ABSTRACT
Precise morphology design and electronic structure regulation are critically significant to promote catalytic activity and stability for electrochemical hydrogen production at high current density. Herein, the carbon nanotube (CNT) encapsulated Fe-doped NiCoP nanoparticles is in-situ grown in hierarchical carbonized wood (NCF0.5 P@CNT/CW) for water splitting. Coupling merits of porous carbonized wood (CW) substrate, CNT encapsulating and Fe doping, the NCF0.5 P@CNT/CW features remarkable and durable electrocatalytic activity. The overpotentials of NCF0.5 P@CNT/CW at 50 mA cm-2 mV and 205 mV for oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) and features high current density of 800 mA cm-2 within 300 mV for both OER and HER. Moreover, NCF0.5 P@CNT/CW displays outstanding overall water splitting performance (η50 = 1.62 V and η100 = 1.67 V), outperforming Pt/CâRuO2 (η50 = 1.74 V), and can achieve the current density of 700 mA cm-2 at a lower cell voltage of 1.78 V. Overpotential is only 4.0 % decay after 120 h measurement at 50 mA cm-2 . Density functional theory (DFT) calculations reveals Fe doping optimizes the binding energy and Gibbs free energy of intermediates, and regulates d-band center of NCF0.5 P@CNT/CW. Such synergistic strategy of morphology manipulation and electronic structure optimization provides a spark for developing effective and robust bifunctional catalysts.
ABSTRACT
Soil microorganisms play important roles in promoting soil ecosystem restoration, but much of the current research has been limited to changes in microbial community structure in general, and little is known regarding the soil physicochemical property and microbial community structure. In this study, four organic fertilizers were first prepared based on tea oil camellia shell (TOCS). Our findings indicate that the application of BOFvo increased both total pore volume and BET surface area of the rhizosphere soils, as well there was a remarkable enhancement in total organic matter (TOM), total nitrogen (TN), available nitrogen (AN), total phosphorus (TP), total potassium (TK), and available potassium (AK) contents of the rhizosphere soils. Meanwhile, in comparison to the CK and CF groups, the utilization of BOFvo led to a substantial increase in both average yield and fruiting rate per plant at maturity, as well resulted in a significant increase in TN and TP contents of tea oil camellia leaves. Furthermore, our findings suggest that the application of TOCS-based organic fertilizers significantly enhances the microbial diversity in the rhizosphere soils with Proteobacteria and Ascomycota being the dominant bacterial and fungal phyla, respectively, and Rhodanobacter and Fusarium being the dominant bacterial and fungal genus, respectively. Redundancy analysis (RDA) indicates that the physicochemical characteristics of TOCS-based organic fertilizers had a significant impact on the composition and distribution of microbial communities in the rhizosphere soils. This study will facilitate the promotion and application of TOCS-based organic fertilizers, thereby establishing a foundation for the reuse of tea oil camellia waste resources.
ABSTRACT
To optimize the bamboo heat treatment process, the corresponding evolution rules under various heat treatment conditions must be determined. When the heat treatment time and temperature remained constant, the effects of different heat treatment pressures on the equilibrium moisture content, dimensional stability, mechanical properties, and chemical composition of bamboo were systematically investigated. In this experiment, bamboo without heat treatment was used as the control group. The experimental findings demonstrate the following: (1) The equilibrium moisture content of heat-treated bamboo gradually decreases with increasing treatment pressure. When the heat treatment pressure was set at 0.1, 0.15, 0.2, and 0.25 MPa, the bamboo's equilibrium water content decreased to 12.1%, 11.7%, 9.9%, and 8.6%, respectively, while that of the control group was 13.8%. (2) The dimensional stability of bamboo was enhanced with increasing heat treatment pressure. At pressures of 0.1, 0.15, 0.2, and 0.25 MPa, the radial air-dry shrinkage rates of the heat-treated bamboo decreased to 3.4%, 3.4%, 2.6%, and 2.3%, respectively, while the tangential air-dry shrinkage rates reduced to 5.6%, 5.1%, 3.3%, and 3.0%. In comparison, the radial and tangential air-dry shrinkage rates of the control group were measured as 3.6% and 5.8%, respectively. Similarly, the radial and tangential full-dry shrinkage of bamboo exhibited a similar trend. (3) With the increase in heat treatment pressure, the bending strength and longitudinal compressive strength of bamboo exhibited an initial rise followed by a decline. When it was at heat treatment pressures of 0.1, 0.15, 0.2, and 0.25 MPa, the corresponding bending strengths of the heat-treated bamboo were measured as 41.2, 26.7, 22.4, and 20.4 MPa, respectively; while the longitudinal compressive strengths were recorded as 42.6, 38.1, 29.1, and 25.3 MPa. In comparison, the bending and longitudinal compressive strengths of the control group were measured as 39.8 and 38.5 MPa, respectively. It is evident that the optimal heat treatment pressure for bamboo is 0.1 MPa, resulting in a significant increase of 3.5% and 10.6% in bending strength and longitudinal compressive strength, respectively, compared to the control group. (4) Based on the FTIR and XRD patterns of bamboo samples, a range of physical and chemical transformations were observed during the heat treatment process, including cellulose adsorb water evaporation, hemicellulose and cellulose degradation, as well as acetyl group hydrolysis on the molecular chain of hemicellulose. These changes collectively impacted the physical and mechanical properties of bamboo.
ABSTRACT
This study investigated the improved properties of calcium carbonate (CaCO3) modified urea-formaldehyde (UF) resin adhesive for medium density fiberboard (MDF) production. The CaCO3 modified UF resins were prepared by adding different proportions of CaCO3 to a low molar ratio UF resin at the initial stage of a typical synthetic process of the resin. The physicochemical properties of the resins were measured. The mechanical and environmental performances of the resin-bonded MDF panels were tested. The results show that the viscosity and free formaldehyde content of UF resins with or without CaCO3 modification were not significantly different. The solid content of the CaCO3 modified UF resin was significantly lower than that of the control group. In addition, the measured gel time of the CaCO3 modified UF resin was 111-149 s, which was longer than that of the control resin (82 s). The gel time was further extended with the increase of the CaCO3 content in the UF resin. The chemical group and crystal structure of UF resins with or without the modification of CaCO3 were not significantly different. The internal bonding (IB) strength of the MDF panels significantly increased from 0.75 MPa to 0.97 MPa when the UF resin was modified with 2% of CaCO3. This study provides scientific support for the preparation of inorganic mineral modified UF resins for strength enhanced wood-based panel manufacturing.