ABSTRACT
Perovskite/organic tandem solar cells (PO-TSCs) demonstrate exceptional suitability for emerging applications such as building-integrated photovoltaics, wearable devices, and greenhouse farming. By leveraging the distinctive attributes of perovskite and organic materials, which encompass expanded solar spectrum utilization, chemically benign solubility, and soft nature, PO-TSCs position themselves as ideal candidates for high-performance semi-transparent photovoltaics (ST-PVs). Despite these advantages, their development significantly lags behind other perovskite-based counterparts, such as perovskite/perovskite, perovskite/silicon, and perovskite/Cu(In, Ga)Se2. To address existing challenges and unlock the full potential of PO-TSCs, an exploration of the fundamental mechanisms governing tandem photovoltaic devices is embarked. Delving into critical aspects such as charge generation/separation, energy level alignment, and material choices becomes pivotal for optimizing PO-TSC performance. The investigation of monolithic two-terminal PO-TSCs offers insights into achievements and barriers, recognizing the competitive landscape with other TSC counterparts. Further scrutiny of perovskite absorbers and organic absorbers in TSCs reveals strategies aimed at enhancing stability and efficiency. The discussion extends to interconnection layers, elucidating their role in optimizing light transmission and balancing carrier recombination. In conclusion, a compelling outlook on the dynamic landscape of PO-TSCs is presented, highlighting the remarkable efficiency progression and signaling their potential to revolutionize solar energy harvesting technologies.
ABSTRACT
All-polymer solar cells (all-PSCs) have drawn growing attention and achieved tremendous progress recently, but their power conversion efficiency (PCE) still lags behind small-molecule-acceptor (SMA)-based PSCs due to the relative difficulty on morphology control of polymer photoactive blends. Here, low-cost PTQ10 is introduced as a second polymer donor (a third component) into the PM6:PY-IT blend to finely tune the energy-level matching and microscopic morphology of the polymer blend photoactive layer. The addition of PTQ10 decreases the π-π stacking distance, and increases the π-π stacking coherence length and the ordered face-on molecular packing orientation, which improves the charge separation and transport in the photoactive layer. Moreover, the deeper highest occupied molecular orbital energy level of the PTQ10 polymer donor than PM6 leads to higher open-circuit voltage of the ternary all-PSCs. As a result, a PCE of 16.52% is achieved for ternary all-PSCs, which is one of the highest PCEs for all-PSCs. In addition, the ternary devices exhibit a high tolerance of the photoactive layer thickness with high PCEs of 15.27% and 13.91% at photoactive layer thickness of ≈205 and ≈306 nm, respectively, which are the highest PCEs so far for all-PSCs with a thick photoactive layer.
ABSTRACT
Polymer solar cells (PSCs) have achieved great progress recently, benefiting from the rapid development of narrow bandgap small molecule acceptors and wide bandgap conjugated polymer donors. Among the polymer donors, the D-A copolymers with quinoxaline (Qx) as A-unit have received increasing attention since the report of the low-cost and high-performance D-A copolymer donor based on thiophene D-unit and difluoro-quinoxalline A-unit in 2018. In addition, the weak electron-deficient characteristic and the multiple substitution positions of the Qx unit make it an ideal A-unit in constructing the wide bandgap polymer donors with different functional substitutions. In this review article, recent developments of the Qx-based D-A copolymer donors, including synthetic method of the Qx unit, backbone modulation, side chain optimization, and functional substitution of the Qx-based D-A copolymers, are summarized and discussed. Furthermore, the application of the Qx-based D-A copolymers as hole transport material in perovskite solar cells (pero-SCs) is also introduced. The focus mainly on the molecular design strategies and structure-properties relationship of the Qx-based D-A copolymers, aiming to provide a guideline for developing high-performance Qx-based D-A copolymers for the applications as donor in PSCs and as hole transport material in pero-SCs.
ABSTRACT
To reduce synthetic cost of the classic fluorinated bithienyl benzodithiophene (BDTT-F) unit, here, an alpha-fluorinated bithienyl benzodithiophene unit, namely, α-BDTT-F (F atom in the α position of the lateral thiophene unit), is developed by the isomerization strategy of exchanging the positions of the F atom and flexible alkyl chain on the lateral thiophene unit of the BDTT-F unit. The α-BDTT-F unit was synthesized with less synthetic steps, higher synthetic yield, and less purification times from the same raw materials as those of the BDTT-F unit, thus with low synthetic cost. Theoretical calculation indicates that the α-BDTT-F unit possesses a similar twisted conformation and electronic structures as those of the BDTT-F unit. The α-BDTT-F-based polymer α-PBQ10 exhibits similar light absorption and energy levels as those of the corresponding BDTT-F-based polymer PBQ10 but marginally increased molecular aggregation and stronger hole transport than PBQ10. In consequence, the α-PBQ10:Y6-based polymer solar cell demonstrates a slightly enhanced power conversion efficiency (PCE) of 16.26% compared with that of the PBQ10:Y6-based device (PCE = 16.23%). Also, the PCE is further improved to 16.77% through subtle microscopic morphology regulation of the photoactive layer with the fullerene derivative indene-C60 bisadduct as the third component. This work provides new ideas for the design of low-cost and high-efficiency photovoltaic molecules.
ABSTRACT
In organic photovoltaic (OPV) blends, photogenerated excitons dissociate into charge-separated electrons and holes at donor/acceptor interfaces. The bimolecular recombination of spin-uncorrelated electrons and holes may cause nonradiative loss by forming the low-lying triplet excited states (T1) via the intermediate charge-transfer triplet states. Here, we show that such a spin-related loss channel can be suppressed in the OPV blends with fluorinated nonfullerene acceptors (NFAs). By combining ultrafast optical spectroscopy and triplet sensitization measurements, the T1 states at the acceptors have been observed to generate from the charge-separated electrons and holes in the OPV blends with a same polymer donor and two sets of NFAs with and without fluorination. The triplet formation is largely suppressed and the lifetime of charge carrier is markedly prolonged in the blends with fluorinated NFAs. The fluorination effect on the charge dynamics can be ascribed to the modified energy alignment between the triplet excited states of charge-transfer and locally excited characters as supported by quantum chemical computation. Our findings explain the mechanism responsible for the improved photocurrent generation in the OPV blends with fluorinated NFAs, suggesting that manipulating the energy landscape of triplet excited states is a promising strategy for further optimizing OPV devices.
ABSTRACT
In order to achieve the electrospinning of chitosan in common organic solvents, amino-reserved CS-g-PCL was synthesized by one-step method. PLLA and dichloromethane/ethanol (CH2Cl2/EtOH) solvent were chosen to prepare a series of different compositions of PLLA/CS-g-PCL mats (8/2, 6/4, 4/6, 2/8 wt/wt%) by electrospinning. The SEM showed that the smooth defect-free and uniform nanofibers were collected except PLLA/CS-g-PCL 2/8 and pure CS-g-PCL, and the fiber diameter was decreased from 828 nm to 461 nm with the increasing content of CS-g-PCL. The mechanical properties of composite mats have decreased with increasing CS-g-PCL content, but much higher than neat PLLA. The water contact angle, water absorption rate, water-vapor transmission rate and in vitro degradation behavior were 129°-19°, 109%-482%, 1945-2517 g m-2 day-1 and 4-14%, respectively. The addition of CS-g-PCL imparted PLLA/CS-g-PCL electrospun mats on better properties, improving the nature defects of PLLA. The in vitro cell culture studies showed that PLLA/CS-g-PCL 6/4 exhibited a higher in vitro biocompatibility and a better ability for cell attachment, spreading, and proliferation, comparing with PLLA mats. Herein, PLLA/CS-g-PCL 6/4 electrospun mats with excellent performance, was considered the potential application as wound dressing in skin tissue engineering.
Subject(s)
Biocompatible Materials/chemistry , Chitosan/chemistry , Nanofibers/chemistry , Polyesters/chemistry , Water/chemistry , Animals , Cell Line , Cell Proliferation/drug effects , Fibroblasts/drug effects , Magnetic Resonance Spectroscopy , Materials Testing , Mice , Nanofibers/ultrastructure , Polyesters/chemical synthesis , Porosity , Solubility , Spectroscopy, Fourier Transform Infrared , Surface Properties , Temperature , X-Ray DiffractionABSTRACT
In organic solar cells (OSCs), cathode interfacial materials are generally designed with highly polar groups to increase the capability of lowering the work function of cathode. However, the strong polar group could result in a high surface energy and poor physical contact at the active layer surface, posing a challenge for interlayer engineering to address the trade-off between device stability and efficiency. Herein, we report a hydrogen-bonding interfacial material, aliphatic amine-functionalized perylene-diimide (PDINN), which simultaneously down-shifts the work function of the air stable cathodes (silver and copper), and maintains good interfacial contact with the active layer. The OSCs based on PDINN engineered silver-cathode demonstrate a high power conversion efficiency of 17.23% (certified value 16.77% by NREL) and high stability. Our results indicate that PDINN is an effective cathode interfacial material and interlayer engineering via suitable intermolecular interactions is a feasible approach to improve device performance of OSCs.
ABSTRACT
A low-cost and high-performance bulk heterojunction (BHJ) solar cell comprising an emerging polymer donor, poly[(thiophene)-alt-(6,7-difluoro-2-(2-hexyldecyloxy)quinoxaline)] (PTQ10), shows an efficiency of 12.7%. To improve the performance of the solar cells, a better understanding of the structure-property relationships of the PTQ10-based devices is crucial. Here, we fabricate PTQ10/nonfullerene and fullerene BHJ devices, including PTQ10/IDIC, PTQ10/ITIC, and PTQ10/PC71BM, processed with or without thermal annealing and additive and provide detailed descriptions of the relationships between the morphology and performance. PTQ10 is found to be highly miscible with nonfullerene IDIC and ITIC acceptors and poorly miscible with fullerene PC71BM acceptors. Thermal annealing promotes the crystallization of PTQ10 and phase separation of all PTQ10/IDIC, PTQ10/ITIC, and PTQ10/PC71BM devices, leading to an increased power conversion efficiencies (PCEs) of the PTQ10/IDIC and PTQ10/ITIC devices but a decreased PCE of PTQ10/PC71BM devices with 1,8-di-iodooctane (DIO) additive. Without thermal annealing, DIO greatly improves the morphology of PTQ10/PC71BM, leading to a higher PCE. The results show that the degree of phase separation and ordering in the PTQ10-based devices significantly influences device performance. The morphology-property correlations demonstrated will assist in the rational design of these low-cost polymer donor-based solar cells to achieve even higher performance.
ABSTRACT
Achieving efficient charge transfer at small frontier molecular orbital offsets between donor and acceptor is crucial for high performance polymer solar cells (PSCs). Here we synthesize a new wide band gap polymer donor, PTQ11, and a new low band gap acceptor, TPT10, and report a high power conversion efficiency (PCE) PSC (PCE = 16.32%) based on PTQ11-TPT10 with zero HOMO (the highest occupied molecular orbital) offset (ΔEHOMO(D-A)). TPT10 is a derivative of Y6 with monobromine instead of bifluorine substitution, and possesses upshifted lowest unoccupied molecular orbital energy level (ELUMO) of -3.99 eV and EHOMO of -5.52 eV than Y6. PTQ11 is a derivative of low cost polymer donor PTQ10 with methyl substituent on its quinoxaline unit and shows upshifted EHOMO of -5.52 eV, stronger molecular crystallization, and better hole transport capability in comparison with PTQ10. The PSC based on PTQ11-TPT10 shows highly efficient exciton dissociation and hole transfer, so that it demonstrates a high PCE of 16.32% with a higher Voc of 0.88 V, a large Jsc of 24.79 mA cm-2, and a high FF of 74.8%, despite the zero ΔEHOMO(D-A) value between donor PTQ11 and acceptor TPT10. The PCE of 16.32% is one of the highest efficiencies in the PSCs. The results prove the feasibility of efficient hole transfer and high efficiency for the PSCs with zero ΔEHOMO(D-A), which is highly valuable for understanding the charge transfer process and achieving high PCE of PSCs.
ABSTRACT
Four low-cost copolymer donors of poly(thiophene-quinoxaline) (PTQ) derivatives are demonstrated with different fluorine substitution forms to investigate the effect of fluorination forms on charge separation and voltage loss (Vloss ) of the polymer solar cells (PSCs) with the PTQ derivatives as donor and a A-DA'D-A-structured molecule Y6 as acceptor. The four PTQ derivatives are PTQ7 without fluorination, PTQ8 with bifluorine substituents on its thiophene D-unit, PTQ9, and PTQ10 with monofluorine and bifluorine substituents on their quinoxaline A-unit respectively. The PTQ8- based PSC demonstrates a low power conversion efficiency (PCE) of 0.90% due to the mismatch in the highest occupied molecular orbital (HOMO) energy levels alignment between the donor and acceptor. In contrast, the devices based on PTQ9 and PTQ10 show enhanced charge-separation behavior and gradually reduced Vloss , due to the gradually reduced nonradiative recombination loss in comparison with the PTQ7-based device. As a result, the PTQ10-based PSC demonstrates an impressive PCE of 16.21% with high open-circuit voltage and large short-circuit current density simultaneously, and its Vloss is reduced to 0.549 V. The results indicate that rational fluorination of the polymer donors is a feasible method to achieve fast charge separation and low Vloss simultaneously in the PSCs.
ABSTRACT
The application of polymer solar cells (PSCs) with n-type organic semiconductor as acceptor requires further improving powder conversion efficiency, increasing stability and decreasing cost of the related materials and devices. Here we report a simplified synthetic route for 4,4,9,9-tetrahexyl-4,9-dihydro-s-indaceno [1,2-b:5,6-b'] dithiophene by using the catalyst of amberlyst15. Based on this synthetic route and methoxy substitution, two low cost acceptors with less synthetic steps, simple post-treatment and high yield were synthesized. In addition, the methoxy substitution improves both yield and efficiency. The high efficiency of 13.46% was obtained for the devices with MO-IDIC-2F (3,9-bis(2-methylene-5 or 6-fluoro-(3-(1,1-dicyanomethylene)-indanone)-4,4,9,9-tetrahexyl-5,10-dimethoxyl-4,9-dihydro-s-indaceno[1,2-b:5,6-b'] dithiophene) as acceptor. Based on the cost analysis, the PSCs based on MO-IDIC-2F possess the great advantages of low cost and high photovoltaic performance in comparison with those PSCs reported in literatures. Therefore, MO-IDIC-2F will be a promising low cost acceptor for commercial application of PSCs.
ABSTRACT
Herein, we investigated a series of fullerene-free organic solar cells (OSCs) based on six different donor:acceptor (D:A) blends with varied highest occupied molecular orbital (HOMO) offsets from -0.05 to 0.21 eV. First, to verify the energetic compatibility of a specific D:A pair, especially for HOMO offsets, we established a simple method to estimate the hole transfer tendencies between D and A by using bilayer hole-only devices. It reveals that the asymmetrical diode effect of the bilayer hole-only devices can correlate with the FF and Jsc of the relevant OSCs. Second, to find out whether HOMO offset is the main restriction of hole transfer, we measured transient absorption spectra and examined the hole transfer behavior in the blends, revealing that the occurrence of hole transfer is independent of the HOMO offsets and ultrafast in the time scale of ≤4.6 ps for those blends with ≥0 eV HOMO offsets. In contrast, a negative HOMO offset can significantly slow down the hole transfer with a half-time of â¼400 ps. Furthermore, we compare the device parameters under varied light intensities and discover that the bimolecular recombination should be one of the main restrictions for high device performance. Surprisingly, small HOMO offsets of 0 and 0.06 eV can also enable high PCEs of 10.42% and 11.75% for blend 2 (PTQ10:HC-PCIC) and blend 3 (PBDB-TF:HC-PCIC), respectively. Overall, our work demonstrates not only the validity of high-performance OSCs operating at the near zero HOMO offsets but also the charge dynamic insights of these blends, which will help gain understanding on the further improvement of OSCs.
ABSTRACT
The precise control of stoichiometric balance and ionic defects on the surface of solution-processed perovskite is critical to the performance and stability of perovskite solar cells (pero-SCs). Here, we introduce a low-cost and stable conjugated donor polymer (PTQ10) as interfacial layer in the planar n-i-p structured pero-SCs. The polymer was applied to the perovskite intermediate phase before the thermal annealing. This treatment significantly reduced the loss of surface organic cation during thermal annealing. Importantly, the kinetics of phase conversion of perovskite was influenced, and perovskite crystal showed a more preferential orientation. Moreover, the polymer proved to be an effective hole extraction layer due to the proper energy alignment with perovskite. Finally, a champion power conversion efficiency of the planar pero-SCs was achieved at 21.2% with a high fill factor of 81.6%. The devices also showed great ambient and thermal stability. This work presents a facile way of perovskite surface control to achieve high-performance pero-SCs.
ABSTRACT
Two benzothiadiazole (BT)-based small-molecule donors, SM-BT-2OR with alkoxy side chain and SM-BT-2F with fluorine atom substitution, were designed and synthesized for investigating the effect of the substituents on the photovoltaic performance of the donor molecules in all small molecule organic solar cells (SM-OSCs). Compared to SM-BT-2OR, the film of SM-BT-2F exhibited red-shifted absorption and deeper HOMO level of -5.36 eV. When blending with n-type organic semiconductor (n-OS) acceptor IDIC, the as-cast devices displayed similar PCE values of 2.33 and 2.76% for the SM-BT-2OR and SM-BT-2F-based devices, respectively. The SM-BT-2OR-based devices with thermal annealing (TA) at 120°C for 10 min showed optimized PCE of 7.20%, however, the SM-BT-2F-based device displayed lower PCE after the TA treatment, which should be ascribed to the undesirable morphology and molecular orientation. Our results reveal that for the SM-OSCs, the substituent groups of small molecule donors have great impact on the film morphology, as well as the photovoltaic performance.
ABSTRACT
Two medium-bandgap p-type organic small molecules H21 and H22 with an alkylsily-thienyl conjugated side chain on benzo[1,2-b:4,5-b']dithiophene central units are synthesized and used as donors in all-small-molecule organic solar cells (SM-OSCs) with a narrow-bandgap n-type small molecule 2,2'-((2Z,2'Z)-((4,4,9,9-tetrahexyl-4,9-dihydro-s-indaceno[1,2-b:5,6-b']dithiophene-2,7-diyl)bis(methanylylidene))bis(3-oxo-2,3-dihydro-1H-indene-2,1-diylidene))dimalononitrile (IDIC) as the acceptor. In comparison to H21 with 3-ethyl rhodanine as the terminal group, H22 with cyanoacetic acid esters as the terminal group shows blueshifted absorption, higher charge-carrier mobility and better 3D charge pathway in blend films. The power conversion efficiency (PCE) of the SM-OSCs based on H22:IDIC reaches 10.29% with a higher open-circuit voltage of 0.942 V and a higher fill factor of 71.15%. The PCE of 10.29% is among the top efficiencies of nonfullerene SM-OSCs reported in the literature to date.
ABSTRACT
The application of polymer solar cells requires the realization of high efficiency, high stability, and low cost devices. Here we demonstrate a low-cost polymer donor poly[(thiophene)-alt-(6,7-difluoro-2-(2-hexyldecyloxy)quinoxaline)] (PTQ10), which is synthesized with high overall yield of 87.4% via only two-step reactions from cheap raw materials. More importantly, an impressive efficiency of 12.70% is obtained for the devices with PTQ10 as donor, and the efficiency of the inverted structured PTQ10-based device also reaches 12.13% (certificated to be 12.0%). Furthermore, the as-cast devices also demonstrate a high efficiency of 10.41% and the devices exhibit insensitivity of active layer thickness from 100 nm to 300 nm, which is conductive to the large area fabrication of the devices. In considering the advantages of low cost and high efficiency with thickness insensitivity, we believe that PTQ10 will be a promising polymer donor for commercial application of polymer solar cells.
ABSTRACT
The oligomer of ß-amyloid (Aß) is considered the main neurotoxin in Alzheimer's disease (AD). Therefore, the inhibition of the formation of Aß oligomer could be a target for AD therapy. In this study, with the help of the dot blotting assay and transmission electronic microscopy, it was have discovered that 5-hydroxycyclopenicillone, a cyclopentenone recently isolated from a sponge-associated fungus, effectively reduced the formation of Aß oligomer from Aß peptide in vitro. Molecular dynamics simulations suggested hydrophobic interactions between 5-hydroxycyclopenicillone and Aß peptide, which might prevent the conformational transition and oligomerization of Aß peptide. Moreover, Aß oligomer pre-incubated with 5-hydroxycyclopenicillone was less toxic when added to neuronal SH-SY5Y cells compared to the normal Aß oligomer. Although 5-hydroxycyclopenicillone is not bioavailable in the brain in its current form, further modification or encapsulation of this chemical might improve the penetration of 5-hydroxycyclopenicillone into the brain. Based on the current findings and the anti-oxidative stress properties of 5-hydroxycyclopenicillone, it is suggested that 5-hydroxycyclopenicillone may have potential therapeutic efficacy in treating AD.
Subject(s)
Amyloid beta-Peptides/antagonists & inhibitors , Cyclopentanes/chemistry , Cyclopentanes/pharmacology , Neurons/drug effects , Neuroprotective Agents/pharmacology , Alzheimer Disease/drug therapy , Cell Line, Tumor , Cell Survival/drug effects , Fungi/chemistry , Humans , Molecular Dynamics Simulation , Neurons/pathology , Neuroprotective Agents/chemistry , Neuroprotective Agents/therapeutic useABSTRACT
Suppression of carrier recombination is critically important in realizing high-efficiency polymer solar cells. Herein, it is demonstrated difluoro-substitution of thiophene conjugated side chain on donor polymer can suppress triplet formation for reducing carrier recombination. A new medium bandgap 2D-conjugated D-A copolymer J91 is designed and synthesized with bi(alkyl-difluorothienyl)-benzodithiophene as donor unit and fluorobenzotriazole as acceptor unit, for taking the advantages of the synergistic fluorination on the backbone and thiophene side chain. J91 demonstrates enhanced absorption, low-lying highest occupied molecular orbital energy level, and higher hole mobility, in comparison with its control polymer J52 without fluorination on the thiophene side chains. The transient absorption spectra indicate that J91 can suppress the triplet formation in its blend film with n-type organic semiconductor acceptor m-ITIC (3,9-bis(2-methylene-(3-(1,1-dicyanomethylene)-indanone)-5,5,11,11-tetrakis(3-hexylphenyl)-dithieno[2,3-d:2,3'-d']-s-indaceno[1,2-b:5,6-b']-dithiophene). With these favorable properties, a higher power conversion efficiency of 11.63% with high VOC of 0.984 V and high JSC of 18.03 mA cm-2 is obtained for the polymer solar cells based on J91/m-ITIC with thermal annealing. The improved photovoltaic performance by thermal annealing is explained from the morphology change upon thermal annealing as revealed by photoinduced force microscopy. The results indicate that side chain engineering can provide a new solution to suppress carrier recombination toward high efficiency, thus deserves further attention.
ABSTRACT
In the last two years, polymer solar cells (PSCs) developed quickly with n-type organic semiconductor (n-OSs) as acceptor. In contrast, the research progress of nonfullerene organic solar cells (OSCs) with organic small molecule as donor and the n-OS as acceptor lags behind. Here, we synthesized a D-A structured medium bandgap organic small molecule H11 with bithienyl-benzodithiophene (BDTT) as central donor unit and fluorobenzotriazole as acceptor unit, and achieved a power conversion efficiency (PCE) of 9.73% for the all organic small molecules OSCs with H11 as donor and a low bandgap n-OS IDIC as acceptor. A control molecule H12 without thiophene conjugated side chains on the BDT unit was also synthesized for investigating the effect of the thiophene conjugated side chains on the photovoltaic performance of the p-type organic semiconductors (p-OSs). Compared with H12, the 2D-conjugated H11 with thiophene conjugated side chains shows intense absorption, low-lying HOMO energy level, higher hole mobility and ordered bimodal crystallite packing in the blend films. Moreover, a larger interaction parameter (χ) was observed in the H11 blends calculated from Hansen solubility parameters and differential scanning calorimetry measurements. These special features combined with the complementary absorption of H11 donor and IDIC acceptor resulted in the best PCE of 9.73% for nonfullerene all small molecule OSCs up to date. Our results indicate that fluorobenzotriazole based 2D conjugated p-OSs are promising medium bandgap donors in the nonfullerene OSCs.