ABSTRACT
This study aimed to evaluate the micro-mechanical and macro-mechanical properties of self-cured and light-cured alkasite and to investigate how accelerated degradation in acidic, alkaline, and ethanol solutions affects the macro-mechanical properties of self-cured and light-cured alkasite. The specimens of the alkasite material (Cention Forte, Ivoclar Vivadent) were prepared according to the following three curing modes: (1) light-cured immediately, (2) light-cured after a 5-min delay, and (3) self-cured. Microhardness was tested before and after immersion in absolute ethanol to indirectly determine crosslink density, while flexural strength and flexural modulus were measured using a three-point bending test after accelerated aging in the following solutions: (1) lactic acid solution (pH = 4.0), (2) NaOH solution (pH = 13.0), (3) phosphate-buffered saline solution (pH = 7.4), and (4) 75% ethanol solution. The data were statistically analyzed using a two-way ANOVA and Tukey post hoc test. The results showed that the microhardness, flexural strength, and flexural modulus were significantly lower in self-cured specimens compared to light-cured specimens. A 5-min delay between the extrusion of the material from the capsule and light curing had no significant effect on any of the measured properties. A significant effect of the accelerated aging solutions on macro-mechanical properties was observed, with ethanol and alkaline solutions having a particularly detrimental effect. In conclusion, light curing was preferable to self-curing, as it resulted in significantly better micro- and macro-mechanical properties, while a 5-min delay between mixing the capsule and light curing had no negative effects.
ABSTRACT
Objectives: The aim of the study was to assess the biocompatibility of modern composite and amalgam dental fillings. Material and Methods: The research was conducted on 150 healthy patients between the ages of 10 and 20 who had amalgam and composite fillings between 6 and 12 months. Under in vivo conditions, a swab of buccal cells near the fillings was taken, and the cytotoxic and genotoxic impact of composite and amalgam fillings on these cells was analyzed using the extended micronucleus test (cytomeassay). Results: The results showed statistically significant differences between the groups of subjects with amalgam and composite fillings and subjects without fillings for the following parameters: number of micronuclei (p=0.006), number of buds (p<0.001), number of binuclear cells (p<0.001), number of nucleoplasmic bridges (p<0.001).The number of micronuclei was statistically significantly higher in the group of subjects with amalgam and composite fillings compared to the group without fillings. The results for nuclear buds, for the number of binuclear cells and the number of nucleoplasmic bridges showed that the group with amalgam fillings had a statistically significantly higher number of these changes compared to other groups.The results of the analysis of the relationship between the parameters of the micronucleus test and the number of amalgam and composite surfaces did not show statistically significant values. Parameters indicating cell cytotoxicity were not statistically significantly elevated in subjects with fillings. The results of the analysis of the influence of the patients' lifestyle on the results of the micronucleus test showed statistically significant results for certain predictors (diagnostic X-ray radiation, coffee consumption, consumption of cooked, dried meat and baked food). Conclusion: Based on the results, it can be concluded that the buccal cells of subjects with amalgam fillings showed the highest degree of genotoxic changes, followed by those with composite fillings and the least buccal cells of patients without fillings.
ABSTRACT
Objective: To compare the effectiveness of reciprocating instruments in removing gutta-percha and bioactive-based (BioRoot RCS and MTA Fillapex) and epoxy resin-based (AH Plus) sealers from root canals based on filling residues and the time required for root canal revision. Material and methods: Root canals of 90 teeth were instrumented with Reciproc R40. All root canals were obturated using the single-cone technique with Reciproc R40 gutta-percha and with one of the selected sealers. Samples with oval, straight canals were used and randomly divided into three groups: (i) filled with AH Plus sealer and gutta-percha (n=30); (ii) filled with MTA Fillapex and gutta-percha (n=30); (iii) filled with BioRoot RCS and gutta-percha (n=30). Each group was divided into two subgroups (n=15) according to the retreatment instrument used (Reciproc M-Wire R25/R40 or Reciproc blue RB25/RB40). Root canals were longitudinally split and analyzed with a stereomicroscope at 15 × magnifications in the coronal, middle, and apical third. Computational analyses were performed with the Image J software. Data were compared using the Kruskal-Wallis test and Mann-Whitney U test. Results: While no statistically significant differences in the residual material surface were found for Reciproc Blue, Reciproc M-Wire showed significantly higher residual material surface for AH Plus and MTA Fillapex compared to BioRoot RCS. For AH plus. Residual material surface was significantly lower for Reciproc Blue than for Reciproc M-Wire. In contrast, BioRoot RCS showed a significantly higher residual material surface for Reciproc Blue. Conclusions: Calcium silicate-containing sealers were more retrievable compared to AH Plus, with fewer sealer remnants and shorter retreatment time. Retreatment with Reciproc M-Wire instruments was superior to Reciproc blue instruments in retreatment of BioRoot RCS. However, none of the sealers were removed completely.