) and received three implants in the "offset" configuration and their respective abutments (CMN or MC) with a 3-unit fixed partial denture. Four strain gauges were bonded to the surface of each block. For the finite element analysis, 3D models of both groups were created and exported to the analysis software to perform static structural analysis. All structures were considered homogeneous, isotropic, and elastic. The contacts were considered non-linear with a friction coefficient of 0.3 between metallic structures and considered bonded between the implant and substrate. An axial load of 300 N was applied in three points (A, B, and C) for both methods. The microstrain and the maximum principal stress were considered as analysis criteria. The obtained data were submitted to the Mann-Whitney, Kruskal-Wallis, and Dunn's multiple comparison test (α = 5%). The results obtained by strain gauge showed no statistical difference (p = 0.879) between the CMN (645.3 ± 309.2 µÎµ) and MC (639.3 ± 278.8 µÎµ) and allowed the validation of computational models with a difference of 6.3% and 6.4% for the microstrains in the CMN and MC groups, respectively. Similarly, the results presented by the computational models showed no statistical difference (p = 0.932) for the CMN (605.1 ± 358.6 µÎµ) and MC (598.7 ± 357.9 µÎµ) groups. The study concluded that under favorable conditions the use of CMN or MP abutments to support a fixed partial denture can be indicated.
ABSTRACT
Background: To evaluate the intra-pulpal temperature during different direct pulp capping methods and light-cured procedures. Material and Methods: Class I preparations 5 mm long, 4 mm wide and 4 mm deep were performed in extracted third molars, leaving 0.5 mm of dentin at the pulpal floor with a 1 mm diameter of pulp exposure. Teeth were placed in a customized oral cavity chamber simulator in which the initial temperature was standardized at 36oC. The overall temperature variations (oC) in the pulp chamber during the light-activation processes were recorded live using an infrared camera (FLIR ONE PRO, FLIR Systems). The liners and bases evaluated were: Dycal (Dentisply), TheraCal LC (Bisco), Biodentin (Septodent), Vitrebond Plus (3M/ESPE), and Fuji IX GP (GC), followed by restoration with a bulk fill composite (EvoCeram Bulk Fill, Ivoclar Vivadent). All light-activation procedures were performed with the VALO Grand (Ultradent) light-curing unit. A power analysis was conducted to determine the sample size to provide a power of at least 0.8 with α=0.05. Statistical analyses were performed using ANOVA and Tukey's test for multiple comparisons. Results: The intrapulpal temperature increased above a 10oC to 20oC threshold difference for all liners and bases that were light cured. When added as second layers, neither of those could provide thermal insulation following additional light-activated procedures (p=0.25). The higher the number of procedures requiring light-activation, the longer the pulp temperature remained in those increased temperature thresholds. Conclusions: For direct pulp capping procedures, a reduced number light activation procedures should be indicated to reduce the time intra-pulpal temperature rises above a 10oC threshold. Key words:Liner, base, calcium hydroxide, glass ionomer, dental adhesive, bulkfill composite.
ABSTRACT
Background: The purpose of this in vitro study was to evaluate the color difference between the Vita Classical Shade Guide and composite veneers using the dual-layer technique. Material and Methods: Thirty samples were fabricated using a custom-made mold (Easy Layering Shade Guide Kit, 3M) using two resin composites: Filtek Supreme Ultra (3M); and Estelite Omega (Tokuyama) (n=3). The composite veneers were made by layering the different enamel and body or dentin shades from each composite. The color measurements were taken using a spectrophotometer (Vita Easyshade V®, Vita Zahnfabrik). The ΔE00 between the Vita Classical Shade Guide (Vita Zahnfabrik) and the composite veneers were calculated using the CIEDE2000 formula. Results: For the composite veneers using Filtek Supreme Ultra, the best match for A1 Vita shade was achieved layering either EA1 with DA2 or DA3; EA2 with DA1 or DA2 (ΔE00= 1.53 ~ 1.96 ± 0.4). For A2 Vita shade the best match would be EA3 with DA3 or EA3 with DA2 (ΔE00= 1.40 ~ 1.85 ± 0.1); or for A3 Vita shade the best match would be EA3 with DA2 2.50±(0.6). For the composite veneers using Estelite Omega, the were no best match for neither A1, A2 or A3 Vita shade (ΔE00> 2.5). Conclusions: The combination of enamel and dentin shades from Filtek Supreme Ultra provided acceptable color match for A1, A2 and A3 shades from the Vita Shade Guide, while Estelite Omega did not provide acceptable color match for any of the Vita Shade Guide standard shades tested. Key words:Color, color matching, optical properties, resin composite, layering.
ABSTRACT
This study aimed to evaluate the effect of light attenuation through ceramic veneers and resin cement on degree of conversion (DC), cohesive strength (CS), and microshear bond strength (µSBS) of experimental adhesive systems. Experimental etch-and-rinse and self-etch adhesives were combined with different ratios of camphorquinone (CQ) and diphenyl(2,4,6-trimethylbenzoyl) phosphine oxide (TPO) photoinitiators: CQ-only; 3CQ:1TPO; 1CQ:1TPO; 1CQ:3TPO and TPO-only. Square-shaped ceramic veneer (IPS Empress Esthetic, Ivoclar Vivadent) (n = 10; 10mm long x 10mm wide x 0.5mm thick) and resin cement specimens (Variolink Esthetic LC, Ivoclar Vivadent) (n = 10; 10 mm long x 10 mm wide and 0.3 mm thick) were prepared. Light transmittance of a multiple-peak LED (Bluephase G2, Ivoclar Vivadent) was measured through restorative materials using a spectrometer (n = 5). Adhesive specimens were analyzed for DC, CS, and µSBS by light-curing the adhesive with or without (control) ceramic veneer, and with resin cement fixed to output region of the light-curing tip (n = 10). Data were submitted to ANOVA and Tukey's test (α = 0.05). Total light transmittance through the restorative materials was attenuated, and this attenuation was more evident for the violet spectrum. The DC for the TPO groups in ratios up to 1CQ:1TPO was similar to the control. 1CQ:3TPO showed lower values for CS. µSBS was reduced for all groups with light attenuation, but lower values were observed for 1CQ:3TPO and TPO-only. In conclusion, light transmission was reduced with interposed restorative materials. Adhesives combined with CQ and TPO up to 1CQ:1TPO showed greater cure efficiency and mechanical properties compared with a higher amount of TPO.
Subject(s)
Dental Cements , Resin Cements , Ceramics , Dental Materials , Light-Curing of Dental Adhesives , Materials Testing , Resin Cements/chemistryABSTRACT
Background: The use of dental headlights is a common practice to better illuminate the operatory field and achieve excellence in restorative dentistry. However, visible light-cured dental materials can have reduced working time under headlight illumination. The aim of this study was to evaluate the influence of the spectral irradiance power of two dental headlights on the degree of polymerization and working time of light-curable dental composites. Material and Methods: Two headlights, StarLight Nano 3 (StarMed) (SN) and Zeon Endevour XL (Orascoptic) (ZE) were characterized using a spectrophotometer coupled to an integrating sphere (MARC® Light Collector, BlueLight Analytics). The degree of conversion of the two composites, Filtek Supreme (3M) and Tetric Prime (Ivoclar Vivadent), was evaluated using an FTIR spectroscope (NicoletTM iS20, Thermo Fisher). Results: Both headlights emitted a significant amount of blue light. The Zeon headlamp without filter emitted a broader spectrum with lower blue intensity and higher CRI than the White LED of the Nano 3. The Zeon headlamp with the blue blocking filter emitted a broader spectrum than the Orange LED of the Nano 3. There were no differences in the degree of conversion and working time of the Filtek Supreme and Tetric Prime composites when illuminated by the different headlamps. Both Zeon and the White LED of the Nano 3 were capable to cure the composites within only 5-10 minutes of irradiation. There were no changes in the degree of conversion of the composites when the Orange LED of the Nano 3 or the blue blocking filter of the Zeon were used. Conclusions: Both headlights reduced the working time of light-cured materials. The use of orange filters prevented the composite polymerization and maintained the working time. Key words:Surgical Headlight, degree of conversion, working time, light-curing.
ABSTRACT
OBJECTIVES: To evaluate the depth of cure (DOC) of ten contemporary resin-based composites (RBCs), light-cured using different LCUs and exposure times. METHODS: The power, radiant emittance, irradiance, radiant exposure (RE), and beam profiles from a laser (M, Monet), a multi-peak (V, Valo Grand), and single-peak (S, SmartLite Pro) LCU were measured. The DOC was measured using a 6-mm diameter metal mold and a solvent dissolution method to remove the uncured RBC. The length of the remaining RBC was divided by 2. The exposure times were: 1 s and 3 s for M, 10 s and 20 s for V, and 10 s and 20 s for S. Data were analyzed using: Bland-Altman distribution, Pearson's Correlation, and an artificial neural network (ANN) to establish the relative importance of the factors on the DOC (α=0.05; ß=0.2). RESULTS: Significant differences were found in the DOC achieved by the different LCUs and composites. The laser LCU emitted the highest power, radiant emittance is used above and in the tables and delivered the highest irradiance. However, this LCU used for 1 s delivered the lowest RE and produced the shortest DOC in all ten RBCs. The ANN demonstrated that the RE is the most critical factor for the DOC. Bland-Altman comparisons showed that the DOCs achieved with the laser LCU used for 1 s were between 17 and 34% shorter than the other conditions. CONCLUSIONS: Although the laser LCU cured all 10 RBCs when used for 1 s, it produced the shallowest DOC, and some RBCs did not achieve their minimum DOC threshold. The RE and not the irradiance was the most important factor in determining the DOC of these 10 RBCs. CLINICAL SIGNIFICANCE: Despite delivering high power and irradiance, the laser used for l s delivered a lower radiant exposure than the conventional LCUs used for 10 s. This resulted in a shorter DOC.
Subject(s)
Composite Resins , Curing Lights, Dental , Dental Materials , Lasers , Materials Testing , PolymerizationABSTRACT
The objective of this in vitro study was to evaluate the mechanical properties of different bulk-fill composite resins with or without a final layer of conventional composite resin. The null hypothesis was that the mechanical properties of the material would not change regardless of the addition of a layer of conventional composite. Bar-shaped specimens (25 × 2 × 2 mm) were made from 4 different bulk-fill composites (Filtek One Bulk Fill, Filtek Bulk Fill Flowable, Tetric EvoCeram Bulk Fill, and Tetric EvoCeram Bulk Fill Flow) with or without a final layer of a conventional composite of the same brand (Filtek Supreme for the Filtek materials and Tetric EvoCeram for the Tetric materials). Each specimen was light cured at 2 equidistant points using a multiwave curing light with a power output of 20 J/cm2. All of the specimens were subjected to a 3-point bending test in a universal testing machine at a crosshead speed of 0.75 ± 0.25 mm/min and a load rate of 50 ± 16 N/min, and the flexural strength and elastic modulus were calculated. The mean flexural strength and elastic modulus values were analyzed using 1-way analysis of variance, and then the Tukey test was applied for multiple comparisons between groups (α = 0.05). When a final layer of a conventional composite of the same brand was added, the mean flexural strength of the Tetric groups slightly decreased, while that of the Filtek groups did not change. Application of a final layer of conventional composite resulted in a slight increase in the mean elastic modulus of the Filtek groups and either no change or a slight decrease in the Tetric groups. The addition of a final layer of conventional composite resin did not seem to improve the mechanical properties of any of the tested bulk-fill materials. The addition of a final layer of conventional composite resin can affect the mechanical properties of bulk-fill materials; however, it seems these effects are dependent on the type of conventional composite resin used for the final layer.
Subject(s)
Composite Resins , Dental Materials , Composite Resins/therapeutic use , Dental Materials/therapeutic use , Elastic Modulus , Humans , Materials TestingABSTRACT
The purpose was to evaluate the effect of tris(trimethylsilyl)silane (TTMSS) associated with diphenyl iodonium hexafluorophosphate (DPIHP) on the polymerization shrinkage stress (PSS), mechanical properties, color change (CC), and degree of conversion (DC) of resin-based composites (RBCs). Experimental RBCs containing 35 wt% of organic matrix (10.2 wt% BisGMA, 11.1 wt% BisEMA10 and UDMA and 2.1 wt% TEGDMA) and 65 wt% filler (13 wt% fumed silica and 52 wt% BaBSiO2) were assigned to six groups: control (0.2 wt% CQ, 0.5 wt% DMAEMA); TD05 (0.2 wt% CQ, 0.5 wt% TTMSS, 0.5 wt% DPIHP); TD10 (0.2 wt% CQ, 1 wt% TTMSS, 0.5 wt% DPIHP); DTD (0.2 wt% CQ, 0.25 wt% of DMAEMA, 0.25 wt% TTMSS, 0.5 wt% DPIHP); DT (0.2 wt% CQ, 0.25 wt% DMAEMA, 0.25 wt% TTMSS); and T05 (0.2 wt% CQ, 0.25 wt% TTMSS). The experimental formulations were submitted to the following tests: DC; PSS; CC; rate of polymerization (Rp); depth of cure by Knoop hardness; flexural strength; and flexural modulus. TTMSS showed no effect on the DC, Rp, and mechanical properties of the RBCs. DMAEMA reacted with TTMSS and reduced the Rp; the RBCs containing no DMAEMA showed no reduction in CC. DT showed the lowest PSS mean value among the groups. TTMSS differed from DMAEMA only when used in combination with DPIHP, which significantly improved the DC, maximum Rp, and mechanical properties of the RBCs tested. Based on the artificial ageing results, TTMSS was ineffective in reducing CC in the RBCs tested.