ABSTRACT
This study assessed for the first time the bioremediation potential of an organic horse amendment in soils contaminated with solid wastes of the obsolete pesticide lindane (α-hexachlorocyclohexane (α-HCH) = 80 mg kg-1, ß-HCH = 40 mg kg-1, γ,δ,ε-HCH≈10 mg kg-1) searching for a self-sufficient bio-based economy. Four treatments were implemented: polluted (PS, ΣHCHs = 130 mg kg-1) and control (CS, ΣHCHs = 1.24 mg kg-1) soils and the respective amended soils (APS and ACS). A commercial amendment, coming from organic wastes, was used for soil biostimulation (5% dry weight), and the temporal evolution of the enzymatic activity (dehydrogenase, ß-glucosidase activity, phenoloxidase, arylamidase, phosphatase, and urease) and HCHs concentration of the soils was evaluated over 55 days under controlled humidity and temperature conditions. The horse amendment positively influenced the physicochemical properties of the soil by reducing pH (from 8.3 to 8) and increasing the organic matter (TOC from 0.5 to 3.3%) and nutrient content (P and NH4+ from 24.1 to 13.7 to 142.1 and 41.2 mg kg-1, respectively). Consequently, there was a notable enhancement in the soil biological activity, specifically in the enzymatic activity of dehydrogenase, phenol-oxidase, phosphatase, and urease and, therefore, in HCH degradation, which increased from <1 to 75% after the incubation period. According to the chlorine position on the cyclohexane ring, the following ranking has been found for HCHs degradation: ß-HCH (46%) < ε-HCH (57%) < α-HCH (91%) ≈ δ-HCH (91%) < γ-HCH (100%). Pentachlorocyclohexene (PCCH) and 1,2,4-trichlorobenzene (1,2,4-TCB) were identified as HCHs degradation metabolites and disappeared at the end of the incubation time. Although further research is required, these preliminary findings suggest that organic amendments represent a sustainable, harmless, and cost-effective biostimulation approach for remediating soils contaminated with recalcitrant HCHs, boosting the circular economy.
Subject(s)
Biodegradation, Environmental , Hexachlorocyclohexane , Soil Pollutants , Soil , Soil/chemistry , Horses , AnimalsABSTRACT
The LIFE SURFING Project was carried out at the Bailin Landfill in Sabiñánigo, Spain (2020-2022), applying Surfactant Enhanced Aquifer Remediation (SEAR) and In Situ Chemical Oxidation (S-ISCO) in a 60-meter test cell beneath the old landfill, to remediate a contaminated aquifer with dense non-aqueous phase liquid (DNAPL) from nearby lindane production. The project overcame traditional extraction limitations, successfully preventing groundwater pollution from reaching the river. In spring 2022, two SEAR interventions involved the injection of 9.3 m3 (SEAR-1) and 6 m3 (SEAR-2) of aqueous solutions containing 20 g/L of the non-ionic surfactant E-Mulse 3®, with bromide (around 150 mg/L) serving as a conservative tracer. 7.1 and 6.0 m3 were extracted in SEAR-1 and SEAR-2, respectively, recovered 60-70 % of the injected bromide and 30-40 % of the surfactant, confirming surfactant adsorption by the soil. Approximately 130 kg of DNAPL were removed, with over 90 % mobilized and 10 % solubilized. A surfactant-to-DNAPL recovery mass ratio of 2.6 was obtained, a successful value for a fractured aquifer. In September 2022, the S-ISCO phase entailed injecting 22 m3 of a solution containing persulfate (40 g/L), E-Mulse 3® (4 g/L), and NaOH (8.75 g/L) in pulses over 48 h, oxidizing around 20 kg of DNAPL and ensuring low toxicity levels after that. Preceding the SEAR and S-ISCO trials, 2020 and 2021 were dedicated to detailed groundwater flow characterizations, including hydrological and tracer studies. These preliminary investigations allowed the design of a barrier zone between 317 and 557 m from the test cell and the river, situated 900 m away. This zone, integrating alkali dosing, aeration, vapor extraction, and oxidant injection, effectively prevented the escape of fluids to the river. Neither surfactants nor contaminants were detected in river waters post-treatment. The absence of residual phase in test cell wells and reduction of chlorinated compound levels in groundwater were noticed till one year after S-ISCO.
ABSTRACT
This work studies the remediation of groundwater saturated with dense non-aqueous phase liquid (DNAPL) from lindane production wastes by electrochemical oxidation. DNAPL-saturated groundwater contains up to 26 chlorinated organic compounds (COCs), including different isomers of hexachlorocyclohexane (HCH). To do this, polluted groundwater was electrolysed using boron-doped diamond (BDD) and stainless steel (SS) as anode and cathode, respectively, and the influence of the current density on COCs removal was evaluated in the range from 5 to 50 mA cm-2. Results show that current densities higher than 25 mA cm-2 lead to the complete removal and mineralisation of all COCs identified in groundwater. The higher the current density, the higher the COCs removal rate. At lower current densities (5 mA cm-2), chlorobenzenes were completely removed, and degradations above 90 % were reached for COCs with more than five chlorine atoms in their molecules. The use of BDD anodes promotes the electrochemical generation of powerful reactive species, such as persulfate, hypochlorite or hydroxyl radicals, that contribute to the degradation and mineralisation of COCs. The applied current density also influences the generation of these species. Finally, no acute toxicity towards Vibrio fischeri was observed for the treated groundwater after the electrochemical oxidation performed at 5 and 10 mA cm-2. These findings demonstrate that electrochemical oxidation with BDD anodes at moderate current densities is a promising alternative for the remediation of actual groundwater contaminated with DNAPLs.
ABSTRACT
The uncontrolled disposal of the liquid lindane wastes have led to the formation of dense non-aqueous phase liquids (DNAPL), consisting of 28 chlorinated organic compounds (COCs), contaminating soil and groundwater. Surfactant-enhanced aquifer remediation is proposed as technology to treat these sites. However, the polluted emulsion generated must be manged on-site. In this work a two-step process is applied to treat emulsion composed of E-Mulse® 3 (4 g·L-1) as surfactant and a DNAPL (2 gCOCs·L-1). In the first, the COCs were selectively adsorbed in a granular activated carbon (GAC) column with Fe (II) previously adsorbed (10-20mg·g-1) onto the carbon surface, recovering an aqueous phase with surfactant for their reuse. In the second step, the spent GAC was regenerated with a 40 g·L-1 solution of hydrogen peroxide fed to the column at 2 mL·min-1 to promote the oxidation of the COCs adsorbed in the GAC. The kinetic and adsorption model in a multisolute (surfactant and DNAPL) system has been proposed. Five successive cycles of regeneration/adsorption have been successfully applied in the column process. About 50 % of the COCs were retained from the emulsion, and more than 70 % of the surfactant was recovered. The consumption of unproductive oxidants decreased with the number of regeneration cycles. The water effluent obtained after regeneration of GAC did not present chlorinated compounds desorbed and nontoxic by-products generated, such as short-chain acids.
ABSTRACT
The oxidation of hexachlorocyclohexane isomers in the aqueous phase (Milli-Q and groundwater) was studied using persulfate activated by ferrioxalate and solar light at circumneutral pH. The experiments were conducted in a solar simulator reactor with local radiation fluxes qw= 1.12·10-7 E cm-2s-1 and in compound parabolic collectors with solar light (qw≈10-7 E cm-2s-1) for 390 min. The effect of activator dosage (18-125 µM ferrioxalate) and persulfate concentration (520-2600 µM) on hexachlorocyclohexane conversion and oxalate and oxidant consumption was analyzed. Conversion of about 95% of ß isomer was achieved at 390 min using 1300 µM of initial persulfate and 63 µM of Fe3+ concentration despite this ß isomer being the most recalcitrant to oxidation (XHexachlorocyclohexanes=0.98). Dechlorination above 80% was achieved under these conditions, analyzing the chlorides released into the water. The influence of chloride and bicarbonate on hexachlorocyclohexanes degradation was analyzed in milli-Q water and in groundwater. Hexachlorocyclohexane conversion at 390 min decreases from 98% to 83, 75 and 65% in the presence of chloride, bicarbonate or groundwater, respectively. Results obtained with compound parabolic collectors and solar light using 2600 µM Na2S2O8 and 63 µM Fe for removing hexachlorocyclohexanes agreed with those from the solar simulator reactor, supporting using solar light to activate persulfate for sustainable abatement of persistent organic pollutants in aqueous matrixes.
Subject(s)
Groundwater , Pesticides , Water Pollutants, Chemical , Hexachlorocyclohexane , Bicarbonates , Chlorides , Oxalates/chemistry , Groundwater/chemistry , Water , Oxidation-Reduction , Water Pollutants, Chemical/analysis , Sulfates/chemistryABSTRACT
A common strategy for removing highly toxic organic compounds, such as chlorinated organic compounds, is their adsorption on granular activated carbon. Spent granular activated carbon results in a toxic residue to manage; therefore, the regeneration and reuse of granular activated carbon on the site would be advisable. This work studies the regeneration of a granular activated carbon saturated in 1,2,4-trichlorobenzene, chosen as the model chlorinated organic compounds, by heterogeneous Fenton, where iron was previously immobilised on the granular activated carbon surface. This methodology avoids the addition of iron to the aqueous phase at concentrations above the allowable limits and the need for acidification. Three successive cycles of adsorption-regeneration were carried out batchwise (5 gGAC·L-1) with a granular activated carbon saturated with 300 mg124-TCB·gGAC-1. The recovery of the adsorption capacity after regeneration was studied with H2O2 (166 mM, 1.5 the stoichiometric dosage), at different concentrations adsorbed with iron adsorbed concentrations (0-12 mgFe·gGAC-1) and temperatures (20-80 °C). Stable recovery of the adsorption capacity values of 65% were obtained at 180 min with 12 mgFe·gGAC-1 and 60 °C. The porosity and surface chemistry of the adsorbent remained very similar after different adsorption-regeneration cycles without iron leaching into the aqueous phase. The oxidant consumption was close to the stoichiometric value for the mineralization of 1,2,4-trichlorobenzene, with a low unproductive consumption of H2O2 with granular activated carbon. In addition, no aromatic or chlorinated by-products were detected in the aqueous solution obtained in the regeneration process. The negligible toxicity of the aqueous phase with the Microtox bioassay confirmed the absence of toxic oxidation by-products.
Subject(s)
Hydrogen Peroxide , Water Pollutants, Chemical , Hydrogen Peroxide/chemistry , Charcoal , Temperature , Iron/chemistry , Adsorption , Water Pollutants, Chemical/chemistryABSTRACT
Surfactant-enhanced aquifer remediation is commonly applied in polluted sites with dense non-aqueous phase liquids (DNAPLs). This technique transfers the contamination from subsoil to an extracted emulsion, which requires further treatment. This work investigated the treatment of a complex emulsion composed of a nonionic surfactant and real DNAPL formed of chlorinated organic compounds (COCs) and generated as a lindane production waste by air stripping under alkaline conditions. The influence of the surfactant (1.5-15 g·L-1), COC concentrations (2.3-46.9 mmol·L-1), and temperature (30-60 °C) on the COC volatilization was studied and modeled in terms of an apparent constant of Henry at pH > 12. In addition, the surfactant stability was studied as a function of temperature (20-60 °C) and surfactant (2-10 g·L-1), COC (0-70.3 mmol·L-1), and NaOH (0-4 g·L-1) concentrations. A kinetic model was successfully proposed to explain the loss of surfactant capacity (SCL). The results showed that alkali and temperature caused the SCL by hydrolysis of the surfactant molecule. The increasing surfactant concentration decreased the COC volatility, whereas the temperature improved the COC volatilization. Finally, the volatilization of COCs in alkaline emulsions by air stripping (3 L·h-1) was performed to evaluate the treatment of an emulsion composed of the COCs (17.6 mmol·kg-1) and surfactant (3.5 and 7 g·L-1). The air stripping was successfully applied to remove COCs (>90%), reaching an SCL of 80% at 60 °C after 8 h. Volatilization can remove COCs from emulsions and break them, enhancing their further disposal.
ABSTRACT
This research studies the acute toxicity of real contaminated soils (topsoil and subsoil) with hazardous chlorinated organic compounds (COCs) from lindane manufacturing wastes. The Microtox® bioassay was used to determine the toxicity of soils (modified Basic Solid Phase Test), soil elutriates (Basic Test), and organic extracts (adapted Organic Solvent Sample Solubilization Test), in which hydrophobic organic compounds are soluble. The acute toxicity of these persistent contaminants (hexachlorocyclohexanes, HCH isomers, as particulate matter in topsoil, and COCs, from dense non-aqueous phase liquid, DNAPL, in subsoil) and the commercial compounds were also measured. Soils tested showed different contaminant levels (topsoil: 0.9-1149 mg/kg and subsoil: 20-9528 mg/kg). Soil contaminants distribution, concentration and acute toxicity were highly related to the contamination source (HCHs or DNAPL). Soils, organic extracts, and subsoil elutriates presented high toxicity, highlighting the need for remediation of these sites. EC50 was calculated in the three-test applied for the soils tested. EC50 vs. COCs concentration in soils and soil elutriates showed an asymptotic trend, explained by the low pollutants solubility in the aqueous phase. Contrarily, EC50 vs. soil COCs concentration was more linear in the case of the organic extracts. This test was the most reliable from statistical analysis. The three methods reveal interesting and complementary information and are necessary for a complete overview of the acute toxicity of contaminated soils.
Subject(s)
Hexachlorocyclohexane , Soil Pollutants , Hexachlorocyclohexane/analysis , Soil/chemistry , Soil Pollutants/analysis , Environmental Pollution/analysis , Biological AssayABSTRACT
The discharge of lindane wastes in unlined landfills causes groundwater and soil pollution worldwide. The liquid waste generated (a mixture of 28 chlorinated organic compounds, COCs) constitutes a dense non-aqueous phase liquid (DNAPL) that is highly persistent. Although in situ chemical oxidation (ISCO) is effective for degrading organic pollutants, the low COCs solubility requires high reaction times. Simultaneous injection of surfactants and oxidants (S-ISCO) is a promising technology to solve the limitation of ISCO treatment. The current work studies the remediation of highly polluted soil (COCs = 3682 mg/kg) obtained at the Sardas landfill (Sabiñáñigo, Spain) by ISCO and S-ISCO treatments. Special attention is paid to acute soil toxicity before and after the soil treatment. Microtox®, modified Basic Solid-Phase Test (mBSPT) and adapted Organic Solvent Sample Solubilization Test (aOSSST) were used for this scope. Persulfate (PS, 210 mM) activated by alkali (NaOH, 210 mM) was used in both ISCO and S-ISCO runs. A non-ionic and biodegradable surfactant selected in previous work, Emulse®3 (E3, 5, and 10 g/L), was applied in S-ISCO experiments. Runs were performed in soil columns filled with 50 g of polluted soil, with eight pore volumes (Pvs) of the reagents injected and 96 h between successive Pv injections. The total treatment time was 32 days. The results were compared with those corresponding without surfactant (ISCO). After remediation treatments, soils were water-washed, simulating the conditions of groundwater flux in the subsoil. The treatments applied highly reduced soil toxicity (final soil toxicity equivalent to that obtained for non-contaminated soil, mBSPT) and organic extract toxicity (reduction > 95%, aOSSST). Surfactant application did not cause an increase in the toxicity of the treated soil, highlighting its suitability for full-scale applications.
Subject(s)
Groundwater , Pulmonary Surfactants , Soil Pollutants , Water Pollutants, Chemical , Hexachlorocyclohexane/toxicity , Surface-Active Agents/toxicity , Environmental Pollution , Oxidation-Reduction , Water Pollutants, Chemical/chemistry , Soil/chemistry , Soil Pollutants/toxicity , Soil Pollutants/chemistry , Groundwater/chemistryABSTRACT
Chlorinated organic compounds (COCs) are among the more toxic organic compounds frequently found in soil and groundwater. Among these, toxic and low-degradable chlorobenzenes are commonly found in the environment. In this work, an innovative process using hydrogen peroxide as the oxidant, ferrioxalate as the catalyst and a visible light-emitting diode lamp (Vis LED) were applied to successfully oxidize 124-trichlorobenzene (124-TCB) in a saturated aqueous solution of 124-TCB (28 mg L-1) at a neutral pH. The influence of a hydrogen peroxide (HP) concentration (61.5-612 mg L-1), Fe3+ (Fe) dosage (3-10 mg L-1), and irradiation level (Rad) (I = 0.12 W cm-2 and I = 0.18 W cm-2) on 124-TCB conversion and dechlorination was studied. A D-Optimal experimental design combined with response surface methodology (RSM) was implemented to maximize the quality of the information obtained. The ANOVA test was used to assess the significance of the model and its coefficients. The maximum pollutant conversion at 180 min (98.50%) was obtained with Fe = 7 mg L-1, HP = 305 mg L-1, and I = 0.12 W cm-2. The effect of two inorganic anions usually presents in real groundwater (bicarbonate and chloride, 600 mg L-1 each) was investigated under those optimized operating conditions. A slight reduction in the 124-TCB conversion after 180 min of reaction was noticed in the presence of bicarbonate (8.31%) and chloride (7.85%). Toxicity was studied with Microtox® (Azur Environmental, Carlsbad, CA, USA) bioassay, and a remarkable toxicity decrease was found in the treated samples, with the inhibition proportional to the remaining 124-TCB concentration. That means that nontoxic byproducts are produced in agreement with the high dechlorination degrees noticed.
Subject(s)
Chlorobenzenes/chemistry , Hydrogen Peroxide , Iron , Bicarbonates , Chlorides , Chlorobenzenes/analysis , Hydrogen Peroxide/chemistry , Hydrogen-Ion Concentration , Iron/chemistry , Oxalates , Oxidation-ReductionABSTRACT
Chlorinated organic compounds (COCs) are persistent organic pollutants often found in groundwater near industrial sites or in industrial wastewaters. Adsorption into activated carbon is a common strategy to remediate these waters, but spent activated carbon results in a toxic residue to manage. To avoid the transport of the chlorinated compounds out of the site, the in-situ regeneration of the spent activated carbon can be considered for reuse to implement a circular economy. In this work, the regeneration of a commercial granular activated carbon (GAC) has been carried out using thermally activated sodium persulfate (TAP). GAC was previously saturated in 1,2,4-trichlorobenzene (124-TCB) as the model compound. The initial adsorption value was 350 mg124-TCB·gGAC -1. First, the nonproductive consumption of sodium persulfate was studied at different temperatures using nonsaturated GAC. Then, the regeneration of the saturated GAC (5 g) was studied by an aqueous solution (166 mM) of TAP (1 L) at a temperature range from 20 to 80 °C. The possible recovery of the adsorption capacity was studied after 3 h of treatment in three successive adsorption-regeneration cycles at the selected temperature (60 °C). The physicochemical changes of the GAC were also investigated before and after the regeneration treatments. The results evidence the significant deposition of sulfate on the GAC after each treatment of regeneration, which avoids the recovery of the initial adsorption capacity. Therefore, each regeneration cycle was necessarily followed by a washing step at 60 °C to remove this sulfate. After that, the regeneration treatment achieved a stable and high recovery of the initial adsorption capacity of about 48.2%.
ABSTRACT
Surfactant enhanced aquifer remediation is a common treatment to remediate polluted sites with the inconvenience that the effluent generated must be treated. In this work, a complex mixture of chlorobenzene and dichlorobenzenes in a non-ionic surfactant emulsion has been carried out by volatilization. Since this techhnique is strongly affected by the presence of the surfactant, modifying the vapour pressure, Pv0, and activity coefficient, γ, a correlation between Pvj0γj and surfactant concentration and temperature was proposed for each compound, employing the Surface Response Methodology (RSM). Volatilization experiments were carried out at different temperatures and gas flow rates. A good agreement between experimental and predicted remaining SVCOCs during the air stripping process was obtained, validating the thermodynamic parameters obtained with RSM. Regarding the results of volatilization, at 60 °C 80% of SVCOCs were removed after 6 h, and the surfactant capacity was almost completely recovered so the solution can be recycled in soil flushing.
ABSTRACT
Sites polluted by dense non-aqueous phases (DNAPLs) constitute an environmental concern. In situ chemical oxidation (ISCO) application is limited since oxidation often occurs in the aqueous phase and contaminants are usually hydrophobic. In this work, ISCO enhanced by the surfactant addition (S-ISCO) was studied for a complex liquid mixture of chlorinated organic compounds (COCs) using persulfate (PS) activated by alkali (PSA) as oxidant and Emulse-3® as a commercial non-ionic surfactant. The reaction between E3 and PSA was investigated in the absence and presence of solubilized COCs in the following concentration ranges: COCs 1.2-50 mM, PS 84-336 mM, NaOH:PS molar ratio of 2, and surfactant concentration 1-10 g·L-1. In the experiments carried out in the absence of COCs, the unproductive consumption of PS was studied. The higher the surfactant concentration, the lower the ratio PS consumed to the initial surfactant concentration due to more complex micelle structures hindering the oxidation of surfactant molecules. This hindering effect was also noticed in the oxidation of solubilized COCs. The reduction of chlorobenzenes by PSA was negligible at surfactant concentrations above 2.5 g·L-1, independently of the COCs concentration solubilized. Instead, a surfactant concentration of about 1 and PS concentration of 168 mM yielded a significant decrease in the time required to abate a mass of DNAPL, compared with an ISCO process, with a bearable increase in the unproductive consumption of PS.
Subject(s)
Surface-Active Agents , Water Pollutants, Chemical , Alkalies , Chlorobenzenes , Organic Chemicals , Oxidation-Reduction , Sulfates , Water Pollutants, Chemical/analysisABSTRACT
Surfactant Enhanced In-Situ Chemical Oxidation (S-ISCO) is an emerging technology in the remediation of sites with residual Dense Non-Aqueous Phase Liquids (DNAPLs), a ubiquitous problem in the environment and a challenge to solve. In this work, three nonionic surfactants: E-Mulse3® (E3), Tween80 (T80), and a mixture of Tween80-Span80 (TS80), and an anionic surfactant: sodium dodecyl sulfate (SDS), combined with persulfate activated by alkali (PSA) as oxidant have been investigated to remove the DNAPL generated as liquid waste in lindane production, which is composed of 28 chlorinated organic compounds (COCs). Because the compatibility between surfactants and oxidants is a key aspect in the S-ISCO effectiveness the unproductive consumption of PS by surfactants was investigated in batch (up to 864â¯h) varying the initial concentration of PS (84-42â¯mmol·L-1) and surfactants (0-12â¯g·L-1) and the NaOH:PS molar ratio (1 and 2). The solubilization capacity of a partially oxidized surfactant was analyzed by estimating its Equivalent Surfactant Capacity, ESC, (as mmolCOCs dissolvedgsurf-1) and comparing it to the expected value for an unoxidized surfactant, ESCo. Finally, the abatement of DNAPL with simultaneous addition of surfactant and PSA was studied. At the conditions used, a negligible unproductive consumption of PS was found by SDS; meanwhile, PS consumption at 360â¯h ranged between 70 and 80% using the nonionic surfactants. The highest ratios of ESC/ESCo were found with SDS and E3 and these surfactants were chosen for the S-ISCO treatment. When oxidant and surfactant were simultaneously applied for DNAPL abatement the COC conversion was more than three times higher with E3 (0.6 at 360â¯h) than SDS. Moreover, it was obtained that the time needed for the removal of a mass of DNAPL by PSA in the absence of surfactants was notably higher than the time required when a suitable surfactant was added.
ABSTRACT
The intensive use of organochlorine pesticides, such as lindane (γ-HCH), and the inadequate management of their wastes, is a huge environmental problem. The lindane production during the last century has generated huge volumes of solid wastes of other HCH isomers, causing hot points of soil and groundwater contamination. The soil treated in this work was obtained from a landfill located in the nearby of an old lindane factory, containing α-HCH and ß-HCH as main contaminants. This study addresses for the first time the application of different chemical oxidation treatments, viz. Fenton process (H2O2â¯+â¯Fe), persulfate (PS) activated by temperature (20 and 40⯰C), by alkali (NaOH) and by the combination of alkali and temperature (NaOH, 40⯰C) for the remediation of HCH-polluted soils (CHCHsâ¯=â¯155â¯mgâ¯kg-1). The intrinsic characteristics of the soil (high carbonate content) led to high consumption of H2O2 (XH2O2â¯≈â¯100% at 24â¯h) and complete iron precipitation, making unappropriated the application of the Fenton process. The efficiency of thermal PS was limited by the low solubility of HCH isomers in the aqueous phase, the high refractoriness of these compounds towards oxidation, and the presence of the contaminants in the form of particulate matter. After 25â¯days of treatment, a conversion of chlorinated organic compounds (COCs) of 50% was achieved (VL/Wsoilâ¯=â¯2, CPSâ¯=â¯40â¯gâ¯L-1, 40⯰C), whereas the application of PS activated by alkali and temperature (40⯰C) led to promising results. At pH above 12, HCHs were dehydrochlorinated to trichlorobenzenes, which were further oxidized by hydroxyl radicals. The hydrolysis rate of ß-HCH was the limiting step of the process, and it was favored by increasing the reaction temperature. At 40⯰C, a conversion of COCs above 95% was achieved (VL/Wsoilâ¯=â¯2, CPSâ¯=â¯40â¯gâ¯L-1, CNaOHâ¯=â¯13.5â¯gâ¯L-1, 14â¯days) with low oxidant consumption (XPSâ¯=â¯30%).
ABSTRACT
Application of surfactants in the remediation of polluted sites with dense nonaqueous phase liquid (DNAPL) still requires knowledge of partitioning between surfactants and pollutants in the organic and aqueous phases and the time necessary to reach this balance. Two real DNAPLs, generated as wastes in the lindane production and taken from the polluted sites from Sabiñanigo (Spain), were used for investigating the solubilization of 28 chlorinated organic compounds (COCs) applying aqueous surfactant solutions of three nonionic surfactants (E-Mulse® 3 (E3), Tween®80 (T80), and a mixture of Tween®80-Span®80 (TS80)) and an anionic surfactant (sodium dodecyl sulfate (SDS)). The initial concentrations of surfactants were tested within the range of 3-17 g·L-1. The pH was also modified from 7 to >12. The uptake of nonionic surfactants into the organic phase was higher than the anionic surfactants. Solubilization of COCs with the nonionic surfactants showed similar molar solubilization ratios (MSR = 4.33 mmolCOCs·g-1surf), higher than SDS (MSR = 0.70 mmolCOCs·g-1SDS). Furthermore, under strong alkaline conditions, the MSR value of the nonionic surfactants was unchanged, and the MSR of SDS value increased (MSR = 1.32 mmolCOCs·g-1SDS). The nonionic surfactants did not produce preferential solubilization of COCs; meanwhile, SDS preferentially dissolved the more polar compounds in DNAPL. The time required to reach phase equilibrium was between 24 and 48 h, and this contact time should be assured to optimize the effect of the surfactant injected on COC solubilization.
Subject(s)
Hexachlorocyclohexane , Surface-Active Agents , Hydrogen-Ion Concentration , Sodium Dodecyl Sulfate , SolubilityABSTRACT
Chlorinated pesticides were extensively produced in the XX century, generating high amounts of toxic wastes often dumped in the surroundings of the production sites, resulting in hot points of soil and groundwater pollution worldwide. This is the case of Bailín landfill, located in Sabiñánigo (Spain), where groundwater is highly polluted with chlorobenzenes (mono, di, tri and tetra) and hexachlorocyclohexanes. This study addresses the abatement of chlorinated organic compounds (COCs) present in the groundwater coming from the Bailín landfill by thermally activated persulfate, PS (TAP). The influence of temperature (30-50 °C) and oxidant concentration (2-40 g L-1) on the efficiency of COCs (initial concentration of COCs = 57.53 mg L-1, determined by the solubility of the pollutants in water) degradation has been investigated. Raising the reaction temperature and PS concentration the degradation of COCs significantly accelerates, as a result of higher production of sulfate radicals. The thermal activation of PS implies side reactions, involving the unproductive decomposition of this oxidant. The activation energy calculated for this reaction (128.48 kJ mol-1) reveals that is slightly more favored by temperature than the oxidation of COCs by sulfate radicals (102.4-115.72 kJ mol-1). At the selected operating conditions (PS = 10 g L-1, 40 °C), the almost complete conversion of COCs and a dechlorination and mineralization degree above 80% were obtained at 168 h reaction time. A kinetic model, able to adequately predict the experimental concentration of COCs when operating at different temperatures and initial concentration of PS has been proposed.
Subject(s)
Groundwater , Water Pollutants, Chemical , Organic Chemicals , Oxidation-Reduction , Sulfates , Waste Disposal FacilitiesABSTRACT
In this study, we investigate the performance of a Fenton-like process carried out adding as amendments humic acids extracted from compost obtained from organic wastes. Namely, Fenton-like lab-scale tests with different dosages of the extracted humic acids and traditional stabilizing agent (KH2PO4) were performed on a diesel-contaminated soil collected in a former gasoline station. The performed tests showed a beneficial effect of the extracted humic acids on the hydrogen peroxide stability. Namely, the H2O2 lifetime in the tests carried out without the addition of any amendments proved to be quite limited, resulting equal to around 1 h. The adoption of the extracted humic acids alone entailed a limited increase of the hydrogen peroxide stability that anyhow was detected in solution for 24 h using 10 g/L of extracted HA. When the humic acids (10 g/L) were used in combination with KH2PO4 (8.2 g/L), the hydrogen peroxide lifetime increased up to around 150 h. A beneficial effect of the humic acids extracted from compost for a Fenton-like process was also observed in terms of diesel removal. Namely, without any amendment, a contaminant removal of around 55% was observed. Using KH2PO4 or HA alone, the contaminant removal raised up to around 75% while using the traditional stabilizer together with the humic acids extracted from compost, it was possible to remove up to 90% of the initial diesel content of the soil.
Subject(s)
Composting , Soil Pollutants/analysis , Humic Substances/analysis , Hydrogen Peroxide , SoilABSTRACT
Treatment of polluted wastewaters from industrial activities has become a source of major concern for the environment. In this work, real wastewater from a physico-chemical (WWFQ) treatment was tested through different oxidation technologies: Fenton and Fenton-like reagent and persulfate activated by NaOH and Fe(II). Oxidation reactions with Fenton's reagent were carried out in a 0.25 L batch reactor at 25 °C by adding either Fe(II) or Fe(III) and H2O2 to an aqueous solution of wastewater, whose pH was previously adjusted to 2 or 3. Iron concentration ranging from 25 to 100 mg/L and peroxide concentration from 2500 to 10000 mg/L were used. The total organic carbon slightly decreased when WWFQ was treated. Moreover, better results were obtained when Fe(II) was used than Fe(III). Both iron concentration and oxidant dosage had a positive influence on the chemical oxygen demand (COD) removal, until an asymptotic value of 30% was obtained. Oxidation of pollutants contained in WWFQ was studied with persulfate (18.4-294 mM) activated with NaOH and Fe(II) (36.8-588 mM). Again, a positive influence of both persulfate and NaOH was observed, although a similar asymptotic COD value was observed. This parallelism between both technologies confirms recalcitrant compounds were obtained.
Subject(s)
Wastewater , Water Pollutants, Chemical , Ferric Compounds , Ferrous Compounds , Hydrogen Peroxide , Oxidation-Reduction , Sodium Hydroxide , Waste Disposal, FluidABSTRACT
Hexachlorocyclohexane (HCH) and mainly the γ-HCH isomer, namely lindane, were extensively produced and used as pesticides. Huge amounts of wastes, solids and liquids, were disposed of in the surroundings of the production sites. The liquid residuum was a complex mixture of chlorinated organic compounds, COCs, from chlorobenzene to heptachlorocyclohexane. This Dense Non-Aqueous Phase Liquid, DNAPL, migrated by density through the subsurface to greater depths, being trapped or adsorbed into the soil in this movement posing a significant risk to the groundwater. Knowledge of the partitioning in water of COCs in DNAPL is a key issue to determine its fate in the environment. However, there are no data in literature for the partitioning and/or solubility of many of the COCs in this DNAPL, such as pentachlorocyclohexene, hexachlorocyclohexene and heptachlorocyclohexane despite them constitute about 13-30% of the mole fraction of the DNAPLs. In this work, the partitioning to water of COCs in free and those adsorbed onto soil has been studied. In addition, measured and predicted aqueous concentrations of each COC in the DNAPL mixture have been compared. To do this, the solubility of a compound that is a solid crystal when pure at Pâ¯=â¯298â¯K and Pâ¯=â¯1â¯atm has been evaluated considering the approach of sub-cooled liquid state of solid organochlorines. Samples were obtained at Sabiñanigo landfills and soils used had several grain sizes. Transformation in alkaline media of COCs had a positive environmental impact.