Application of the EBSD Technique in the Study of Porosity and Permeability in Deformation Bands in Sandstone.

Deformation bands are common constituents of porous clastic fluid reservoirs. Various techniques have been used to study deformation band structure and the associated changes in porosity and permeability. However, the use of electron backscatter diffraction technique is limited. Thus, more information is needed regarding the crystallographic relationships between detrital crystals, which can significantly impact reservoir rock quality. We employ microscopic and microstructural investigation techniques to analyze the influence of cataclastic deformation bands on pore space. Porosity measurements of the Cretaceous Ilhas Group sandstone in NE Brazil, obtained through computerized microtomography, indicate that the undeformed domains exhibit a total porosity of up to 13%. In contrast, this porosity is slightly over 1% in the deformation bands. Scanning electron microscopy analyses revealed the presence of grain fragmentation and dissolution microstructures, along with cement-filling pre-existing pores. The electron backscatter diffraction analyses indicated extensive grain fragmentation and minimal contribution from intracrystalline plasticity as a deformation mechanism. However, the c axes of quartz crystals roughly align parallel to the orientation of the deformation band. In summary, we have confirmed and quantified the internal changes in a deformation band cluster, with grain size reduction and associated compaction as the main mechanism supported by quartz cementation.

Manipulating Ion Transport Regimes in Nanomembranes via a "Pore-in-Pore" Approach Enabled by the Synergy of Metal-Organic Frameworks and Solid-State Nanochannels.

Solid-state nanochannels (SSNs) have emerged as promising platforms for controlling ionic transport at the nanoscale. SSNs are highly versatile, and this feature can be enhanced through their combination with porous materials such as Metal-Organic Frameworks (MOF). By selection of specific building blocks and experimental conditions, different MOF architectures can be obtained, and this can influence the ionic transport properties through the nanochannel. Herein, we study the effects of confined synthesis of Zr-based UiO-66 MOF on the ion transport properties of single bullet-shaped poly(ethylene terephthalate) (PET) nanochannels. We have found that emerging textural properties from the MOF phase play a determinant role in controlling ionic transport through the nanochannel. We demonstrate that a transition from ion current saturation regimes to diode-like regimes can be obtained by employing different synthetic approaches, namely, counterdiffusion synthesis, where MOF precursors are kept separate and forced to diffuse through the nanochannel, and one-pot synthesis, where both precursors are placed at both ends of the channel. Also, by considering the dependence of the charge state of the UiO-66 MOF on the protonation degree, pH changes offered a mechanism to tune the iontronic output (and selectivity) among different regimes, including anion-driven rectification, cation-driven rectification, ion current saturation, and ohmic behavior. Furthermore, Poisson-Nernst-Planck (PNP) simulations were employed to rationalize the different iontronic outputs observed experimentally for membranes modified by different methods. Our results demonstrate a straightforward tool to synthesize MOF-based SSN membranes with tunable ion transport regimes.

Relevance of Specific Surface of Mixed Oxide Derived from Layered Double Hydroxides on the Rheological Properties and Porosity of Cement Pastes.

Cement-based products are the synthetic materials most used by humans, with consequent environmental impacts. One strategy that can assist in mitigating the adverse environmental effects of these materials involves the incorporation of multifunctional nanostructured additives. The objective of this work was to demonstrate the efficacy of incorporating mixed oxides (MO) derived from layered double hydroxides (LDH) to control the rheology and porosity of cement-based matrices. Thermal aging of LDH enabled the preparation of MO with different specific surface areas (SSA) for incorporation in different amounts in Portland cement. A low proportion of MO and low SSA increased workability by 22%. In contrast, a high proportion of MO and high SSA led to a 2.4-fold acceleration of cement consolidation and a 36.9% decrease of the porosity of the composite. These features could be attributed to additive-matrix interactions, with the LDH memory effect playing key roles in the cement crystal seed process and in competition for the absorption of free water within the cement paste. Therefore, the unprecedent results obtained suggest that the quantity and SSA of MO are key parameters to fine-tune the paste rheology and structure of hidrated cement. The MO materials showed easy adaptability and excellent potential for use as multifunctional additives in the production of eco-friendly, high-performance cement paste formulations with controllable properties according to the desired application.

Analysis of the Chemical Composition, Morphological Characterization, and Porosimetry of Allograft and Comparison with Xenograft for Dental Applications / Análisis de la Composición Química, Caracterización Morfológica y Porosimetría de Aloinjerto y Comparación con Xenoinjerto para Aplicaciones Odontológicas

SUMMARY: Tissue engineering aims to fabricate a scaffold that exhibits a suitable surface topography for a desired cellular response. Therefore, a study analyzing the characteristics of bone grafts is important for future research directions. This work aims to analyze the physical-chemical characteristics of commercially available bone grafts of human and bovine origin for dental use, using morphological analysis of the surface and chemical composition by variable pressure scanning electron microscope (VP-SEM) and energy-dispersive x-ray (EDX) spectrometry. In addition, pore diameter and surface area were analyzed by degassing method using a porosimeter, and particle size by laser diffraction. The analyzed allograft and xenograft particles differ in morphological characteristics and chemical composition. The allograft particles present a cuboidal and prismatic geometric morphology with angled edges and the absence of macropores. On the contrary, the xenograft particles present an irregular morphology with macropores in their structure. There is a statistically significant difference in C, P, and Ca between the xenograft and allografts (p < 0,05). The analyzed composition of allografts showed mainly the presence of C and O. In contrast, the composition of the xenograft was mainly Ca. These differences could influence the osteogenic properties of allografts and xenografts. This analysis provides basic information to understand the physicochemical properties of allografts and xenografts that facilitate cell-graft interaction.

La ingeniería de tejidos tiene como objetivo fabricar un andamio que muestre una topografía de superficie adecuada para una respuesta celular deseada. Por tanto, un estudio que analice las características de los injertos óseos es importante para futuros enfoques de investigación. Este trabajo tiene como objetivo analizar las características físico-químicas de injertos óseos de origen humano y bovino disponibles comercialmente para uso odontológico, mediante análisis morfológico de la superficie y composición química mediante microscopio electrónico de barrido de presión variable (VP-SEM) y x-dispersivo de energía. espectrometría de rayos (EDX). Además, el diámetro de los poros y el área superficial se analizaron mediante el método de desgasificación utilizando un porosímetro y el tamaño de las partículas mediante difracción láser. Las partículas de aloinjerto y xenoinjerto analizadas difieren en características morfológicas y composición química. Las partículas del aloinjerto presentan una morfología geométrica cúbica y prismática con bordes angulados y ausencia de macroporos. Por el contrario, las partículas de xenoinjerto presentan una morfología irregular con macroporos en su estructura. Existe una diferencia estadísticamente significativa en C, P y Ca entre el xenoinjerto y los aloinjertos (p < 0,05). La composición analizada de los aloinjertos mostró principalmente la presencia de C y O. Por el contrario, la composición del xenoinjerto fue principalmente Ca. Estas diferencias podrían influir en las propiedades osteogénicas de los aloinjertos y xenoinjertos. Este análisis proporciona información básica para comprender las propiedades fisicoquímicas de aloinjertos y xenoinjertos que facilitan la interacción célula-injerto.

Influences of Recycled Polyethylene Terephthalate Microplastic on the Hygrothermal and Mechanical Performance of Plasterboard with Polymethylhydrosiloxane Content.

New composites produced with recycled waste are needed to manufacture more sustainable construction materials. This paper aimed to analyze the hygrothermal and mechanical performance of plasterboard with a polymethylhydrosiloxane (PMHS) content, incorporating recycled PET microplastic waste and varying factors such as PMHS dose, homogenization time, and drying temperature after setting. A cube-centered experimental design matrix was performed. The crystal morphology, porosity, fluidity, water absorption, flexural strength, and thermal conductivity of plasterboards were measured. The results showed that incorporating recycled PET microplastics does not produce a significant difference in the absorption and flexural strength of plasterboards. However, the addition of recycled PET reduced the thermal conductivity of plasterboards by around 10%.

Estimation of Digital Porosity of Electrospun Veils by Image Analysis.

The present work reports on an empirical mathematical expression for predicting the digital porosity (DP) of electrospun nanofiber veils, employing emulsions of poly(vinyl alcohol) (PVOH) and olive and orange oils. The electrospun nanofibers were analyzed by scanning electron microscopy (SEM), observing orientation and digital porosity (DP) in the electrospun veils. To determine the DP of the veils, the SEM micrographs were transformed into a binary system, and then the threshold was established, and the nanofiber solid surfaces were emphasized. The relationship between the experimental results and those obtained with the empirical mathematical expression displayed a correlation coefficient (R2) of 0.97 by employing threshold II. The mathematical expression took into account experimental variables such as the nanofiber humidity and emulsion conductivity prior to electrospinning, in addition to the corresponding operation conditions. The results produced with the proposed expression showed that the prediction of the DP of the electrospun veils was feasible with the considered thresholds.

Effects of blood and root-dentin cleaning on the porosity and bond strength of a collagen bioceramic material

Abstract To assess the effect of cleaning protocols on dentin contaminated with blood in reparative endodontic materials, bovine root samples were divided: no contamination (N); contamination (P); contamination and cleaning with saline (S), 2.5% NaOCl+saline (Na) or 2.5% NaOCl+17% EDTA+saline (NaE) and filled with: mineral trioxide aggregate (MTA), calcium-aluminate-cement (C), or C+collagen (Ccol) (n=13). The samples were evaluated for porosity, chemical composition, and bond strength. MTA porosity was lower than C (p=0.02) and higher than Ccol (p<0.001). P and NaE were similar (p=1.00), but higher than the other groups (p<0.001). MTA bond strength was similar to Ccol (p=0.777) and lower than C (p=0.028). P presented lower bond strength than the N (p<0.001); S and Na were similar to each other (p=0.969), but higher than P and lower than N (p<0.001). It was observed a predominance of mixed and cohesive failures. None of the samples showed Ca/P ratio values similar to human hydroxyapatite. This study showed that contamination with blood increased the materials porosity, but dentin cleaning with 2.5% NaOCl reduced this effect, and the collagen additive reduced the material porosity. Furthermore, blood contamination reduced the materials bond strength, and cleaning with saline or 2.5% NaOCl diminished this effect.

Resumo As amostras de raízes bovinas foram divididas em: sem contaminação (N); contaminação sanguínea (P); contaminação sanguínea e limpeza com soro fisiológico (S), 2,5% NaOCl+soro fisiológico (Na) ou 2,5% NaOCl+17%EDTA+soro fisiológico (NaE) e preenchido com: agregado de trióxido mineral (MTA), cimento de aluminato de cálcio (C), ou C+colágeno (Ccol) (n=13). A porosidade do MTA foi menor que C (p=0,02) e maior que Ccol (p<0,001). P e NaE foram semelhantes (p=1,00), mas superiores aos demais grupos (p<0,001). A resistência de união do MTA foi semelhante ao Ccol (p=0,777) e inferior ao C (p=0,028). P apresentou menor resistência de união que o N (p<0,001); S e Na foram semelhantes entre si (p=0,969), porém maiores que P e menores que N (p<0,001). Este estudo mostrou que a contaminação com sangue aumentou a porosidade dos cimentos, mas a limpeza da dentina com NaOCl 2,5% reduziu esse efeito, e o aditivo de colágeno reduziu a porosidade dos cimentos. Além disso, a contaminação sanguínea reduziu a resistência de união dos cimentos e a limpeza com solução salina ou NaOCl 2,5% diminuiu esse efeito.

Simulation of the Influence of the Radial Graded Porosity Distribution on Elastic Modulus of γ/ß Phase Ti-Based Alloy Foams for Bone Implant.

This research aims to examine how a radial graded porosity distribution affects the elastic modulus by conducting simulations on Ti-based alloy foams with face-centered cubic and body-centered cubic crystal structures. Four types of foams were analyzed; commercially pure-Ti, Ti-13Ta-6Mn (TTM), Ti-13Ta-(TT) and Ti-13Ta-6Sn (TTS), (all in at.%). Four radial graded porosity distribution configurations were modeled and simulated using the finite element analysis (FEA). The radial graded porosity distribution configurations were generated using a Material Designer (Ansys) with a pore range of 200 to 600 µm. These radial graded porosity distributions had average porosity values of 0, 20, 30 and 40%. The consolidated samples that were obtained through a powder metallurgy technique in two step samples were synthesized using a powder metallurgy technique, with the elastic moduli values of the aforementioned Ti based alloys being measured by ultrasound using ~110, ~69, ~61 and ~65 GPa, respectively. The results showed that the modulus decreased as a function of porosity level in all simulated materials. The TTM, TT and TTS foams, with average porosities of 20, 30 and 40%, exhibited an modulus smaller than 30 GPa, which is a requirement to be used as a biomaterial in human bones. The TT foams showed the lowest modulus when compared to the other foams. Finally, certain theoretical models were used to obtain the modulus, the best being; the Gibson-Ashby model (α = 1 and n = 2.5) for the cp-Ti foams and Knudsen-Spriggs model (b = 3.06) for the TTM, TT and TTS foams.

Analysis of Novel Porosity-Water-to-Binder Index for Prediction of Strength, Stiffness and Durability for Cemented Soils.

The initial weight and volume relationships are crucial factors in determining the strength, stiffness, and durability of cement-stabilized soils. The porosity/binder ratio has been widely used as a control parameter for stabilized soil mixtures. However, this approach does not take into consideration the water content used during the stabilization process, which can impact the strength and durability of the final product. To address this issue, this paper introduces the porosity-water/binder relationship as a new parameter to predict the strength, stiffness (Go), and durability against wetting-drying cycles of artificially cemented soils. The strengths, Go, and accumulated losses of mass (ALM) of different stabilized soils were compared based on this new parameter, and the comprehensive results were analyzed to demonstrate its effectiveness. The findings indicate that the new parameter is a suitable design parameter for soil-lime, soil-cement, and geopolymerized soil mixtures. Furthermore, it was determined that the water content has no effect on the splitting tensile strength to compressive strength ratio. The results of this study offer valuable insights into the optimization of stabilized soils and the development of improved soil stabilization processes.

Effect of the incorporation of pregelatinized cassava starch on the physicochemical, textural, and acoustic characteristics of baked snacks.

Almost all the dehydrated cassava puree is pregelatinized cassava starch (PCS). Its potential application in food would add variety. But food characteristics vary depending on the raw materials used. We examined how the structure of snacks changed when PCS was used instead of flour in terms of porosity, instrumental textural parameters, and acoustic parameters and compare them to commercial crackers. The volume of air was unaffected by the substitution. However, substitution did reduce thickness and alter the number, size, and wall firmness of pores, as well as their distribution and shape, which raise the values of firmness, fracturability, hardness, and fragility, though not linearly. The partial substitutions and the control did not exhibit any appreciable differences in the acoustic parameters. The total replacement sample was noisier and maintained a wide variety of sounds. The PCS vitreous state is primarily responsible for structure changes, but other elements, such as processing conditions, contribute to differences in comparison to the commercial samples. The porosity of commercial samples was lower than that of the elaborated samples. Texturally, it led to lower fracturability and greater fragility (less mm until fracture and fewer force peaks). The elaborated samples were all louder than the commercials. Although sensory analysis is required to classify a food as crunchy, the physicochemical changes caused by the substitution and their impact on the structure's behavior were established. Each textural parameter cannot determine whether the food is crunchy, crispy, or friable on its own; an analysis that incorporates all the characteristics is required. Supplement Material. PRACTICAL APPLICATION: This study demonstrates that pregelatinized cassava flour can be used to partially or completely replace wheat flour in baked snacks. Although textural differences were noted, these alterations were acceptable for products with a similar market niche. These findings might be used in the food business, notably by companies aiming to offer baked snack choices that are not made with standard wheat flour.

Strength, Stiffness, and Microstructure of Stabilized Marine Clay-Crushed Limestone Waste Blends: Insight on Characterization through Porosity-to-Cement Index.

The porosity-to-cement index (η/Civ) has been extensively applied to study the evolution of different types of soil stabilization. However, this index has still not been used to characterize soils cemented with crushed limestone waste (CLW). In this sense, this paper sought to analyze the applicability of the porosity-to-cement index over the unconfined compressive strength (qu) and initial stiffness at small deformations (Go) of clayey soil improved with CLW and Portland cement. In addition, a microstructural analysis (SEM and EDX tests) was also conducted. CLW addition increased soil strength and stiffness over time. Moreover, qu and Go compacted mixtures containing CLW have established a distinctive correlation. Chemical microanalyses have uncovered a complex interfacial interaction between the soil, cement, and fine CLW particles, leading to a notable reduction in porosity.

Improvement of Plasterboard Properties by the Control of Polymethylhydrosiloxane Dosage, Stirring Time, and Drying Temperature Applied to the Calcium Sulfate Hemihydrate and Water Mixture.

Plasterboard is an important building material in the construction industry because it allows for quick installation of walls, partitions, and ceilings. Although a common material, knowledge about its performance related to modern polymers and fabrication conditions is still lacking. The present work analyzes how some manufacturing factors applied during the plaster board fabrication impact on some plasterboard properties, including water absorption, flexural strength, and thermal conductivity. The manufacturing variables evaluated are the dose (D) of polymethylhydrosiloxane (PMHS), the agitation time of the mixture (H), and the drying temperature of the plaster boards after setting (T). The results suggest that factors D, H, and T induce changes in the porosity and the morphological structure of the calcium sulfate dihydrate crystals formed. Performance is evaluated at two levels of each factor following a statistical method of factorial experimental design centered on a cube. Morphological changes in the crystals of the resulting boards were evaluated with scanning electron microscopy (SEM) and the IMAGEJ image analysis program. Porosity changes were evaluated with X-ray microcomputed tomography (XMT) and 3D image analysis tools. The length-to-width ratio of the crystals decreases as it goes from low PMHS dosage to high dosage, favoring a better compaction of the plasterboard under the right stirring time and drying temperature. In contrast, the porosity generated by the incorporation of PMHS increases when going from low-level to high-level conditions and affects the maximum size of the pores being generated, with a maximum value achieved at 0.6% dosage, 40 s, and 140 °C conditions. The presence of an optimal PMHS dosage value that is approximately 0.6-1.0% is evidenced. In fact, when comparing trails without and with PMHS addition, a 10% decrease in thermal conductivity is achieved at high H (60 s) and high T (150 °C) level conditions. Water absorption decreases by more than 90% when PMHS is added, mainly due to the hydrophobic action of the PMHS. Minimum water absorption levels can be obtained at high drying temperatures. Finally, the resistance to flexion is not affected by the addition of PMHS because apparently there are two opposing forces acting: on one hand is the decrease in the length-width ratio giving more compactness, and on the other hand is the generation of pores. The maximum resistance to flexion was found around a dosage of 0.6% PMHS. In conclusion, the results suggest that the addition of PMHS, the correct agitation time of the mixture, and the drying temperature reduce the water absorption and the thermal conductivity of the gypsum boards, with no significant changes in the flexural resistance.

A comprehensive study of product distributions and coke deposition during catalytic cracking of vacuum gas oil over hierarchical zeolites.

In this study, zeolites (Z) were used as catalysts in the cracking of a Colombian vacuum gas oil (VGO), with a focus on product distribution and coke deposition. The catalytic tests were carried out in a MAT-type reactor under typical conditions. The zeolites were subjected to alkaline treatment with NaOH at concentrations ranging from 0.05 to 0.4 mol/L, resulting in the creation of several samples (Z-0.05, Z-0.10, Z-0.20, Z-0.30 and Z-0.40) that were then hydrothermally stabilized (Z-0.05-M, Z-0.10-M, Z-0.20-M, Z-0.30-M and Z-0.40-M) to increase mesoporosity and reduced crystallinity. The increase in mesoporosity was accompanied by an improvement in acidity. Despite Z-0.30-M having higher acidity, Z-0.00-M and Z-0.10-M exhibited the highest activity due to their high crystallinity and microporosity, yielding the highest gas yields. Gasoline was the main product, with maximum yields exceeding 30%. Z-0.20-M produced more aromatic and olefin compounds than the others, resulting in higher quality gasoline. Coke formation followed the trend: Z-0.00-M < Z-0.10-M < Z-0.20-M < Z-0.30-M. The higher intracrystalline mesoporosity in the zeolites favored the formation of a more condensed coke.

Porous Structural Properties of K or Na-Co Hexacyanoferrates as Efficient Materials for CO2 Capture.

The stoichiometry of the components of hexacyanoferrate materials affecting their final porosity properties and applications in CO2 capture is an issue that is rarely studied. In this work, the effect that stoichiometry of all element components and oxidation states of transition metals has on the structures of mesoporous K or Na-cobalt hexacyanoferrates (CoHCFs) and CO2 removal is reported. A series of CoHCFs model systems are synthesized using the co-precipitation method with varying amounts of Co ions. CoHCFs are characterized by N2 adsorption, TGA, FTIR-ATR, XRD, and XPS. N2 adsorption results reveal a more developed external surface area (72.69-172.18 m2/g) generated in samples containing mixtures of K+/Fe2+/Fe3+ ions (system III) compared to samples with Na+/Fe2+ ions (systems I, II). TGA results show that the porous structure of CoHCFs is affected by Fe and Co ions oxidation states, the number of water molecules, and alkali ions. The formation of two crystalline cells (FCC and triclinic) is confirmed by XRD results. Fe and Co oxidation states are authenticated by XPS and allow for the confirmation of charges involved in the stabilization of CoCHFs. CO2 removal capacities (3.04 mmol/g) are comparable with other materials reported. CO2 adsorption kinetics is fast (3-6 s), making CoHCFs attractive for continuous operations. Qst (24.3 kJ/mol) reveals a physical adsorption process. Regeneration effectiveness for adsorption/desorption cycles indicates ~1.6% loss and selectivity (~47) for gas mixtures (CO2:N2 = 15:85). The results of this study demonstrate that the CoHCFs have practical implications in the potential use of CO2 capture and flue gas separations.

Biomechanical performance of three fiberglass post cementation techniques: Imaging, in vitro, and in silico analysis.

PURPOSE: The structural integrity of the resin cement layer, the bond strength, and the biomechanical behavior of different fiberglass post cementation techniques were evaluated. METHODS: Thirty-three bovine incisors were divided into three groups (n = 11): conventional fiberglass post (CFP), conventional fiberglass post in flared root canals (CFL), and relined fiberglass post (RFP). Six specimens from each group were submitted for high-resolution microcomputed tomography (µCT) to evaluate the integrity and presence/volume of voids at the resin cement layer. Finite element analysis (FEA) of two three-dimensional (3D) models of each group were conducted, one considered ideal (without interface defects) and another containing the conditions identified in the µCT analysis. Push-out bond strength tests were conducted for all specimens. RESULTS: The CFL group had the greatest mean values of void (Thirds cervical: 73.67; middle: 95.67; apical: 47.33) and gap concentration (Thirds cervical: 14.67; middle: 15.83; apical: 8.33) compared with CFP and RFP. A significant difference in bond strength was observed between the cervical (1.33 MPa) and middle thirds (1.85 MPa) compared with the apical third (4.85 MPa) of the CFL. A significant difference was observed in the bond strength in the CFL (1.33 MPa) and RFP (3.29 MPa) in the cervical third, which were statistically similar to the bond strength of the CFP. The tensile stress distributions were similar in most structures, localized in the cervical region on the lingual surface. CONCLUSIONS: Structural defects in the interface layer might influence the bond strength and biomechanical behavior under the different fiberglass post cementations.

Soil deep tillage performed before soybean cultivation on the rice cultivation in the following harvest / Efeito remanescente da escarificação do solo realizada antes do cultivo da soja, sobre o cultivo de arroz na safra seguinte

ABSTRACT: Soil decompaction is an alternative for soybean cultivation in rice areas, but it can affect the growth of irrigated rice in rotation. The objective of the study was to evaluate the effects of soil deep tillage performed before soybean cultivation on rice irrigation water, grain yield, and operational parameters of rice sowing carried out in the following crop season. Soil scarification was implemented in September 2017, prior to soybean crop season in the 2017/18 crop, and the rice experiment was conducted in the 2018/19 season. Treatments were: soil with scarification and soil without scarification. Deep tillage decreased soil density and increased macroporosity, microporosity, and total porosity. Rice cultivation decreased macroporosity and increased microporosity. Soil scarification management had no influence on operational parameters in rice sowing. Soil with scarification required 5.3% more water for rice irrigation than soil without deep tillage. In conclusion, soildeep tillage before the cultivation of soybean crop has effects on rice in thefollowing crop season, maintaining greater soil porosity in relation to the non-deep tillage area and increasing the amount of water needed for irrigation of rice cultivated in the sequence. Deep tillage did not affect sowing operational parameters and rice grain yield.

RESUMO: A descompactação do solo é uma alternativa para o cultivo da soja em áreas de arroz, mas pode afetar o desenvolvimento do arroz irrigado em rotação. O objetivo do estudo foi avaliar o efeito remanescente da escarificação do solo realizada antes do cultivo da soja, sobre o uso da água de irrigação, o rendimento de grãos e parâmetros operacionais da semeadura do arroz, realizada na safra seguinte. A escarificação do solo foi feita no mês de setembro de 2017, anteriormente à soja na safra 2017/18 e o experimento de arroz foi conduzido na safra 2018/19. Os tratamentos foram:escarificação e não escarificação do solo. A escarificação aumentou a macroporosidade, a microporosidade e a porosidade total e diminuiu a densidade do solo. O cultivo do arroz reduziu a macroporosidade e aumentou a microporosidade. Não se observou influência do manejo de escarificação do solo sobre os parâmetros operacionais na semeadura do arroz. O solo escarificado necessitou 5,3 % a mais de água para irrigação do arroz, em relação ao solo não escarificado. Conclui-se que a escarificação do solo antes do cultivo da cultura da soja tem efeito remanescente em arroz na safra seguinte, mantendo maior porosidade do solo em relação à área não escarificada e elevando a quantidade de água necessária para irrigação do arroz cultivado na sequência. Não se verificou interferência da escarificação em parâmetros operacionais da semeadura e sobre o rendimento de grãos do arroz.

Soil deep tillage performed before soybean cultivation on the rice cultivation in the following harvest / Efeito remanescente da escarificação do solo realizada antes do cultivo da soja, sobre o cultivo de arroz na safra seguinte

Soil decompaction is an alternative for soybean cultivation in rice areas, but it can affect the growth of irrigated rice in rotation. The objective of the study was to evaluate the effects of soil deep tillage performed before soybean cultivation on rice irrigation water, grain yield, and operational parameters of rice sowing carried out in the following crop season. Soil scarification was implemented in September 2017, prior to soybean crop season in the 2017/18 crop, and the rice experiment was conducted in the 2018/19 season. Treatments were: soil with scarification and soil without scarification. Deep tillage decreased soil density and increased macroporosity, microporosity, and total porosity. Rice cultivation decreased macroporosity and increased microporosity. Soil scarification management had no influence on operational parameters in rice sowing. Soil with scarification required 5.3% more water for rice irrigation than soil without deep tillage. In conclusion, soildeep tillage before the cultivation of soybean crop has effects on rice in thefollowing crop season, maintaining greater soil porosity in relation to the non-deep tillage area and increasing the amount of water needed for irrigation of rice cultivated in the sequence. Deep tillage did not affect sowing operational parameters and rice grain yield.

A descompactação do solo é uma alternativa para o cultivo da soja em áreas de arroz, mas pode afetar o desenvolvimento do arroz irrigado em rotação. O objetivo do estudo foi avaliar o efeito remanescente da escarificação do solo realizada antes do cultivo da soja, sobre o uso da água de irrigação, o rendimento de grãos e parâmetros operacionais da semeadura do arroz, realizada na safra seguinte. A escarificação do solo foi feita no mês de setembro de 2017, anteriormente à soja na safra 2017/18 e o experimento de arroz foi conduzido na safra 2018/19. Os tratamentos foram:escarificação e não escarificação do solo. A escarificação aumentou a macroporosidade, a microporosidade e a porosidade total e diminuiu a densidade do solo. O cultivo do arroz reduziu a macroporosidade e aumentou a microporosidade. Não se observou influência do manejo de escarificação do solo sobre os parâmetros operacionais na semeadura do arroz. O solo escarificado necessitou 5,3 % a mais de água para irrigação do arroz, em relação ao solo não escarificado. Conclui-se que a escarificação do solo antes do cultivo da cultura da soja tem efeito remanescente em arroz na safra seguinte, mantendo maior porosidade do solo em relação à área não escarificada e elevando a quantidade de água necessária para irrigação do arroz cultivado na sequência. Não se verificou interferência da escarificação em parâmetros operacionais da semeadura e sobre o rendimento de grãos do arroz.

Height-to-Diameter Ratio and Porosity Strongly Influence Bulk Compressive Mechanical Properties of 3D-Printed Polymer Scaffolds.

Although the architectural design parameters of 3D-printed polymer-based scaffolds-porosity, height-to-diameter (H/D) ratio and pore size-are significant determinants of their mechanical integrity, their impact has not been explicitly discussed when reporting bulk mechanical properties. Controlled architectures were designed by systematically varying porosity (30-75%, H/D ratio (0.5-2.0) and pore size (0.25-1.0 mm) and fabricated using fused filament fabrication technique. The influence of the three parameters on compressive mechanical properties-apparent elastic modulus Eapp, bulk yield stress σy and yield strain εy-were investigated through a multiple linear regression analysis. H/D ratio and porosity exhibited strong influence on the mechanical behavior, resulting in variations in mean Eapp of 60% and 95%, respectively. σy was comparatively less sensitive to H/D ratio over the range investigated in this study, with 15% variation in mean values. In contrast, porosity resulted in almost 100% variation in mean σy values. Pore size was not a significant factor for mechanical behavior, although it is a critical factor in the biological behavior of the scaffolds. Quantifying the influence of porosity, H/D ratio and pore size on bench-top tested bulk mechanical properties can help optimize the development of bone scaffolds from a biomechanical perspective.

In Vivo Modification of Microporous Structure in Bacterial Cellulose by Exposing Komagataeibacter xylinus Culture to Physical and Chemical Stimuli.

Bacterial cellulose (BC) samples were obtained in a static culture of K. xylinus under the effect of a low-intensity magnetic field, UV light, NaCl, and chloramphenicol. The effect of such stimuli on the amount of BC produced and its production rate, specific area, pore volume, and pore diameter were evaluated. The polysaccharide production was enhanced 2.28-fold by exposing K. xylinus culture to UV light (366 nm) and 1.7-fold by adding chloramphenicol (0.25 mM) to the medium in comparison to BC control. All the stimuli triggered a decrease in the rate of BC biosynthesis. BC membranes were found to be mesoporous materials with an average pore diameter from 21.37 to 25.73 nm. BC produced under a magnetic field showed the lowest values of specific area and pore volume (2.55 m2 g-1 and 0.024 cm3 g-1), while the BC synthesized in the presence of NaCl showed the highest (15.72 m2 g-1 and 0.11 cm3 g-1). FTIR spectra of the BC samples also demonstrated changes related to structural order. The rehydration property in these BC samples is not mainly mediated by the crystallinity level or porosity. In summary, these results support that BC production, surface, and structural properties could be modified by manipulating the physical and chemical stimuli investigated.

Switchable Ion Current Saturation Regimes Enabled via Heterostructured Nanofluidic Devices Based on Metal-Organic Frameworks.

The use of track-etched membranes allows further fine-tuning of transport regimes and thus enables their use in (bio)sensing and energy-harvesting applications, among others. Recently, metal-organic frameworks (MOFs) have been combined with such membranes to further increase their potential. Herein, the creation of a single track-etched nanochannel modified with the UiO-66 MOF is proposed. By the interfacial growth method, UiO-66-confined synthesis fills the nanochannel completely and smoothly, yet its constructional porosity renders a heterostructure along the axial coordinate of the channel. The MOF heterostructure confers notorious changes in the transport regime of the nanofluidic device. In particular, the tortuosity provided by the micro- and mesostructure of UiO-66 added to its charged state leads to iontronic outputs characterized by an asymmetric ion current saturation for transmembrane voltages exceeding 0.3 V. Remarkably, this behavior can be easily and reversibly modulated by changing the pH of the media and it can also be maintained for a wide range of KCl concentrations. In addition, it is found that the modified-nanochannel functionality cannot be explained by considering just the intrinsic microporosity of UiO-66, but rather the constructional porosity that arises during the MOF growth process plays a central and dominant role.