One-Pot Modular Synthesis of Functionalized RAFT Agents Derived from a Single Thiolactone Precursor.

In this paper, the straightforward preparation of a range of functionalized trithiocarbonates as RAFT chain transfer agents (CTAs) is presented. The crucial step in the one-pot, three-step reaction sequence is the aminolysis of a thiolactone precursor as it introduces the desired functional handle (double bond, hydroxyl, furan, protected amine, ...) and generates the corresponding thiol in situ, facilitating further elaboration of the CTA. Furthermore, the newly synthesized trithiocarbonates were positively evaluated as mediators in the RAFT polymerization of styrene, isobornyl acrylate, and N-isopropylacrylamide, while the presence of the end groups in the heterotelechic polymers was confirmed by NMR and UV-vis analysis.

Structurally diverse polyamides obtained from monomers derived via the ugi multicomponent reaction.

The combination of the Ugi four-component reaction (Ugi-4CR) with acyclic diene metathesis (ADMET) or thiol-ene polymerization led to the formation of poly-1-(alkylcarbamoyl) carboxamides, a new class of substituted polyamides with amide moieties in the polymer backbone, as well as its side chains. 10-Undecenoic acid, obtained by pyrolysis of ricinoleic acid, the main fatty acid of castor oil, was used as the key renewable building block. The use of different primary amines, as well as isonitriles (isocyanides) for the described Ugi reactions provided monomers with high structural diversity. Furthermore, the possibility of versatile post-modification of functional groups in the side chains of the corresponding polymers should be of considerable interest in materials science. The obtained monomers were polymerized by ADMET, as well as thiol-ene, chemistry and all polymers were fully characterized. Finally, ortho-nitrobenzylamide-containing polyamides obtained by this route were shown to be photoresponsive and exhibited a dramatic change of their properties upon irradiation with light.

Renewable polyethylene mimics derived from castor oil.

An increasing number of reports on the syntheses of carbohydrate- and plant oil-based polymers has been published in ongoing efforts to produce plastic materials from renewable resources. Although many of these polymers are biodegradable and this is a desirable property for certain applications, in some cases non-degradable polymers are needed for long-term use purposes. Polyolefins are one of the most important classes of materials that have already taken their places in our daily life. On the other hand, their production relies on fossil resources. Therefore, within this contribution, we discuss synthetic routes toward a number of polyethylene mimics derived from fatty acids via thiol-ene and ADMET polymerization reactions in order to establish more sustainable routes toward this important class of polymers. Two different diene monomers were thus prepared from castor oil derived platform chemicals, their polymerization via the two mentioned routes was optimized and compared to each other, and their thermal properties were investigated.

About the activity and selectivity of less well-known metathesis catalysts during ADMET polymerizations.

We report on the catalytic activity of commercially available Ru-indenylidene and "boomerang" complexes C1, C2 and C3 in acyclic diene metathesis (ADMET) polymerization of a fully renewable α,ω-diene. A high activity of these catalysts was observed for the synthesis of the desired renewable polyesters with molecular weights of up to 17000 Da, which is considerably higher than molecular weights obtained using the same monomer with previously studied catalysts. Moreover, olefin isomerization side reactions that occur during the ADMET polymerizations were studied in detail. The isomerization reactions were investigated by degradation of the prepared polyesters via transesterification with methanol, yielding diesters. These diesters, representing the repeat units of the polyesters, were then quantified by GC-MS.

Fatty Acid Derived Monomers and Related Polymers Via Thiol-ene (Click) Additions.

Thiol-ene additions of methyl 10-undecenoate, a castor oil derived renewable platform chemical, were studied with the goal of preparing a set of renewable monomers. Good to excellent yields were obtained for these solvent and initiator free thiol-ene additions. The resulting monomers were then polymerized using TBD as a catalyst, to linear as well as hyperbranched polyesters that also contain thio-ether linkages. All thus prepared polymers were fully characterized (NMR, GPC, DSC, and TGA) and the results of these investigations will be discussed within this contribution. The thermal analysis of these polymers revealed melting points in the range from 50 to 71 °C. Moreover, no significant weight loss was observed below 300 °C.